HDD blinking red light

I have a pavilion dv4-1220us. I have noticed that from time to time the HHD starts spinning and the white/blue light turns amber and starts blinking slowing down the computer to the point that the only option left is to reboot. I cannot connect any action that might cause this to happen. Any ideas how to solve it?

>SOLVED: allready tried several cables, also with double usb (Y-cable).
>solution was a cable with a interferencefilter close to the HDD.
Thanks for feedback!

Similar Messages

After upgrade attempt for 8310, device will not restart -- only blinking red light

Problem: I tried to upgrade the device software to 4.5, and now THE DEVICE WILL NOT RESTART AT ALL. Not with a hard reset. Not using the SIM and battery from my 8310 and putting it in hers. Nothing. Just a red light that blinks in a pattern: two quick blinks, then a pause; two quick blinks, then a pause, etc.
Background: This 8310 had vers. 4.2.2 device software, and something like 2.6 on the desktop. I downloaded/upgraded to 4.6 for the desktop and 4.5 for the device from the AT&T site. The Desktop manager prompted me to install the new device software... looking good. After several minutes, I got an "unknown error" message and it stopped the install.Following a support article, I uninstalled reinstalled both updates, but then the problem occurred: no NOTHING happens on the device screen at all, just the blinking red light when the device is plugged in.
The AT&T store tells me this is about the tenth "dead" Curve he's seen in about a week, apparently all occurring when folks have attempted a software updgrade. Any thoughts/help to offer?
Please help!
Solved!
Go to Solution.

Check this instruction:
http://crackberry.com/blackberry-101-lecture-12-how-reload-operating-system-nuked-blackberry

HELP! Double blinking red light

I was in the middle of upgrading the software on my curve 8330, the software stopped doing anything, and now my phone is off and just has a double blinking red light.
I figure its now dead, but how can i fix this using my mac?
I see plenty of instructions on how to load a new OS using a PC, but none for a mac
Any help would be greatly appreciated!

Welcome to the forums
It seems you may have wiped the OS due to the accidental shut down. Try pulling your battery out and reinserting it to see if the phone boots up. If not, see how to restore a bricked blackberry: http://crackberry.com/blackberry-101-lecture-12-how-reload-operating-system-nuked-blackberry
If you have a recent backup, you can load it onto the phone once you are done.
Kijana
Please remember to:
1. Mark Accept as Solution on the appropriate post once your issue has been resolved
2. Give Kudos to helpful posts (click the star next to the post)
Thanks

Blinking red light while in docking base

What does this mean? I don't think it is charging because it will do this all night. Used to be just fine. I haven't been able to find any discussion around a slow blinking red light on the Shuffle...it flashes on and off at about .5 Hz
Ideas? Tried it on a bunch of computers and even a wall charger. Is the battery done? (At only 9 months!)

well, i sort of managed to get the shuffle to an apple authorized repair centre here in bangalore,india where they infact had the firmware updated to the latest and since the charge indicator was showing a red, the executive at the shop suggested that the unit was really low on charge and needed a minimum of 4 hours of charging. Upon charging the unit for more than 6 hours or so, the charging indicator still blinks red(when charging). i am able to play songs for the time-being but it seems the green light is totally conked out.
does anyone know of a repair shop of ipod shuffle in india. the apple dealer was saying its best to discard the shuffle when having problems like this since its best to go in for a new shuffle. i do have another shuffle that cant be repaired:(

I have a Samsung Network Extender, model SCS-2U01, and for the past two weeks, the SYS light has gone from solid blue to a blinking red light, disconnecting me from my business calls. In reading the forums, it was mentioned that Verizon had to reset somet

I have a Samsung Network Extender, model SCS-2U01, and for the past two weeks, the SYS light has gone from solid blue to a blinking red light, disconnecting me from my business calls. In reading the forums, it was mentioned that Verizon had to reset something on their end to fix the issue. Would you be able to confirm if something needs to be reset to fix the issue? Thank you!

First, try the normal stuff: power cycle your modem, router, and NE allowing time for each component to stabilize before turning on the next in sequence modem > router > NE. If necessary, try resetting your modem and router. If it still doesn’t work verify it is listed in MyVerizon and then calling Verizon Wireless Customer Service at (800) 922-0204. Good luck!

Playbook is dead with a blinking red light

My playbook went dead and does not come back even if I charge it for 24h.
If I push the start bottom a blinking red light come up. I try to re-boot it pushing all bottoms and does not work.
Also I have tried to dowload new software through my laptop but never complete it and get stuck in the middle.
Any idea anyone???
Thanks,

Many others have had this problem - first thing to do is check to make sure your are using the charger that came with your PlayBook. Also check the threads at the top of forum for oft-asked questions. For your convenience here is a link that might help. Good luck.
In the dark and need a sky map?
Discover What's up at App World.
Follow What's up on Facebook

Blinking red light of DEATH

Hi guys!
In advance, thanks for your help! So here is my problem and I hope you guys can help a young gal out! I dropped my blackberry and it hasn't worked since. It wont turn on but it will for a few minutes, then will randomly shut off and blink like 2 times in a row in perfect intervals. After it turns off... it will not come back on no matter what. I have tried a different charger and even bought a new battery to put in it... But nothing has changed. Its still the same red light! PLEASE help me... Is there anything I can do that I haven't tried, before taking it to a repair shop and spending a bunch of money for them to tell me they can't fix it?!
THANKS SO MUCH AGAIN!
---Alex <3

This may not work if the drop caused some physical damage, but normally for a black or white screen only, and/or the blinking red light:
1) Make sure you have Blackberry Desktop Manager installed.
http://na.blackberry.com/eng/services/desktop/
2) On your PC, go to Start > Run and copy and paste the following line exactly (meaning with the quotation marks):
"c:\program files\common files\research in motion\apploader\loader.exe" /nojvm
3) The Application Loader Wizard will appear -- click "Next."
4) In the "Connection:" drop-down menu, you should see "USB-PIN: UNKNOWN". Click the "Next" button.
5) You should then see a list of applications ready to be installed for your Blackberry. Hit Next and Finish and you are well on your way to getting your Blackberry back to life. Just don't disconnect anything and let the lengthy process finish completely.
NOTE: If you do not see a list of applications mentioned in step 5 and instead see the message "The Blackberry Desktop Software does not have Blackberry Device Software for the device that you have connected to the computer. Contact your wireless service provider or system administrator," then you must download Blackberry's Operating System for your carrier and device.
http://www.blackberryfaq.com/index.php/BlackBerry_Operating_System_Downloads
Just select the appropriate carrier and network type, select your Blackberry model from the list and download the latest version. Install this download and follow the above steps again and you should be on the right path.
1. If any post helps you please click the below the post(s) that helped you.
2. Please resolve your thread by marking the post "Solution?" which solved it for you!
3. Install free BlackBerry Protect today for backups of contacts and data.
4. Guide to Unlocking your BlackBerry & Unlock Codes
Join our BBM Channels (Beta)
BlackBerry Support Forums Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

Blackberry Curve 9220 Won't Switch stuck On only red light blinking RED LIGHT! HELP!

my blackberry is stuck on red light blinking oleas help me no problem if all the data is lost i dont care i want my phone back it hase been 3 -4 weeks . light is blinking until the battery goes down and it wont charge also i have to get the battery charged by other phone plzz help mee........

Hi and Welcome to the Community!
Please try this sequence...note that, throughout the entire 4h15m process, your BB must remain directly connected to a known-good wall charger (not PC USB, not a cradle):
With the battery inside, connect your BB to the wall charger
Leave it alone for 2 hours, no matter what the LED or the display does
Remove the battery
Wait 15 minutes
Insert the battery
Wait another 2 hours, no matter what the LED or the display does
This has been known to "kick start" some BBs.
It is also possible that your battery or BB has experienced a problem...to test, this sequence is needed:
Obtain an known good and already fully charged additional battery...use it in your BB and see what happens
Obtain access to a known good and identical BB...use your battery in it and see what happens
The results of this will indicate if it's your BB or your battery that has the problem. Note carefully please that "new" and "know good" are not necessarily the same things. While rare, a "new" battery certainly could be defective. Rather, the simplest (and least costly, btw) method to conduct this test is to find someone with an identical BB who has no issues...trade batteries and see what happens.
Good luck and let us know!
Occam's Razor nearly always applies when troubleshooting technology issues!
If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
Join our BBM Channels
BSCF General Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

Photosmart 7450 appears to be jammed, blinking red light

My Photosmart 7450 had been working great until a few weeks ago. It just stopped printing. I didn't change any settings or cartridges. I've tried unplugging everything, cleaning it out, changing cartridges, test prints...
Symptoms:
- When I turn it on the light is green and appears to be functional (Good)
- When I tell it to print it feeds the paper into the proper position (Good)
- The print cartridges start moving (Good)
- Red light comes on blinking and everything stops (Bad)
- When I open the lid the cartridge is on the right side, and when I try and move it by hand it is stuck by a little tab below it
Any thoughts what it might be and how I can fix it? Thanks.

What modem do you have? Is it a pure modem.. ie no router??
If it is a router then the Express has to be in bridge mode.
Assuming you have a pure cable modem..
When you change from the computer to the Airport Express, are you powering down the modem. If it has battery backup for phone you need to remove the battery as well.. it has to be off for around 20min but it can be longer or shorter than that. Restart the modem.. wait a couple of min then plug in the Express which must be in router mode so it captures the public IP.

Blackberry 9790 blinking red light

Good day people, pls I really really need ur help badly...my 9790 suddenly tripped off when I was using it this afternoon, and since then the red light has been blinking and d phone hasn't been booting.
I connected the phone to PC, it wasn't recognised, downloaded mcp but I don't know how to use the software. Would be glad if I can get some explanation on how to use it or if I can get another way to go about it

Hello!
Please try this sequence...note that, throughout the entire 4h15m process, your BB must remain connected to a known-good wall charger (not PC USB):
With the battery inside, connect your BB to the wall charger
Leave it alone for 2 hours, no matter what the LED or the display does
Remove the battery
Wait 15 minutes
Insert the battery
Wait another 2 hours, no matter what the LED or the display does
This has been known to "kick start" some BBs.
It is also possible that your battery or BB has experienced a problem...to test, this sequence is needed:
Obtain an known good and already fully charged additional battery...use it in your BB and see what happens
Obtain access to a known good and identical BB...use your battery in it and see what happens
The results of this will indicate if it's your BB or your battery that has the problem.
Good luck and let us know!
Occam's Razor nearly always applies when troubleshooting technology issues!
If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
Join our BBM Channels
BSCF General Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

Blinking Red Light

Greetings,
I'm missing messages because when I receive a message, the red light blinks for only a minutes or two. Can I change it to blink until I check it?
Thanks,
Shane.
Z10 STL100-3 (version 10.3.1.2708)
LTE Playbook (version 2.1.0.1917)

rat-7 wrote:
keithbergoff wrote:
If no one else has a suggestion, backup, reload OS and restore.
Keith you are wrong, the LED will blink only for about 15 minutes unless the messages have been checked before, after about 15 minutes the LED stop blinking to save battery life
It has been like that since 10.0, and it is the same for the Z30 as well
I could be wrong, I use CascaRun app that keeps the display on permanently (45 to 75min), during that time the LED has not stopped blinking when I receive a message. Other times I have never seen an unread message in the HUB when the LED was not blinking.
S.Goodman also mentioned a minute or 2, not 15 min.

Blinking Red Light s and start

I have tried for a week now, charging for 24hours with the provided charger but it will not boot. It just blinks with 2 red lights every 5 seconds or so.
I tried puching teh start button for 20 seconds...nothing, also tried puching all the buttons for 20 seconds...nothing.
Help!?

Any Help...?

Blinking red light wont go off

When I receive a message in the middle of the night and check my phone in the morning, the red light will continue to blink even after reading any messages and deleting them. The only way the I have found to get the light to go out is to turn the phone off, of send myself a message and open it right away. I have tried rebooting the phone numerous times and it continues to do the same thing.

I had this same problem
Try downloading LED reset application. I can't remember for sure where I found it, I think it was on crackberry.com If not you could try searching google.
>>>>>>>>>>>>>>>>>>>>>>>>~
Hope I was able to help
If you have received information that has helped you out, please give them Kudos.
If your problem has been solved, please click on the post that resolved the issue

Blinking red light and wont connect to bb desktop?! ! !

i tried the video by hotnoob on youtube..and advice as well on here..
maybe im doing something wrong..
ive held the button(s) ,,
if i could just get it to sync with desktop id be fine
please help thanks!

Read the technical support pages for your router model. There is an article on the blinking power light somewhere. It describes in detail how to load a new firmware to the router using tftp. Try this procedure.
If it fails try to do what I have posted here.

8330 screen is dark & get blinking red light (4blinks)

My 8330 screen is dark and I get flashing or blinking red signal. I have tried pulling the battery to reset and does not help. Can anyone offer any suggestions?
Thanks,
JRW8
Solved!
Go to Solution.

You need to load the operating system software to your PC, first... before you can install it to your device.
Good luck, post back here if needed. Those instructions will work. Follow them exactly as written.
1. If any post helps you please click the below the post(s) that helped you.
2. Please resolve your thread by marking the post "Solution?" which solved it for you!
3. Install free BlackBerry Protect today for backups of contacts and data.
4. Guide to Unlocking your BlackBerry & Unlock Codes
Join our BBM Channels (Beta)
BlackBerry Support Forums Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

HDD blinking red light

Similar Messages

Maybe you are looking for