Hello,good day problem with Cisco aironet 1040 series acces point

Hello good day to all, how to configure cisco aironet 1040 series using web configuration attaching through patch cord without using the console.
if possible please send me step by step instruction, any help is gladly appreciated.
thank you in advance, More power
mel

helo good day sir,
this is the first time i configure this device i am using Cisco aironet 1040 for our wireless using POE for power, and using cisco catalyst 2960 as switch
i jack the patch cord in and its goes on colored green,
the thing is how i can configure the aironet 1040  sir?
waiting for a step by step instruction,
thank you in advance
mel

Similar Messages

  • Cisco aironet 1200 Series access point dropping clients

    We are having an issue where our Cisco Aironet 1220 Series AP is constantly dropping clients. We have 3 APs mounted on a single tower, all out of each others range and freq. There are approximatly 30 clients on each AP. We are noticing an increase in dropped customers (up to 20 at a time). ANy suggestions? This only became an issue in the last few weeks, and nothing major has changed.

    Hi
    Even I was facing almost the same kind of problem. But in my case it was wired clients to the workgroup bridge 350.
    I had done lot of testings and reading at that time to resolve this problem.
    However in your case I feel your problem can be resolved by keeping the option "Reliable multicast for Workgroup bridges" disabled in the APs under dot11radio interface settings. This is possibly because the radios cannot associate to more than 20 clients at a time if the option is in the enable mode.
    You need to keep this option enabled in a root bridge when you have problems of dropping the wired clients to the workgroup bridge.
    By keeping this option enabled, you are actually asking the Root bridges to consider the Workgroup bridges as Infrastructure devices and not as clients thereby making the roots to send all the multicasts to the WGBs. However in that case it losses the efficiency of associating more than 20 clients.
    Let me know if this resolves your problem.
    Regards

  • Slow connection with Cisco Aironet 1040

    I have been racking my brain for a while and cannot figure out why I am not getting 144Mbps out of my Aironet 1040. I was reading a previous thread (
    https://supportforums.cisco.com/thread/2141961) and set it up exactly like it said. I have set the encryption to Cipher AES CCMP and set the SSID to open authentication. I also set the SSID's key management to enable WPA (WPAv2).
    I was reading that WMM has to be set. I have 3 options: Disabled, Legacy, and dot11d. If i chose dot11d I have to put in a coutry code. Problem is there are no options in the country code pull down. I cannot even manually type it in.
    Another problem is that cell phones cannot connect. It keeps saying authentication fails in the log.
    Any reason why I am having such slow speeds?

    WMM is enabled by default, or at least it should be.
    What type of client are you using?  Check the specs of the WNIC, and see how many spatial streams that it supports.
    HTH,
    Steve
    Please remember to rate useful posts, and mark questions as answered

  • Configuration of cisco aironet 1260 series access point..??

    i hv a cisco aironet 1262n access point and a normal router(without wlan)  with a broadband connection
    now i want to use my access point as a wifi hotspot 
    but i am not able to access it, through web browser
    i dont know how i connect wires so that i am able to access "  AP access page" and also i forgot its IP address too so can u pls tell me how do i reset it to default 

    Your AP is most likely loaded with a controller-based IOS.  You can easily convert this to autonomous IOS.
    Read this:  Using a TFTP Server to Return to a Previous Release

  • Cisco Aironet 1310 series

    hello all,
    I have a cisco Aironet 1310 series which am having problem with the signal strength. This box came with 8 dbi Omni antenna gain and am told this can go upto 5km raduis. After configuring this equipment, i could not get a link when i move 500 meters. Please find attached the configs on the box. Any help given would be very much appreciated. Thank You

    This 5KM distance is only going to be applicable in bridging situations. The following link shows how to use the distance calculations based on devices: http://www.cisco.com/en/US/products/hw/wireless/ps458/products_tech_note09186a008009459b.shtml
    In theory, if you had a really strong direction antenna on your client you'd be able to get the 1310 as an access Point from 5km, but you'd need perfect line-of-site and you wouldn't be mobile...
    As others had mentioned, if you're looking for an access point situation with that kind of range, then you need WiMax....
    but if it is bridging you want, its just a matter of getting the other link to see this one (with a good enough antenna)

  • Cisco Aironet 1100 series wireless access point software update!

    Hi,
    I have a wireless network using 2 cisco aironet 1100 series access points.
    From time to time I have problems with connecting a device (Laptop,PC,)to the wireless network.There are onther wireless netwotk that operate around and might be using the same channel.Someone else created the wireless network and I do not know how to access it now to check the configurations on change something.
    I cannot conncet my iPhone to the network and I beleive that a software update might solve the problem but I do not know how to do it and where to download it from.
    1. How can I update the software and where from?
    2.How can I ensure that thare are no interferences and conflicts?
    3.How can I ensure that no onther wireless network around is using the same channel?
    Thank you in advance.

    Sounds good to me. Are you having problems?
    Please remeber to rate all replies

  • Cisco Aironet 1300 Series Power

    Can the 1310ap receive it's power from a POE switch?

    Hi Edward,
    Sadly the 1310 cannot be powered by PoE ,but, the Power Injector can be up to 100 meters away from the unit.
    Dual coaxial cable to run from the power injector to the 1300. See attached notes:
    Cisco Aironet 1300 Series
    Cisco Aironet 1300 Series Access Point/Bridge Power Injector
    The Cisco Aironet 1300 Series Outdoor Access Point/Bridge Power Injector,converts the standard 10/100 BaseT Ethernet interface that is suitable for weather protected areas to a dual F-Type connector interface for coax cables that are more suitable for harsh outdoor environments. The Power Injector also provides power to the outdoor unit over the same cables with a power discover feature and surge protection. To support longer cable runs from your wireless network switch or router, the Power Injector LR is designed to accommodate up to a 100 meter coaxial cable run plus 100 meters of indoor cat5 cable?enabling total cable runs up to 200 meters. The Cisco Aironet 1300 Series Outdoor Access Point/Bridge ships with the Power Injector LR2 and an AC power supply.
    From this link:
    http://www.cisco.com/en/US/products/ps5861/products_data_sheet09186a008022551d.html
    Cisco Aironet 1300 Series Outdoor Access Point/Bridge Hardware Installation Guide
    Ethernet Ports
    The access point/bridge dual-coax Ethernet ports consists of a pair of 75-ohm F-type connectors, linking the unit to your 100BASE-T Ethernet LAN through the power injector. The dual-coax cables are used to send and receive Ethernet data and to supply inline 48-VDC power from the power injector to the access point/bridge.
    Power
    The access point/bridge receives inline power from the Cisco Aironet Power Injector (hereafter called the power injector). Dual-coax cables are used to provide Ethernet data and power from the power injector to the access point/bridge. The power injector is an external unit designed for operation in a sheltered environment, such as inside a building or vehicle. The power injector also functions as an Ethernet repeater by connecting to a Category 5 LAN backbone and using the dual-coax cable interface to the access point/bridge.
    AIR-PWRINJ-BLR2
    F-Type Connectors
    Dual coaxial cable carries full-duplex Ethernet, DC power, and full-duplex console port (RS-232 connection)
    From this link:
    http://www.cisco.com/en/US/products/ps5861/products_data_sheet09186a00802252e1.html
    Hope this helps!
    Rob

  • Server 2008 R2 RADIUS Server with a Cisco Aironet 1040 Wireless AP

    I am trying to get Server 2008 R2 RADIUS Server to work with a Cisco Aironet 1040 Wireless AP. I have installed the RADIUS server by MS standards and performed some searches on Google to configure the Cisco Aironet. I see others using a Wireless LAN Controller, which I do not have. I found this post below:
    https://supportforums.cisco.com/discussion/11546056/wlc-2504-radius-2008-r2-server
    But I have yet to locate a good step by step document on how to set it up and I have found so many different ways that others have set it up, but none have yet to work. I am having authentication issues that I have know of and I do not see any errors in the Windows Event Viewer and I do not know where the Acess Point stores it logs for any sort of error. Keep in mind this is the first time I am doing this. I do not have a Wireless LAN Controller and all my network / domain services are on individually built servers and not on one single server as I have seen with most of the documentation they all say the same thing by putting the Certificate Services, Domain Services (AD / ADS, etc), and NPS. I do not want that configuration and my setup should not be any different, but something is not right. I know from reading that this is not rocket science, but from someone who has never done it before this is difficult as I keep reading on and so many people do it different ways including what I have been reading according to what Cisco says to configure in the environment. Does anyone know where I can find good step by step documentation along with where I can look for logs on either device? I find that all the documentation I see on Cisco's website and from searching that it is old and outdated and not been updated in a long time so it is hard to determine what works and what does not work. I am stumped here and have been doing this for several weeks now with no luck. Thank you in advance.

    I did configure the Server 2008 R2 RADIUS Server using this video below: 
    https://www.youtube.com/watch?v=g-0MM_tK-Tk
    I also referenced Technet to make sure it was configured correctly as well. I am still not sure if I am 100% setup correctly on the Windows Server side, but I for sure want to make sure I have the AP side setup correctly. Do you know of a better article for the Windows Server 2008 R2 setup? Does it matter that I do not have all the services installed on the same server? Instead I have them installed on multiple servers.
    I have image number c1140-k9w7-tar.124.25d.JA1 on the AP. The part that confused me in that article, which I have seen before was the part about "Setting up access point must be configured in the authentication server as an AAA client." What is the AAA Client? I also am not aware of having Cisco Secure ACS anywhere built into the AP as that part through me off completely. Do I need to skip these steps? Thank you for help on this.

  • AP problem Cisco aironet 1040

    I have a Cisco aironet 1040.
    On my Accespoint i have 2 vlans: 1 for my wifi phones and 1 for my network.
    Wifi Lan has the SSID LAN with WPA enterprise authentication to a radius server(ms server 2008).
    Wifi Phone has SSID PHONE and vlan 50 with local radius authentication.
    This Works all fine, Except when i enable AP for my wifi phones.
    When AP is enabled the authentication for my lan doesn’t go to my server but local.
    How do I configure my accesspoints so that the cisco phones use the local radius server with AP and my windows computers connect using the ms radius server?
    Hope some one can help
    Attached is my current config.

    aaa group server radius rad_eap
    server auth-port 1645 acct-port 1646
    aaa group server radius WDS-AUTH
    server auth-port 1812 acct-port 1813
    aaa group server radius VOICE-AUTH
    server auth-port 1812 acct-port 1813
    aaa authentication login eap_methods group rad_eap
    Both of the SSID are calling to eap_methods.  What you need to do is configure another aaa authentication line:
    ** aaa authentication login phone_method group VOICE-AUTH**
    then call that as your network-eap:
    dot11 ssid VOICE
       vlan 50
       authentication network-eap **phone_method**
       authentication key-management cckm
    Change/add the lines between the **.
    HTH,
    Steve
    Please remember to rate useful posts, and mark questions as answered

  • How to change default admin password on Cisco Aironet 1040

    How do I change the default username and password on the Cisco Aironet 1040. There is a default set and I want to change that to secure the device. I've checked the manual and can't seem to find the directions. Any ideas?

    Hi Brian,
    If this AP is already registered with a WLC then you can change it via WLC.
    In WLC GUI, go to Wireless -> Select the AP -> Credential -> Override Global Credential-> Update username/pw/enable pw
    In WLC CLI, you can configure it like this. If it is for all APs, then select all, otherwise AP name.
    (WLC3) >config ap mgmtuser add username admin password Cisco123 secret Cisco123 ?
    all            Applies the configuration to every AP that does not have a specific user name.
         Enter the name of the Cisco AP.
    (WLC3) >config ap mgmtuser add username password secret
    (WLC3) >save config
    Are you sure you want to save? (y/n) y
    If it is Autonomous AP you can configure using the "username xxxx password xxx" IOS command
    HTH
    Rasika
    *** Pls rate all useful responses ****

  • NTP Service on Domain Controller have problem with cisco switch

    Hello!
    I  have Windows Server 2008 R2 SP1 Domain Controller with NTP services
    The windows opertion system clients get NTP time ok.
    There are problem with cisco switch, can't get time from NTP.
    Can anybody help me to fix problem?
    C:\Users\Sysuser>w32tm /query /configuration
    [Configuration]
    EventLogFlags: 2 (Local)
    AnnounceFlags: 5 (Local)
    TimeJumpAuditOffset: 28800 (Local)
    MinPollInterval: 6 (Local)
    MaxPollInterval: 10 (Local)
    MaxNegPhaseCorrection: 1800 (Local)
    MaxPosPhaseCorrection: 1800 (Local)
    MaxAllowedPhaseOffset: 300 (Local)
    FrequencyCorrectRate: 4 (Local)
    PollAdjustFactor: 5 (Local)
    LargePhaseOffset: 50000000 (Local)
    SpikeWatchPeriod: 900 (Local)
    LocalClockDispersion: 10 (Local)
    HoldPeriod: 5 (Local)
    PhaseCorrectRate: 7 (Local)
    UpdateInterval: 100 (Local)
    [TimeProviders]
    NtpClient (Local)
    DllName: C:\Windows\system32\w32time.dll (Local)
    Enabled: 1 (Local)
    InputProvider: 1 (Local)
    AllowNonstandardModeCombinations: 1 (Local)
    ResolvePeerBackoffMinutes: 15 (Policy)
    ResolvePeerBackoffMaxTimes: 7 (Policy)
    CompatibilityFlags: 2147483648 (Local)
    EventLogFlags: 0 (Policy)
    LargeSampleSkew: 3 (Local)
    SpecialPollInterval: 3600 (Policy)
    Type: NTP (Policy)
    NtpServer: 10.7.0.4 (Policy)
    NtpServer (Local)
    DllName: C:\Windows\system32\w32time.dll (Local)
    Enabled: 1 (Local)
    InputProvider: 0 (Local)
    AllowNonstandardModeCombinations: 1 (Local)
    VMICTimeProvider (Local)
    DllName: C:\Windows\System32\vmictimeprovider.dll (Local)
    Enabled: 1 (Local)
    InputProvider: 1 (Local)
    Cisco config and errors
    CISCO1#show ntp ass det
    10.7.0.7 configured, insane, invalid, stratum 3
    ref ID 10.7.0.4, time D5BC850F.C8400AB2 (15:50:39.782 MSK Mon Aug 19 2013)
    our mode client, peer mode server, our poll intvl 1024, peer poll intvl 1024
    root delay 62.50 msec, root disp 11128.04, reach 377, sync dist 11218.796
    delay 6.06 msec, offset -467951.1096 msec, dispersion 56.49
    precision 2**6, version 3
    org time D5BC8864.F79C33A7 (16:04:52.967 MSK Mon Aug 19 2013)
    rcv time D5BC8A38.EBDECB39 (16:12:40.921 MSK Mon Aug 19 2013)
    xmt time D5BC8A38.EA5173BE (16:12:40.915 MSK Mon Aug 19 2013)
    filtdelay =     6.06    5.87    3.23    7.90    6.41    5.17   13.03    3.43
    filtoffset = -467951 -467905 -467936 -467885 -467764 -467816 -467707 -467697
    filterror =     0.02   15.64   31.27   46.89   62.52   78.14   93.75   93.78

    Hi,
     >>I gave log on as a service right to this account in Default Domain Controllers Policy but unfortunately it was not enough
    Based on your description, we can try to grant this account Allow log on locally
    user right in the default domain controller policy to see if it helps.
    The policy setting is:
    Computer Configuration\Windows Settings\Security Settings\Local Policies\User Rights Assignment\Allow log on locally
    Allow log on locally
    http://technet.microsoft.com/en-us/library/cc756809(v=ws.10).aspx#feedback
    TechNet Subscriber Support
    If you are TechNet Subscription user and have any feedback on our support quality, please send your feedback here.
    Best regards,
    Frank Shen

  • Wireless site survey doubts with cisco aironet site survey utility tool

    Hi,
    I have 1131 autonomous AP and we have project where we need to implement WLC 5500 with 1140 LAP.
    Before that , we need to do site survey . we are going to use cisco aironet adapter and with the help of site survey utility tool we are planning to do site survey .
    I have below doubt before starting the site survey :
    1) do we need to configure the AP 1131 with existing LAN set-up of client to get connected ?
    If yes , how can i shift this 1131 ap always from one location to another location and connect to respective vlan in switch ?  It would be tedious job ....
    because , We need to connect ( get associated ) our laptop always to 1131 ap and then roam around to get the RSSI , signal strength , SNR and throughput ....  ...
    to configure the AP to existing lan set-up of client , it would not be flexible to do site survey ?
    without that , how can I just plug-in power to 1131 AP with standalone configuration .... and without connecting to switch ( any lan-port ) , do the site survey ?
    Please suggest me .............
    In short , without connecting to LAN set-up of client , how can i do the site survey ?
    2) will it be worth to do site survey with cisco aironet card ( site survey utility ) ? or we should i have different site survey software for the same ?
    Please share the knowledge .... 

    Site Surveys are important and should be done by a professional. A poor site survey can lead to a lot of problems. It would be hard to put all aspects of conducting a proper site survey in a single post. Lets cover a few of the basics.
    1) If you plan to deploy 1140 model access points. Then you should use that AP in autonomous mode so you dont have to be plugged into your network
    2) The AP gets powered by an exteral power source like this battery for exmaple:
    http://www.tessco.com/products/displayProductInfo.do?sku=345625&WT.mc_id=google_base&sp=true
    3) As far as moving the AP around you can purchase a site survey pole like this:
    http://www.tessco.com/products/displayProductInfo.do?sku=392506&eventPage=1
    4) As for software, I like AirMagnet Surveyor
    http://www.airmagnet.com/products/survey/
    But again. There is a lot to know about doing surveys...

  • Hello good day I can not install the trial version of adobe after Efectes

    hello good day I can not install the trial version of adobe after Efectes

    Hi Veritomeza,
    Which OS are you using? Also specify the version of After Effects you are trying to install along with the exact error message.
    Regards,
    Romit Sinha

  • TS1646 hello  I have problem with regist my visa and I cannot buy from store the message came in the end of form is says the phone number must be a 7-digit number and I have writed but not accepted iam from saudi arabia my mobile is 966504850992 pls answe

    hello 
    I have problem with regist my visa and I cannot buy from store
    the message came in the end of form is says
    the phone number must be a 7-digit number
    and I have writed but not accepted
    iam from saudi arabia
    my mobile is 966504850992
    pls answer
    thanks
    dfr aldossary

    Wow, Karan Taneja, you've just embarrassed yourself on a worldwide support forum.  Not only is your post ridiculous and completely inappropriate for a technical support forum, but it also shows your ignorance as to whom you think the audience is.  Apple is not here.  It's users, like you. 
    If you would have spent half the time actually reading the Terms of Use of this forum that YOU agreed to by signing up to post, as you did composing that usesless, inappropriate post, you (and the rest of us on this forum) would have been much better off.

  • Cisco aironet 2600 series AP configuration with windows 2008 R2 Radius server.

    I want to know the configuration of Cisco aironet 2600 series AP with windows 2008 R2 Radius server.  
    I have
    1. AD & DHCP Server
    2. Cisco Aironet 2600 Access Point.
    I want to connect wifi devices through this AP. Authentication should be through Radius server and AD.

    Hi , 
    Below link should support your requirement 
    http://www.cisco.com/c/en/us/support/docs/wireless-mobility/wireless-lan-wlan/116584-configure-wirelesslan-00.html
    Minimal command : -
    AP(config)# aaa new-model
     AP(config)# radius-server host 172.20.0.1 auth-port 1645 acct-port 1645 key XXXXXX
     AP(config)# radius-server deadtime 10
    HTH
    Sandy

Maybe you are looking for