HELP! Can't connect on 2 or more wireless connection

I have WRT110 Linksys wireless router. I also have the latest firmware. fw 1.0.04. I have no problems connecting wired connections(2 PCs) and 1 wireless connection. However, when i tried connecting 2 or more wireless connections(3 laptops). All computers gets disconnected. I need to turn off the router again and my computers to get connected but only 2 PCs and 1 wireless laptop... Any help please! I already talked to tech support and no help! We tried to power cycle, reset for 30 secs, remove adapter, cables, etc. and didn't help! Same results! Can't connect on 2 or more wireless connections. We edited the basic wireless setting to WEP/WPA personal, band, channels, still no luck too! Im getting frustrated with this router. PLEASE HELP! I have Time Warner Road Runner cable internet. Thanks in advance!
Message Edited by rhenzhen on 10-02-2008 05:18 AM

Try these settings on Advanced Wireless
settings>>Change the Beacon Interval to 75 >>Change the Fragmentation
Threshold to 2304 Change the RTS Threshold to 2304. and Upload the same firmware on the router once again.

Similar Messages

Valet M20 - Connecting another Valet Plus for more wireless connections

Can you hook up on Valet Plus to another Valet Plus for more wireless connections?

Like UnknownHero has asked, how many devices do you intend to connect? A single Valet Plus shouldn’t have trouble handling a normal home network which laptops, wifi phones, media players, DVRs etc.
But to answer your question, yes, it is possible.

Help, can't open project file any more

I relaunched iMovie to refresh the iPhoto thumbnails and now my project can't be opened. It is not listed at all in the Project list inside iMovie. And when I try launching it from the Finder, it open iMovie but nothing happens. Not even an error message.

I have not heard back so I am not sure if I referenced the thread correctly when i last sent the muse file. I used the url https://forums.adobe.com/message/7212679 but I see in this email below it is referred to as https://forums.adobe.com/message/7213601#7213601
I attached it as a zip archive in my last email. I have also posted it to dropbox (unzipped) at https://www.dropbox.com/s/30vna0yqacvokvw/LKFdotcom%20v3.muse?dl=0
Any help would be greatly appreciated.
Thanks,
— David
David E. Frith | DEF Design
860.985.4471
[email protected]

How can I fix my MacBook Pro losing wireless connectivity with Epson Stylus NX625 printer. It will work once and then I get an error saying the printer is not connected.

I can connect to my Epson Stylus NX625 through my wireless network and print a page or two, but then the next time I go to print it says that the printer is not connected. Any fixes? I have tried deleting the printer and re-adding it to my MacBook Pro OS X version 10.9.4, but sometimes it doesn't even find it, and other times it says it is connected, but when I go to print it says not connected. Very frustrated. I have also installed the latest drivers, etc.
What now?

Your computer is going to run hot while playing CPU/GPU intensive games - it should heat up and the fans should be noticably loud. As to why it's 'crashing' - can you post a kernel panic log? You may have some third-party kexts that are causing the problems.
Clinton

Satellite C655D-S5533 can't connect to internet through ethernet (wireless connection ok)

I can't get an ethernet connection thru my ISP's (Comcast) internet cable box. I clicked the LAN icon on control panel but still can't connect.

First, reboot the Comcast box and then reboot the computer. If it still doesn't work, look in Device Manager under Network Adapters. If the LAN adapter shown there is Atheros, reinstall using THIS driver. If it says something else, post back. I'm assuming you are still using Windows 7 64 bit that came with the machine.
C.B.
Toshiba Sat. C75D-B7260 Win 8.1 64 Bit--Toshiba Sat. L775D-S7132 Win 7 HP SP1 64 Bit and Win 10 PRO Technical Preview--Toshiba Sat. L305-S5921 Win Vista SP2 32 Bit

Can't Connect to Linksys Admin over wireless connection

I just purchased a LinkSys WRT54GX2. Setting up the wireless network with my DSL modem was a breeze. However, I have one problem. I am only able to connect to the router admin from the computer that is connected by cable. My laptop can access the admin if connected by cable. However, when I have it connected wirelessly, it can't connect. Is there a particular setting I have forgotten?

They only recommend doing settings wired. Now, I have usually been able to do whatever I wanted wireless, but I consider that a bonus.

Macbook 2009 intermittently looses wireless connection, Macbook 2009 intermittently looses wireless connection

When I'm on the internet using the airport, I loose my connection all the time. The I don't loose the internet, it just like freezes and eventually it will come back and the action I have tried to get it to do, like go to another page or link etc. it will have done. I can still use the computer itself just not the internet. Crazy huh?
I have checked in troubleshooting and gone through the manual. I'm not finding an answer. I've checked with my Internet Service Provider, it's not them. Everyone else in my household is staying connected just fine. Is my airport card just going out and I'm out of luck until I replace it? I'm hoping maybe there is an upgrade or something that might help. If you have a suggestion please let me know.
Thanks

Solution may be found if you search in the "More Like This" section over in the right column.

How to connect a printer to a wireless connection using airport/time capsule

How do you connect a Cannon MP620 printer to the wireless network with my time capsule/airport? It was set up before but I've had to redo all the settings with a new Time Capsule and now the printer isn't working. Can't remember how I set it up before. Didn't seem that hard back then.
Thanks!

So you plugedd the printer into the time capsule usb right?
You need to re-add the printer in the system preferences one more time because the location has moved.

Problem connecting laptop to printer via wireless connection

I installed my HP Photosmart D110 series and the printer is not detecting my wireless internet (which is a Verizon Wireless card) . I only know the basics when it comes to computers, internet, etc. Therefore, this might be a completely stupid question, but is it possible to connect only through my Verizon card or do I need to purchase a router as well?
When I print my Wireless Network Test Report from my printer it tells me that it's recommended to change my network name to make it unique? I have no idea how to do this. And is it even applicable here?
I would greatly appreciate some feedback here.Thank you!

OK,
1. On the printer: Setup > Network > Reset network Defaults
2. On your PC, go to Start > Control Panel > Network and Sharing Center. Look for a wireless network that starts with 'hp" or "HP". Join it. There is no password. On the printer: Setup > Network > WIreless Network Test.
3. Now, in Start > Control Panel > Printers, Click the Add a printer
4. Select Local printer
5. Select Create a new port and select Standard TCP/IP Port and click Next button.
6. Under Device type, select TCP/IP Device. Under Hostname or IP address, enter the printer's host name (found on the printer's network configuration report the generated above). Click Next.
If you get a message about Additional Port Information Required, then the printer was not found using the host name. You can go back and retry or using the printer's IP address instead of the host name.
7. Select Hewlett-Packard from the list of manufacturers and select and select your printer model. Click Next.
If your printer model was not listed, then select Have Disk, browse the HP CD that came with your printer and select the first file that starts with hp and ends with inf. Click Open then OK. Select your printer model. Click Next.
8. If you are asked, use the currently installed driver.
9. It will ask for the Printer name -- enter a new name or use the existing one. This will be the name of the printer that you select from other applications.
10. You may be asked to share the printer. Make a choice and click Next.
11. The Print Test Page box appears. Go ahead and print it.
12. Click Finish.
Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
I am employed by HP

Wired connection thru TC FAST. Wireless connection VERY SLOW.

I have a Time Capsule (purchased in the Spring, so it 's the generation before the one that's out now), and 4 Airport Expresses. I'm also using a MegaPlug 85 Mbps Ethernet adapter kit. Whenever I turn off the airport card on my laptop and plug directly into either the MegaPlug or the Time Capsule, my connection is the fastest that it's ever been. Pages come up with barely any perceptible wait. When I unplug and use the Airport to connect over my wireless network, it's much, much slower.
I used the assistant tools to configure the Time Capsule and the Airport expresses. Are there any settings that I should manually change to improve my speed?
Is it possible that I have too many devices on the network? Currently, I have 3 Tivos that all use wireless to download programming information. We have an XBox connected to one Airport Express. Then we have 5 laptops -- 3 or 4 of which may be in use at any one time.
Also, our Internet provider is Comcast Cable in New Jersey.
Thanks for your help!
-Sue

silirap wrote:
I have a Time Capsule (purchased in the Spring, so it 's the generation before the one that's out now), and 4 Airport Expresses. I'm also using a MegaPlug 85 Mbps Ethernet adapter kit. Whenever I turn off the airport card on my laptop and plug directly into either the MegaPlug or the Time Capsule, my connection is the fastest that it's ever been. Pages come up with barely any perceptible wait. When I unplug and use the Airport to connect over my wireless network, it's much, much slower.
I used the assistant tools to configure the Time Capsule and the Airport expresses. Are there any settings that I should manually change to improve my speed?
Is it possible that I have too many devices on the network? Currently, I have 3 Tivos that all use wireless to download programming information. We have an XBox connected to one Airport Express. Then we have 5 laptops -- 3 or 4 of which may be in use at any one time.
That many AirPort Express units can cut your network performance all by themselves. Only one of them can transmit at a time. In addition, the extra relaying of traffic that the AirPort nodes have to pass among themselves cuts into the available bandwidth.
What model AirPort Express(s) do you have ("N"-capable or "pre-N")? That can make a difference in how you configure your network. Can you identify Wi-Fi band (B, G, or N) capabilities of each of your Wi-Fi clients? That might also make a difference in your options for improving your network. Are any of your non-laptop Wi-Fi clients close enough to an Wi-Fi node that you could connect them with an Ethernet cable?

"Unable to connect to hidden network" - Losing wireless connection on 1 PC in network - EA4500

We have a two-month old EA4500 router. Over the last couple of days one of our wireless pc's (running Windows 7) has occasionally been losing connection to our wireless network. Troubleshooting indicates that it is "unable to connect to the hidden network (our network name)" Our network should not be hidden, and our 2 other wireless devices are not experiencing this issue. When the disconnect occurs, the only way we are able to reconnect the PC is to disable and reenable the wireless adapter through device manager, or pull the adapter out of the USB and re-insert it. (The USB wireless adapter is also new - only a month old and is also a Linksys ). Does anyone have an idea what could be causing this issue, and what we can try to fix it? It's getting very annoying. Thanks!

There are times that these USB adapters (especially those Wireless Network Adapters) requires more power and they can't draw enough power once plugged in to a USB hub or USB extension cables. Can you try to plug it in directly to a USB port at the back of your computer? So that the adapter would draw enough power from the motherboard.
If everyone needs to believe in something, I believe I'll have another beer..

HELP PowerPC G4 OS 10.3.9 Unable to connect to base station after updates

OK...I have read many topics that seem to be related, but after trying all of the suggestions I could find, nothing is working....PLEASE HELP:)
I have a PowerPC G4 running OS 10.3.9 I completed the suggested software updates, and now I can not connect to the internet wirelessly. I keep getting the error message that my password is incorrect. This is not the case.
The software updates that I ran were for iTunes, Java, Airport(probably the problem) and security updates.
The current version of airport utility I am running is 4.2 is there anywhere I can download an older version? My wireless connection worked just fine before I updated.
Please, this is driving me CRAZY! If anyone has any ideas please post.

Hi,
We are running like units, with the same airport version 4.2.
Have you checked in "Keychain Access" for the password it is looking for? After updating mine once (a while back), the system reverted to the first one I had (but had changed since then).
To get to Keychain Access, us Finder and put Keychain Access in the upper right search box. When you get in, scroll down to the name of the network and click "Attributes". There in the lower left is "Show Password"... check it. It will now ask for your Admin/Keychain password (which will be the same if you have NOT made a separate Keychain password). Allow Once below the password entry. The password it wants will be below the box you checked to show it.
If you have changed it or have more then one by that name, it may be time to delete the older version(s) so keychain only has one to look for, not 2 or 3 like I had. If there is more then one, try all the passwords but remember MAC OX tunes out after some 3 tries, you will have to shut down and restart to get 3 more tries. Careful with deleting any till you find the right one, or the one it wants.
If these do not do the trick, let us know and we will try some other things...
Enjoy

Can't configure Wireless Connection to HP OfficeJet Pro L7780

I recently purchased both my iMac 24" 2.8GHz computer with OS x 10.5.2 and HP OfficeJet Pro L7780. I was able to use the HP setup CDs for my Windows laptops and configured them to use the printer in a wireless configuration.
The iMac is creating the headache (actually I think it's HP causing the headache). When I try to install HP's driver 9.7.1 using their utility, it is unable to detect the L7780 in a wireless configuration. The moment I connect via USB or wired Ethernet, the printer is detected without a problem. My printer is located @ 192.168.1.30, fixed IP address via a NetGear FSW308 switch. My iMac is fixed @ 192.168.1.100 and the gateway is 192.168.1.1
I spent hours on the phone with HP support and am still in the same spot... HP software won't find the printer when it is wireless. I can configure OS x 10.5.2 to use the internal L7700 series driver and put the IP address in the dialog box. The printer prints without issue using the OS printer drivers, but the other features such as scan and fax will not work without the HP software.
I can ping the printer and I can connect to the printer's EWS, but the HP software will not find the software.
Overall config: iMac wireless network connection to switch; Printer also wireless connection to switch.
So far HP is dumbfounded and all they can say is that I should call Apple because the printer software works fine when I connect the Ethernet or USB cables.
HELP!
Thanks,
Roland

Thank you for the thought. Yes, although my SSID is public, I have a WEP 128-bit security key. The printer, the iMac and my Windows laptops all connect to the wireless network without issue, as evidenced by my Windows laptops and iMac (if I use the driver included with OS X 10.5.2).
I can ping the printer from the iMac as well as connect to the printer's web interface, so connectivity exists. It is as if the setup software or the printer are trying to communicate using a port that or service that OS X may be blocking.
My OS X firewall is configured to accept all connections though... so that shouldn't be the issue unless there is a bug in accepting all connections.
Thanks,
Roland

Problem connecting Nokia C3 to home wireless route...

Good day, Nokia!
I recently bought a Nokia C3-00 WiFi phone but I can't seem to browse my home wireless connection with it. The phone can detect and connect with the wireless network successfully but when I open my mobile browser, it can't load websites, saying "Service not available."
However, I can connect and browse the internet through other WiFi hotspots, just not my home connection. The router I'm using is LP-8616. It's an AP router, if that helps. Unfortunately, there's no firmware upgrade for this router anymore.
I've read all the threads about this problem here and all over the internet but still nothing works for me. Hope you or somebody here could help me to finally solve this problem. More Power!

Allsolution from another post, see /t5/Cseries/C3-wifi-problem-connect-to-wlan-but-internet-not-work/m-p/950115#M14517. Found out how to solve the problem of connecting via WLAN in the following way (the phone was able to connect to the Internet only through the GSM provider network):
Step 1: Menu> Settings> Configuration> Personal Settings> Add> Web or Streaming or any other (Just add, needs no other settings)
Step 2: Menu> Settings> Configuration> Default config. settings (choose MyWeb, Personal Settings or the name created at step 1)
Step 3: Menu> Settings> Configuration> Personal settings (delete the field created in step 1) then go to Menu> Settings> Configuration> Preferred access point (choose one of the available options)
Now you can open your browser and try to connect. It should ask what method you choose (WLAN or Access Point Preferred)
If your phone does not want to be connected via the GSM provider network, the user can manually enter settings for defining an Access Point (Step 4)
Step 4: Menu> Settings> Configuration> Personal Settings> Add> Access Point (check with GSM provider for account settings)
Step 5: Menu> Settings> Configuration> Preferred access point (select the field you created earlier)
I know that what I wrote above may seem like science fiction for a user who is not accustomed to butoneasca phone and non-stop, but I assure you that the operation should take no longer than 5 minutes.

Wired and Wireless Connections to OfficeJet 8620?

We have a small wired Ethernet network. We are planning to install an HP OfficeJet 8620 multi-function printer tomorrow. I understand that for a wired-only Ethernet network, I would just connect the OfficeJet to our router, then install the drivers on each workstation.
Unfortunately, our situation is more complicated than that. Several people want to use wireless devices to print to the OfficeJet 8620. We have a working wireless network in place, and the wireless devices are able to access it without problem..
All devices on the network (wired and wireless) use the same router, which has both wired Ethernet ports and wireless capability. So, everything is on the same network, going through the same router.
From reading the 8620 documentation, it looks like you can only have a wired OR a wireless connection, but not both. Apparently connecting a CAT-5 cable to the Ethernet port on the printer disables the wireless capability of the printer.
If that is correct, what can we do to enable both wired computers and wireless mobile devices to print to the 8620, given the network structure I have described above?
Thanks very much for any assistance you can offer.
This question was solved.
View Solution.

Hi,
You can setup as shown on page #7 of tyhe following guide:
http://www.hp.com/ctg/Manual/c00389927.pdf
Regards.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

HELP! Can't connect on 2 or more wireless connection

Similar Messages

Maybe you are looking for