HD capture & edit problem

Hi guys,
it's me again....this time is facing HD problem. i try to capture a hdcam tape from sony HD player. However, the problem im facing is i cant play back on my fcp. im using blackmagic hdtv 1080i 50-10 bit, remote is blackmagic pal 25hz... the capture file is: frame size 1920*1080, 25 fps, compressor is uncompressed 10 bit...n my edit sequence is the same wit it...
i cant view playback on boradcast mon, n visual also lack while playing on mac itself monitor...however, my spec is quite powerful...its dual 2.5 ghz g5 n 8gb ram..
plz tell me how to solve it out...

Sounds like it could be a data rate issue:
Here's a handy table to ensure your HDD's can cope. Doesn't mater how much RAM you have or how many gigs you CPU is, it's all about bandwidth on the HD bus.
Compressed formats Data Rate Gigs per hour
720 x 480 DV 4:1:1 25 11
720 x 480 DV50 4:2:2 50 22
HD-DVCPRO 100 44
Uncompressed 10-bit formats
720 x 486 4:2:0 210 92
1280 x 720/24p 4:2:0 332 146
1280 x 720/60p 4:2:0 818 364
1920 x 1080/24p 4:2:0 746 328
1920 x 1080/60i 4:2:0 932 410
You can download many apps that will test your data rate on both red and write.
AJA do one I believe.

Similar Messages

I have a 17" Macbook pro with flickering red and cyan(blue) lines across the screen. The issue disappears temporarily when I tap on the computer, and the problem does not occur when I use external display or try to screen capture the problem.

I purchased my Macbook (17") through a certified apple tecnition in August 2012, it was refurbished and the motherboard was completely replaced. I do a lot of photo editing, but I have been unable to do so because of the red vibrating lines that interrupt my screen. The issue disappears temporarily when I tap on the computer, and the problem does not occur when I use external display or try to screen capture the problem. I brought the computer back to the technition I purchased it from and he said that it was a problem with my fan, so I have two new fans but the issue is still occuring. He says he doesnt know whats wrong. Does anyone have any information on this issue?
Here is an image of the issue
http://www.flickr.com/photos/67839707@N08/8884847081/

I recommend having your Mac serviced by someone competent. A force sufficient to "blow apart" the fans was clearly excessive and may have damaged the display cable, as well as any number of other problems.
Dust is properly cleaned with a vacuum, preferably one designed for computer service, and they are not cheap.
Compressed air should never be used. It just blows dust everywhere, often into places where it can no longer be removed.

Font / text edit problem in photoshop CS6

Hi there,
I have a strange text edit problem in Photoshop CS6 running on Mavericks.
Every time I use the text-tool in PS, write a sentence, mark it and change something like color, font size etc., the marked text vanishes.
I have to "undo" the last step and the changed text appears again.
Every time!
I have a clean installed CS6 with no plugins and no other than system fonts installed.
Everything on a new Mac Pro with OS X 10.9.5
Any clues? Thanks.

Do you have the latest updates for photoshop cs6?
You can use Help>Updates from within photoshop cs6 to check if there are any available.
Also, if you go to Help>System Info from within photoshop cs6, you can see the Photoshop Version in the top line.
You should be on version 13.0.6
See if turning off Dictation solves the issue.
Go to System Preferences ---> Dictation and Speech -----> select OFF radio button .

From USB to IEEE-1394: question about HD capture, editing, sharing.

I’m new to editing video but have a question about capturing video into Premiere Elements 7. I have been using a Canon HF11 which shoots only in HD and only has USB output to copy video to my desktop. I don’t have a Blu-ray burner yet but I have burned a few projects to DVD, shared video on YouTube, and saved files in .avi and .mpeg to view on computer screens. But obviously I’m missing out on sharing HD on disk at this time. I just bought a Canon XH A1s which shoots both HD and SD on miniDV tapes. And uses IEEE-1394 cable for capturing (to Pre7). I did a 3 minute test project in SD and burned it on a DVD disk. I was very pleased at the results and the ease of editing. I don’t have any HD tapes yet, but when I do what differences will I experience from shooting in HD and then capturing, editing, then to sharing? My current HD processes with the HF11 is slow, occasional low-resources warnings, and less then pleasing results on DVD disks. Thanks for any and all comments and/or suggestions.

Your HF11 is AVCHD format and the Canon XH A1 is HDV MPEG2. AVCHD takes a lot more computer horespower to edit compared to HDV MPEG2... main reason being that AVCHD is more highly compressed giving small file sizes. This is also why you get the low resource and memory alarms while editing.
To shoot HD you do not need HD miniDV tapes you can use the standard miniDV tapes. However the HD tapes are supposed to give fewer drop-outs than the standard tapes but are considerable more expensive. With DV-AVI a drop out would be hardly noticed, but as HDV MPEG2 is a compressed format and the picture relies on information in a number of frames any drop-outs can give a second or so of bad video. That said I have had very few issues with drop-outs. If you are doing a wedding or something important that you do not want to risk then probably better to use a HD miniDV tape.
In the past the advise has been to capture in high definition to get the best quality and then downconvert in the camcorder and capture in DV-AVI... the reason being that older versions of Premiere Elements did not do a good job of the down conversion. Reports on PE7 indicate it is better and that you could use a HDV workflow and burn to DVD as a last stage. This also allows you to export a high definition version of your video to view on a monitor where you can appreciate the higher resolution. Or in the future when you have a Blu-ray burner and player you can burn the file to disc... save doing all the editing all over.

Need to capture edited values ALV

Hi All,
Iam working with OOALV and I need to capture the edited values of ALV.
Here Iam successful by capturing edited values in first time.
i.e, Execute the program edit on row then Save I able to capture the row in PAI and I save it in dbtab and again come to alv screen and now I will edit some other row . But, this time Iam unable to capture the edited row.
Here I used check_changed_data method to capture..
Pls help me in this regard.....
Thanks,

>
> i.e, Execute the program edit on row then Save I able to capture the row in PAI and I save it in dbtab and again come to alv screen and now I will edit some other row . But, this time Iam unable to capture the edited row.
>
> Here I used check_changed_data method to capture..
are you using REFRESH_DISPLAY method.
in the data_changed after the population.
And where you are calling that method
if it is in PAI , in the beginning then that would be fine. You need to use the REFRESH_DISPLAY after the update and you need to call the FLUSH method

Launch and edit problem from Dreamweaver to Fireworks

> This message is in MIME format. Since your mail reader
does not understand
this format, some or all of this message may not be legible.
--B_3266405159_588474
Content-type: text/plain;
charset="ISO-8859-1"
Content-transfer-encoding: 8bit
Hi
Not sure if this is a Fireworks or Dreamweaver problem but
here goes.
I¹ve created a graphic in Fireworks CS3 on the Mac and
Exported the HTML and
related images. I open the HTML file in Dreamweaver CS3, all
fine so far.
Then I highlight the table and click the Edit in
Fireworks¹ button and it
throws up a warning dialogue saying Cannot launch and
edit. The Fireworks
table could not be found in the HTML. Please export from
Fireworks and
re-import the HTML into Dreamweaver.¹
What?!!
I¹ve only just exported it from Fireworks! It¹s
even got the Fireworks table
code in the Code section, so what¹s going here?
Has anyone else had this?
Gaz
--B_3266405159_588474
Content-type: text/html;
charset="ISO-8859-1"
Content-transfer-encoding: quoted-printable
<HTML>
<HEAD>
<TITLE>Launch and edit problem from Dreamweaver to
Fireworks</TITLE>
</HEAD>
<BODY>
Hi<BR=
>
Not sure if this is a Fireworks or Dreamweaver problem but
here goes. 
I’ve created a graphic in Fireworks CS3 on the Mac
and Exported the H=
TML and related images. I open the HTML file in Dreamweaver
CS3, all fine so=
far. Then I highlight the table and click the
‘Edit in Fireworks&#821=
7; button and it throws up a warning dialogue saying
‘Cannot launch an=
d edit. The Fireworks table could not be found in the HTML.
Please export fr=
om Fireworks and re-import the HTML into
Dreamweaver.’ 
What?!! 
I’ve only just exported it from Fireworks!
It’s even got the Fi=
reworks table code in the Code section, so what’s
going here? 
 
Has anyone else had this? 
 
Gaz
</BODY>
</HTML>
--B_3266405159_588474--

> This message is in MIME format. Since your mail reader
does not understand
this format, some or all of this message may not be legible.
--B_3266407908_747577
Content-type: text/plain;
charset="ISO-8859-1"
Content-transfer-encoding: 8bit
When you export the sliced graphics from Fireworks it places
them into a
table. In my instance the code says...

So it recognises Fireworks was the the graphics app and jumps
back to it
when you want to edit the image. Fireworks then displays (or
should) a
Done¹ button over the window. You do your alts and
press Done to update the
HTML and graphics back in Dreamweaver automatically.
That¹s the only table I was referring to Murray.
On 4/7/07 3:02 pm, in article
[email protected], "Murray
*ACE*" <[email protected]> wrote:
> Why would you be wanting to edit the table in a graphics
editor, instead of
> an HTML editor?
--B_3266407908_747577
Content-type: text/html;
charset="ISO-8859-1"
Content-transfer-encoding: quoted-printable
<HTML>
<HEAD>
<TITLE>Re: Launch and edit problem from Dreamweaver to
Fireworks</TITLE>
</HEAD>
<BODY>
When =
you export the sliced graphics from Fireworks it places them
into a table. I=
n my instance the code says... 
 
 
 
So it recognises Fireworks was the the graphics app and jumps
back to it wh=
en you want to edit the image. Fireworks then displays (or
should) a ‘=
Done’ button over the window. You do your alts and
press Done to updat=
e the HTML and graphics back in Dreamweaver
automatically. 
That’s the only table I was referring to
Murray. 
 
On 4/7/07 3:02 pm, in article
[email protected], "Murr=
ay *ACE*"
<[email protected]> wrote: 
 
> Why would you be
wanting to edit the table in a =
graphics editor, instead of 
> an HTML editor? 

</BODY>
</HTML>
--B_3266407908_747577--

Premiere Pro 7.1 serious Multicam Editing problems

Hello, I am posting here because the bug report I filed one week ago to Adobe didn't give a result -no response at all from the bug department.
I have two serious Multicam Editing Problems.
PC Configuration: Core i7950, Asus P6TD Deluxe, 12GB DDR3 1600MHZ, Quadro K4000, SSD for the system, Seagate Constellation 7200rpm for video editing.
1. When multicam mode is on at the program monitor, I press play and the program doesn't respond at all. The timeline plays till the end and the program just doesn't let you do anything but wait until playback of the whole timeline is over. Then the program works again (no "not responding" message in Windows).
2. Sometimes the waveform doesn't even appear at the multicam audio clip. I read in other forums that this problem is found specifically at Premiere Pro version 7.1 (October release).
I would be grateful with your help.
Thank you,
Stavros Symeonidis

The media is always a combination of HD .MOV (dSLR footage and .MTS (from my Sony Vg-30). However, I also tested it with .mpeg files created by "match sequence settings". GPU acceleration is always on, as I use nVidia Quadro K4000 with the latest drivers (331.82).
I always create the multicam sequences manually and the problem occurs with any amount of camera angles.
The problem was not solved by reinstaling Windows (7 and 8). In general, I have no other issue with my PC system, except from this specific one.
It doesn't appear always, however it will definitely happen if you press twice or three times the letter L, to fast forward the preview of your Multicam Sequence.
I remind you that this only happens when multicam monitor is toggled at the program monitor.
Did all these help at all to even reproduce this situation?
Thank you,
Stavros Symeonidis

FC studio2 editing problems with western digital my book home for mac

hi--bought a 1TB WD my book home for mac coupla years ago because it seemed like a good deal for so much space, and provided and eSATA hookup, too. Worked ok for a while. Now, with a growing Motion project that I bring into FC for overall color/levels/export adjustments, I'm getting a long-term beachball every time I try to do anything with it. Just did a complete reinstall of FC studio (after running Techtool pro 5 rebuild and optimizing files and volume), trashed the project and recreated it incase the file itself was corrupted, but the beachball keeps showing up once i try to get past a particular edit and play the file through -- something I haven't had problems with before. Have read this harddrive is a real POS/PIA for many because of its internal "sleep" setting and other weaknesses, and am thinking of cracking the drive out of its case and putting it into a plain eSATA/FireWire enclosure. Anybody else tried this or heard of it working? Money's a big issue right now (too many slow/no pay clients), so can't just run out and get a new drive and transfer w/out trying cheaper route first. Would appreciate feedback, cuz this is makin' me lose what little hair i got left!
Message was edited by: jayvee56
Message was edited by: jayvee56

My question says: "Final Cut Studio 2 editing problems"; I formatted the drive for the mac when i bought it: journaled HFS+, Apple Partition Map; 2 partitions (and connected via eSATA); which has been working fine as is up till now. The sequence and settings are those in which I've worked on many projects for years with no problems up until now. I am also completely up-to-date with all my app and system updates. I did begin to wonder after posting if the reinstall might be the source of my problems, but it was the interminable beachball waits that prompted the reinstall in the first place.

CS5 DV capture/playback problems "Feel like I am hitting my head on a wall"

Ok, I am still trying to get our commercial production editor working as intended so our creative services person can make the full switch to the new machine. Right now he is half editing on his 7 year old Pinnacle Liquid system that is dying. My fear is a Hard drive will fail again in that old thing and he won't be ready to fully edit on this New system...
Up till now in my other posts I have had issues with Playback and capture problems with a Blackmagic SDI card. Not sure if it is incompatibility with my motherboard or lack of support from Blackmagic but playback was dropping frames if we used GPU acceleration. We also had the problems of pixel shift when doing dissolves on the timeline that are documented on Creative Cow as an ongoing problem that Blackmagic seems unwilling to fix. Also had problems with long format captures....
My system is currently as follows:
Asus P6T7 Supercomputer
i7-950 CPU
12 GB memory tripple channel
500 GB 7200 RPM boot drive
3 1 TB drives in a Raid 5 (2 TB usable space) for scratch (originally had 4 1 TB in Raid 0, one died and is out for warranty)
Out of frustration with the blackmagic card, and the fact that we are only editing to/from DVCAM SD, I decided to pull the card and go to a simple FireWire setup as that is what our newsrooms use to DSR-11 and DSR-25 decks.
Because This editor uses a DSR-1800 full size deck and was always tied to the Pinnacle via SDI/AES, I wanted to stay in that format. This was why I chose the Decklink SDI in the first place.
I picked up a used Firewire card for the DSR-1800. ($299 off of e-bay, originally a $1500 card)
I figured if this worked I could sell the Decklink SDI and be about even.
Now with the Decklink uninstalled and the firewire card connected, we are having new problems...
The capture from DV works as normal, but when you hit stop on a capture there is a very long delay.. 20 seconds to 3-5 minutes before premiere will pop up the "name this clip"... this does not happen on the DSR-11/25 decks in news.(they are much slower AMD Phenome II systems with 4 GB memory)
When I playback to the DSR-1800, it takes the deck 10-20 seconds to switch back to the iLink input. He switches the deck back and forth to other inputs for dub over from DVD and when he edits on the Liquid system. once it switches it plays fine....
Has anyone have experience editing from a DSR-1800 over firewire? I knew the option was there but have no experience using this setup.
I don't have any idea what would cause the major delay from the time we hit stop on a capture. No frames are dropped in the capture window and everything else seems to be working fine. We are not using deck control just clicking record and play on the deck and then stopping the capture when we are done.
The other problem, I wanted him to be able to use the $1600 Quadro 4800 video card so all renders would be quick and he would not have to wait like he did on the liquid system (everything rendered...)
The blackmagic Decklink SDI would drop frames playing out SD-SDI. I know SD-SDI is uncompressed format and I guess the issue could be just not enough disk speed to feed that output or there is a bottleneck in the PCIe buss. But now I found that DV does not allow GPU either, so he can't play the timeline with the GPU acceleration on at all. What a waste of $1600 on that video card if he can never use it!!!!!!
So as you can see I feel stuck. Can't seem to get any answers from Adobe or Blackmagic. now the budget has been slashed for this year and there is probably no chance I can try new hardware on anything...
At this point I may switch back to the Decklink card and add another hard drive to put the windows page file on. Harm has said load balancing across the system will speed things up.
My OS disk is much slower as a single 500 GB than the raid 0 was when I used the disk speed test. Sorry for such a long post but more information should help people know all I am dealing with..
Thank you,
Mark

Darren, I did run that test when we were using the 4TB Raid 0 for Scratch. The raid was much faster than the boot drive. I also found that he had some files on the C: drive. He has a Share on there with Photo's and logo's he works on in Photoshop.
I am wondering if I should have two Raids. One Raid 0 with two 250 GB drives for Boot, and then Raid 5 for the other three 1TB drives giving a 2 TB Scratch. That way there is some redundancy for scratch material. Only problem with that plan is if either Raid0 drive fails I lose the OS/installation...
Probably follow Harm's Drive setup advice and put the OS on 1 drive and have the Raid 5 for the others but move the Page file to either another spare drive or the Raid 5 array.
I also think his Media Cache is in the default space(hidden in common files under the user on the C: drive) knowing that is all the conforming audio files and such, it is probably causing the dropped frames when playing through the SDI out with GPU acceleration. GPU off and rendering always worked other than the shift of a frame when doing dissolves.
I think that with optimising the services through Win7 and turning off anything we don't need.
We are on a Domain and that automatically installs the Enterprise Antivirus. Does that cause problems? Also he runs as a user, should running as an Admin be a must? The main reason it is on the Domain is so he can have his e-mail accessible but that is not a big issue. What do you recommend?
I can remove from the Domain and have this a stand alone machine if that will allow me to turn off more stuff, and stop the anti-virus from running realtime scanning. Is there an antivirus you recommend? I usually like AVG free or Avast, and with these you can turn off the realtime and only have them run while at night when the system is not being used.

Editing problems

I am capturing slides from a web site; I have encountered a problem with broken lines appearing from a previous screen shot. The lines follow for about 4 - 6 slides then disappear. What causes this overlay of lines? The lines won't show on the actual slides when editing but only during preview. This has happen several times.

I found my answer in a previous post initiated by HRHall on Oct 2007. I located the problem in the MORE LIKE THIS link located at the top right of the forums screen.
The correct resolution was provided by CatBandit Oct 2007; I cut and pasted the below quote from CatBandit:
QUOTE: Watch the whole preview, making note of which slides you see the problem. Following the preview, go to the first slide on which you are seeing the "lines or dashes" in preview, and open the slide Properties **dialog.
**You can open the slide properties by right-clicking the slide and selecting Properties from the context menu, or you can select (highlight) the slide in the filmstrip, then click the "Properties" tool and the main toolbar.
In slide Properties, open the drop-list for "Video Quality", and change it to a higher (or sometimes lower) setting. The possible settings include "Standard", "Optimized", "JPEG", and "High", with "High" being the highest quality setting, or the one displaying the most colors. UNQUOTE
I followed the above directions and changed my affected slides from "High" to "Optimized" and it worked perfect.

DAC: Change capture sql problem.

Hi,
DAC 10g, SEBL_VERT_80
This is for vanilla code. When I right Click S_OPTY-> Select Change Capture Scripts->Generate Change capture SQL -> Incremental
I am getting the
Select * from Dual
It suppose to generate all truncate image table and create view script right. Whats wrong with the Configuration
Please help.
Suresh

Thanks Srini,
Sorry we have patched all our environments with following patch.
Dac Build AN 10.1.3.4.1.patch.20110427.0538, Build date: April 27 2011.
If i have to apply the new patch. i have to do it in all environments.
Its working in all other environments except one having problem.
Anyway I have re-installed DAC and it fixed the problem. I dont know what caused this problem.
Its shame that i have to re-install it, this is not recommended, this is not best practice.
Regards
Suresh
Edited by: slella on 04-Mar-2013 08:26

Capture edited film to FCPX

I have a few edited films on dv tape and I want to capture them to fcpx as a film. when I tried it appeared as separeted clips. is it possible or is there any other software to do that.
thank you.
Yinon

Did you also find that FCP X arranged the clips as they were chronologically shot thus jumbling up the films.
Frequently when you edit you use clips in a non-chronological order.
I had this problem which rendered my films useless.
The only solution I found was to import the films into Final Cut Express or FCP versions 1 to 7.
Any "old" editing app should be able to do the job.
On the other hand assuming that all the clips in the film are used chronologically, the fact that they are split will not cause any problem.

CMP and capture-schema problems

I am trying to deploy a CMP on Sun App Server 8, and I'm having a few problems. I am quite new to both CMP and Sun App Server 8.
I've created a simple table Room in mySQL DB, containing only id (varchar) and description (varchar). I'm running this command to capture the table schema
capture-schema -username username -password pwd -dburl jdbc:mysql://localhost/test -driver com.mysql.jdbc.Driver -out test.dbschema
Do I need to enter the -schemaname and -table parameters as well? I'm assuming that since the url is pointing directly to the test schema in mySQL and it only contains the room table, I don't need these 2 parameters.
test.dbschema gets generated, but when I use the deployment tool and create the database mappings to the entity bean using this schema file, no mappings are created.
Any help?

Hello,
I have similar problem and I'm really confused about it.
Working with:
Java System Application Server Platform Edition 8.1 2005Q1 UR1
mysql DataSource and Container Managed Persistence
mysql-connector-java-3.0.8-stable-bin.jar
I have problem with deploy:
Fatal Error from EJB Compiler -- JDO74025: JDOCodeGenerator: Caught an Exception validating CMP bean 'Sets' in application 'isvl' module 'isvl-EJBModule': JDO72335: If the table sets for the bean corresponding to the generated class isvl.model.set.SetBean470758938_JDOState is mapped as the primary table, it must have a primary key.Choose a different primary table or verify that the contents of the schema file are correct.
Choose a different primary table or verify that the contents of the schema file are correct. at com.sun.ejb.codegen.CmpCompiler.compile(CmpCompiler.java:274) at com.sun.ejb.codegen.IASEJBC.doCompile(IASEJBC.java:615) at com.sun.ejb.codegen.IASEJBC.ejbc(IASEJBC.java:563) at com.sun.enterprise.deployment.backend.EJBCompiler.preDeployApp(EJBCompiler.java :340) at com.sun.enterprise.deployment.backend.EJBCompiler.compile(EJBCompiler.java:209) at com.sun.enterprise.deployment.backend.AppDeployer.runEJBC(AppDeployer.java:284) at com.sun.enterprise.deployment.backend.AppDeployer.deploy(AppDeployer.java:176) at com.sun.enterprise.deployment.backend.AppDeployer.doRequestFinish(AppDeployer.j ava:107) at com.sun.enterprise.deployment.phasing.J2EECPhase.runPhase(J2EECPhase.java:146) at com.sun.enterprise.deployment.phasing.DeploymentPhase.executePhase(DeploymentPh ase.java:71) at com.sun.enterprise.deployment.phasing.PEDeploymentService.executePhases(PEDeplo ymentService.java:633) at com.sun.enterprise.deployment.phasing.PEDeploymentService.deploy(PEDeploymentSe rvice.java:188) at com.sun.enterprise.deployment.phasing.PEDeploymentService.deploy(PEDeploymentSe rvice.java:520) at com.sun.enterprise.management.deploy.DeployThread.deploy(DeployThread.java:143) at com.sun.enterprise.management.deploy.DeployThread.run(DeployThread.java:172)
Have you seen this problem?
Thanks.

Log and capture big problem

I am using FCP 3 (fully registered) i hit the log and capture NOW feature, and the screen brightness drops in half and a message that says I have to restart my computer and freezes up my computer. The message is in 4 different languages making me think that it may be a computer error rather than a FCP message.
I deleted my FCP plist file, and the FCP user data, preference file and the POA cache file. Problem is still there.

That's a kernel panic - whole system stalling.
Do you have both FCP 7 and FCP X installed?
If so, did you follow installation instructions provided by Apple:
http://support.apple.com/kb/HT4722

Editing problems with iTunes 64-bit in Vista

Hello!
Just bot a new computer with Win Vista 64-bit and had to install new iTunes 64-bit.
It's somewhat slow when switching between Windows and iTunes.
Also, what happened to the "quick" edit feature?
As in.... highlight song, hit F2 or just click ONCE with left mouse button and you can EDIT the song title, artist, etc...
It's NO longer available!
What happened to it?
I'm RE-importing my HUGE collection of playlists and backed up library and songs, which is all MESSED up and.... I have to spend TONS of time now EDITING the title info!!!
Anyone have problems or any solutions to this "editing" snafu????
Thank you!

Responding to own post.... Found answer!
Must set permissions!
Highlight iTunes folder..
Right click..
Properties..
Securities tab...
Click on EVERY group/user names..
Allow..
Full control..
OK!
Saved!
Darn Windows Vista!
Screwing up the file/folder permissions due to the hated UAC feature!

HD capture & edit problem

Similar Messages

Maybe you are looking for