Header qty is less than the operation qty.

To certain production order header qty is less than the operation qty. Please advise me.

Dear,
Base Quantity - Quantity of the material to be produced to which the standard values of the operation refer.
Operation Quantity - Quantity planned for this operation.
Base quantity and operation quantity may not always be the same, if we have partial lots delivered during the sequence of operations, the operation quantity will be equal to the lot delivered during the operation.
Base quantity is dependent on the BOM, where it signifies the total quantity of output after using the components of certain quantity.
In routing, you neeed maintained there operation quantity, and unit of measure of operation quantity accordingly with base quantity unit of measure.
Check up the Processing formula used in the Scheduling tab of Work center (Use SAP002 = Machine * Oprn qty / Base qty / No. of splits)
Hope clear to you.
Regards,
R.Brahmankar
Edited by: R Brahmankar on Oct 7, 2008 11:37 AM

Similar Messages

Issud qty is greter than the   Reservation qty

Dears,
I   Have creted the   Resevation 100 qty for cost center 1.
While i am    issuing the   qty    to   cost center system is allowing more qty than the reserved   qty100.
Even if i given the 200 qty system is posting the Document .
How Avoid this Posting and where i ahve   to    cofigure the    System   setting please Guide   Me.
If i am   issuing the   More qty than the   Reserved qty systemm should give the   Error message.
Like issued qty is more than the   Reserved    qty .

This can be controlled by setting the messages to Error in the Relevant application area.
Go to SPRO-MM-Inv Mgmt & Phy Inv-Define attributes for System messages / use trxn code OMCQ and find the Relevant message number and set to Error and Save.
Also Check in SPRO-MM-Purchasing-Environment-Define attributes for System messages / use trxn code OMC0 (trxn code may not work) and find the Relevant message number and set to Error and Save.
Eg : 06 078 Target quantity exceeded by & & etc

Qty received less than Purchase UoM Qty

Forum,
Anyone ever run into an issue when a Vendor sends a quantity of a product that is less than the purchase UoM Quantity?
Example:
Purchase UoM = Case
Qty per Unit = 720
We created a Po for Qty = 1 (720 units)
The Vendor only shipped 300 units.
How can the users easily create a GRPO for only 300 units.
Tried setting Qty to 300/720 = .416667
But this causes a decimal issue and an issue with having partial quantities in the system.
Anyone experience this before and have a solution?
Thanks in advance,
Brad Windecker

Brad,
One thing you could do....
On the PO..Enable Base Units column using the Form Settings.....The Base Units column is a drop down..change it to Yes
This will ignore the UoM setting in the Item Master and changes your PO quantity setting to eaches (1) and price for 1 quantity.
Now change the quantity to 300. Duplicate the row and change the quantity of the second row to 420.
This way you can receive the first row when copying to GRPO while keeping the PO balance quantity of 420 intact
Suda

GR qty less than the SL qty.

Hi Experts,
I have 2 schedule lines scheduled for earlier dates.
say, SL-1 -> 100, SL-2 -> 200
If i do a GR (MIGO) against the SA today then it should prompt me the qty as 300.
But the system is prompting a lesser qty (say 50). Why??
What all do i need to check to resolve this...
This is very urgent.. please advise...
Thanks,
Manju

Hi,
Since the SL dates are in the past, if i do a GR at the present date then it must allow me to receive the entire qty (i.e. 300 in this case).
But, it is not allowing me to receive qty more than what it has proposed.
I need to receive the entire qty that is due.
Please advise.
Thanks,
Manju

Returns qty accepting more than the invoice qty

Hi Experts
When i am creating a sales order with reference to invoice the system is allowing to enter the quantity more than the invoiced quantity.
suppose the invoice quantity is 100 when i create a sales returns system is accepting to do returns for 150 also whichshould not be and also it is allowing to do so many times with the same reference document
i am getting just q warning message that for this invoice reference already returns exists if i bypass the warning message system is allowing to do next time also
how to do
any user exits to control which checks the VBRK number and VBRK billed quantity and it should less or equal to VBAK quantity
regards

Hi,
Yes, unfortunately SAP does allow it.
We are using FORM USEREXIT_MOVE_FIELD_TO_VBKD of MV45AFZZ to have our own validation for the same.
I hope this helps,
Regards
Raju Chitale.

Schedule target qty is less than schedule line qty.....

hi,
please tell me can i avoid users to not to give schedule line qty more than target qty.....
is it possible.....

Hi friend,
yes it can be possible.....
there is a message for it,it may be a warning in your case.... just turn it to error,
Go to spro--->Material management>Purchasing->Environment data--->define message systems...
Go here select your message....it may be some thing like M06xx
select the message and turn it to error......
Now while the user will crete a schedule line in Me38 he will not be able to create schedule line ....
Hope it is usefull.....

Service PR qty reduced than the PO qty

Hi,
For material PR, if the qty is reduced than the PO qty we can activate
06 648-Requisition quantity already ordered in full (see follow-on docs.)
but what is the message no for service PR line item control.(if the service PR qty is reduced than the Service PO qty)- for service line item.
we are not using the service master for for creation of service PR/PO

dear indranil,
thank you.
06 076 is applicable for material PO, it is not working for service PO.
as header line qty and not the service line qty
we have already checked the same.

Increased Qty in sales order than the Billed qty.. urgent

Hi folks,
When I am creating a return sales doc. with reference to a Billing doc,
everything is getting copied on to the return sales doc.
The Qty of the item is also getting copied on to the sales doc.
But when i increase the qty of the item , it is giving me a warning message saying " Qty is more than the billed qty." and thus allowing me to take it.
The client want that this should be an error message and hence shouldnot allowed to take the increased qty.
Can anyone tell how to make it an error message.
thanx
sourav

Hi Sourav,
Check copy control settings in the transaction VTAF.
In that you go to item level copy control check the field Pos./neg.quantity whether this field set as '-' or not.
If not set enter - (Minus) then try
If already enter you need to go for the User exits to cahnge the warning message to error message.
I hope it will help you
Regards,
Murali.

GR qty showing less than production order confirmation qty

Hello Experts,
Greetings.
My issue is while doing production order confirmation(CO12),for some materials it shows less GR quantity than the confirmation qty.I m wondering how it can be possible?
What could be the problem?
Plz advice.
Thanks
Nitin

Confirmed qty of each operation and delivery qty at the header are two different fields. Confirmed qty will be the same with the yield to conf. during confirmation. Whereas, the GR qty is equal to the total sum of quantity received from the order.
Check whether during confirmation you create auto GR or not. If yes, then check the COGI t-code. There might be some error log of goods receipt in there. If no, then check GR qty in document goods movement compared to confirmed qty during confirmation.
Hope it helps.

Message-4F181 :Credit Quantity less than Excise invoice Qty

HI,
I have done migo with part 1 entery,WHLE DOING J1IEX .I AM GETTING A WARNNING MESSAGE 4F181 :Credit Quantity less than Excise invoice Qty
Please suggest
Regards
SAM

Hii,
Did u reduce the Quantity of the Excise Invoice??
Regards,
Kumar

How to use parallel sequence for split the operation qty. urgent or other o

PP guru
My scenario is as follows.
I ve one material supposexyz.
For that material I' ve created bom, routing.
In routing I' ve mention only one operation. 0010.
Now I' ve the production order of 1000 kg.
I want to use two work centers to run this production order. ( e.g.work center a and b)
In routing I used work center a.
In short I want split that operation.
So what I ve to do or use parallel sequence and how???
or else is there any other option to split the order to two or more machines/work center?
Pls explain me in brief.
Regards,
Ram

Hi,
If you want to carry the production with two different work centers , first you need to split the operation qty.
For this in the order type dependent parameters OPL8
in the controlling tab page enable the indicator Cost collector
and set the default rule as PP2.
Create a Product cost collector with KKF6N.
   Now in the production order , select the operation and choose functions--->>> split.
   Now enter the operation split quantity and execute.
   Now in MD04 you can see two production order.
   In the second production order change the work center in the operation overview as desired and save.
Regards,
nandha

Excise invoice quantity cannot be less than the quantity received

Hi,
I have done MIGO with part 1 entry but while doing J1IEX, I am getting an error message 4F109 : Excise invoice quantity cannot be less than the quantity received.
Please note that we have done MIGO with 5000 qty. and doing J1IEX with short 3000 qty.
Regards.

Hi,
For this case of "Part I" selected during GR, you need to create Excise invoice thro J1IEX -> Capture Excise Invoice -> Good receipt (use the material document number), which will complete the part II posting. Then you can proceed with MIRO.
With regards,
Jeeva.

Create TO for a quantity less than the delivery quantity

If we have created an inbound delivery in MB1C, 561 movement to post an initial entry of stocks, and then packed the HU in Vl32N. Now, we want to create a TO for a quantity less than the delivery quantity.
In LT03 I cant see any option to change the TO quantity. How can we actually change the TO quantity to be less than the Delivery quantity.
Thanks
-Mike

Mike,
I dont think that's going to be possible. The TO gets data from the del qty which is in your embedded HU since you have packed the qty in the del in the HU,
so if you are trying to create a TO with less qty means that you want a qty less that the HU in the del and this is not possible.
Alternatively :
1) You can receive it in your warehouse.
2) Move it in a re-packaging area
3) break the HU and re-create a new HU.
4) Pack the desired qty
5) Move the 2 HU's back to their desired bins.
Hope this helps and works!
thanks'

The amount of down payment must be less than the invoice amount

Hi all,
Our customers are using SAP 2007-PL15 and SAP 2007-PL41.
When we want to create a down payment for a sales order, and we want to pay the entire amount of the sales order, including tax, we have to put an amount inthe TOTAL field of the Down Payment window since by default, the down payment amount is the total of the invoice before applying tax. The DPM is
higher than 100% (strange but I think it's normal since the down payment is not planned to take the tax in consideration).
Then, we create an incoming payment for this down payment. It's ok.
Then, we create an invoice based on the sales order we have paid with the down payment. It's impossible to use the down payment for the invoice... why that ? We receive the error 'The amount of down payment must be less than the invoice amount'. This causes big headaches to our customers !!
Could you explain us what to do please ?
thanks,
Luce

I'm very sorry, I have a similar question in dealing with AP Down Payment Request Linked to AP Invoice, my case like this:
1. I created 3 AP DPRs,their amount are each 100,000 RMB(for example, their document number are 10,11,12). then do the outgoing payment fully paided.
2. I created a AP Invoice with the amount 150,000 RMB(for example, this AR Invoice document number is 5). I use the buttom"Total Down Payment",and selecet AP DRP No.10 and 11. When I click the buttom"Add",an error shows:
The amount of down payment must be less than the invoice amount
and I don't know how to continue.....
Many Thanks
Kam
(PS:My English is poor,forgive me please. Shall I Speak in Chinese? then I can describe this question more clearly.)

Messages in Xi is less than the messages in R/3 server after processing.

Hi Experts
I have a scenario file - Idoc.
XI picks up the file from FTP process it and sends to the R/3 server.
Now I have a problem is when I check the Data in XI using IDX5 or SXMB_MONI the no of messages in xi is less than the messages in R/3 server.
I am checking the data of the last day like 8th May from 00:00:00 to 23:59:59 in both the cases.
In R/3 I check using BD87 t code.
Thanx

Hi Divyesh
Thanks for your prompt reply.
Ya I am also doing exactly the same . But the problem is that I am checking for yesterday datas.
In idx5 I get total of 2625 messages for orders.
When I check the same on BD87 i get 2636 messages with status 53 & 1 message with status 51.
Difference is of 11.
Now the question in how is it possible that it is picking 2625 data from FTP and after processing its sending 2637 data on R/3 server.
Thanx

Header qty is less than the operation qty.

Similar Messages

Maybe you are looking for