Hello not working with network error - testing in Pacific Islands
A few of us in the Pacific Islands Internet Society have been trying out Firefox Hello. The experience reported is that on a local network (ie same provider in same country) it works fine but several of us report errors when trying to use it internationally. Most countries here are still reliant on satellite links. We all tried with our AV, Windows and any other firewalls turned off but still the same error:
"The stream was unable to connect due to a network error. Make sure your connection isn't blocked by a firewall"
Could this be latency or low bandwidth, or an ISP QoS issue?
For instance I am using only a 256/128 connection, in SOlomon Islands that is the most that is affordable (USD 450 per month). Is Hello only useable with high bandwidth? If so, it is not a Skype replacement.
Hi leemingd,
In order to further investigate the network error it may be necessary to gather logs:
In order to investigate if something went wrong we will need to collect more information:
#Open up about:webrtc in the url, start a conversation with a new link.
# Click on "start debug mode" and "start AEC logging" try to connect in the url, wait for the error then click on connection log.
#Use pastebin.mozilla.org to share the logs.
Similar Messages
-
Old computer not working with Network Magic
Hi I am having issues activating my license for Newtwork Magic on one of my home computers the desktop. I am using Network Magic Pro Ver. 5.1.9005.0-Pure 0 There are a total of 3 computers on the network. 2 are Dell Laptops with Home Vista. The third computer is a Dell desktop Precision 330. The desktop is running Windows XP Pro, Ver 2002 SP3, Pentium 4 1800MHZ. I have cable internet, Surfboard modem, a D-link router DIR-655. The desktop has a D-Link DWA-552 XtremeN adapter.
I have installed and un-install Network Magic 4 times but I still recieve the same message and yes i ran a clean disk, manually deleted files and restarted the computer everytime. The message I am receiving is: "The Licensing server could not be contacted. Please make sure you have internet connection and try again."
I am at this time using the desktop to send this message so yes I am connected to the internet but Network Magic is not acknowledging the connection. On my computer, a laptop, Network Magic indicates the desktop is on the network but a alert states that Network Magic is not installed.
Thank youBasics from the User Guide are restart, reset, restore from backup, restore as new device. Have you gone through ALL these steps? What exactly HAVE you done to troubleshoot your issue?
-
Hello, I have iMac Itel i3, from Oct, 2010 and have OS 10.6.7 and multiple users.
About 3-4 days ago the Mail icon in dock had question mark and was accidently removed, along with program on my user. Oops.
1. Mail 4.4 is on other users and works fine, but for me it does not work and tells me V4.3 does not work with latest OS X.
2. I reloaded software from my user with original disks (Oct, 2010) and got Mail 4.3 again. Mail 4.3 did not work with latest OS. I am unable to load Mail. Gives Yellow error message.
" You have Mail version 4.3 (1081/1084). It can’t be used on Mac OS X Version 10.6.7 (Build 10J869). For more information, click the Help button."
3. Tried to update software and look for update for mail 4.3 on Apple site to no success.
Hate to go to MS-Entorage ( I may need to learn something new and alien) mail program since contracts are in Mail/Address Book.
Ideas?
MattDeedsMatt,
I would download and run the 10.6.7 combo update.
http://support.apple.com/kb/DL1361
Regards,
Captfred -
Comcast Cable Internet not working with router (WRT54G), but network is fine?
My Comcast Cable Internet is not working with my router (WRT54G), but my home network is fine. The internet works without router.
I have a WRT54G Wireless-G Broadband Router from Linksys.
I was using Bellsouth DSL Internet up until two weeks ago.
I had my DSL modem connected to my router, and the router let me use the internet and share some files and printers with my laptop upstairs.
A few weeks ago we changed to Comcast cable. The technician came in and connected it himself, but only for the desktop. The internet worked perfectly, and still works perfectly on my desktop (the one downstairs). He didn't really give me any instruction or CD-roms for it.
When I tried connecting my router, the internet stopped working. It was weird because the router worked for the file sharing and printer sharing between both my computers, but the internet didn't work. Although, the light for the internet is lit on the router itself.
I even have this program called "AOL Network Magic" which shows a map of what is connected to the router, and it shows that the router and my laptop and desktop are connected, but then it has an "X" for the internet connection.
I have tried everything. I lost all of my CDs and things that came with Linksys, but I downloaded some guides from the Linksys website and it doesn't really help. I tried something called "NetSet", but after I set everything up it says my router is not compatible or something with NetSet. I read a bunch of FAQs, I tried going to comcast and seeing if they had any FAQS about it, but I can't find anything.
Maybe one of you can help me?
Also, I don't know my modem's IP address. I had it for Bellsouth, and sometimes when I would lose my connection I would go there and click on "reconnect" or something like that.
So the only way I can use the internet is to disconnect everything from my router and connect the ethernet cable directly to the modem.You may open the web setup utility page of the router by typing its IP address on your browser's address bar. By default, it is 192.168.1.1. When you're asked for username, you may leave it blank. For password, its "admin". If in case that does not work, reset your router at the back for 30 secs and do a power cycle again, see if it becomes accessible after that...
"The war between heaven and hell depends on the choices we make, and those choices require sacrifice. That's the test" -
MyDAQ fails Self-Test and will not work with any software
I cannot get the myDAQ to communicate properly. I did everything I could to make sure that the device was detected by the computer. It shows up in Device Manager under Data Acquistition Devices as NI myDAQ and in NI MAX as "myDAQ1", but I receive errors when trying to use it with any NI program.
Trying to self-test or reset the device in MAX gives these errors:
-The self test failed. -88705 The specified device is not present or is not active in the system. The device may not be installed on this system, may have been unplugged, or may not be installed correctly.
-There was a problem resetting the device. Error code: 80040383.
It also gives this error when trying to use the Elvis Oscilloscope:
-Error -200324 occurred at ELVISmx_DAQmx Create Channel (AI-Voltage-Basic).vi:1
Possible reason(s):
NI-DAQmx is unable to communicate with the device. Make sure the device is present in and accessible to the system, is not currently being reset, and is not reserved by another driver such as Traditional NI-DAQ (Legacy).
I have uninstalled and reinstalled and repaired all installed NI products twice. I updated to NI-DAQmx 9.8.0 and am using NI Elvis 4.5. I have checked NI Device Loader and mDNS Responder Service in Services and everything is running properly. I have also tried Reset Configuration Data in NI MAX several times. I turned Fast Startup off as suggested in one article. I have tried plugging it into every single USB port on my computer; all 8 of them. The blue led is on when plugged in, but I cannot figure out why it will not work with any of the software. I am running Windows 8 Pro 64-bit. Also, it completely works on the school computers running Windows 7 without any problems. I would like to have it functioning with all the NI software purchased, but all I want to do is use the oscilloscope software for now. It has honestly been way too much work and a huge loss of time for something that should work out of the box. Please help me resolve this, thanks.
Attachments:
ni_support.zip 341 KBHi chaka123,
I had already read that article so it wasn't anything I hadn't tried. I did, however, uninstall both NI DAQmx and NI ELVISmx, ran the registry cleaner and then plugged my device in. Now it shows up as USB Flash Firmware Updater. This is actually what it showed the first time I plugged this in out of the box. After much troubleshooting I was finally able to get it to at least recognize it as a myDAQ. This is problem I know others have had.
To answer your questions:
Does the Test Panels work at all?
I am not sure, I didn't try it before uninstalling. Now the Test Panels isn't an option because it is recognized as the Flash Firmware Updater.
Have you tried to delete the device in MAX?
Once again, I cannot because it shows up as Flash Firmware Updater.
Which is the color of the icon on the left side of “myDAQ1”?
It was green before the uninstall. Now it shows the USB symbol.
I tried deleting the driver. When I plugged the device back it, Windows started automatically trying to load a driver for it. Now it shows as NI myDAQ with a yellow exclamation symbol. In MAX it shows as NI myDAQ with a USB symbol. Under Driver Details it says "Windows does not have a driver associated with your device."
What folder can I manually point Device Manager to in order to load the correct driver?
Attachments:
devicemanager.PNG 40 KB -
on updating my iphone it shows no network inspite the sim inserted,now it also not working with itunes.
i cant see menu page on display screenhttp://support.apple.com/kb/HT1808
-
I bought the Keynote app for my MacBook, but when I open the application and try to install it, I get an error message saying that the application will not work with my MacBook. What gives? And, can I please request a refund? ($19.99 = a week's groceries).
Thank you for your help! - I did try looking for all available specs about Keynote on the Apple iTunes website, and found nothing that could help me. HELP!1
Close all iWork applications
2
Uninstall Keynote; this must be done with an application remover tool to delete the installation properly. Appcleaner is known to work correctly for this purpose, it is free and can be downloaded from here: Appcleaner Download
3
empty the trash
4
shutdown the Mac and restart. After the start up chime, hold down the shift key until the apple logo appears
let the Mac complete the start up procedure completely, it will take longer than usual as the hard drive is being repaired
5
Reinstall Keynote by logging into the Mac App Store using download / install -
downloaded yosemite continuity is not working with my iPhone 6. Both on same wifi network and iCloud account.. not sure how to set it up any help is appreciated
Connect your iPhone, iPad, iPod touch, and Mac using Continuity
-
my voice call services is not working with cellular network...only works fine with wifi..please help?
Since you have already done some sort of reset on your Airport Express, you might as well make sure it was a "hard reset" - follow the instructions for a hard reset found at:
http://docs.info.apple.com/article.html?artnum=108044
Since your Mac is running Leopard, you need to configure the Airport Express using the Airport Utility found in the Applictions->Utilities folder. You cannot install the old software that was supplied on the CD you got with the Airport Express.
In future - if you do something bad with network settings on your Mac, do NOT try to fix it with the Airport Utility. The Airport Utility is only used to configure the Airport Express - and since the problem you have created is on the Mac and not the Airport Express, there is no need to be using the Airport Utility and especially there is no need to be resetting the Airport Express. -
I keep trying to download Photoshop CS3 and a get a 404 error page, does Photoshop CS3 not working with a new Mac operating system?
you must also use a browser that allows cookies. try a different browser or download from adobe.com
Downloads available:
Suites and Programs: CC 2014 | CC | CS6 | CS5.5 | CS5 | CS4 | CS3
Acrobat: XI, X | 9,8 | 9 standard
Premiere Elements: 12 | 11, 10 | 9, 8, 7
Photoshop Elements: 12 | 11, 10 | 9,8,7
Lightroom: 5.5 (win), 5.5 (mac) | 5.4 (win), 5.4 (mac) | 5 | 4 | 3
Captivate: 8 | 7 | 6 | 5
Contribute: CS5 | CS4, CS3
Download and installation help for Adobe links
Download and installation help for Prodesigntools links are listed on most linked pages. They are critical; especially steps 1, 2 and 3. If you click a link that does not have those steps listed, open a second window using the Lightroom 3 link to see those 'Important Instructions'. -
Airport express not working with optus network
Hi there, the airport express seems not working with my optus network. It is keeping me I cannot access the internet but I do have a wifi signal. Initially I thought there was some problems with Enhernet Wan port on the AE, but after I've done some research I found there might some changes needed to be done with my old router. All I know is im using a NETGEAR router, network type is PPPOE. Also, there were people metioned on the forum that theold modern should be changed to brigdeging mode. I have no idea what is it. Please help. cheers.
Configuration is simple if you start from a factory default condition. Then connect the Airport to AC power and finally to the Internet modem (or modem/router). Open Airport Utility on your Mac or other computer and accept all of the recommendations. After confirming that it works, insert your desired administrative and WiFi passwords.
Do not expect the Airport to respond instantly to the configuration commands. BE PATIENT! -
Wi-Fi to your iPhone does not work with the knowledge that I have worked Restart for the same purpose network does not work What is the solution please help as soon as
Okay, the Wi-Fi doesn't work. Turn it on.
Beyond that, we cannot offer any other assistance as you've failed to provide useful details of the problem.
When responding, post in your native language as your English makes very little sense. -
Window 10 build 10041 does not work with Intel 82579V Gigabit Ethernet on ASUS motherboard
I originally posted this question here:
answers.microsoft.com/en-us/insider/forum/insider_wintp-insider_update/window-10-build-10041-does-not-work-with-intel/6729892f-83aa-4822-b20a-ea84f4fd06c7
and was asked to post it on this forum...
I updated a computer I have which is a quad core i7 that I built and includes an ASUS motherboard with Intel 82579V Gigabit Ethernet built in. Windows 10 preview 9926 worked fine with this network adapter. Window 10 build 10041 does not, and I have tried
it twice so far. I even went as far as buying a Thunderbolt-Gigabit Ethernet Adapter (Broadcom, sold by Apple)... and while it installed the driver automatically, it did not work either. Each time you try to view the properties of either of them, it locks
up or give an error. In fact, doing much of anything with the Intel adapter icon assures you of not being able to do a clean reboot... have to kill power. I have finally gone back the previous version 9926, which has its issues but no where near as bad
as not having any network connectivity! Does anyone have this issue and a workaround?
Note, there are two images on the windows 10 preview forum that I posted this question on. I could not post the full link as I was getting a message here that links and graphics are not allowed.Thanks Roger, I posted the following yesterday in the other thread (thinking it was this thread - confusing after they moved it here)... It may be that the new driver fixes the issue that 10041 has with it, but I have not tried that yet. If I do I will update
this... Thanks!
I have more information about this, which basically exonerates any issue with the Intel 82579V Gigabit Ethernet hardware or software. I have 3 computers with Windows 10 preview so I have multiple angles to see issues from. With this I have found a culprit
(but I suspect not just the only culprit) in this above mentioned problem...
10041 build combined with installing (or attempting to install) CISCO VPN Windows 7 64bit 5.0.07.0440-k9 client causes the issue mentioned above. I confirmed this on a completely different machine with a totally different Ethernet adapter. First machine
is an ASUS motherboard in a tower system I built, with the Intel 82579V Gigabit Ethernet hardware built in. Second machine is a Gateway Laptop from 2008 which has a Marvell Yukon 88E8057 PCI-E Gigabit adapter built in. Build 10041 will work fine with my 2008
laptop, including the MS VPN client (which I have tested). However, if you attempt to install or even uninstall the Cisco client you will have to do a recovery to a restore point (as I have done twice) in order to get your network working again. Installing
or attempting to install (because it never even does install properly and times out), CISCO VPN client will render your entire network unusable. Going back to a restore point saved me and I am still running 10041 but I can't use CISCO VPN client any longer.
I could with build 9926, including on all 3 machines. I now have 9926 on two machines and 10041 on only the 2008 laptop.
Hopefully this above information helps someone resolve the issue. I will also mention, even though my network is working on the 2008 laptop, I still can't go into the Control Panel\Network and Internet\Network Connections and right mouse click on the Marvell
Yukon 88E8057 PCI-E Gigabit adapter icon. I get an error when clicking on Properties menu popup : "An unexpected error has occurred". So something is still up with my network adapter driver or windows software, but it could be a side effect of all
that has happened with the Cisco software install attempts under 10041.
Another note: CISCO Anyconnect also has the issue. -
Standby PRI not working with voice Gateway Router & CUCM
Hi ALL ,
GOOD Day all of you .
I am facing a big problem i.e standby PRI not working with VG & CUCM , I have checked all the configuration parameter on VG & CUCM found ok but I am unable to make any call from standby link also incoming not come on the standby link . When I make a call on my Pilot no but getting busy tone .
I observer the some errors on VG like Cause i = 0x8286 - Channel unacceptable on my second PRI channel .
Please help me to reslove this proem .
Following are the PRI configuration Parameter on CUCM .
Product Specific Configuration Layout
Line Coding : HDB3
Framing : NON CRC4
Clock : External
Input Gain (-6..14 db) 0
Output Attenuation (-6..14 db) 0
Echo Cancellation Enable
Echo Cancellation Coverage (ms) 64
PRI configuration on VG
interface Serial0/0/1:15
encapsulation hdlc
isdn switch-type primary-net5
isdn incoming-voice voice
isdn bind-l3 ccm-manager
BR,
SANDIPANHi Craig ,
Thanks for your reply .
We are using the full 30 channel E1 PRI .
following are PRI Channel Statistics:
%Q.931 is backhauled to CCM MANAGER 0x0003 on DSL 1. Layer 3 output may not apply
ISDN Se0/0/0:15, Channel [1-31]
Configured Isdn Interface (dsl) 1
Channel State (0=Idle 1=Proposed 2=Busy 3=Reserved 4=Restart 5=Maint_Pend)
Channel : 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
State : 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 3 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Service State (0=Inservice 1=Maint 2=Outofservice 8=MaintPend 9=OOSPend)
Channel : 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
State : 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 2 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Please find following debug error
VG_RO_01#isdn test call interface serial 0/0/0:15 09665484798
Mar 7 03:00:54.570: ISDN Se0/0/0:15 Q921: User RX <- RRp sapi=0 tei=0 nr=5
Mar 7 03:00:54.570: ISDN Se0/0/0:15 Q921: User TX -> RRp sapi=0 tei=0 nr=4
Mar 7 03:00:54.570: ISDN Se0/0/0:15 Q921: User TX -> RRf sapi=0 tei=0 nr=4
Mar 7 03:00:54.574: ISDN Se0/0/0:15 Q921: User RX <- RRf sapi=0 tei=0 nr=5
CCIL_PUNE_DR_VG_RO_01#
Mar 7 03:00:55.994: ISDN Se0/0/0:15 Q931: Applying typeplan for sw-type 0x12 is 0x0 0x1, Called num 09665484798
Mar 7 03:00:55.994: ISDN Se0/0/0:15 Q921: User TX -> INFO sapi=0 tei=0, ns=5 nr=4
Mar 7 03:00:55.994: ISDN Se0/0/0:15 Q931: SETUP pd = 8 callref = 0x0084
Bearer Capability i = 0x8890
Standard = CCITT
Transfer Capability = Unrestricted Digital
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA9839F
Exclusive, Channel 31
Called Party Number i = 0x81, '09665484798'
Plan:ISDN, Type:Unknown
Mar 7 03:00:56.006: ISDN Se0/0/0:15 Q921: User RX <- RR sapi=0 tei=0 nr=6
Mar 7 03:00:56.018: ISDN Se0/0/0:15 Q921: User RX <- INFO sapi=0 tei=0, ns=4 nr=6
Mar 7 03:00:56.018: ISDN Se0/0/0:15 Q931: RELEASE_COMP pd = 8 callref = 0x8084
Cause i = 0x8286 - Channel unacceptable
Mar 7 03:00:56.022: ISDN Se0/0/0:15 Q921: User TX -> RR sapi=0 tei=0 nr=5
Mar 7 03:00:59.995: ISDN Se0/0/0:15 Q921: User TX -> INFO sapi=0 tei=0, ns=6 nr=5
Mar 7 03:00:59.995: ISDN Se0/0/0:15 Q931: SETUP pd = 8 callref = 0x0084
Bearer Capability i = 0x8890
Standard = CCITT
Transfer Capability = Unrestricted Digital
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA9839F
Exclusive, Channel 31
Called Party Number i = 0x81, '09665484798'
Plan:ISDN, Type:Unknown
Mar 7 03:01:00.007: ISDN Se0/0/0:15 Q921: User RX <- RR sapi=0 tei=0 nr=7
Mar 7 03:01:00.019: ISDN Se0/0/0:15 Q921: User RX <- INFO sapi=0 tei=0, ns=5 nr=7
Mar 7 03:01:00.019: ISDN Se0/0/0:15 Q931: RELEASE_COMP pd = 8 callref = 0x8084
Cause i = 0x8286 - Channel unacceptable
Mar 7 03:01:00.019: ISDN Se0/0/0:15 Q921: User TX -> RR sapi=0 tei=0 nr=6
Mar 7 03:01:03.995: ISDN Se0/0/0:15 Q921: User TX -> INFO sapi=0 tei=0, ns=7 nr=6
Mar 7 03:01:03.995: ISDN Se0/0/0:15 Q931: RELEASE_COMP pd = 8 callref = 0x0084
Cause i = 0x80E6 - Recovery on timer expiry
Mar 7 03:01:03.995: ISDN Se0/0/0:15 **ERROR**: CCPCC_CallOrigination: SETUP timed-out (2nd T303) to NETWORK. The SETUP failed.
BR ,
SANDIPAN -
External USB HD does not work with HAL:
External USB HD does not work with HAL:
From the last 10 days the HAL auto-mount with ntfs-3g file system of my external hard drive does not woks.
But the manual mount procedure with the command mount -t ntfs-3g /dev/sdb* /mnt/XYZ works.
I've followed the instructions in the wiki: http://wiki.archlinux.org/index.php/HAL and the system has worked up to the last kernel or HAL update.
My fat32 usb-stick works without any problem.
If I try to open the device with KDE it appears an error popup wit this message:
TODO: have to rethink extra options
Error: kio_media_mount_helper
The log from the kernel.log is
Nov 6 22:03:16 myhost usb 5-1: new high speed USB device using ehci_hcd and address 4
Nov 6 22:03:16 myhost usb 5-1: configuration #1 chosen from 1 choice
Nov 6 22:03:17 myhost Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
Nov 6 22:03:17 myhost ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Nov 6 22:03:17 myhost Initializing USB Mass Storage driver...
Nov 6 22:03:17 myhost scsi6 : SCSI emulation for USB Mass Storage devices
Nov 6 22:03:17 myhost usb-storage: device found at 4
Nov 6 22:03:17 myhost usb-storage: waiting for device to settle before scanning
Nov 6 22:03:17 myhost usbcore: registered new interface driver usb-storage
Nov 6 22:03:17 myhost USB Mass Storage support registered.
Nov 6 22:03:22 myhost scsi 6:0:0:0: Direct-Access WDC WD32 00JB-00KFA0 0811 PQ: 0 ANSI: 0
Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] 625142448 512-byte hardware sectors (320073 MB)
Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] Test WP failed, assume Write Enabled
Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] Assuming drive cache: write through
Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] 625142448 512-byte hardware sectors (320073 MB)
Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] Test WP failed, assume Write Enabled
Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] Assuming drive cache: write through
Nov 6 22:03:22 myhost sdb: sdb1
Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] Attached SCSI disk
Nov 6 22:03:22 myhost sd 6:0:0:0: Attached scsi generic sg2 type 0
Nov 6 22:03:22 myhost usb-storage: device scan complete
and the error.log is
Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] Assuming drive cache: write through
Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] Assuming drive cache: write through
Do you have some idea ....
Bye.I have done the following:
Downloaded the patched hal version.
used makepkg in /abs/local/trunk/ to create a pkg for pacman
used sudo pacman -U pkgname to install it.
used sudo nano /etc/hal/fdi/policy/preferences.fdi to create the fdi file with the following content:
saved the file and removed my ntfs entryes from fstab and rebooted. and still there is no automount off ntfs partitions.
have i done something wrong?
br fjodork
WARNING: what follows is a guide of what did work for me, I'm still in an early stage of learning linux, so please correct me if anything of what follows is wrong/dangerous/stupid. As I said, this worked for me, it's not pretty, since I was learning each step on the fly and I'm sure there are better ways to do this.
So fjodork, you seem to have done the the necessary steps, though i couldn't get it to work until i first removed hal without dependencies
pacman -Rd hal
it will give you some warning about the dependencies, ignore it since we are reinstalling hal in a few steps.
First i tried to follow Raymano's link, obviously it showed me nothing in the browser so I thought it might be a broken link.
So I downloaded the source tarball from here http://hal.freedesktop.org/releases/hal-0.5.10.tar.gz
unpacked it changed the /tools/hal-storage-mount.c as per Milfadoodle's instructions.
at first I tried to compile directly from source, the process would finish without a glitch though after reboot nothing changed, as if hal weren't
installed, i guess there were issues with paths. anyway read on
Then repacked the source in tarball, copied it to /var/abs/extra/system/hal and modified the PKGBUILD as follows
makedepends=('pkgconfig' 'gperf')
options=('!libtool')
install=hal.install
source=(${pkgname}-${pkgver}.tar.gz #removed url so makepkg looks in the current directory for the tarball
hal
hal-policy.patch
cryptsetup_location.patch
hal-0.5.9-hide-diagnostic.patch
ntfs3g-valid-options.patch)
md5sums=('6641c30a27c00485c6accac5110ff911' # replace with md5sum of your package's sourceball (run md5sum filename)
'882f67668cb14a0a9e4a27ef22278027'
'5ba8b610aa9763a5f42b9f7cbd7a86ad'
then makepkg (i had to add --asroot, don't ask why
and finally pacman -U hal-0.5.10-1-i686.pkg
another reboot and everything worked without a glitch!:D (yeah i know i still haven't got rid of the reboot mentality )
I have also put the policy files as per the wiki instructions.
PS: I know this is a dirty way to getting things done but as i said, I'm just starting
If anyone could comment/correct/explain this post I'd be more than happy, the automount issue was bothering me for about a month now (you'll say why do I need ntfs in the first place? well, I only recently switched for Linux as my primary OS, these are some relics of the M$ era
Maybe you are looking for
-
Why am I getting a "Problem With Previous Purchase" when I haven't purchased anything?
Sometimes, quite randomly when I open anything on my iPad or iPhone and try to update an app or something of the like, iTunes asks me to verify my billing information. It gives me the reason "There was a problem with a previous purchase." And asks me
-
Hi Experts, I'mcreating a popup in a standard way from a normal View called 'MAIN': lr_popup = lr_window_manager->create_window( modal = abap_true window_name = 'WND_POPUPMAIN' title = lv_text close
-
Resizing/compresing images within a document
Hi I am trying to compress all images within a document I've just creacted, in order to avoid having a 20Mb size document, but I cannot find the tool anywhere. I am just new to Pages, transfered from Office Word, where this task can easily be done by
-
Hello, I use Photoshop Elements to edit photos. Even after editing with P.E. I can see the original date the photo was taken (as well as the modified date). When I import into iPhoto, I get a brand new date (the date of import) and cannot see the ori
-
how will you go about if you're going to add an API which is runnable in the handset, how is that? EXAMPLE: I have a CLASS FILE which I want to act as an API or library, lets say, a BLINKING TEXT API. should I do this: import test.blinkingtext.blink;