Hello Apple. Iphone6 ios8.0.2. I have problem with activation imsg and fctm. My number doesnt display on both apps. I can only use them with my apple ID. How can i fix this problem. Country:Azerbaijan. Number:  *********

Hello Apple. Iphone6 ios8.0.2. I have problem with activation imsg and fctm. My number doesnt display on both apps. I can only use them with my apple ID. How can i fix this problem. Country:Azerbaijan. Number:  *******
<Edited by Host>

Hello Khayalh,
You should be able to link your phone number by following the steps in the article below. From your iPhone, sign out of FaceTime and iMessage and then sign back in and it should link. Check in the Start Conversation With and I Can Be Reached at section in iMessage and FaceTime respectively. 
iOS and OS X: Link your phone number and Apple ID for use with FaceTime and iMessage
http://support.apple.com/kb/HT5538
Regards,
-Norm G. 

Similar Messages

  • My ipod recently cracked and now the right side of the touchscreen is not working. I can't even unlock the touch screen. How do I fix this problem if it even can be fixed?

    My ipod recently cracked and now the right side of the touchscreen is not working. I can't even unlock the touch screen. How do I fix this problem if it even can be fixed?

    You can pay to have it repaired.

  • When I take a picture with my iPhone 5s and afterward turn it laterally, the picture will not turn. It used to all the time. How do I fix this?

    When I take a picture with my iPhone 5s and afterward turn it laterally, the picture will not turn. It used to all the time. How do I fix this?

    Hi there dworthen,
    It sounds like you are experiencing issues when trying to rotate your display. I would recommend taking a look at the troubleshooting steps found in the article below.
    iOS: Screen does not rotate
    http://support.apple.com/kb/TS3805
    -Griff W.

  • Hello, my apple Id was deactivated due to un authorized perches. Now I can't update or down load anything. How do I fix this problem?

    Hi my apple ID was deactivated due to un authorizes perches. Now I can't update apps or down load.. How do I fix this problem?

    You need to talk to Apple
    http://www.apple.com/support/appleid/
    Contact support and see what they can do for you

  • HT4061 my memory is low on my ipad and i can not stay connected to the internet.  How do I fix this problem

    My ipad will not stay connected to the internet.  the message in the settings says low memory. How do I fix this problem?

    Go to Settings > General > Usage and you will see the memory consumers.  Remove some of the big stuff.

  • Ever since I downloaded FF's v6, everytime I go to YouTube and open a video, I get an error message that says: "[Java Script Application] Error: Div is null" How do I fix this problem?

    If I go to YouTube, no matter what video I click on to watch, the error message "[Java Script Application] Error: Div is null" pops up. It started happening right after I updated to FF v6. I also have installed the latest version of Java. I submitted this question a few weeks ago, but never received a reply.
    Thanks for any help you can provide to fix this.
    Scott Cromwell
    [email protected]

    hello, can you try to replicate this behaviour when you launch firefox in safe mode once? if not, maybe an addon is interfering here...
    [[Troubleshoot extensions, themes and hardware acceleration issues to solve common Firefox problems]]

  • The current version of Firefox moves the tabs. Now the focus moves off the end of the row. I think this runs counter to the point of having tabs, if you can only see one at a time. How do I fix this

    The tabs bar on 3.6 Firefox now focuses on the last tab in the row. This means that I can only effectively see one tab, unless I use the arrow button to scroll back through all the tabs. I am used to scrolling some, when there are a dozen tabs open, but How do I make the tab bar static, they way it used to be, so it stands still when I click on the last tab in the row.??

    Thanks for taking a stab at it: that didn't prove to be the problem. That option in the settings for tabbed browsing was not checked.
    I may be a bit behind the times: I am used to tabbed browsing showing all the tabs it possibly can, instead of just the last one. Sometimes it won't even show the last tab: I can have 15 tabs open, and not see a single tab. I've been confused by this into closing a window with lots of tabs open, because it looks like a single page-window.
    My main problem with the tab-bar flashing to the end of the row is that it means a great deal more mouse-clicking around to browse.
    I haven't tried installing the latest beta. Maybe that would fix the problem.
    Toddo

  • I can access my time capsule from my mac mini at work but my macbook can only access it from my home network. how do i fix this?

    I have a Mac Mini and a MacBook, both were configured at home to access the time capsule. I have since moved the mini to work to use there and it has no issues looking up files on the time capsule which remains at home. The macbook whoever can only access the time capsule from within the home network. I can't seem to find what I may have done differently. Can anybody help?
    Not sure if your allowed to post two questions, but it's may be related. I find that accessing the files on the time capsule from the mac mini or the macbook is very slow. Accessing the same files from an older HP laptop is as fast as accessing its own hard drive. How can I speed up the accessing of these files from my apple products. One would think they would work fast and the 'windows' computers would take minutes to map the drive each time... 
    Thanks for any help.

    I have since moved the mini to work to use there and it has no issues looking up files on the time capsule which remains at home.
    This cannot happen by magic though.. you must have configured the mini to access the TC remotely.. which method are you using, BTMM and iCloud??
    The macbook whoever can only access the time capsule from within the home network. I can't seem to find what I may have done differently. Can anybody help?
    How is the Macbook configured to access the TC remotely?? If you are trying to use BTMM and iCloud, then it might be a case that with the mini running the connection cannot be done by more than one computer at a time.. this is generally the case although I do not know if that is specifically true of BTMM method. Try turning off the mini and leave it off.. (off not standby)... then reboot the TC when you are at home.. and then try and connect the laptop to the TC the next morning from work. See if it is then able to capture the connection.. if so start up the mini and I suspect it now will not be able to connect.. that will prove that the TC cannot cope with two remote connections.
    There also could be another factor in here. If you are accessing the laptop via the same router as the mini is on.. then actually you cannot have two users mount the same files on a TC.. from the same IP address.. as far as the TC is concerned both devices have identical IP, that is the public IP of the work location router.
    If you happen to not be using BTMM then the situation is even easier.. you cannot make two different devices connect to the same network resource using the same port. That is the failing of the NAT system.. one device uses the port then it cannot be used by a second device. You will need to do some fancy footwork and use a different port.
    Anyhow tell us exactly how you are doing remote access.. otherwise I am just guessing.
    Not sure if your allowed to post two questions, but it's may be related. I find that accessing the files on the time capsule from the mac mini or the macbook is very slow.
    Are you talking about files you are hosting on the TC?? Not Time Machine backups??
    Can you tell me exactly how you are accessing the TC.. please do a test..
    Copy a file to the TC and from the TC using the Laptop.. Use a single very large file, eg 1GB movie file.
    Give me a read and write speed.. you can use activity monitor to give me an aprox average speed as well as peak.
    Do the same test from the same computer with wireless turned off running ethernet.
    Then do the tests from the mini.. same ones.. copy large file to and from the TC by ethernet and by wireless.. when using ethernet make sure wireless is off.
    I strongly recommend you set IPv6 to link local only for your wireless and ethernet setup in the Mac.
    eg
    Now do the test from the HP laptop and give me the results from that.
    Is the issue wireless only.. ??
    Then you might need to spend a bit of time fixing the wireless in the Macs.. you can run wireless diagnostics in Mavericks.
    About Wireless Diagnostics

  • I have a Thunderbolt iMac 27" with a Thunderbolt Display attached.  I would like to use the iMac and Thunderbolt display in Target Display Mode for my new Thunderbolt MacBook Pro.  So far, it seems I can only use the iMac screen itself.  How do I do this?

    When I press the Command + F2, the iMac screen becomes a secondary for the MacBook Pro, and the Thunderbolt Display becomes the primary screen for the iMac.  I was hoping that both screens would become secondaries for the MacBook Pro.  Does anyone know how I should proceed?  I have tried to connect the Thunderbolt display directly to the MacBook Pro, and the iMac to the Thunderbolt Display via the separate Thunderbolt cable, but there was no difference.  And since the MacBook Pro only has the one Thunderbolt port, I'm not sure how to proceed.

    Yes, eww, the language definitely states two thunderbolt displays, but I can understand the confusion and was siding with how they could make the mistake to think it would work like they want it to. My appologies for not being clear on that point, but I think you make it clear that the language in the ad says nothing about an imac.
    Having said that all the language about TB would suggest that this would be possible. http://www.apple.com/thunderbolt/
    High performance on display.
    Thunderbolt I/O technology provides native support for the Apple Thunderbolt Display and Mini DisplayPort displays. It also supports DisplayPort, DVI, HDMI, and VGA displays through the use of existing adapters. So you can connect your Apple LED Cinema Display or other display, along with multiple high-speed devices, all from a single port.

  • My doc is using a lot of memory.  how do i fix this problem

    i was playing aroung with my doc.  Adding and removing applications.  Now my doc is using all my memory. I dont know what I did?

    Restart your Mac.
    Captfred

  • My HP 1315xi All in One is recognized as a printer, but I can't use it's scanning features. How do I fix this?

    I have Mac OSX Mavericks installed. My printer is an HP PSC 1315xi (this is what's written on the printer) All in One printer/scanner. When I use it as a printer, it functions perfectly. When I attempt to use it as a scanner, however, it fails to work. If I press scan on the printer, the power light on the printer flashes, indicating, according to HP, a communication error. When I attempt to scan through image capture or preview, it tells me that there is no scanner detected, or simply disallows the ability to click the "import from scanner" button, depending on which I program I use. I have uninstalled and reinstalled the software a few times, but still have not reached a solution. On Apple's list of driver software, the 1310 series of HP PSC printers only has the print capability listed. Scan and Fax are not listed. This confuses me because my printer is a 1310 series, but is clearly a scanner. Is it just the case that I am unable to use my scanner as a scanner? If so, why? It's not a new scanner and it seems absurd that the software wouldn't exist which would allow me to use my HP scanner for the tasks it was built to perform. Apologies, I've been messing with it all day, and I'm frustrated with the whole situation.

    The list you saw that shows what drivers are available from Apple Software Update is based on what drivers are supplied by the vendor to Apple. So it would appear that HP has not provided Apple with a scanner driver for 10.9 (known as an ICA driver), or provided an update if one was available for a previous version of OS X, so that you can scan from Image Capture.
    I checked the HP web site for your model and they don't show any scanner driver or scanning software. If there was a scanner driver, you would be able to use Vuescan.
    As for the Scan button not working, the following is documented by HP
    Scanning to the computer from the printer control panel is not available when you scan with Preview, Image Capture, or Printer browser methods. You must use HP Scan software to scan from the printer.
    But there does not appear to be any version of HP Scan software available for 10.9. So unless someone else has some workaround, it seems that you won't be able to scan with this model of HP.

  • HT201303 I no longer live in Qatar. I am now living in Abu Dhabi. I have tried several times to update my account with new address and payment details but the system keeps telling me that I can only use a Qatari account?? How can I amend this please

    I have tried several attempts to update my account information as I have moved location and obvioulsy have new payment details.
    The system does not seem to accept the new information and keeps refering me back to my old details saying you cannot purchase in this area, we will put you back to the Qatari location???
    Please help, have tried now for 2 days to update

    Im trying to switch the Apple ID names around, and what i've learnt is that the Apple ID has to be an Email that isn't an Apple ID. Yup, it's messed alright.

  • Mozilla keeps crashing and i can only open it in safe mode. How do I fix this?

    I tried un-checking use hardware acceleration and tried to open but all it said was that i have to close mozilla because there is already a version running but hadnt even clicked on mozilla yet so i checked the box again and the crash report came back. I'm writing this in safe mode.

    If it does work in Safe-mode then disable all extensions and then try to find which is causing it by enabling one at a time until the problem reappears.
    *Use "Disable all add-ons" on the [[Safe mode]] start window to disable all extensions.
    * Close and restart Firefox after each change via "File > Exit" (Mac: "Firefox > Quit"; Linux: "File > Quit")
    In Firefox 4 and later [http://kb.mozillazine.org/Safe_mode Safe mode] disables extensions and disables hardware acceleration.
    *Tools > Options > Advanced > General > Browsing: "Use hardware acceleration when available"
    If disabling hardware acceleration works then check if there is an update available for your graphics display driver.

  • Since updating to iOS 8 my keyboard is blocking the area of text that I am writing on and will not allow me to scroll up. I am not using the split keyboard function. How do I fix this as it is quite annoying

    I Have recently updated to iOS8 and now my keyboard blocks the area of text that I am typing in an won't allow me to scroll the screen up to see what I am typing. I am not using the split keyboard function

    Hello there Smart43,
    It sounds like you are not able to correctly see the message you are typing because the keyboard is in the way. I can understand how that would be pretty frustrating. I would start by quitting the running apps on your device:
    iOS: Force an app to close
    Double-click the Home button.
    Swipe left or right until you have located the app you wish to close.
    Swipe the app up to close it.
    When you have done that restart the device and test the issue again:
    iOS: Turning off and on (restarting) and resetting
    Thank you for using Apple Support Communities.
    All the very best,
    Sterling

  • My I-cloud says I have no devices set up even when i'm logged in to my apple , how do I fix this problem? Please respond quickly, I lost my ipod and even when I try to place it in lost mode it still won't recognize that I have a device. What do I do?

    My I-cloud says I have no devices set up even when i'm logged in to my apple ID account, how do I fix this problem? Please respond quickly, I lost my I-pod and even when I try to place it in lost mode it still won't recognize that I have a device. What do I do?

    If you did not set up find my iPhone on the iPod, you can't find it.

Maybe you are looking for