HD Led not working with SATA drives on MSI K7N2 Delta

I noticed the HD led does not work with the SATA drives on my MSI K7N2 Delta ISLR
I confirmed that the led is not burnt out by reconnecting a spare IDE HD with XP on it to IDE 1 and the led worked when there was activity, but it does not work when connected to IDE3 or if the SATA drives are connected to Serial 1 & 2.
Could it be because the motherboard doesn't support and hdd led for the Promise SATA controller.
I had Bios v7.3 and flashed to v7.4 with no luck.
Could a new bios update fix this problem?
Anybody seen this before?

basically it not wired up so works for no one

Similar Messages

  • KT8 Neo.......Led Activity does not work with SATA drives

    Is this another MSI Flop.  
    Does anybody know if the HD led works when using SATA drives connected to the Via controller on the K8T Neo board?
    I checked the case led and it works fine.   It is not burnt out.
    I also have the K7N2 Delta board and the HD led does not work on that board either when using SATA hard drives.  I was told the led connecter was never wired to detect activity for the SATA drives only for IDE.  A bios upgrade would never fix it.
    I just setup K8T Neo and other than the HD Led not working the board seems to be pretty stable.

    The only led activity I get is when the board is first powered on and I just recently noticed when I play a DVD.  The led seems to flicker when the dvd is playing.
    Other than that I see no led activity with 1 or 2 SATA drives connected to the VIA controller.
    Can someone confirm that it either works or it doesn't work.    
    I keep reading all these posts and some say it works and some say it don't.  
    Unless their is a new revision of the KT8 Neo and everybody is connecting their led to the HDD Led pins on JFP1 (Page 2-19 in the manual) they all should either work or they all should not workl. From what I gather their is no new revision of the board and only one Bios v1.1.
    It also seems their was some confusion on what connector people were connecting thier led to on the motherboard.  From what I read on page 2-19 in the manual thier is only one choice on JFP1 (Top row, pins 1 & 3).

  • Hp pavilion 15 e025sl mute led not working with latest audio driver (rollback solve)

    Hi,
    i'm here for a segnalation, i have this hp and after update audio driver (suggested by hp update software) mute led stop working, the button work and mute the audio but led not work (f6 button led).
    Affected driver problem is "realtek high definition audio" version 6.0.1.7010, i opened hp recovery manager and restored driver 6.0.1.6856 after this, the led is back and working fine.
    Please, fix that problmem in the next update, for the moment i ignore request update for audio driver from hp support assistant.
    Thanks

    thank you for your response, I made this topic so that it may be useful to other users with the same problem, now I will contact the support hp.

  • JSP Not Working with Thin Driver

    My JSP is not working with Oracle thin driver but it is working with Oracle OCI driver.
    From my jsp i am calling a stored procedured and passing 170 parameters to the procedure. This JSP works with Oracle OCI Driver configured as thrid party drivers in iAS6.0 SP2, but not working with Oracle Thin Driver configured as third party drivers in iAS6.0. My thin driver JDBC Connection URL is as follows:
    jdbc:oracle:thin:@(DESCRIPTION =(ADDRESS_LIST =(ADDRESS = (PROTOCOL = TCP)(HOST = MAPDBI01)(PORT = 1521)))(CONNECT_DATA =(SID = MAPS))).
    I have to give this URL because my production server deployment consists of iWS4.1 SP5 and iAS6.0 SP2 in different solaris boxes and Oracle 8.1.7 Database server in another Solaris Box. There is a pool of proxy servers between iAS6.0 box and the oracle box.

    Wim,
    I'd really appreciate it if you could provide some sample code. A complete, small, simple java class that I could copy and try out would be wonderful -- if it's not too much trouble.
    Thanks heaps (in advance :-),
    Avi.

  • Line-in not working with new driv

    Has anyone else had issues with the line-in jack not working with new drivers? Is there a way to get it to work??Very frustrated. Is there a link to the beta drivers, they worked better for me then the new one.

    The line input on the mini requires a 'line-level' signal, so the only microphones that work are ones that have an amplified output. Standard mics don't generate enough voltage to drive the mini's amplifiers.
    That's the reason the mics work with the Griffin device (it has an amplifier) but not the mini directly.

  • Spdif out not working with latest drives on XFI

    /? I installed the newest drivers that were released recently. Driver version 6.0..347.
    Before I upgraded to these drivers my dolby digital was working fine.
    In powerdvd I have SPDIF/out selected. And the dolby digital light will not come on in the reciever. Anyone?
    else having this issue?
    SYSTEM SPECS: Antec P83 * Antec CP-850 * Intake two S-Flex SFF2E fans *
    Exhaust? two S-Flex SFF2E fan * Noctua NH-U2P SE366 cpu cooler * Asus P6T Deluxe *
    Bios version 605 * Core i7 920 @ 3.6ghz 20x 80bus * Mushkin 3x2GB 998679 @ 7-8-7-20 *
    Gigabyte 9800 GTX+ gig * PCIe SB X-Fi Titanium Fatality Pro * Pioneer SATA DVR-22DBK *
    Intel X25-M 60GB MLC SSD * Two Western Digital WD6400AAKS 640GB *
    ?Windows Vista 64 Ultimate SP2 not vlited
    Message Edited by galvin on 08-6-2009 05:08 [email protected]

    No one has this problem at all?
    I want to find out for sure if there is a fix before going back to the older drivers.
    If i do the test in the spdif out properties panel -> supported formats. When I do the dolby digital test I see the light come on in my receiver and hear sound just thru the front speakers. But when I use power DVD 9 ultra with the latest patch. I don't get the digital light on my receiver. I had this working with the previous drivers released earlier this year.
    Message Edited by galvin on 08-7-2009 0:54 [email protected]

  • G505s - Touchpad hot key function not working with lenovo driver

    I'm using windows 8.1, Lenovo G505s laptop. Recently I got replacement from Lenovo regarding touchpad after that this Fn(F7) touchpad enable/disable not working. This is happening only when I installied touchpad driver provided by lenovo and works well with standard microsoft driver (Ofcourse, no multigesture support with that driver).
    We perfomed following operations:
    1. HotKey mode enable/disable in BIOS
    2.Reinstallation of OS
    3. Reinstallation of driver(manually)
    All cases with microsoft driver this function working but with touchpad driver it is not working. It's almost 90days (88thday) daily contacting both Lenovo customer support and service center people but no use.
    If anybody having this problem and have a solution please share! (My machine under warranty!)

    hi phani_kumar,
    It's likely that you have a Synaptics driver (you can verify this by its hardware ID or use a utility software like AIDA 64 Extreme Edition).
    - Link to picture (Synaptics)
    - Link to picture (ELAN
    If you're unable to install the driver below, can you follow this guide on how to disable driver signature enforcement then try to reinstall the driver again and observe if you can now toggle the Fn+F6.
    Windows 8/7/XP/Vista 64/32-bit Edition v17.0.19
    All Languages
    118.1 MB zip
    Regards
    Did someone help you today? Press the star on the left to thank them with a Kudo!
    If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
    Follow @LenovoForums on Twitter!

  • Spotlight not working with External Drive (Wireless)

    I have setup the new Airport Extreme (AE) and connected WD 500GB via USB to the (AE). Spotlight does not recognize the external drive when it is connected to the AE. It will of course work if I directly attach external drive to my Macbook Pro. Any ideas on how to get Spotlight to "see" and index this external drive. Thanks.

    I was able to get my Airport disk working using the following Terminal command:
    sudo mdutil -i on /Volumes/Maxtor\ HD
    Replace Maxtor HD with the name of your HD. (The slash indicates a non-breaking space.)
    It took awhile and then it started indexing.
    J

  • Installing a single sata drive on a K7N2 Delta M/B

    where do I start?
    If I run the raid setup, it can see it fine in there right size and eveything, but can't see the drive (or any options for sata) in the bios, or anything relating to it in windows.
    Currently running XP with two IDE drives (no raid)
    Can I use the sata drive without using the raid?
    Does the sata drive have to be the primary drive?
    Many thanks
    Andy

    not sure if this is what yur lookin for but when i first got my raptor, i already had like a 200 gb and a 120 gb ide HD on my k7n2 delta2 plat, so i was like ok reformat time! since i didnt have that much stuff. i just disconnected my 2 ide drives, stuck in my 74gb raptor, and installed windows on that. but you have to be sure all the other drives are discconected while yur doin this. if u have other drives connected, it might now work, i got a boot disk failure at first! i was like lol lets do it again! but yea after i installed windows on the raptor, i just reformatted the other 2 hd's as dump drives. i hope this helps...in some way at least

  • Scanning Documents From File Center from HP Officejet Pro 6830 Not Working with Twain Driver

    I just purchased a HP Officejet Pro 6830 All-In-One printer and planned to use it to scan from Filecenter (Lucion Technologies) using TWAIN driver. The Twain driver for the HP shows up in Filecenter, but the scan produces a blank document. My previous All-In-One printer from Dell (Lexmark) scanned to this software with no issues. Are there any solutions to this issue?  Filecenter has different scan modes A and B and Transfer type (Native, Memory and File) and I tried all 6 options and none worked.

    Hi @cyclebob ,
    I have brought your issue to the attention of an appropriate team within HP. They will likely request information from you in order to look up your case details or product serial number. Please look for a private message from an identified HP contact. Additionally, keep in mind not to publically post ( serial numbers and case details).
    If you are unfamiliar with how the Forum's private message capability works, you can learn about that here.
    Regards,
    George
    I work for HP

  • Will iTunes 10.4 upgrade (Lion 64 bit ver) Not Work With External Drives Any More?

    Since i upgraded my MacBook Pro to Lion today, itunes just cannot play anything without going in to to meltdown. Even short tracks stop and stutter, and movies and TV programs are a no go.
    All I  get is the dreaded spinning beach ball.
    My library is stored on a Firewire 800 external drive as my collection would take up more than my MacBook can hold, but running from an external drive has never been a problem before.
    I know the library on the external drives okay, because I was streaming stuff over Airplay to my Apple TV2 half an hour before i did the upgrade, and it was working perfectly.
    Does anyone have any idea what this might be or causing it, or how I can rectify it please?
    Thank you

    Oh yes, I did that several times.
    Actually, I think i have found the answer. I think what was happening was that since this was a new iTunes version (and perhaps its moving from 32-bit to 64-bit type program) that it had to re-index it or catalogue it, or something in that vein anyway. I left iTunes open for a couple of hours and the external disk still attached and it now appears to have settled down, and i can report that its now working just fine.
    Phew!
    Thanks for your suggestion anyway.

  • ITunes 10 not working with external drive

    I am using iTunes 10 on my MacBook Pro..I wanted to move my library to an external drive due to its large size. I correctly created the folder in Advanced Preferences and "consolidated" my library. However, iTunes despite having the correct drive destination is stil looking at/for the old library. Any advice would be greatly appreciated.

    Did you move the entire iTunes folder or did you just move your media?
    If you moved the entire iTunes folder, the you need to hold down
    the option key when you start iTunes. I dialog box will come up
    asking to create a new library or to choose a library. Select the chose
    option, then select the location on the external drive where the iTunes Library
    file is located.
    If all you did was move the media, then you need to change the path to
    the media in the advanced preferences.

  • [nForce] msi k7n2delta ilsr hdd led not work

    hi guys, well there is not much to say only that my hdd led not work, rarely i put attention on it, but just when i see... is gone... sniiiff.. i tryed change the led, invert cables, and the raid controller has nothing to do with this issue, sometime ago i have power issues, and during those times the led suddenly "wake up" , then i change the psu, and hdd, now i have sata hdd, and somebody told me the led not work with the 3· ide or sata, culd be the data cable
    thanks

    "...yes yes i know that, right now using sata i know the hdd led not work, but when i-m using ide drive either, thas wy i saying may be the ide cable.thanks..." That's not what you said in your first post. IF IDE HDD works (even if HDD led doesn't work) then IDE cable should be OK. Perhaps HDD light case/mobo connection has a problem.

  • Recovery did not work with new hard drive

    The original Toshiba HD(250G, sata1) of my laptop( ) crashed.
    I bought new one (320G, sata 2, Western digit )
    The problem is that, when I tried to use the recovery CD that I used to use it with old HD before, it did not work with this new HD well!?
    After cd1 and cd2 finish installing it ask to take it out then restart, I do so, but when it comes to setup setting of windows.
    An error message come out says " Windows Setup could not configure Windows on this computer’s hardware”
    It restart and says again " Windows could not complete the installation. To install Windows on theis compuiter, restart the installation."
    I have been trying to solve this a lot, but no way
    I tried what in this link, but it drive me with another problem http://answers.microsoft.com/en-us/windows/forum/windows_7-windows_install/windows-could-not-complet...
    I hope that I get the right thing to do, from ur forum by this post.
    Thanks a lot

    Did you folks search here for "advanced format drive"?    People have had numerous weird problems with the new advanced format hard drives in older Toshibas.    I can't look up all the threads for you.    But here is one:
    http://forums.toshiba.com/t5/System-Recovery-and-Recovery/Recovery-won-t-work-on-new-upgraded-hardri...

  • I had a repair done on my MacBook Pro and had to have a new hard drive installed. The Apple Auth Repair Shop then updated the OS from 10.6.8 to 10.7.5. Now my iPhoto v 9.2.3 will not open and it sounds like it will not work with this OS. Can you plea

    I had a repair done on my MacBook Pro and had to have a new hard drive installed. The Apple Auth Repair Shop then updated the OS from 10.6.8 to 10.7.5. Now my iPhoto v 9.2.3 will not open and it sounds like it will not work with this OS. Can you please advise?

    You may need many other updates to retain compatibility with Lion. I suggest you reinstall Snow Leopard. Unfortunately, you will need to erase the drive first. Be sure to backup your data if you haven't done so already.
    Clean Install of Snow Leopard
    Be sure to make a backup first because the following procedure will erase
    the drive and everything on it.
         1. Boot the computer using the Snow Leopard Installer Disc or the Disc 1 that came
             with your computer.  Insert the disc into the optical drive and restart the computer.
             After the chime press and hold down the  "C" key.  Release the key when you see
             a small spinning gear appear below the dark gray Apple logo.
         2. After the installer loads select your language and click on the Continue
             button. When the menu bar appears select Disk Utility from the Utilities menu.
             After DU loads select the hard drive entry from the left side list (mfgr.'s ID and drive
             size.)  Click on the Partition tab in the DU main window.  Set the number of
             partitions to one (1) from the Partitions drop down menu, click on Options button
             and select GUID, click on OK, then set the format type to MacOS Extended
             (Journaled, if supported), then click on the Apply button.
         3. When the formatting has completed quit DU and return to the installer.  Proceed
             with the OS X installation and follow the directions included with the installer.
         4. When the installation has completed your computer will Restart into the Setup
             Assistant. After you finish Setup Assistant will complete the installation after which
             you will be running a fresh install of OS X.  You can now begin the update process
             by opening Software Update and installing all recommended updates to bring your
             installation current.
    Download and install Mac OS X 10.6.8 Update Combo v1.1.

Maybe you are looking for