HELP ! 875P Neo JAUD1 for front Audio with Thermaltake XASER III

I am trying to connect my new Thermalake case V2000A (the aluminium tower with 7 FANs) front (well top) audio connetors to JAUD1 on the motherboard (875P Neo FiS2R)
The XASER III wires say :
EAR L jumped with EAR L (Case manual says connect two "EAR L" to "BLINE_OUT_L" and "Line out_L" on motherboard)
EAR R jumped with EAR R (Case manual says connect two "EAR R" to "BLINE_OUT_R" and "Line out_R" on motherboard)
GND (Case manual says connect to "GROUND" or "AGND" on motherboard)
MIC IN (Case manual says connect to "MIC INPUT" or "MIC 2" on motherboard)
MIC VCC (Case manual says connect to "MIC POWER" or "MICPWR" on motherboard)
The JAUD1 connector on the motherboard comes with TWO green jumpers out of factory. One jumper shorting pins 9 & 10 and the other jumper shorting pins 5 & 6.
Page 2-25 of the motherboard manual says:
Pin 1 - AUD_MIC Front Panel Microphone input signal
Pin 2 - AUD_GND Ground used by analog Audio Circuits
Pin 3 - AUD_MIC_BIAS Microphone Power
Pin 4 - AUD_VCC Filtered +5V used by analog audio circuits
Pin 5 - AUD_FPOUT_R Right Channel audio signal to front panel
Pin 6 - AUD_RET_R Right channel audio signal return from front panel
pin 7 - HP_ON Reserved for future use to control headphone amplifier
pin 8 - KEY No pin
pin 9 - AUD_FPOUT_L Left channel audio signal to front panel
pin 10 - AUD_RET_L Left channel audio signal return from front panel
Now, I assume :
Case "MIC VCC" should go on Pin 3 (or maybe Pin 4 ?)
Case "MIC IN" should go on Pin 1
Case "GND" should go on Pin 2
Case "EAR R" should go on Pins 5 & 6 (I need to REMOVE the green jumper ?)
Case "EAR L" should go on Pins 9 & 10 (I need to REMOVE the green jumper ?)
Thanks for all help !

I have yet to put the PCI cards inside but so far I was able to reach that end corner of the motherboard with the case top sound cables.
As soon as I get answers on this Forum to my queries from more knowledged people about the right cabling (this and other posts on firewire and something else), I will then be able to finish all connections and finally place also the PCI cards and the video card and will let you know if it all went ok without the sound case cable stretching too much.
Thanks.
Quote
Originally posted by rwfish
Did you have any trouble getting the cables to stretch to the motherboard pins? I gave up on my (similar) setup.

Similar Messages

Help Connecting JAUD1 to Front Audio on Case

Can anybody tell me how to hook up the following:
Case Front Audio Wires
A - Mic In
B - Mic VCC
C - GND
D - Ear L
E - Ear R
F - Line L
G - Line R
K8NGM2-FID 7207 Motherboard JAUD1
1 - Port 1L
2 - GND
3 - Port 1R
4 - PRESENCE #
5 - Port 2R
6 - SENSE 1_RETURN
7 - SENSE_SEND
8 -
9 - Port 2L
10 - SENSE2_RETURN
I don't want to screw anything up and any help would be greatly appreciated! Thanks and have a great day!!!

Hi Frankenputer,
I'd also like to thank you for such a fast response! I do have a copy of the manual in my grubby little hands and I did read it. That's how I was able to identify the motherboard pinouts in my first post. I guess that one slipped by you . The link you provided is great, it'll come in handy if I ever misplace the manual down the road.
My problem stems from the way the case manufacturer labelled the wires for the front audio connector e.g. using a naming convention that differs from that of the Intel Front Panel I/O Connectivity specification. Specifically the Mic-VCC, Line-L and Line-R wires.
Stated simply, I was hoping one of the experts here might be able to tell me/confirm if Mic-VCC should be connected to pin 3 - AUD_MIC_BIAS or to pin 4 - AUD_VCC, and if Line-R should be connected to pin 6 and Line-L to pin 10 on the motherboard.
Again, thanks for your reply and have a great day!!!
Fred

Front audio with PCI sound card?

Well, the front audio on my Antec P160W worked perfectly with the integrated sound, but I changed to my SoundBlaster Audigy Player because of the HORRIBLE audio quality. Now the front audio ports don't work. What do I need to do to make it work again? I'm not going back to the integrated.
At first I thought that I had to put the connectors for the front audio on the sound card, but the manual of it doesn't show any of those features.

I was wondering that myself. The only thing I think you could possibly do is have both the onboard and the pci sound card enabled and use the onboard sound just for the headphones. I have no tried this yet as I do have the cables connected to the mobo but I have the onboard sound disabled.

Help formatting Hard Drive for best compatibility with Mac OSX 10.5!

I have a 1TB hard drive that I recently purchased. I would like for format it for best compatibility with Leopard. I must be doing something wrong because everything I try, I get an error.
Here's the details of my drive.
What do I need to do in Disk Utility?
Disk Description : WL1000GS A1672 Media
Total Capacity : 931.5 GB (1,000,204,886,016 Bytes)
Connection Bus : USB
Write Status : Read/Write
Connection Type : External
S.M.A.R.T. Status : Not Supported
USB Serial Number : 240077140FFF
Partition Map Scheme : Master Boot Record
Main Partition (Only managed to get it's name to CORY.):
Mount Point : /Volumes/CORY
Capacity: 931.5 GB (1,000,204,853,760 Bytes)
Format : MS-DOS (FAT32)
Available : 931.3 GB (999,959,166,976 Bytes)
Owners Enabled : No
Used : 1.4 MB (1,507,328 Bytes)
Number of Folders : 0
Number of Files : 0

Looks like that's working. My problem was I didn't select GUID Scheme. Thanks.
EDIT: Yup that did the trick. Thanks so much.

Help:UIModel.xml file for ADF Tree with three level depth

Hello,
I am trying to create a DCTree with structure like this:
root....branch1----child11,child12
..........branch2......branch21---child212,child212
............................branch22---child221,child222
Because I can not create more than one binding rule due to the problem that "Add New Rule" button disappears after the first rule is created when I use the tool under Createbinding/Input/Tree to create the DCTree.
Could somebody post or send me a script of the UIModel.xml file of the tree structure above so that I can work around this problem?
Thanks in advance,
Deborah

Hi,
I haven't test it for more than 3 layers but I have never seen this limitation mantioned anywhere.
I used HGrid and this is my code:
1. UIX file (the relevant part highlighted):
<?xml version = '1.0' encoding = 'windows-1252'?>
<page xmlns="http://xmlns.oracle.com/uix/controller"
xmlns:ui="http://xmlns.oracle.com/uix/ui"
xmlns:data="http://xmlns.oracle.com/uix/ui"
xmlns:ctrl="http://xmlns.oracle.com/uix/controller"
xmlns:html="http://www.w3.org/TR/REC-html40" expressionLanguage="el"
xmlns:myTemplate="test">
<templates xmlns="http://xmlns.oracle.com/uix/ui">
<templateImport source="baseTemplate.uit"/>
</templates>
<content>
<dataScope xmlns="http://xmlns.oracle.com/uix/ui">
<provider>

</provider>
<contents>
<document>
<metaContainer>

<head title=""/>
</metaContainer>
<contents>
<body>
<contents>
<form name="form0">
<contents>
<myTemplate:baseTmpl title="" xmlns:myTemplate="test">
<contents>
<rowLayout>
<contents>
<link text="Bets View" destination="browseCustBets.do"/>
<spacer width="10" height="10"/>
<link text="Customer Bets" destination="viewCustBets.do"/>
</contents>
</rowLayout>
<rowLayout>
<contents>
<spacer width="10" height="10"/>
</contents>
</rowLayout>
<rowLayout>
<contents>
<hGrid id="hg1" treeData="${uix.data.treeData}" proxy="${uix.eventResult.hGridProxy}">
<columnHeaderData>
<col text="Email"/>
<col text="Bet Date"/>
<col text="ID"/>
<col text="Is Winner"/>
<col text="Amount"/>
<col text="Rate"/>
</columnHeaderData>
<columnHeaderStamp>
<text text="${uix.current.text}"/>
</columnHeaderStamp>
<columnFormats>
<columnFormat columnDataFormat="textFormat" width="140"/>
<columnFormat columnDataFormat="textFormat" width="160"/>
<columnFormat columnDataFormat="textFormat" width="40"/>
<columnFormat columnDataFormat="textFormat" width="70"/>
<columnFormat columnDataFormat="textFormat" width="70"/>
<columnFormat columnDataFormat="textFormat" width="40"/>
</columnFormats>
<contents>
<text text="${uix.current.Email}"/>
<text text="${uix.current.BetDate}"/>
<text text="${uix.current.BetID}"/>
<text text="${uix.current.IsWinner}"/>
<text text="${uix.current.Amount}"/>
<text text="${uix.current.Rate}"/>
</contents>
</hGrid>
</contents>
</rowLayout>
</contents>
<tabs/>
<pageButtons/>
<globalButtons/>
<pageHeader/>
<start/>
<end/>
<about/>
<copyright/>
<privacy/>
<corporateBranding/>
<productBranding/>
</myTemplate:baseTmpl>
<formValue name="${bindings.statetokenid}" value="${bindings.statetoken}" id="_uixState"/>
</contents>
</form>
</contents>
</body>
</contents>
</document>
</contents>
<provider>
<data name="treeData">
<method class="view.CreateTreeData" method="getTreeData"/>
</data>
</provider>
</dataScope>
</content>
<handlers>
<event name="*">
<method class="view.BetDetailsAction" method="doHGridEvent"/>
</event>
</handlers>
</page>
2. CreateTreeData class:
It has a static method getTreeData() that returns a DataObject containing the tree nodes. This methode is mentiond in <provider> node in UIX/XML.
package view;
import java.util.Enumeration;
import model.*;
import oracle.cabo.servlet.BajaContext;
import oracle.cabo.servlet.ServletConstants;
import oracle.cabo.servlet.ui.BajaRenderingContext;
import oracle.cabo.ui.RenderingContext;
import oracle.cabo.ui.UIConstants;
import oracle.cabo.ui.data.DataObject;
import oracle.cabo.ui.data.servlet.HttpSessionDataObject;
import oracle.cabo.ui.data.tree.SimpleTreeData;
import oracle.jbo.ApplicationModule;
import oracle.jbo.ViewObject;
import oracle.adf.model.BindingContext;
import oracle.adf.model.binding.DCDataControl;
//import oracle.jbo.common.Configuration;
import javax.servlet.http.HttpSession;
import oracle.jbo.client.Configuration;
public class CreateTreeData
public CreateTreeData()
public static DataObject getTreeData(RenderingContext context, String namespace, String name)
// create root node
SimpleTreeData root = new SimpleTreeData();
int BetID = 0;
// get the parameter from url
BajaContext bContext = (BajaContext) context.getProperty(ServletConstants.BAJA_NAMESPACE,
BajaRenderingContext.BAJA_CONTEXT_PROPERTY);
HttpSession session = bContext.getServletRequest().getSession(true);
try
//BetID = new Integer(( bContext.getServletRequest( ) ).getParameter( "BetID" )).intValue();
String s = ( bContext.getServletRequest( ) ).getQueryString();
BetID = new Integer(s).intValue();
session.setAttribute("BetID", s);
//BetID = new Integer(session.getAttribute("BetID").toString()).intValue();
catch ( Exception ex)
// log the error on the console
BetID = new Integer(session.getAttribute("BetID").toString()).intValue();
//System.out.println( "Parameters cannot be retrieved" );
//System.out.println( ex.getMessage() );
String amDef = "model.AppModule";
String config = "AppModuleLocal";
ApplicationModule am = Configuration.createRootApplicationModule(amDef, config);
AppModuleImpl myAm = (AppModuleImpl)am;
root = myAm.createNodesData(BetID);
myAm.remove();
Configuration.releaseRootApplicationModule(am,true);
// return the tree
return root;
3. createNodesData(int Id) is the actual function that creates the data structure containing the nodes.
It is in AppModule. The actual tree is kept in one table and every node knows its parent ID. There is no limitation in depth.
This function is called recursively until the tree is finished and the parameter Id is the Id of the parent node that I want to be listed. Tne top parent nodes has null in ParentID field.
public SimpleTreeData createNodesData(int Id)
SimpleTreeData tData = new SimpleTreeData();
String baseSQL =
"SELECT Bet.ID, Bet.CUST_LOGIN_ID, Bet.BET_CLASS_ID, Bet.PARENT_BET_ID," +
"Bet.CHAMPIONSHIP_ID, Bet.AMOUNT, Bet.WIN_RATE, Bet.IS_WINNER, Bet.BET_DATE, " +
"BetClass.NAME, CustLogin.EMAIL, CustLogin.ID AS CUST_LOGIN_ID " +
"FROM BET Bet, CUST_LOGIN CustLogin, BET_CLASS BetClass " +
"WHERE (Bet.CUST_LOGIN_ID = CustLogin.ID) AND (Bet.BET_CLASS_ID = BetClass.ID) ";
if(Id!=0){
String sqlStmt = baseSQL + " AND (Bet.ID = '"+ Id +"')";
ViewObject betVo = this.createViewObjectFromQueryStmt("betVo", sqlStmt);
betVo.executeQuery();
if(betVo.hasNext())
//SimpleTreeData tData = new SimpleTreeData();
tData.setText(betVo.first().getAttribute("NAME").toString());
if(betVo.first().getAttribute("PARENT_BET_ID")==null)
tData.put("Email", betVo.first().getAttribute("EMAIL").toString());
tData.put("BetDate", betVo.first().getAttribute("BET_DATE").toString());
tData.put("BetID", betVo.first().getAttribute("ID").toString());
tData.put("IsWinner", betVo.first().getAttribute("IS_WINNER").toString());
tData.put("Amount", betVo.first().getAttribute("AMOUNT").toString());
tData.put("Rate", betVo.first().getAttribute("WIN_RATE").toString());
if(Integer.parseInt(betVo.first().getAttribute("BET_CLASS_ID").toString())>1){
tData.setExpandable(UIConstants.EXPANDABLE_EXPANDED);
betVo.remove();
String sqlStmt = baseSQL + " AND (Bet.PARENT_BET_ID = '"+ Id +"')";
ViewObject betVo = this.createViewObjectFromQueryStmt("betVo" + Id, sqlStmt);
betVo.executeQuery();
while(betVo.hasNext()){
tData.addChild(createNodesData(Integer.parseInt(betVo.next().getAttribute("ID").toString())));
betVo.remove();
return tData;
Hope this will help...

Need help serializing an AbstractTableModel for a JTable with cell editing.

Fun times are ahead. Here we go!
I have a JTable that contains data I'd like to serialize out to a file to be restored and viewed later.
So I tried saving the AbstractTableModel subclass out to a file. Whenever I do this, I get the following error message:
java.io.NotSerializableException: javax.swing.JTable$CellEditorRemover
Now I know for fact that serializing an AbstractTableModel that was installed in a JTable without cell editing works just fine (my old code did exactly that). As a result, I think that the code that handles events in the AbstractTableModel contains references back out to the JTable, which causes the JTable to be saved no matter what (even though I'm just interested in saving the TableModel only). It causes a bigger file than normal, but file size is not an issue. The only issue I have is that CellEditorRemover (an undocumented inner class of JTable), which is automatically installed for JTables with editable cells, is not serializable.
This leads to the following questions:
1. Is there a way to avoid serialization/deserialization of the CellEditorRemover inner class of JTable?
2. Is there a way to save an AbstractTableModel without saving all of the event listeners associated with it?
I think an answer to either of these questions would go a long way towards solving my problem. Otherwise, I'll resign myself to weeping silently in the corner of my office.
Thanks!

I would suggest that if you can you only save the
data... but i would do this by using the
externalizable interface.
What you will need to do is have the
writeExternal(ObjectOutputStream out) and
readExternal(ObjectOutputStream out) methods in your
class. These will be responsiable for saving the
data.
Here's an example of what you can do in these
methods... this is just a little tidbit from a program
i've written.public void writeExternal(ObjectOutput out) throws
IOException {
          out.writeInt(size);
          out.writeObject(drawName);
          out.writeInt(playersLength);
for(int i = 0; i < playersLength; i++)
) out.writeObject(players);
          out.writeInt(seedsLength);
for(int i = 0; i < seedsLength; i++)
) out.writeObject(seeds[i]);
          out.writeInt(drawLength);
for(int i = 0; i < drawLength; i++)
) out.writeObject(draw[i]);
public void readExternal(ObjectInput in) throws
IOException, ClassNotFoundException {
          size = in.readInt();
          drawName = (String)in.readObject();
          playersLength = in.readInt();
for(int i = 0; i < playersLength; i++) players[i] =
= (String)in.readObject();
          seedsLength = in.readInt();
for(int i = 0; i < seedsLength; i++) seeds[i] =
= (String)in.readObject();
          drawLength = in.readInt();
for(int i = 0; i < drawLength; i++) draw[i] =
= (String)in.readObject();
You can now use your class as you would a Serializable
class, but it will only save the data
Hope this helped
webaf409java
I forgot to add some critical information in my original post. My apologies. :(
I've thought about using Externalizable, but am hesitant to use it because the application would no longer be able to read in files using the old save format (ie, AbstractTableModels for JTables without CellEditorRemovers ). I want to preserve the ability to read the old saved AbstractTableModel formats if possible.
Do you know of a way to revert to the default deserialization mechanism from readExternal? This way, during deserialization, I could do a quick test on the object being read and have the ability to default to the regular deserialization mechanism if the object is of the old type or continue with the new Externalizable stuff if the object is one of the new type. Maintaining file compatibility is key.

Help! Best setup for using A3 with a Drobo?

A little over a month ago, I decided to get "serious" with my photography hobby and plunked down several hundred bucks for a Drobo (4-bay, FireWire800), a couple 1TB drives to go in it, and a copy of Aperture 3.
It took a couple tries (and a couple days) to import my large iPhoto library and get everything up and running. I can see that Aperture has the potential to be a VERY useful tool... its feature set seems like exactly the type of photo manager I need/want.
Unfortunately, Aperture has been very frustrating to use so far. It's just not very responsive... the "lag" is killin me! Sometimes it's EXTREMELY slow, sometimes it's kinda slow, but it's never fast. There's always a delay/lag any time I try to make an adjustment/edit, skip to the next photo, importing and ESPECIALLY when I am deleting photos. Just deleting one 8MB JPEG can take anywhere from 10 seconds to 10 minutes.
I'm wondering if the slow performance issue is because my library and masters are stored on the Drobo (which uses a RAID-like storage system spread across multiple drives). Or do I just not have my preferences set up right? Or is there a corrupt file slowing things down? I don't know....
Anybody out there successfully using Aperture 3 in conjunction with a DROBO? If so, tell me your secret! How do you have your library/masters set up?
I'd appreciate any suggestions and advice!
Here's my specs:
- Aperture version 3.0.2
- Drobo connected via FW800, appx 300GB used, 650GB avail
- Model Name: iMac
- Model Identifier: iMac8,1
- Processor Name: Intel Core 2 Duo
- Processor Speed: 3.06 GHz
- Number Of Processors: 1
- Total Number Of Cores: 2
- L2 Cache: 6 MB
- Memory: 4 GB
- Dual monitor setup
- Besides the Drobo, another 300GB external is attached via FW
Thanks

First let me say I'm a little on the paranoid side when it comes to loosing my work so my backup process will be overkill for most.
I put all my images and my Aperture library on a large internal drive. All my images are referenced. I also put one Aperture vault on the same drive and another vault elsewhere. I allow Time Machine to back up to a partition on the Drobo (2nd gen) via FW800. I also have a external esata swappable bay that I use for full image backup of the Photo HD using Superduper. I keep one swappable image of each critical HD in fireproof storage and rotate them periodically. I also have a DVD archive of all my images that is kept in a different location.
Having all the images online in the same box makes access fast.
Backing up to the Drobo is not real fast, but I manually start Time Machine and go do something else. The backup on the Drobo is primarily so I can go back in time and locate an image I may have deleted but not realized I needed it. The speed of the Drobo is not a problem in this situation.
The Superduper backup is very fast as it only updates the new or updated files.
When I started I had 3 and later 4 500GB drives in the Drobo. I recently swapped them for 1.5TB drives. When I pulled a 500GB and put in a 1.5TB the Drobo took about 4 days to rebuild the data. The second and third swaps took just as long. The forth only a few minutes. Between each swap I checked and the Drobo (as advertised) recovered all the data.
If you can't keep all your images on an internal HD, you might consider keeping your Aperture library and recent images on the internal drive and use Aperture to migrate them to the Drobo as they age. You could also keep one of your vaults on the Drobo. This approach would require you to use referenced images.

Help! using FM for formating date with to_char()

Hi,
Basically my requirement is to format the date in specific format (i.e. DD MM YYYY HH24:MM) and it should avoid the padding zeros.
Ex: 03-Jun-2009 10:01 should be displayed as 3 Jun 2009 10:01.
I was using the below query
to_char(sr.recievedat, 'FMDD Mon yyyy HH24:MI')...
But the thing is it removing the padding zeros from minuites aswell, which i dont require.
For example,
Ex1: 03-Dec-2009 18:10 3 Dec 2009 18:10
*04-Dec-2009 19:01 4 Dec 2009 19:1.. It should be 4 Dec 2009 19:01*
Can some body help me how to control the FM to restrict the padding to some places
Thanks
Phani

Hi try this
sql> select to_char(sr.recievedat, 'FMDD Mon yyyy fmHH24:MI') from dual;example
SQL> select to_char(to_date('01-jan-2009 7:01:06','dd-mon-rrrr HH:MI:SS'), 'FMDD Mon yyyy fmHH24:MI'
) from dual;
TO_CHAR(TO_DATE('01-JAN
1 Jan 2009 07:01

Help flashing UEFI bios for my GTX 680 Twin Frozr III 2GD5/OC

Hi,
I am very new to flashing graphics card bios, so i need some instructions as to how to update my bios to the latest UEFI GOP version. I am using a Z77 platform with Windows 8 Pro and I'm looking forward to the super fast boot times
Here is my current bios file: **http://www.filehosting.org/file/details/434943/GK104.rom**
Here is my serial number: 602-V282-020B1205147435
My model: MSI GTX 680 Twin Frozr III 2GD5/OC
Thank you

I have followed the steps you said, but had a few hiccups on the way:
1) when i was flashing the rom, i was told in the command line dialog box that the pci vendor identification/verification was mismatched, i was prompted to override verification and i pressed "y". Is that ok ? In total, i had to press "y" 2 times as opposed to once as said in your instructions.
2) After flashing bios, I restarted and disabled CSM (compatibility mode) support. My PC booted fine and i reached the lock screen. But when i entered the password, I was introduced to a black screen with only the cursor showing over it. Then my pc crashed with the error IRQ_NOT_LESS_THAN_OR_EQUAL_TO
3) I restarted and logged back again, but was introduced to the same black screen again, but i could gain access to the control panel with CLT+ALT+DEL and it was filled with error reporting tasks. I restarted the third time and finally could log back in without any crashes or black screens, but windows came up with a prompt that it had run into an error and needs to report it.
I am suspecting that it had something to do with the driver or the verification.
PLEASE HELP. Thanks

(help) front audio panel cords-- sound card??

Dear all....
I have an ancient SB Li've! 24 bit SB 040.
Can anybody help me how to connect front audio header (casing) onto the card (ceati've proprietary connector)?
There are 0 pin connector on the card while the casing itself has only 7 pin.
Regards,

I was wondering that myself. The only thing I think you could possibly do is have both the onboard and the pci sound card enabled and use the onboard sound just for the headphones. I have no tried this yet as I do have the cables connected to the mobo but I have the onboard sound disabled.

HP Pavilion A614n Front Audio Port

Hi, I have an HP Pavilion A614N. I need wiring diagram or connector pin out for the front audio/usb/fire wire port ( part #5784520009 Rev. C ). I need to know what wires in the connectors belong to what.

hi,
if you are going to replace the motherboard then no issues on that..
when you will chk the motherboard you will get the audio port and usb port on it..
it should be mentioned on it F_audio or USB_1 or USB_2 f_audio for front audio and USB's are for usb port..
for better help.. chk the front of your audio port and you will see some blank dots on it.. and chk the motherboard you will also see the same jacks on it..
hope it will help..
thx
**Clicking on the Kudos! white star is a nice way to say thank you on any post that helped you or resolved the problem.**
**Selecting "Accept as Solution" for a reply that solves your issue helps others who are searching the web for an answer**

875P Neo-LSR Setup problems

I posted this message last night but I think it got lost in space.
My System
MSI 875P Neo LSR
Intel 2.4C with H/T
2 X 512 Infineon memory sticks
Enermax 350W P/S
ATI AIW 8500DV
Seagate S ATA 120 H/D Partition with 85/35 partitions on SER1
Western Digital P ATA 80 H/D on IDE 1
LG 52 X CD ROM on IDE 2 primary
LG DVD/CDRW Combo IDE 2 slave
19 Samsung Syncmaster
I am having problems with my new 875P LSR. Installed O/S and software using FAT 32 and it wiped on 2 occasions. Could not boot up trying all the sugestions on the web. Using Partition MAgic rescue disk I could still see the drives and was able to check for errors but when I used my old 98 boot disk C: came up with a message of invalid media but D: was still readable? During both the previous setups I used the F6 option and loaded the Intel raid XP driver for ICHR, was this the reason for my loss of system.
On my third try I used the same partitions but did not use the F6 option and also formatted in NFTS (by accident). Everything appeard to be working so far BUT!!!!!. I don't want the system to do over clocking I just want a secure setup for stability in normal use. I do not play games, I use the inter4net, edit my home movies and normal word processing,
Questions
What am I doing wrong?
What should the cofigreration for the bios onboard ID chip be. I have Mine set in Native mode, P ATA + S ATA, NO, NO, Both, S ATA 1st channel, S ATA PO1 PO2 Raid NO
Do I need to use the Intel IAA driver -or- does XP have drivers -or- do I have to download some other driver or controler for the S ATA.
Can anyone suggest a better layout for my system and how can I tel if the computer is operating with the proper drivers for S ATA, P ATA, H/T and all the other gagets on board. Any suggestions and advise will be appreciated
Swan705 in Ontario Canada

Hi back
Thanks again for the response, followed your instructions now I show a 82801eb under the controler section. Is that all I needed? Another question I like to keep a copy of windows 98 se on my other drive and would like to use the F11 key to boot to it. Is there a procedure of installing it so I don't screw up my XP system. I use a disk tray to keep the drive in so I can take it out for safety as I also store backups of my personel files on it. Your sugestions are really appreciated. Swan705

GR going to wrong GL account for PO Item with Account Assignment Category M

Hi Experts,
I need some help on GR posting for PO Item with M as AAC.
PO1 for material ABC with M as Account Assignment Category, when I book GR for this Item, the GL document generated as below.
Dr: PRD (Cost Price Differences)
Cr: WRX (GR/IR)
The material ABC price control is "S" and already have standard cost.
For another material DEF which have ascetically same master data as ABC and got a similar PO2 with M as Account Assignment Category.
But the GR document as below.
Dr: BSX (Inventory)
Cr: WRX (GR/IR)
How can be one same setting got so different results, is there any data in Material or PO make these differences?
Actually the results for material DEF is what we want, how could I avoid the GR results for material ABC.
Thanks~

Thanks you Mukthar,
I have checked all the information and porcess for both material and did a lot of testing in testing system.
Here is what I found.
Case
Material ABC SO: 1111 PO: 6666 (ACC:M)
Material DEF SO:2222 PO: 7777(ACC:M)
All the information in material mast data, SO, PO are the same.
The differences is that:
PO:6666 post GR before Material ABC's standard price release. So the first GR document as below
Dr: PRD (Cost Price Differences)
Cr: WRX (GR/IR)
This is correct document without material stand cost.
The problem we reverse the fist GR document, release standard cost for Material ABC. Then re-do the GR. but the GL document still book into PRD instead of BSX.
If I create a new SO:3333 and PO:8888 (with ACC M) for material ABC now.
The GR could be book into BSX.
It seem like once the PO got GR with 0 standard cost, even I relesed a new price for the material and re do the GR, it still take the previous 0 cost to book inventory which make all the amount into PRD.
Quite Strange

Syntax for taking export with 'Query' parameter

Hi all
Please help me regarding syntax for taking export with query parameter

Hi
exp file=d:\exp.dmp log=d:\exp.log tables=scott.emp query='where empno=10'
exp file=d:\exp.dmp log=d:\exp.log tables=scott.emp query='where ename='''SCOTT''Salman

Need help with msi 875p neo

i just bought one of these and set up my system, but as soon as i flick the power switch on the psu there is a 2 sec delay then it automaticaly boots up without me pushing anything then it just hangs..nothing no boot screen nothing. i check that d brakect thing and it says "Inializing keyboard controller" it stays there and does not change.
my system spec:
msi 875P Neo-FIS2R
intel Pentium 4 3.0GHz 800MHz Fsb
2 x 256 mb pc-3200 OCZ EL-DDR cas 2 @ DDR400
thermal take spark 7
leadtek winfast A280leTD 'Geforce 4 Ti 4200'
WD raptor 36.7 GB SATA 1
Xaser III casing
Thermaltake Purepower 480W
MS intellieye Explorer
plz help me i find no reason for it no to work

Quote
Originally posted by MaKoMaN
thaks for all ur help i found the problem one of my memory sticks had a scratch the other one works fine.. but now what do i do with the scratched one?
did you make the scratch? if not, you got warranty on it that would get you a new one...

HELP ! 875P Neo JAUD1 for front Audio with Thermaltake XASER III

Similar Messages

Maybe you are looking for