Heating problem with HP TouchSmart 600-1050sc

Hi There..
Got this recurring problem on my HP TouchSmart 600-1050sc. (No changes made to org. config)
Every time i open more then 2 browser windows, or set up more than one game client, the cooling fan goes into a frenzy. ;o(
On my old stationary computer, I would rip the computer apart, and clean all cooling modules with cuetips and a small wacuumcleaner to bring down overheating, but on this mashine it's not the obvious task. (Well seems like it would be a humongous job)
Anyone have experienced same problems, and have a clever solution ?
Kind regards,  Agger

Hi Ashik_ch,
Welcome to the HP Support Forums, I hope you enjoy your experience! To help you get the most out of the HP Forums I would like to direct your attention to the HP Forums Guide First Time Here? Learn How to Post and More.
I see that you are concerned over the heat coming off your Envy. 60 degrees isn't overly hot for a CPU but here is an HP support document on Reducing Heat Inside the PC to Prevent Overheating. It will show you how to clean out the inside of your notebook.
Thank you,
Please click “Accept as Solution ” if you feel my post solved your issue.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Thank you,
BHK6
I work on behalf of HP

Similar Messages

  • Memory modules not working on HP Touchsmart 600-1050sc desktop - update BIOS ?

    Hi
    I just bought 2 x 4GB DDR3 PC3 12800 memory modules from Cruical (see http://eu.crucial.com/eur/en/touchsmart-600-1050sc/CT5311446)
    The modules does not work on my HP Touchsmart 600-1050 sc desktop. Acc to HP specs it should support 2 x 4GB (max 8 GB in total).
    But the computer does not start (I have installed the modules correct). The manufacturer advises me to update my BIOS.
    I wanna ask you guys, before I try suhc a thing, is there any chance this could help?
    Thanks

    Hi,
    Its specs:
    Memory upgrade information
    Dual channel memory architecture
    Two DDR3 SO-DIMMs (200-pin) sockets
    SO-DIMM type-PC3-10600 (DDR3-1333)
    Non-ECC memory only, unbuffered
    Supports 2 GB DDR3 SO-DIMMs
    Maximum memory only if using 2GB DDR3 DIMM modules.
    Supports up to 8 GB on 64-bit PCs
    Supports up to 4 GB* on 32-bit PCs
    Please try PC-10600 RAM
    Regards,
    BH
    **Click the KUDOS thumb up on the left to say 'Thanks'**
    Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

  • Due to the rumored heat problems with the iPad 3, is there a danger in using a leather case design for it.

    I recently purchased a 64 GB Verizon LTE iPad,  along with a Bear Motion leather case designed specifically for that model. I've been reading a lot about the heat problems with the new iPad and although I haven't noticed them on mine, I'm worried that putting it in the case may cause worse problems. Is this something I should be concerned about?

    Unless you have a defective iPad you should be fine.  The only time it should be heating up is when you're running an intensive app like a game that's working the quad-core processor and the screen.  I bought a Targus leather case for mine and play InfinityBlade2 on it and haven't noticed any heating issues with mine, but the part holding the iPad is plastic, so it can disipate heat better.
    If your iPad gets too hot it'll warn you, so I'd use it for now and see what happens.  It'll shut down before it causes any permanent damage.

  • I have a problem with the touchsmart 420pc, after a running time (2 hour approx) is turned off,

    good afternoon, I have a problem with the touchsmart 420pc, after a running time (2 hour approx) is turned off, probably warming, but this rare, is suddenly going slow parapadear and image.
    also sounds like when damaged ballasts for lamps,
    ANYONE know what could be the cuasa and / or what is causing this.
    greetings and thanks in advance

    Hi,
    Please write your TouchSmart model number, which system are you using and country of purchase.
    Resource:
    How Do I Find My Model Number?
    ** Say thanks by clicking the "Thumb up" icon which is on the left. **
    ** Make it easier for other people to find solutions, by marking my answer with "Accept as Solution" if it solves your issue. **

  • Problems with HP TouchSmart 300 and Itunes - not transferring to iphone 4s or the new ipad

    Hi
    I've got problems with trying to transfer music to my iphone 4s or new ipad with itunes on this computer.  It will only transfer some songs....and what it does transfer is not complete i.e. starts 10 seconds in etc.  It doesn't do this with our ipods, which are both new.  Music transfers fine onto them.  We never had this problem with our old acer laptop.
    It also does this with photos, but I bought a camera connector for that problem.  This Touchsmart has always been a bit jittery with itunes, but still worked after for playing music music after launching task manager, and opening again.  This does not rememdy this issue.  I read a while back that people suggested completely removing itunes (and all it's components such as bonjour etc, but I'm not sure how to do this)and re-installing it all again.
    I believe this is a HP issue with software compatability with itunes and the 4s and ipad.  If anyone could help - that'd be appreciated, as it's driving me mad!!
    Thanks

    Hello funcdoc:
             I just got back from speaking with my friend. He said that only mp3 files can be loaded into your Iphone. Yes you can use the windows media center as I mentioned above post in case Itunes software still isn't working for you. I asked him about that also. He will be here on Thursday some time after 3:00 p.m. Eastern Standard Time. To give you direction on how to load music mp3 from Itunes into your I phone as well. He is going to give you the links for downloading other music websites like you tube. He said you need this software as well. He is a casher was working to night it was to busy for him to write all this all down for you. He has college classes he goes during the day and works at night. He has been doing this since he was 11 years old. Like you he is in to his music.
           I hated it when he would use my computers because all the malware he use to put on my computers and the Itune always updateing pop up would always display. Then he would mess up my settings. This time my computer has software that can delete and fix up his mess he makes. So just relax for now if need be we can go live chat with any messengers you like to use Skype will allow you to view my computer screen. He is an expert using Apple's software.  You have already updated your computer software solution 25 has the one for fix USB and other ports issue you desribe in your second post . You have a fresh copy of Itunes installed so that covers every thing. If he isn't to busy in the store tomorrow I will see if he can write down some of the direction for you. He will be here for sure on Thursday for sure just for you.  Ok. Remember only mp3 music files can be uploaded unto I phones. frrw

  • Heating problems with U160

    Hi all,
       I just got  a Ideapad U160 and it arrived yesterday. I liked all the features and looks but the system is getting hot pretty fast. The left side vent started blowing hot air within 10 mins of it being on. The entire left side gets hot which does not allow me to put it on my lap. I was using it for regular browsing with balanced power setting on.
    Is this normal for this model? I hope it is not as I think this could be the best light/small/reasonably high performance laptop running windows.
    To test it, I just left it idle for 5 mins after turning it on, but the problem is the same.
    My configuration: Core i5 - 470m running Win 7 home premium
    Please post your experiences/advise.
    Thank you.

    according to this thread, maximum temperature is 67 degrees celsius at the processor.

  • Heating Problem with K8N?

    Hi first time post here!
    I'm planning on purchasing the K8N for the Athlon 3000+.  However, looking at the "Post High CPU Temperature" thread, I was a bit concerned of the temperatures.  
    1)  Are the temperatures listed on that thread typical or isolated cases?
    2)  What are ideal CPU temperatures?

    hi spaz (from ocforums) and philly
    i hope i can answer your questions fully...
    the k8n neo platinum is misreading high temps for newcastle cpus.  the readings are thought to be as much as 20°C too high.  lots of people are running at "60-70" under load, but NO one is reporting problems from high temps.. this apparently is very common in newly released motherboards..
    everyone gets around 45°C for the "sys temp" in MSI's corecenter utility.  personally, i don't anything drastic is going on here... maybe it's misreadings, maybe it's a natural temp for this mobo, maybe a BIOS version will bring down the number... i'm just going to trust MSI's decision to release this board and say that there's nothing to worry about with the sys temp readings.

  • Heating Problem with G500s

    I got the Lenovo G500s yesterday and it was working very well at home. When I got it in the office and fired up Second Life, the wristrest area has heated up. Is that normal? If not, what is the solution? I am sure it it sill in warranty. I got it yesterday.

    Hi Roydsilva,
    Welcome to Lenovo Community!
    I’m sorry to hear that your G500s Laptop getting heated up at the palm rest, please let me know if the Laptop is heated up before or after turning it ON.
    Hope to hear back soon
    Best Regards
    Shiva Kumar
    Did someone help you today? Press the star on the left to thank them with a Kudo!
    If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
    Follow @LenovoForums on Twitter!

  • Heating problem with g62

    my hp g62-361tx notebook gets heat up at the lower left size after half an hour usage is it normal or i hve to consult hp about this

    Download and install the following file:
    ftp://ftp.hp.com/pub/softpaq/sp52001-52500/sp52459.exe
    first download the file to the desktop then install
    Do not interept your PC when installation is in progress
    ||-Although I am working on behalf of HP, I am speaking for myself and not for HP.-||
    //Click on Kudos if my reply was helpful and answered your question//
    ||-If my answer solved the problem please mark the topic as the accepted solution-||

  • I am having start up problems with my touchsmart 300, the pc powers up but screen remains black

    I tried disconnecting all cables including power cable and holding power button for 30 secs and then restarting but the problem persists.  The fan starts up but the screen does not and the pc makes no beeps.  Any advice on how to get it going?

    Hello Ric66: What's is holding start button 30 sec stuff. Stop doing that does nothing but destroys computer. It is not a diesel truck. Just turn on computer press and hold f8 key. Now you are in save mode move your arrow keys select save mode with networking. Now open up HP Assisant click maintain then click on tune up and check mark everything and enabled microsoft defragmeter and run it. I had you open it in safe mode with networking in case you needed futher assistant. Perform this task it is not a bad Ideal to scan your computer for malware and viruses. Now llet tune complete close all open windows and restart computer. If for some unkown reason the computer does not start up normal. Then press F8 again safe mode this time you are going to perform a back date recovery open up recovery choose restore to earlier point of time. Yes there is a short waiting period between Windows 7 and logon screen with black screen it is normal. That your start up is corrupted and defragmeter will take care of it. That is why you should scheduled PC tune ups.

  • Remote no longer works with HP TouchSmart 600 after Windows 8.1 Upgrade

    I upgraded to Windows 8.1 only to find my remote control no longer works.  Nor do the volume controls built into the side of the TouchSmart computer work after the upgrade. 
    The keyboard based volume controls have continued to work after the upgrade.
    Any solutions?
    This question was solved.
    View Solution.

    HI Dirko99:
    Welcome to the HP  forum!
    Thank you for your query.  I am pleased to assist you to the best of my ability!
    I understand that after upgrading to Windows 8.1, your remote control does not work, or the volume control built into the side of the computer. HP does not have updated drivers for Windows 8.1 and your computer. Downloading or Updating Software and Drivers for HP Computers. You could try the built in troubleshooter, to aid in resolving issues.  Follow these steps to run the troubleshooter:
    a. Press Windows key + C on your keyboard to show the Charms bar.
    b. Type Troubleshooting and click Troubleshooting under Settings.
    c. Now type Hardware Troubleshooter in the Search option.
    d. Click on Hardware troubleshooter to run the troubleshooter.
    Please let me know the outcome.
    Sparkles1
    I work on behalf of HP
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos, Thumbs Up" on the bottom right to say “Thanks” for helping!

  • Heat problem with Windows 7 64 bit

    Hi, does anyone face the same problem as me?
    Whenever I run my Macbook in Windows 7 (64-bit), it becomes very warm (warmer as compared to Snow Leopard!).. the fan doesn't seem to work at the right speed to cool down the system...
    Is there any software that I can install in Windows 7 to control the fan speed?
    Thanks a lot!

    I have the same problem, the fans don't as fast. I use SMC fan control on Snow Leopard (http://www.eidac.de/?p=134). I have a setting that I created for windows that runs the fans at their max, which is about 6000 rpm. When you set it to something like that and restart it will keep those fan settings going when you start Windows. It keeps it MUCH cooler.

  • Heat problem with multiple display (retina Macbook)

    Hello.
    I'm using retina Macbook pro 15".
    It is totally fine when i'm using macbook by itself.
    However, the temperature and fan speed increase whenever I plug in displays.
    If I use just one display, the change is not noticeable, but if i plug another display, GPU die temperature goes up to 75 degree C and fan speed become 3000rpm (from istat dashboard).
    If I use 3 displays (one thunderbolt, one hdmi and one with hdmi to mini dp), fan runs around 4000rpm which is quite annoying.
    Of course, above testings are all done in idle state.
    Is it normal or need to be fixed?

    this is normal. When connecting more monitors, the GPU has to render more pixels, thus making it work harder, driving up the temps and triggering the fans to blow more air.

  • Heating problem from camera side

    as i remember i used to play games for at least 2hours continuously and there was no heating problem with my Lumia 720.but now i am getting some issues with that. Only after 5min of normal usage it is starting radiating heat which i can feel . What is causing it to get hot only after few min of usage.

    hmm. any device gets warm when you are playing games as it is stressing the processor and requiring more power usage. the amount of heat and power needed and created I have found to differentiate based on if GPS/data/camera are used a lot, where as others that are just resident on the device without connection don't seem to get as hot.

  • Does NVidia GeForce 8800GT have a heat problem?

    I have an older heavy-duty Mac Pro running with 8-core Intel 3.2Ghz Xeon processors and 18GBytes RAM, using an NVidia GeForce 8800GT display controller driving a 30' Apple Cinema display. After the Mac Pro has been on for half a day the white semitranslucent bars start to appear and gradually the screen goes to nearly all white if I leave it on long enough. In about an hour after I turn it off, the display is fine.
    What component is the likely cause of this behavior? I do not hear any fan noise. Should I?
    I have seen other reports of heat problems with temperatures and fan speeds mentioned. How do I find this out for the Mac Pro? MacOS verion is 10.6.3.

    Less than 80ºC (load) is desired, but up to 85ºC may be seen. A good cooler would keep the processor down in the mid 60's to mid 70's under load.
    Prolonged temps at and above the mid 90's will reduce component life.
    Certainly temps over 100ºC would be terminal in the long run.
    One would hope to see the card run between 50ºC at idle and no higher than the mid 80's under load.
    Lower load temps (mid 70's) are better.......
    The 8800 GT is getting old. Any card approaching or exceeding 5 years of use should have the thermal compound replaced.
    All fan equipped graphics cards need to be kept clean and dust free. A dust clogged heat exchanger is almost as bad as no cooler at all.

Maybe you are looking for