HELP!!!!! 915GM Speedster-FA4 PCIe x1 slot not working - SORTED

Hi, I am at my whit’s end with this motherboard, I cannot get the PCIe x1 slot to work. When I use the PCIe x16 slot it recognises the option card OK but the x1 slot will just not see it.
I know the network socket 1 needs to active for the PCIe x1 slot to work.
Any help would be appreciated.
SORTED - IRQ clash with the onboard boot ROM for Lan socket 2 - NOT DOCUMENTED - MSI PLEASE TAKE NOTE

Sorry there is no MSI in here....
It seems that nobody used that config to be able to help.
And no, I'm not from MSI either

Similar Messages

  • 915GM Speedster-FA4 Help needed.

     I have tried to put together a system based on the 915GM Speedster-FA4 motherboard.
     But it just wont post.
     I have installed CPU and memory and PSU, nothing else.
     I have tried two different CPUs, both 400Mhz Dothan, one SL8BA and one SL7GL
     Can anyone confirm that they are compatible with the 915GM Speedster-FA4 motherboard?
     The Jumpers are:  J4 (not connected), J5 (2-3 connected), J6 (2-3 connected)
     I have tried both DDR1 and DDR2 memories (not at the same time)
     Using a 20-pin PSU. I will try to swap PSU, but after that I have run out of ideas
     Is it possible to get any diagnostics from this board???
    Advice please!
     /Anders

    Quote from: Xanlin on 26-January-07, 18:52:12
    I have tried two different CPUs, both 400Mhz Dothan, one SL8BA and one SL7GL
    I think they are called 715 and 735A
    /Anders

  • 915GM Speedster-FA4 - ICH6 or ICH6R which one?

    Hi
    I recently purchased 915GM Speedster-FA4 based setup. I was planning to set it up with raid0 and lived in impression that this motherboad has built in support for it (ICH6R). Manual states that MB is equipped with "optional ICH6R" southbridge, but there isn't any kind of mention how to enable it. There are also whole section about setting up the raid. But of course document starts with enabling raid in BIOS and at least my version (v1.13) doesn't have any options to do this.
    So the question is, does this motherboard have raid support or not, and if there is how to enable it?
    Thanks
    Antti

    Hi
    I recently purchased 915GM Speedster-FA4 based setup. I was planning to set it up with raid0 and lived in impression that this motherboad has built in support for it (ICH6R). Manual states that MB is equipped with "optional ICH6R" southbridge, but there isn't any kind of mention how to enable it. There are also whole section about setting up the raid. But of course document starts with enabling raid in BIOS and at least my version (v1.13) doesn't have any options to do this.
    So the question is, does this motherboard have raid support or not, and if there is how to enable it?
    Thanks
    Antti

  • 915GM Speedster-FA4 - works with DDR2 667MHz?

    Hi folks,
    first of all: sorry for my English - hope you'll understand me
    I've bought a 915GM Speedster-FA4, I will run a P-M 750 on it.
    Now I'm looking for RAM.
    DDR2 400MHz / 533 MHz is supported by the board, but will also 667 MHz RAM run?
    (manufacturer will be Corsair, model: value-ram DDR2 667 MHz)
    I don't have any experience with DDR2 - but e.g. in many
    boards with DDR 333MHz support I ran 400 MHz without any problems.
    Thanks a lot!

    "DDR2 400MHz / 533 MHz is supported by the board, but will also 667 MHz RAM run?"
    should be not a problem, board should accept 667Mhz stick(s) or higher rated and will run it as 400 or 533. if you using 2 memory sticks ensure they are same brand & specification.

  • 915GM Speedster-FA4 , banias CPU support

    Does the MSI 915GM Speedster-FA4 motherboard support Pentium M Banias CPU?
    I think that Celeron M (100MHz FSB series) are similar to Pentium M Banias, but to be confirmed.

    Dothan is newer than Banias. ... so I'm not sure...

  • [Intel] 915GM Speedster FA4

    I have flashed the BIOS to the new 1.13 from the site, but still have problems with overclocking and the SATA HDD.
    When I go above 165FSB, I no longer have SATA drives visible in the BIOS, and the system tries looking for another boot disk.
    Is there anyone out there who has overcome this problem, or is there a newer 'beta' BIOS available to overcome this problem?
    Rig:
    MSI 915GM Speedster FA4
    Pentium-M 730
    512Mb DDR2 @ 533mhz
    Samsung SP2014N through Highpoint Rockethead
    OB graphics
    OB sound
    WinTV Nova-T TV Card
    Philips 16x DVD-RW
    Logitech S510 KB/Mouse/Remote

    No news yet. Maybe you should try visiting the main webpage, they will make annoucements for the official launch dates.

  • MSI 915GM Speedster-FA4

    I've plan to purchase MSI 915GM Speedster-FA4 and combine it with my Pentium M 755 (479pin).
    I searched the web for best price, but I found two different specification for CPU socket, one is Socket 478 and the other is Socket 479. Which one is correct info? ???

    Actually the pentium M comes in socket 479, but according to intels site they do come in 2 different types Micro FCPGA & FCBGA.
    and according to the sSpec# there is a 479pin version of the newer ones.
    the  1.86 comes in both of the ways below - so make sure you get the SL7S9 if you were choosing between them.
    SL7SR  1.86 GHz 533 MHz 90 nm C0 2 MB 479 pin 
    SL7S9  1.86 GHz 533 MHz 90 nm C0 2 MB 478 pin
    here are other sSpec# from the intel site.
    SL7VB  2.26 GHz 533 MHz 90 nm C0 2 MB 478 pin
    SL7SP  2.13 GHz 533 MHz 90 nm C0 2 MB 479 pin 
    SL7SL  2.13 GHz 533 MHz 90 nm C0 2 MB 478 pin
    SL7UZ  2.10 GHz 400 MHz 90 nm B1 2 MB 479 pin 
    SL7V3  2.10 GHz 400 MHz 90 nm B1 2 MB 478 pin
    SL7EM  2 GHz 400 MHz 90 nm B1 2 MB 478 pin
    SL7SM  2 GHz 533 MHz 90 nm C0 2 MB 478 pin
    SL7SQ  2 GHz 533 MHz 90 nm C0 2 MB 479 pin 
    SL7SR  1.86 GHz 533 MHz 90 nm C0 2 MB 479 pin 
    SL7S9  1.86 GHz 533 MHz 90 nm C0 2 MB 478 pin
    SL7EN  1.80 GHz 400 MHz 90 nm B1 2 MB 478 pin
    SL7SA  1.73 GHz 533 MHz 90 nm C0 2 MB 478 pin
    SL7S8  1.73 GHz 533 MHz 90 nm C0 2 MB 479 pin 
    SL6N5  1.70 GHz 400 MHz 0.13 micron B1 1 MB 478 pin
    SL6N9  1.70 GHz 400 MHz 0.13 micron B1 1 MB 479 pin 
    SL7EP  1.70 GHz 400 MHz 90 nm B1 2 MB 478 pin
    SL6FA  1.60 GHz 400 MHz 0.13 micron B1 1 MB 478 pin
    SL6F7  1.60 GHz 400 MHz 0.13 micron B1 1 MB 479 pin 
    SL86G  1.60 GHz 533 MHz 90 nm C0 2 MB 478 pin
    SL86M  1.60 GHz 533 MHz 90 nm C0 2 MB 479 pin 
    SL7EG  1.60 GHz 400 MHz 90 nm B1 2 MB 478 pin
    SL8QF  1.60 GHz 400 MHz 90 nm C0 2 MB 479 pin 
    SL6F6  1.50 GHz 400 MHz 0.13 micron B1 1 MB 479 pin 
    SL6F9  1.50 GHz 400 MHz 0.13 micron B1 1 MB 478 pin
    SL7GL  1.50 GHz 400 MHz 90 nm B1 2 MB 478 pin
    SL6F8  1.40 GHz 400 MHz 0.13 micron B1 1 MB 478 pin
    SL6F5  1.40 GHz 400 MHz 0.13 micron B1 1 MB 479 pin 
    SL7F3  1.40 GHz 400 MHz 90 nm B1 2 MB 479 pin 
    SL6N4  1.30 GHz 400 MHz 0.13 micron B1 1 MB 478 pin
    SL6N8  1.30 GHz 400 MHz 0.13 micron B1 1 MB 479 pin 
    SL6NB  1.20 GHz 400 MHz 0.13 micron B1 1 MB 479 pin 
    SL6NC  1.10 GHz 400 MHz 0.13 micron B1 1 MB 479 pin 
    SL7F4  1.10 GHz 400 MHz 90 nm B1 2 MB 479 pin 
    SL6NJ  900 MHz 400 MHz 0.13 micron B1 1 MB 479 pin 

  • HT4972 I am using iphone 3g and it is having currently IOS 4.1 version,till what IOS version can i upgrade ? please help me many of my apps are not working esp whatsapp.

    am using iphone 3g and it is having currently IOS 4.1 version,till what IOS version can i upgrade ? please help me many of my apps are not working esp whatsapp.

    iOS 4.2.1 is the latest version of iOS for the 3G.
    Facebook and Whatsapp both require 4.3 or higher.
    If you want to use those apps, either use the old version that should be in your iTunes library or upgrade the hardware to a 3GS or newer device.

  • F4 help on Parameter for ddic domain does not work

    Hello,
    I try:
    Parameters:  pa_waers TYPE WAERS.
    WAERS is a ddic data element for currencies and also a  domain with this name exists. The domain WAERS has a check table TCURC.
    When I press F4 for my field PA_WAERS in the Selection Screen, I assume a value help from the check table TCURC.
    I activated and re-generated my coding (as mentioned in the ABAP-Keyword help for "PARAMETERS") but it still does not work.
    Does anybody has a clue why this does this not work.
    The same thing is for a parameter:
    Parameters ..... type CTU_MODE.
    Domain CTU_MODE has value Fields (A, E, B) but also here on my program no F4 help occurs.
    Thanks in advance
    Stefan Berger

    A value table is assigned to a domain.  It becomes a check table when a foreign key relationship is established for a field in a table.  The field uses the data element and the data element uses the domain.
    For example, if you try:
    PARAMETERS: PA_WAERS TYPE EKKO-WAERS.
    You will get the F4 help you are looking for.  If you use tran SE11 and view EKKO, find field WAERS, use tab Entry Help/check and you will see that table TCURC has been established as a check table.  You can use the foreign key button to see the relationship that has been established between EKKO and TCURC.
    Also, domains cannot be used to type a field.  Your reference to CTU_MODE must be referring to a Data Element.  I tried this in a 4.7 system and the F4 works for me.  What version are you using?

  • Please help me. My YouTube app will not work. Every time I open it says 'cannot connect to youtube'. I have searched for help and tried resetting my settings and rebooting my ipad2 but nothing has solved the issue.

    Please help me. My YouTube app will not work. Every time I open it says 'cannot connect to youtube'. I have searched for help and tried resetting my settings and rebooting my ipad2 but nothing has solved the issue.

    Yes, I am connected to the Internet through my wifi. Everything is working fine with the e  eption of youtube.  I have reset all Internet settings and have tried synching to iTunes followed by rebooting.  This is all the advice I have found although none of it has been helpful.
    Has anyone else encountered this problem?

  • Satellite U300-151 - SD card slot not working

    I have the following model Toshiba Satellite (U300-151 PSU30E-074017AR ) the
    SD card slot not working I install windows XP SP 3 ,& the driver is installed 100% , I need to solve this problem ...
    plz chk this link:

    Hello
    I think on your notebook are missing some drivers.
    The SM Bus Controller driver is in the chipset driver package. So try to install it and maybe it works.
    The drivers you can find on the Toshiba website.
    Have you installed it with a Microsoft disk? The Toshiba recovery disk creator contains all necessary drivers and tools that you need and so this would be maybe an option for you to reinstall the OS.
    Greets

  • Privacy settings STILL not working - sort it out s...

    i always have my privacy settings fixed so that all options are set to "contacts" only.  however i am STILL getting messages from random strangers saying that i appear interesting.
    i'm not interesting. i have no interest in receiving these messages.  i have updated my software and rechecked all the privacy settings but i still get these messages.
    skype - can you PLEASE sort this out because it's getting so i don't even want to log in.  it's SO ANNOYING!!!!!
    i'm running on a mac (lion) - updating doesn't help. any other ideas? frankly at the moment i don't see why skype even bothers to have security settings - this is not the first time (by any means) that this has happened: they shouldn't make these kind of settings promises if they can't keep them.

    jordankees wrote:
    I am having the same issue.  I've gotten over 200 abusive IMs and random people calling me.  I have had Skype for years and I have never had an issue with my security.  I only have a smallamount of select contacts and I have never allowed people that are not on my contact list to contact me.  Please help me fix this.  It is getting out of control and I now have more than200 people blocked. I tried the whole changing my online status thing and it appears to have worked, but I am still skeptical.  I dont know how this happend and now I am worried that my information is out there somehow for the world to see.  
    If/when you have this issue, doing this http://community.skype.com/t5/Security-Privacy-Trust-and/privacy-settings-STILL-not-working-sort-it-... will fix the problem.
    About Me You can also use a IP Camera as your camera for Skype video Example Instructions

  • Primary PCI-E slot NOT functioning, Secondary does ? ? ? ?

    ....have & been running this MB:  MSI K8N Diamond Plus = SLi  w/2x_Nvidia G-Force7800GTX{512mb}..........came to turn on this morning and NO BOOT after post????? . . . . . .  have troubleshoot down as far as remove'd both VGA's and start'd with only one.........come to find out either card DOES work & boot's system up,  BUT ,  ONLY in the /Secondary PCI-E slot? !? !  This does not matter which card,  or even selecting in the BIOS of which slot first, ( aka: PCI-E1 > PCI-E2 / or / PCI-E2 > PCI-E2 ),  for it's bootable order...... SEEM's to be the Primary PCI-E slot, (closest to CPU),  is none functioning / reading any kind of video card install'd into? ! ? ! ? . . . . . wondering if anyone could shed anyony other help / suggestion's / comment's pertaining to this or any other idea's of which i may have NOT checked or try,  to troubleshoot .........  thnx in advance
    mr. Charles
    .

    Hi Charles
    Just wondering how you got on with the replacement? Did MSI give any details as to what might have happened or was wrong? 
    I'm having a similiar issue myself.  My MSI K8N SLI-F board seems to now have a 'tempremental" primary PCI-E slot.  I have a 9800GT card that was working fine for months and then I got no video on reboot after trying to get dual displays up and running.  After much troubleshooting and RMA'ing my 9800GT card I think it must be the slot on the Mainboard itself.  My 6800GS which has a light fan on it compared to the massive glaciator on my 9800GT is working fine but whenever I put the 9800GT (original or replacement) in I get no video on boot but I can hear the computer and HD making all its normal noises and know its getting to the windows login screen.  The 9800GT fan spins up then turns off or sometimes stays spinning.  Both cards work fine in another machine.  After cleaning out the slot and screwing in the card nice and hard it went again and ran all day but after shutting down and leaving it overnight, I got no video on boot again.  My guess is the cooling of the card overnight made it move slightly.  I have repeated the reseating steps and have it going again.  I can only presume the slot itself is now loose or the solder on it is failing or something, or could it be the Power Supply?....  has me stumped.  When the card isn't in just right and I get no video I also get both optical drives ticking / seeking like there looking for a disc about 10 times then the computer kinda internally restarts and it goes again with no video still.  When I have the card screwed in tight like now it doesn't happen.  With the card screwed in like now I pushed the card a little and then turned it on and again I get no video.  Reseat, rescrew and it goes again.... weird.   Any suggestions?  PCI-voltage?  PSU Maybe?  the slot?  something else?
    Anyway I don't think I can actually try the 2nd slot as the MSI K8N SLI-FI/ F site says:
    Two PCI Express x16 slot (supports PCI Express Bus specification v1.0a compliant)
    Normal mode Primary PCI-E slot is compatible with PCI Express x 16
    Secondary PCI-E slot is compatible with PCI Express x 1
    SLI mode Primary PCI-E slot is compatible with PCI Express x 8
    Secondary PCI-E slot is compatible with PCI Express x 8
    So I presume I can't get full 16x out of the 2nd slot and looking at it, it only has the gold pins going half way down the slot where as the primary slot has them right to the end.
    MSI K8N SLI-F  //  2 x 1gb PQI RAM  // AMD X2 4400+ (939)
    Silverstone OP650w PSU  // 2 x Optical drives  // 1 x 320gb Seagate SATA drive
    Asus 9800GT  //   PCI:  Soundblaster Audigy  // LeadTek WinFast Deluxe TVCard
    Matt

  • 915GM Speedster-FA4

    i have not purchased this motherboard but i am buying a new pcie card and i dont want to upgrade my current Pentium 4 (socket 478) to a new one and this was the ONLY s478 pci express motherboard that i could find.  So i am wondering if my P4 will work with it because under supported processors it says " Supports Intel® Pentium® M Dothan/Celeron® M Dothan processors in 478-pin package ". Does that include my processor? And also the only place i could find this board sold ONLY the board and not the driver cds and cable etc so when i tried to find a driver download i was unsuccessful as well so if someone could point me in the right direction i would really appreciate it. Thanks
    Dom

    Quote
    ...so basically, this board will NOT work with my processor?...
    You are correct, your proc is not supported.
    Quote
    ...Where can i get a board that does i have looked everywhere. Thanks for the reply.
    Here are the boards that support P4 478 procs, none of which support PCI-e.  I am not aware of any PCI-e board that supports P4 478 procs.

  • SIM 1 slot not working on A6000 plus

    Hi, The SIM 1 slot on my Lenovo A6000 plus is not working. I tried changing the sim positions, but somehow it does not show any network for the sim card placed in slot 1. Please advise what needs to be done. I have tried reboot and replacing sim slots for two providers that I use, but does not help. Chetan

    Thanks. When I checked, Firmware is on 150515 version. I am not sure about how factory reset is done? Can you suggest the steps to same as I am a bit skeptical doing it. Chetan

Maybe you are looking for