Help a noob with 2912 software image question

Hi guys, I have a few noob questions I hope you can help me with.
For study purposes I purchased a WS-C2912-XL-EN switch off of ebay and expected it to have the Enterprise software on it. the "EN" in the model number stands for enterprise does it not?
IOS (tm) C2900XL Software (C2900XL-H2-M), Version 11.2(8.5)SA6, MAINTENANCE INTERIM SOFTWARE
System image file is "flash:c2900XL-h2-mz-112.8.5-SA6.bin"
Processor is running Standard Edition Software
I have a WS-C2924C-XL-EN in my posession that is running:
IOS (tm) C2900XL Software (C2900XL-C3H2S-M), Version 12.0(5)WC8, RELEASE SOFTWARE (fc1)
System image file is "flash:c2900xl-c3h2s-mz.120-5.WC8.bin"
Processor is running Enterprise Edition Software
I want to practice setting up trunks and this is why I bought this particular switch so I need the enterprise version.
If the upload the enterprise image from the 2924 to the 2912 will it run?
I don't have access to the Cisco software tool to find out if this image is compatable with the 2912.
Would I be breaking any licensing rules by doing this? The switch was supposed to come with the enterprise software was it not?

Thanks for the reply. I went ahead & copied the IOS enterprise version image from the 2924 and tftped it onto the 2912, removed the old ios and set the boot image.
I rebooted and all is well.
One question; typically a tar would have been uploaded to the switch to update it and deliver the .bin and html files.
I only upgraded the .bin image and am going to use the same html files that were present to manage it through the web interface. Does using the old html files with a new image present a problem??

Similar Messages

Help a noob with his first mac

Ok, first let me say hello as this is my first post on this forum. second, let me state my problem.
I recently bought a G3 from a computer group at my college. I currently have it hooked up and am trying to get it to boot from an ubuntu disk (is positive it is the right version) because its free and i'm a poor college kid. however, rather than booting, at startup all i get is a gray screen with a folder in the center with an alternating picasso face and question mark. i've been told it's a broken hard drive stopping it from booting and reading the disk and i've been told that the hard drive shouldnt matter and it should boot anyway. Can anyone please help me with this? i have about 24 hours before my monitor gets taken and i cant mess with it anymore (borrowed it). thanks a bunch.

You get the blinking question mark when your Mac cannot find:
The preferred software type
in the preferred version
on the preferred Startup Disk
All of these parameters are stored in parameter RAM (PRAM) and maintained across power outages caused by blackouts OR moving OR maintenance by a 3.6 Volt battery half the length of AA battery located on the motherboard.
To reset the parameters to their factory defaults, open the side door (there is no interlock switch) find the tiny button flat on the board nearest the battery, press and hold for a quarter minute, wait at least five seconds more, then try to start normally. Avoid momentary presses.
You should seriously consider replacing this battery, and until you do, every time power is interrupted -- including the time when you actually replace the battery -- you will have to perform this little ceremony.
To boot from a CD -- provided it is in fact a bootable Mac CD -- hold down the c key immediately at startup. Many Ubuntu users have discovered what they though was a bootable Mac CD turned out to be a perfectly good installer, but was not Mac bootable.
Message was edited by: Grant Bennet-Alder

Help a noob with a parse error. Completely new to Flex, doesn't know anything.

Hi. I am completely new to Flex (and mxml and ActionScript) and have a silly little error right off the bat. I haven't written a line of code yet, and got the source files from a collegue (who is currently unavailable to help me out here) that obviously had this working before he gave it to me.
I am getting a parse error with the following lines. From my experience with PHP, I have a general idea that a parse error is usually a syntax thing, like a missing semicolon or something along that line. I've already tried semicolons in a bunch of places, but nothing seems to work. Any help would be appreciated. The X is where the program highlights the error.
<?xml version="1.0" encoding="utf-8"?>

<mx:Application xmlns:mx="http://www.adobe.com/2006/mxml" layout="absolute" xmlns:tg = "EditableTextGrid.*" xmlns:ns1="com.testURL.commonClasses.grid.*" viewSourceURL="srcview/index.html"
X verticalAlign="middle" implements="EditableTextGrid.ETGParent" >
initialize= "setLogin('testUser'); loadMatrix('module=portal&mode=i&searchString=1111')"

<mx:Style source="styles/AcctRequest.css"/>
Severity and Description
Path
Resource
Location
Creation Time
Id
Parse error at '\n initialize= \"setLogin(\'ngorelik\'); loadMatrix(\'module=portal&mode=i&searchString=1111\')\"\n\n\t'.
CV/src
contactsSWF.mxml
line 4
1319810874686
130
Other info: it was actually written with Flex 3.2 SDK

You are missing a quote at the end of your "setLogin(testUser)" function and you don't have that inside a tag (it's outside the greater than sign...
You have:
<mx:Application xmlns:mx="http://www.adobe.com/2006/mxml" layout="absolute" xmlns:tg = "EditableTextGrid.*" xmlns:ns1="com.testURL.commonClasses.grid.*" viewSourceURL="srcview/index.html"
X verticalAlign="middle" implements="EditableTextGrid.ETGParent" >
initialize= "setLogin('testUser'); loadMatrix('module=portal&mode=i&searchString=1111')"
It should be:
<mx:Application xmlns:mx="http://www.adobe.com/2006/mxml" layout="absolute" xmlns:tg = "EditableTextGrid.*" xmlns:ns1="com.testURL.commonClasses.grid.*" viewSourceURL="srcview/index.html"
X verticalAlign="middle" implements="EditableTextGrid.ETGParent" initialize= "{setLogin(testUser)}"...>

Help this noobie with his K8N Neo2 Please!!

Well uhh, I tried booting up the computer I built, but the monitor won't turn on. I tried resetting the CMOS header, all the way to the bare system. My PSU used to be the Thermatake Purepower 480w, but it died on me, so I had to get the Aspire 500w PSU instead. You think that will fix the problem? Because the TT PSU had 18 amps, while now aspire is going to give off 34 amps.
Specs:
9 fans (5 LED fans)
Thermaltake Venus 12 HSF
WD 74 GB raptor HDD
Maxtor 80 GB IDE HDD
1 gig Crucial Ballistix PC3200
AMD 64 3500+ Skt 939
MSI K8N Neo2 Platinum
XFX GeForce 6800
Mitsumi Floppy Drive
Nec 8X DVD-RW Opitcal Drive
Now I did a check on it, and it says I need a maximum of 346 watts (PSU calculator thing). Do you think it will turn my monitor on and make it work?
My DLED is 1=Orange 2=Red 3=REd 4=Orange
I looked around, and found one topic similar, but it doesn't help...

It should power it up easily if it gives 34A on the +12v rail. Let us know what happens, I can't see any obvious problems with the kit you've listed

Help a noob with slow dbs

oracle 10g, unix, 2gb memory - new to unix too so don't really know what other stats you guys need.
i exp and imp 9i database to 10g.
from 10g, i cloned a bunch of them, TECH1,TECH2....
at any one time, there will be 5 running at the same time.
sometimes, it gets reallly slow on some.
here is a sample startup info from one.
Total System Global Area 239075328 bytes
Fixed Size 1218700 bytes
Variable Size 75499380 bytes
Database Buffers 155189248 bytes
Redo Buffers 7168000 bytes
Database mounted.
Database opened.
Do you guys see anything that screams at you why it could be slow?
thanks a lot!

heres the pfile that the above uses
processes=150
sga_target=608174080
db_block_size=8192
compatible=10.2.0.1.0
log_archive_format=arch_%t_%s_%r.arc
db_file_multiblock_read_count=16
undo_management=AUTO
undo_tablespace=UNDOTBS1
remote_login_passwordfile=EXCLUSIVE
job_queue_processes=10
open_cursors=300
pga_aggregate_target=201326592
#control_files=("/u01/app/oracle/product/10.2.0/db_1/dbs/PROD7_141/RESTORED_CONTROL_FILE")
#db_name=DEVL7
instance_name=PROD7
service_names=PROD7.mycompany.COM
background_dump_dest=/u01/app/oracle/admin/PROD7/bdump
core_dump_dest=/u01/app/oracle/admin/PROD7/cdump
user_dump_dest=/u01/app/oracle/admin/PROD7/udump
#db_unique_name=PROD7
db_domain=mycompany.COM
db_name=PROD7
control_files='/u01/oradata/PROD7/control01.ctl','/u01/oradata/PROD7/control02.ctl','/u01/oradata/PROD7/control03.ctl'
Message was edited by:
ninteck

CSS11501 Upgrade Problem - can't remove software image

Hi,
We have a CSS11501 which came pre-installed with software version 7.20 (Build 206).
I wanted to upgrade this to version 7.40, so our supplier sent us a CD with the software image.
The install failed, because the supplier sent us the wrong image (ap0500037s.adi).
They then sent us another cd, with the correct image (sg0740004.adi-gz) ...
... however, I couldn't upgrade to this version, because the system now has two software images (the original 7.20 and the ap0500037s.adi).
When I try to remove the incorrect image, the CSS says that it doesn't exist.
When I try to install an image, it says I have to remove one of the other images first.
I don't really want to have to remove 7.20, just in case I have to roll-back for some reason.
Any ideas?

Gilles,
I went into offdm, but the same thing happened.
I selected the option to delete an image, but there was only one image listed, and that was the currently working one (which I really want to keep, in case I need to roll-back).
When I use the upgrade command, it says 'you have to remove one of the images, would you like to delete ap0500037s.adi?' I select yes, but it won't delete.
Are there any alternatives to formatting the disk?
Thanks,
Paul.

I think I need help with driver (software) settings for D110a

I think I need help with driver (software) settings for D110a all-in-one
Product: D110a all-in-one
OS: Windows XP Professional
Error messages: None
Changes before problem appeared: None--new installation
The quality of photo images (mostly JPG files) in printouts is awful even though the files display beautifully on the PC screen. I am using
IrfanView software for displaying/printing. As far as I can tell, IrfanView is not the problem.
When I print the same images on a Deskjet 5150 attached to a different PC also running XP Pro and IrfanView, the quality of the printouts is at
least acceptable, Some would probably say good or very good.
It's dificult to explain in words the problem with the printouts. A picture of really pretty vegetables (squashes, tomatoes, watermelon, etc) comes
out much too red. Moreover, the red, which appears shaded on the screen, seems to be all one shade in the D110a printouts.
Something similar happens to a view of a huge tree in full leaf. On screen, there are subtle variations in the "greenness" of the leaves. In the
printout, all green is the same shade. In the same printout, the trunk of the tree is all a single shade of grey. It isn;t even obvious that the
trunk is a round, solid object.
I liken the effect to audio that disappears entirely when you lower the volume and gets clipped into square waves in even moderately loud passages.
I don't know whether the D110a driver software permits adjusting the parameters that appear to be set incorrectly, and if adjustments are possible,
how I would identify which parameters to adjust, how I would access them, or how I would adjust them. I'm hoping that someone can help. Thanks.
I forgot to mention that I have used the diagnostic application and it tells me that there are no problems.
e-mail me at [email protected]

brazzmonkey wrote:
Hi everyone,
I noticed the following message when network starts on my gateway
Warning: This functionality is deprecated.
Please refer to /etc/rc.conf on how to define a single wired
connection, or use a utility such as netcfg.
Then I realized the way network settings should be written in rc.conf has changed. But I can't figure out how this should be done.
Currently, my set up is the following (old way):
INTERFACES=(eth0 eth1)
eth0="dhcp"
eth1="eth1 192.168.0.10 netmask 255.255.255.0 broadcast 192.168.0.255"
ROUTES=(!gateway)
eth0 is on DHCP because the IP is dynamically assigned my ISP.
eth1 has a fix IP because it's on the LAN side.
No problem to use DHCP on eth0 with the new settings.
But for eth1, I don't know what I am supposed to write for gateway.
Wiki isn't clear on that one either, and it looks like many articles still refer to the old way.
Any guidance appreciated, thanks.
brazzmonkey,
you can't define 2 interfaces the old way (even though I saw some tricky workaround somewhere in the forums).
Use, f.e., netcfg:
Comment your old lines.
In /etc/rc.conf insert:
NETWORKS=(Eth0-dhcp Eth1-static)
DAEMONS=(..... !network @net-profiles ....)
In /etc/network.d create 2 files:
First one is named Eth0-dhcp.
Contents:
CONNECTION="ethernet"
DESCRIPTION="Whatever text"
INTERFACE=eth0
HOSTNAME="your hostname"
IP="dhcp"
DHCP_TIMEOUT=15
Second one is named Eth1-static.
Contents:
CONNECTION='ethernet'
DESCRIPTION='whatver'
INTERFACE='eth1'
HOSTNAME='hname'
IP='static'
ADDR='192.168.0.10'
GATEWAY='192.168.0.1' # your gateway IP
DNS=('192.168.0.1') # your DNS server
The names Eth0-dhcp and Eth1-static are not magic. They just must be the same in rc.conf and in /etc/network.d.
Hope it helps.
mektub
PS: netcfg must be installed.
Last edited by Mektub (2011-07-20 14:07:05)

Help! My display driver is no longer compatible with Adobe software!

Help! I rely on Adobe CC and my iMac to earn my living. My display driver is no longer compatible with Adobe software! What should I do? (most affordably because I dont have enough money for even basic living expenses right now.) Detailed notes are below but in a nutshell, I have a NVIDIA GeForce 8800 GS display driver. Adobe no longer supports it and disables the software functions depending on the graphics hardware. It recommends I check the manufacturer's website for the latest software. I did but only found firmware update for a different type of display driver for my early 2008 iMac. What should I do??! Please help me solve this!
Note from Adobe:
http://helpx.adobe.com/photoshop/kb/photoshop-cs6-gpu-faq1.html
Adobe: “Note: AMD/ATI 1000, 2000, 3000, 4000 series, nVidia GeForce 7000, 8000, 9000, 100, 200, 300 series and Intel HD Graphics (First generation) cards/GPUs are no longer being tested and are not officially supported in Photoshop CC and CC 2014. Some GL functionality is available for these cards, but it's possible that newer features don't work.”
I have an early 2008 iMac:
Hardware Overview:
Model Name: iMac
Model Identifier: iMac8,1
Processor Name: Intel Core 2 Duo
Processor Speed: 3.06 GHz
Number of Processors: 1
Total Number of Cores: 2
L2 Cache: 6 MB
Memory: 4 GB
Bus Speed: 1.07 GHz
Boot ROM Version: IM81.00C1.B00
SMC Version (system): 1.30f1
Serial Number (system): YD*****N4
Hardware UUID: D42002AC-A757-51C0-8D5D-333AD24D3DF9
My display driver:
NVIDIA GeForce 8800 GS:
Chipset Model: NVIDIA GeForce 8800 GS
Type: GPU
Bus: PCIe
PCIe Lane Width: x16
VRAM (Total): 512 MB
Vendor: NVIDIA (0x10de)
Device ID: 0x0609
Revision ID: 0x00a2
ROM Revision: 3234
Displays:
iMac:
Display Type: LCD
Resolution: 1920 x 1200
Pixel Depth: 32-Bit Color (ARGB8888)
Main Display: Yes
Mirror: Off
Online: Yes
Built-In: Yes
Note from Adobe:
http://helpx.adobe.com/photoshop/kb/photoshop-cs6-gpu-faq1.html
Adobe: “Note: AMD/ATI 1000, 2000, 3000, 4000 series, nVidia GeForce 7000, 8000, 9000, 100, 200, 300 series and Intel HD Graphics (First generation) cards/GPUs are no longer being tested and are not officially supported in Photoshop CC and CC 2014. Some GL functionality is available for these cards, but it's possible that newer features don't work.”
<edited by host>

If you decide to use up to the minute applications, you will have to accept that the computer and operating system will eventually be incompatible with your chosen application as the features in the latest application rely on new hardware and operating systems to support them.
Your options are to either use a newer Mac or use a version of Photoshop that will run on your Mac.

HT201210 I tried to do an update to the Ios 5 but it failed tried to restore my iphone however all im left with is an image of itunes with a usb connector please help as my phone will no longer work!!

Hi I tried to do an update on my Iphone 4 hardware but it failed (dont knoyw why) I followed instructions to restore my Iphone unfortunatel all im left with is an image of itunes with a usb and a dead phone can someone help???

Hey, I aggree with Tempelton for the most part, but if you are an advanced user on the computer on the phone, there is one thing you can try. There is a program called RecBoot, which might help you, and here is a page that might help you. http://jaxov.com/2010/05/recboot-iphone-recovery-mode/ If you are not an advanced user, I would NOT recomend using RecBoot, and just proceeding with the restore. A little consolation could be that you probably had Photo Stream on, and you might have been backing up to iCloud, which should mean you'll have some stuff after the resote. Sorry this happened!

How do i make a still image (photo) fit the length of the music? I record music and want to put the tracks to a video file with a still image of my business logo in the background. Any help?

How do I make a still image (photo) fit the length of the music? I record music and want to convert the tracks to a video file with a still image of my business logo in the background. On windows movie maker you could just select "fit to music" but this program isnt as easy to figure out! Any help?

Double-click on the still image in the project timeline to open the Inspector. In the Inspector, adjust the duration by typing in a new duration to match the length of your music. I think the limit for a still image is 10 minutes. If you need more than this, simply drag the image into the timeline again then adjust its duration. The two images will play seamlessly (no gap will be visible).
See this iMovie Help topic:
http://help.apple.com/imovie/#mov3a883915
You can achieve more precision when entering durations by changing a preference in the menu item iMovie Preferences. Check (tick) the preference for Show Time As HH:MM:SS:frames. This will enable you to enter the duration of stills down to the frame level, rather than full seconds (NTSC is 30 frames per second; PAL is 25 fps). When entering times, type a colon between each time segment, such as 2:50:15, which represents 2 minutes 50 seconds and 15 frames. For 5 seconds 20 frames you would enter 5:20 and so forth.
Note that the music will only run to the length of the video in the timeline (in your case, the still images). So, after increasing the stills duration you will need to drag the end of the music track as far as required. The stills can be dragged inwards to reduce the duration if necessary.
John
Message was edited by: John Cogdell - added Note

I have to make a catalouge for my services as a financial planner.. earlier i used to do in MS publisher.. now i have a mac book.. can some one help me with some software info with which i can design a catalogue??

I have to make a catalouge for my services as a financial planner.. earlier i used to do in MS publisher.. now i have a mac book.. can some one help me with some software info with which i can design a catalogue??

Depending on what your needs are, you may use Pages included in iWork or purchase it separately (usually there is an evaluation copy with any new mac, I guess) or try other publishing apps. I once used MS Publisher, I remember it was something like a more sophisticated word processor, right?
You may try the cheaper DTP iCalamus or Word for mac.

I need help with Changing my Security Questions, I have forgotten them.

Its simple, I tried buying a Gym Buddy Application and I had to answer my security questions... Which I have forgotten I made this a while ago so I probably entered something stupid and fast to make I really regert it now. When i'm coming to this...

Hello Adrian,
The steps in the articles below will guide you in setting up your rescue email address and resetting your security questions:
Rescue email address and how to reset Apple ID security questions
http://support.apple.com/kb/HT5312
Apple ID: All about Apple ID security questions
http://support.apple.com/kb/HT5665
If you continue to have issues, please contact our Account Security Team as outlined in this article for assistance with resetting the security questions:
Apple ID: Contacting Apple for help with Apple ID account security
http://support.apple.com/kb/HT5699
Thank you for using Apple Support Communities.
Best,
Sheila M.

I have misplaced my iPod Touch 4th Generation. According to Find my iPhone, it should show up in offline mode. I need help on locating it with a software or some other way. Help?

I have misplaced my iPod Touch 4th Generation. According to Find my iPhone, it should show up in offline mode. I need help on locating it with a software or some other way. Help?

There is no other way.
Sorry

Help I Have A Problem With Nokia Software Updater

Hi
I have This Problem With My Software
Please Show Me any Way To Fix it
Note 1*:I Used This Software on thisComputer but when i chang my windows it doesnt work
Note 2*:after that when i used software (once time) it didnt work because of that i changed my windows
Attachments:
1.JPG ‏24 KB

first its ok
then
translation:
For a better connection please insert the usb-cable directly in to the computer and not trough a usb-hub or -keybord or a dockingstation of a laptop.
Nokia Software Updater has tried downloading the software, but this is failed 4 times.
Its posible that it can be caused by a bad, slow or instable internet connection.
This failure can also occur because we have maybe a problem with our servers.
try later again
i tried it on 2 PCs one with vista and one with XP plz help me
Message Edited by progunnl on 13-Mar-2009 02:50 PM

Help with CS4 tabbed image mode?

How does one drag a layer from one image to another in tabbed mode?
I'm forcing myself to work with the tabbed image interface as I assume someone thought this new feature was a good idea.
I often drag or shift+drag layers from one image to another, whether it be adjustments or image elements that need to be placed (in register) as a layer in another open image.
But when I use the tabbed interface mode any attempt to drag a layer from one tab to another does not work.
What am I missing???
Thanks
Russell

Yeah I noticed the same limitation.. they making floating document mode extra ****(UI interface that doesn't adhere to System OS visual style, documents that no longer move with the main PS UI, like when you adjust the mainframe size or move the window floating docs would get moved and stay within the UI, unless you dragged and floating doc outside the main ui frame, which was good, but now it seems floating docs always live outside the mainframe and appear above docked although open panel UIs.. not to mention the new theme looks like complete and utter dogshit.. but oh well.. CS5 might get some more work.. maybe they'll bring back the pallete well.. ******* adobe noobs.
I too liked to drag & drop of layer objects onto another document its common thing I do when working in photoshop.. I just can't believe how lame Adobe are that they couldn't allow this functionality seeing as a tabbed UI is the default setup now..
seems like the only way around it is to use the now **** floating document mode... or use one of the splitview modes.. course those are crap, but at least you can D&D layer objects, and then switch back the single doc tab.
lets not get into the flakey **** opengl support and functionality.

Help a noob with 2912 software image question

Similar Messages

Maybe you are looking for