HELP!! Cisco RV180 Port Forwarding

Someone please advise as to this is the first time I've tried to setup port forwarding using the Cisco RV180 Router. I have a Cisco RV180 Router, a Ruckus 7055 access point and a power distribution unit. I'd like to be able to access the router remotely and also the devices behind the router (the ruckus access point and the power distribution unit). I'm assuming that I'll need to assign the Cisco RV180 router a static IP address and I'm assuing that this static address should be assigned to the WAN port? I'd also like to configure port forwarding so that I can access the ruckus and the PDU remotely also. I've tried assigning a static IP address to the WAN port of the RV180 but I cannot ping this device remotely. Anyone have any advice on accessing the RV180 remotely? I've populated all of the correct fields for the WAN settings (ip, gateway, subnet, etc.) , and my static ip address is valid.Thank you in advance.

Hello sirflex,
As you have mentioned you need to configure a static nat for the devices which you have done when you configure a port forwarding.
Have you configured access rules under firewall>access Rules. Add the access rules for the ping and the Http and Https services.
Can you capture the packets at the WAN port while you are pinging the WAN port and the firmware version on the device.
Which mode are you running the device gateway or router. You can check it under Netwroking>Routing>Routing Mode.
Thanks,
Prithvi
Please mark answered and rate for helpful posts.

Similar Messages

RV180 port forwarding issue

I wanted to forward a range of ports on a RV180, so I created a service for them, but when I go to the port forwarding page, it seems you have to enter an internal port number, which is a problem, because with a range you don't know what the incoming port was, and also you can't enter a range in the internal port field anyway. In the online help it mentions an option for this:
Forward to Port: Select Same as incoming port if the traffic
should be forwarded to the same port as of the incoming traffic or Specify
Port if the incoming traffic should be sent to one particular port.
Port Number: The port to which incoming traffic should be directed in
case specify port option is chosen.
But this option does not exist in the interface. There is only the internal port field. Surely this is an omission? If you can't forward a port range within a service you create, what's the point of allowing you to create it in the first place?

Hi Matthew,
With RV180 we can have port range forwarding to the LAN. (tested and working)
Please follow this steps :
1. Under Firewall --> Advanced Setting --> Custom Services
2. Add the range of port and choose the Protocol Type (please if you have already single port forwarding in the range port please remove them)
3. Under Firewall --> Access Rules --> add the following rules
4. From WAN to LAN, Action : Always allow, Service : your service, Source:Any, Dnat: Private Server IP, Status : Enable, SAVE
--> Now if we want to check you can go to port forwarding we will see the rule added automatically and in the internal port is EMPTY --> please don't edit the rule of port forwarding otherwhise the router will expect to put the internal address
--> If we want to test (if you have the Router in test envirement and you don't have the server connected in the local) please follow this steps to confirm our configuration
0. Please install wireshark (Packet sniffer)
1. Under Administration --> Diagnostics --> Packet Capture
2. Select LAN and start to capture the traffic
3. From Client outside try to access to access with public IP with different port already configured for Access rule (from the browser publicip:port)
4. Stop the packet captures and downloaded
5. Open it with Wireshark and filter by "tcp.port==xx" you will there is the request coming to the LAN it means the firewall allow those port (xx:port number)
Here is a screenshots from my test : (I redirect range of port 70-80 TCP) to internal IP 192.168.1.100
Please Rate this post or Marked as answered to help other Cisco Customers
Greetings
Mehdi

Please Help - Only Some Port Forwards Working

Hi all,
I have the most annoying issue with a Cisco 887VA-K9 port forwarding. Some port work while other don’t and I just can’t see why, however I suspect it is a zone based firewall (ZBF) issue.
Port forwards on the follow ports all work fine:
External port 8021 to 192.168.4.253 on port 80 works
External port 8022 to 192.168.4.253 on port 8022 works
All the rest don’t. I also have SIP phones sitting outside the LAN which are unable to register through the internet with the PBX unit which is in the DMZ network 192.168.4..0
Any help would be great appreciated as this sending me mad. Fully running config below.
Louise ;-)
Building configuration...
Current configuration : 36870 bytes
! Last configuration change at 12:49:03 Magadan Fri Nov 8 2013 by cpadmin
version 15.1
no service pad
service tcp-keepalives-in
service tcp-keepalives-out
service timestamps debug datetime msec localtime show-timezone
service timestamps log datetime msec localtime show-timezone
service password-encryption
service sequence-numbers
hostname QQQ_ADSL_Gateway
boot-start-marker
boot-end-marker
security authentication failure rate 3 log
security passwords min-length 6
logging buffered 64000
enable secret 4 gim.lMOdQK/21R4Wu.QJfOMAv3CIkRyN.hbSTG5xAxE
aaa new-model
aaa authentication login local_authen local
aaa authentication login ciscocp_vpn_xauth_ml_1 local
aaa authorization exec local_author local
aaa authorization network ciscocp_vpn_group_ml_1 local
aaa session-id common
memory-size iomem 10
clock timezone Magadan 11 0
crypto pki token default removal timeout 0
crypto pki trustpoint TP-self-signed-3471381936
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-3471381936
revocation-check none
rsakeypair TP-self-signed-3471381936
crypto pki trustpoint test_trustpoint_config_created_for_sdm
subject-name [email protected]
revocation-check crl
crypto pki certificate chain TP-self-signed-3471381936
certificate self-signed 01
3082022B 30820194 A0030201 02020101 300D0609 2A864886 F70D0101 05050030
31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274
69666963 6174652D 33343731 33383139 3336301E 170D3132 30373132 31313332
34375A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649
4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D33 34373133
38313933 3630819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281
8100AB76 5F7EE03F 306F52A0 91E82E04 7A69528D 1839409C 55BCC55A 47F180A9
7B522E9B FBB96A32 715178FE B96B737E 788947A4 CF4791AA 15609E37 A3F66F07
AD1B8A34 A2877711 E33A613D 8E50AE40 A106DE9C B2B03B95 73392ADB 4BB51FAD
6F2D6F8D A90BA0B5 BD1A209C F54126A9 2E2FF5B7 85041B7E C72032C0 CECE7F79
51550203 010001A3 53305130 0F060355 1D130101 FF040530 030101FF 301F0603
551D2304 18301680 141713AB B7F927E5 50C242DF 9912C3B6 61D93313 80301D06
03551D0E 04160414 1713ABB7 F927E550 C242DF99 12C3B661 D9331380 300D0609
2A864886 F70D0101 05050003 81810099 8EBE5630 2E6734A8 4D2FD0A5 F09A98F8
9E49125F AECEF4BB E0DEBB3A 1A449E38 99B02114 7EC84845 B53C2F88 046B7290
AE44967A 8BE20F5E 9D4A1CFC E1F64FE8 59F51892 23B88B4E 3416808A 68E65660
644C7DA0 E3A7A525 14FE8E54 67C35F8E CF69EB40 34DFB13D EA302F66 102C822A
3D7107BA AA4E7273 1D43690E C4A5D4
                quit
crypto pki certificate chain test_trustpoint_config_created_for_sdm
no ip source-route
ip dhcp excluded-address 192.168.0.230 192.168.0.255
ip dhcp excluded-address 192.168.0.1 192.168.0.200
ip dhcp pool QQQ_LAN
import all
network 192.168.0.0 255.255.255.0
default-router 192.168.0.254
dns-server 192.168.0.6 202.1.161.36
netbios-name-server 192.168.0.6
domain-name QQQ.Local
lease 3
ip cef
no ip bootp server
ip domain name QQQ.Local
ip name-server 192.168.0.6
ip name-server 202.1.161.37
ip name-server 202.1.161.36
ip inspect log drop-pkt
no ipv6 cef
parameter-map type inspect global
log dropped-packets enable
parameter-map type protocol-info yahoo-servers
server name scs.msg.yahoo.com
server name scsa.msg.yahoo.com
server name scsb.msg.yahoo.com
server name scsc.msg.yahoo.com
server name scsd.msg.yahoo.com
server name cs16.msg.dcn.yahoo.com
server name cs19.msg.dcn.yahoo.com
server name cs42.msg.dcn.yahoo.com
server name cs53.msg.dcn.yahoo.com
server name cs54.msg.dcn.yahoo.com
server name ads1.vip.scd.yahoo.com
server name radio1.launch.vip.dal.yahoo.com
server name in1.msg.vip.re2.yahoo.com
server name data1.my.vip.sc5.yahoo.com
server name address1.pim.vip.mud.yahoo.com
server name edit.messenger.yahoo.com
server name messenger.yahoo.com
server name http.pager.yahoo.com
server name privacy.yahoo.com
server name csa.yahoo.com
server name csb.yahoo.com
server name csc.yahoo.com
parameter-map type protocol-info aol-servers
server name login.oscar.aol.com
server name toc.oscar.aol.com
server name oam-d09a.blue.aol.com
parameter-map type protocol-info msn-servers
server name messenger.hotmail.com
server name gateway.messenger.hotmail.com
server name webmessenger.msn.com
password encryption aes
license udi pid CISCO887VA-K9 sn FGL162321CT
object-group service MAIL-PORTS
description QQQ User Mail Restrictions
tcp eq smtp
tcp eq pop3
tcp eq 995
tcp eq 993
udp lt rip
udp lt domain
tcp eq telnet
udp lt ntp
udp lt tftp
tcp eq ftp
tcp eq domain
tcp eq 5900
tcp eq ftp-data
tcp eq 3389
tcp eq 20410
object-group network Network1
description QQQ Management Network
192.168.1.0 255.255.255.0
192.168.4.0 255.255.255.0
192.168.5.0 255.255.255.0
192.168.7.0 255.255.255.0
192.168.8.0 255.255.255.0
range 192.168.0.200 192.168.0.254
range 192.168.0.1 192.168.0.25
object-group network Network2
description QQQ User Network
192.168.2.0 255.255.255.0
192.168.3.0 255.255.255.0
192.168.6.0 255.255.255.0
range 192.168.0.26 192.168.0.199
object-group network QQQ.Local
description QQQ_Domain
192.168.0.0 255.255.255.0
192.168.1.0 255.255.255.0
192.168.2.0 255.255.255.0
192.168.3.0 255.255.255.0
192.168.4.0 255.255.255.0
192.168.5.0 255.255.255.0
192.168.6.0 255.255.255.0
192.168.8.0 255.255.255.0
192.168.7.0 255.255.255.0
192.168.10.0 255.255.255.0
10.1.0.0 255.255.0.0
object-group network QQQ_Management_Group
description QQQ I.T. Devices With UnRestricted Access
range 192.168.0.200 192.168.0.254
range 192.168.0.1 192.168.0.25
192.168.1.0 255.255.255.0
192.168.8.0 255.255.255.0
192.168.7.0 255.255.255.0
192.168.5.0 255.255.255.0
192.168.4.0 255.255.255.0
10.1.0.0 255.255.0.0
192.168.10.0 255.255.255.0
10.8.0.0 255.255.255.0
192.168.9.0 255.255.255.0
192.168.100.0 255.255.255.0
192.168.20.0 255.255.255.0
192.168.21.0 255.255.255.0
192.168.22.0 255.255.255.0
192.168.23.0 255.255.255.0
object-group network QQQ_User_Group
description QQQ I.T. Devices WIth Restricted Access
range 192.168.0.26 192.168.0.199
192.168.2.0 255.255.255.0
192.168.3.0 255.255.255.0
192.168.6.0 255.255.255.0
object-group service WEB
description QQQ User Web Restrictions
tcp eq www
tcp eq 443
tcp eq 8080
tcp eq 1863
tcp eq 5190
username cpadmin privilege 15 password 7 1406031A2C172527
username QQQVPN privilege 15 secret 4 Hk2tP2GgJ1xXtJUqIZr4gmNSgw6q1E.rvzWiYnDAZHU
controller VDSL 0
ip tcp synwait-time 10
no ip ftp passive
class-map type inspect match-all sdm-cls-VPNOutsideToInside-1
match access-group 118
class-map type inspect match-all sdm-cls-VPNOutsideToInside-3
match access-group 121
class-map type inspect match-all sdm-cls-VPNOutsideToInside-2
match access-group 120
class-map type inspect imap match-any ccp-app-imap
match invalid-command
class-map type inspect match-any ccp-cls-protocol-p2p
match protocol edonkey signature
match protocol gnutella signature
match protocol kazaa2 signature
match protocol fasttrack signature
match protocol bittorrent signature
class-map type inspect match-all sdm-cls-VPNOutsideToInside-4
match access-group 122
class-map type inspect match-all SDM_GRE
match access-group name SDM_GRE
class-map type inspect match-any CCP_PPTP
match class-map SDM_GRE
class-map type inspect match-any SDM_AH
match access-group name SDM_AH
class-map type inspect match-any ccp-skinny-inspect
match protocol skinny
class-map type inspect match-any SDM_ESP
match access-group name SDM_ESP
class-map type inspect match-any SDM_VPN_TRAFFIC
match protocol isakmp
match protocol ipsec-msft
match class-map SDM_AH
match class-map SDM_ESP
class-map type inspect match-all SDM_VPN_PT
match access-group 117
match class-map SDM_VPN_TRAFFIC
class-map type inspect match-any ccp-cls-insp-traffic
match protocol pptp
match protocol dns
match protocol ftp
match protocol https
match protocol icmp
match protocol imap
match protocol pop3
match protocol netshow
match protocol shell
match protocol realmedia
match protocol rtsp
match protocol smtp
match protocol sql-net
match protocol streamworks
match protocol tftp
match protocol vdolive
match protocol tcp
match protocol udp
class-map type inspect match-all ccp-insp-traffic
match class-map ccp-cls-insp-traffic
class-map type inspect match-any SDM_IP
match access-group name SDM_IP
class-map type inspect gnutella match-any ccp-app-gnutella
match file-transfer
class-map type inspect match-any SDM_HTTP
match access-group name SDM_HTTP
class-map type inspect match-any SDM_EASY_VPN_SERVER_TRAFFIC
match protocol isakmp
match protocol ipsec-msft
match class-map SDM_AH
match class-map SDM_ESP
class-map type inspect match-all SDM_EASY_VPN_SERVER_PT
match class-map SDM_EASY_VPN_SERVER_TRAFFIC
class-map type inspect match-all sdm-cls-http
match access-group name dmz-traffic
match protocol http
class-map type inspect match-any Telnet
match protocol telnet
class-map type inspect msnmsgr match-any ccp-app-msn-otherservices
match service any
class-map type inspect ymsgr match-any ccp-app-yahoo-otherservices
match service any
class-map type inspect match-any ccp-h323nxg-inspect
match protocol h323-nxg
class-map type inspect match-any ccp-cls-icmp-access
match protocol icmp
match protocol tcp
match protocol udp
class-map type inspect match-any ccp-cls-protocol-im
match protocol ymsgr yahoo-servers
match protocol msnmsgr msn-servers
match protocol aol aol-servers
class-map type inspect aol match-any ccp-app-aol-otherservices
match service any
class-map type inspect match-all ccp-protocol-pop3
match protocol pop3
class-map type inspect match-any ccp-h225ras-inspect
match protocol h225ras
class-map type inspect match-any FIREWALL_EXCEPTIONS_CLASS
match access-group name FIREWALL_EXCEPTIONS_ACL
class-map type inspect match-any ccp-h323annexe-inspect
match protocol h323-annexe
class-map type inspect match-any SDM_EASY_VPN_CTCP_SERVER_PT
match access-group 102
match access-group 103
match access-group 104
match access-group 105
match access-group 106
match access-group 107
match access-group 108
match access-group 109
match access-group 110
match access-group 111
match access-group 112
match access-group 113
match access-group 114
match access-group 115
class-map type inspect match-any SIP
match protocol sip
class-map type inspect pop3 match-any ccp-app-pop3
class-map type inspect match-any SDM_HTTPS
match access-group name SDM_HTTPS
class-map type inspect sip match-any ccp-cls-sip-pv-2
match protocol-violation
class-map type inspect kazaa2 match-any ccp-app-kazaa2
match file-transfer
class-map type inspect match-all ccp-protocol-p2p
match class-map ccp-cls-protocol-p2p
class-map type inspect match-all ccp-cls-ccp-permit-1
match access-group name ETS1
class-map type inspect match-any ccp-h323-inspect
match protocol h323
class-map type inspect msnmsgr match-any ccp-app-msn
match service text-chat
class-map type inspect ymsgr match-any ccp-app-yahoo
match service text-chat
class-map type inspect match-all ccp-cls-ccp-pol-outToIn-1
match access-group name ETS
class-map type inspect match-all ccp-protocol-im
match class-map ccp-cls-protocol-im
class-map type inspect match-all ccp-cls-ccp-pol-outToIn-2
match class-map Telnet
match access-group name Telnet
class-map type inspect match-all ccp-icmp-access
match class-map ccp-cls-icmp-access
class-map type inspect match-all ccp-invalid-src
match access-group 100
class-map type inspect http match-any ccp-app-httpmethods
match request method bcopy
match request method bdelete
match request method bmove
match request method bpropfind
match request method bproppatch
match request method connect
match request method copy
match request method delete
match request method edit
match request method getattribute
match request method getattributenames
match request method getproperties
match request method index
match request method lock
match request method mkcol
match request method mkdir
match request method move
match request method notify
match request method options
match request method poll
match request method propfind
match request method proppatch
match request method put
match request method revadd
match request method revlabel
match request method revlog
match request method revnum
match request method save
match request method search
match request method setattribute
match request method startrev
match request method stoprev
match request method subscribe
match request method trace
match request method unedit
match request method unlock
match request method unsubscribe
class-map type inspect match-any ccp-dmz-protocols
match user-group qqq
match protocol icmp
match protocol http
class-map type inspect edonkey match-any ccp-app-edonkey
match file-transfer
match text-chat
match search-file-name
class-map type inspect match-any ccp-sip-inspect
match protocol sip
class-map type inspect match-all sdm-cls-sip
match access-group name dmz-traffic
match protocol sip
class-map type inspect match-all ccp-dmz-traffic
match access-group name dmz-traffic
match class-map ccp-dmz-protocols
class-map type inspect http match-any ccp-http-blockparam
match request port-misuse im
match request port-misuse p2p
class-map type inspect edonkey match-any ccp-app-edonkeydownload
match file-transfer
class-map type inspect match-all ccp-protocol-imap
match protocol imap
class-map type inspect aol match-any ccp-app-aol
match service text-chat
class-map type inspect edonkey match-any ccp-app-edonkeychat
match search-file-name
match text-chat
class-map type inspect match-all ccp-cls-ccp-permit-dmzservice-1
match class-map SIP
match access-group name SIP
class-map type inspect fasttrack match-any ccp-app-fasttrack
match file-transfer
class-map type inspect http match-any ccp-http-allowparam
match request port-misuse tunneling
class-map type inspect match-all ccp-protocol-http
match protocol http
policy-map type inspect ccp-permit-icmpreply
class type inspect ccp-icmp-access
inspect
class class-default
pass
policy-map type inspect p2p ccp-action-app-p2p
class type inspect edonkey ccp-app-edonkeychat
log
allow
class type inspect edonkey ccp-app-edonkeydownload
log
allow
class type inspect fasttrack ccp-app-fasttrack
log
allow
class type inspect gnutella ccp-app-gnutella
log
allow
class type inspect kazaa2 ccp-app-kazaa2
log
allow
policy-map type inspect PF_OUT_TO_IN
class type inspect FIREWALL_EXCEPTIONS_CLASS
pass
policy-map type inspect PF_IN_TO_OUT
class type inspect FIREWALL_EXCEPTIONS_CLASS
pass
policy-map type inspect im ccp-action-app-im
class type inspect aol ccp-app-aol
log
allow
class type inspect msnmsgr ccp-app-msn
log
allow
class type inspect ymsgr ccp-app-yahoo
log
allow
class type inspect aol ccp-app-aol-otherservices
log
reset
class type inspect msnmsgr ccp-app-msn-otherservices
log
reset
class type inspect ymsgr ccp-app-yahoo-otherservices
log
reset
policy-map type inspect http ccp-action-app-http
class type inspect http ccp-http-blockparam
log
reset
class type inspect http ccp-app-httpmethods
log
reset
class type inspect http ccp-http-allowparam
log
allow
policy-map type inspect imap ccp-action-imap
class type inspect imap ccp-app-imap
log
policy-map type inspect pop3 ccp-action-pop3
class type inspect pop3 ccp-app-pop3
log
policy-map type inspect ccp-inspect
class type inspect ccp-protocol-http
inspect
service-policy http ccp-action-app-http
class type inspect ccp-protocol-imap
inspect
service-policy imap ccp-action-imap
class type inspect ccp-protocol-pop3
inspect
service-policy pop3 ccp-action-pop3
class type inspect ccp-protocol-p2p
inspect
service-policy p2p ccp-action-app-p2p
class type inspect ccp-protocol-im
inspect
service-policy im ccp-action-app-im
class type inspect ccp-insp-traffic
inspect
class type inspect ccp-sip-inspect
inspect
class type inspect ccp-h323-inspect
inspect
class type inspect ccp-h323annexe-inspect
inspect
class type inspect ccp-h225ras-inspect
inspect
class type inspect ccp-h323nxg-inspect
inspect
class type inspect ccp-skinny-inspect
inspect
class type inspect ccp-invalid-src
drop log
class class-default
drop
policy-map type inspect ccp-permit
class type inspect SDM_VPN_PT
pass
class type inspect ccp-cls-ccp-permit-1
pass
class type inspect SDM_EASY_VPN_SERVER_PT
pass
class type inspect SDM_EASY_VPN_CTCP_SERVER_PT
inspect
class class-default
drop
policy-map type inspect sip ccp-app-sip-2
class type inspect sip ccp-cls-sip-pv-2
allow
policy-map type inspect ccp-permit-dmzservice
class type inspect ccp-cls-ccp-permit-dmzservice-1
pass
class type inspect ccp-dmz-traffic
inspect
class type inspect sdm-cls-http
inspect
service-policy http ccp-action-app-http
class type inspect sdm-cls-VPNOutsideToInside-1
inspect
class type inspect sdm-cls-VPNOutsideToInside-2
inspect
class type inspect sdm-cls-VPNOutsideToInside-3
pass
class class-default
pass
policy-map type inspect ccp-pol-outToIn
class type inspect ccp-cls-ccp-pol-outToIn-1
pass
class type inspect ccp-cls-ccp-pol-outToIn-2
pass
class type inspect CCP_PPTP
pass
class type inspect sdm-cls-VPNOutsideToInside-1
inspect
class type inspect sdm-cls-VPNOutsideToInside-2
inspect
class type inspect sdm-cls-VPNOutsideToInside-3
pass
class type inspect sdm-cls-VPNOutsideToInside-4
inspect
class class-default
drop log
policy-map type inspect sdm-permit-ip
class type inspect SDM_IP
pass
class type inspect sdm-cls-VPNOutsideToInside-2
inspect
class type inspect sdm-cls-VPNOutsideToInside-3
pass
class type inspect sdm-cls-VPNOutsideToInside-4
inspect
class class-default
drop log
zone security dmz-zone
zone security in-zone
zone security out-zone
zone security ezvpn-zone
zone-pair security ccp-zp-out-dmz source out-zone destination dmz-zone
service-policy type inspect ccp-permit-dmzservice
zone-pair security ccp-zp-out-self source out-zone destination self
service-policy type inspect ccp-permit
zone-pair security ccp-zp-in-out source in-zone destination out-zone
service-policy type inspect ccp-inspect
zone-pair security ccp-zp-out-zone-To-in-zone source out-zone destination in-zone
service-policy type inspect ccp-pol-outToIn
zone-pair security ccp-zp-in-dmz source in-zone destination dmz-zone
service-policy type inspect ccp-permit-dmzservice
zone-pair security ccp-zp-self-out source self destination out-zone
service-policy type inspect ccp-permit-icmpreply
zone-pair security dmz-to-in source dmz-zone destination in-zone
service-policy type inspect ccp-permit-icmpreply
zone-pair security sdm-zp-ezvpn-out1 source ezvpn-zone destination out-zone
service-policy type inspect sdm-permit-ip
zone-pair security sdm-zp-in-ezvpn2 source in-zone destination ezvpn-zone
service-policy type inspect sdm-permit-ip
zone-pair security sdm-zp-in-ezvpn1 source dmz-zone destination ezvpn-zone
service-policy type inspect sdm-permit-ip
zone-pair security sdm-zp-ezvpn-in2 source ezvpn-zone destination in-zone
service-policy type inspect sdm-permit-ip
zone-pair security sdm-zp-ezvpn-in1 source ezvpn-zone destination dmz-zone
service-policy type inspect sdm-permit-ip
zone-pair security sdm-zp-out-ezpn1 source out-zone destination ezvpn-zone
service-policy type inspect sdm-permit-ip
zone-pair security sdm-zp-ezvpn-in3 source ezvpn-zone destination ezvpn-zone
service-policy type inspect sdm-permit-ip
crypto ctcp port 10000 1723 6299
crypto isakmp policy 1
encr 3des
authentication pre-share
group 2
crypto isakmp policy 2
encr aes 256
authentication pre-share
group 2
crypto isakmp key 6 PbKM_WfaCM[hYNXAFOUgCNgCB_ZdJEAAB address 220.245.109.219
crypto isakmp key 6 NddQRR[O^KY`GRDC[VZUEPE`CSJ^CDAAB address 0.0.0.0 0.0.0.0
crypto isakmp client configuration group QQQ
key 6 UWVBhb`Lgc_AZbDYWDFZiGZTTadNYTAAB
dns 192.168.0.6 202.1.161.36
wins 192.168.0.6
domain QQQ.Local
pool SDM_POOL_1
include-local-lan
max-users 20
max-logins 1
netmask 255.255.255.0
banner ^CCWelcome to QQQ VPN!!!!1                 ^C
crypto isakmp profile ciscocp-ike-profile-1
   match identity group QQQ
   client authentication list ciscocp_vpn_xauth_ml_1
   isakmp authorization list ciscocp_vpn_group_ml_1
   client configuration address initiate
   client configuration address respond
   keepalive 10 retry 2
   virtual-template 1
crypto ipsec transform-set ESP_AES_SHA esp-aes 256 esp-sha-hmac
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec profile CiscoCP_Profile1
set security-association idle-time 43200
set transform-set ESP_AES_SHA
set isakmp-profile ciscocp-ike-profile-1
crypto map SDM_CMAP_1 1 ipsec-isakmp
description Tunnel to220.245.109.219
set peer 220.245.109.219
set transform-set ESP-3DES-SHA
match address 119
interface Loopback0
description QQQ_VPN
ip address 192.168.9.254 255.255.255.0
interface Null0
no ip unreachables
interface Ethernet0
no ip address
no ip redirects
no ip unreachables
no ip proxy-arp
ip flow ingress
shutdown
no fair-queue
interface ATM0
no ip address
no ip redirects
no ip unreachables
no ip proxy-arp
ip flow ingress
no atm ilmi-keepalive
interface ATM0.1 point-to-point
description Telekom_ADSL
no ip redirects
no ip unreachables
no ip proxy-arp
ip flow ingress
zone-member security out-zone
pvc 8/35
pppoe-client dial-pool-number 1
interface FastEthernet0
description QQQ_LAN-VLAN_1
switchport access vlan 1
no ip address
interface FastEthernet1
description QQQ_LAN-VLAN_1
no ip address
interface FastEthernet2
description QQQ_WAN-VLAN_2
switchport access vlan 2
no ip address
interface FastEthernet3
description QQQ_DMZ-IP_PBX-VLAN_3
switchport access vlan 3
no ip address
interface Virtual-Template1 type tunnel
description QQQ_Easy_VPN
ip unnumbered Loopback0
ip nat inside
ip virtual-reassembly in
zone-member security ezvpn-zone
tunnel mode ipsec ipv4
tunnel protection ipsec profile CiscoCP_Profile1
interface Vlan1
description QQQ_LAN-VLAN1$FW_INSIDE$
ip address 192.168.0.254 255.255.255.0
ip access-group QQQ_ACL in
ip mask-reply
ip nat inside
ip virtual-reassembly in
zone-member security in-zone
ip tcp adjust-mss 1412
interface Vlan2
description QQQ_WAN-VLAN2$FW_INSIDE$
ip address 192.168.5.254 255.255.255.0
ip access-group QQQ_ACL in
ip mask-reply
ip nat inside
ip virtual-reassembly in
zone-member security in-zone
ip tcp adjust-mss 1412
interface Vlan3
description QQQ_IP-PBX_WAN-VLAN3
ip address 192.168.4.254 255.255.255.0
ip mask-reply
ip nat inside
ip virtual-reassembly in
zone-member security dmz-zone
interface Vlan4
description VLAN4 - 192.168.20.xxx (Spare)
ip address 192.168.20.253 255.255.255.0
ip nat inside
ip virtual-reassembly in
zone-member security in-zone
interface Dialer0
description ATM Dialer
no ip address
no ip redirects
no ip unreachables
no ip proxy-arp
ip flow ingress
ip nat outside
ip virtual-reassembly in
zone-member security out-zone
no cdp enable
interface Dialer2
description $FW_OUTSIDE$
ip address negotiated
no ip redirects
no ip unreachables
no ip proxy-arp
ip mtu 1452
ip nbar protocol-discovery
ip flow ingress
ip flow egress
ip nat outside
ip virtual-reassembly in
zone-member security out-zone
encapsulation ppp
dialer pool 1
dialer-group 1
ppp authentication chap pap callin
ppp chap hostname xxxxxxxxxxxxxxxxxxx
ppp chap password 7 xxxxxxxxxxxxxxxxxxxxxxxxx
ppp pap sent-username xxxxxxxxxx0 password 7 xxxxxxxxxxxxxxxxxxxxx
no cdp enable
crypto map SDM_CMAP_1
router rip
version 2
redistribute static
passive-interface ATM0
passive-interface ATM0.1
passive-interface Dialer0
passive-interface Dialer2
passive-interface Ethernet0
passive-interface Loopback0
network 10.0.0.0
network 192.168.0.0
network 192.168.1.0
network 192.168.2.0
network 192.168.3.0
network 192.168.4.0
network 192.168.5.0
network 192.168.6.0
network 192.168.7.0
network 192.168.8.0
network 192.168.10.0
network 192.168.100.0
ip local pool SDM_POOL_1 192.168.5.100 192.168.5.200
ip forward-protocol nd
ip http server
ip http access-class 5
ip http authentication local
ip http secure-server
ip nat pool NAT_IP 192.168.0.210 192.168.0.235 netmask 255.255.255.0
ip nat inside source static tcp 192.168.4.253 5060 interface Dialer2 5060
ip nat inside source static tcp 192.168.0.240 20408 interface Dialer2 6208
ip nat inside source static tcp 192.168.0.240 20409 interface Dialer2 6209
ip nat inside source static tcp 192.168.0.240 20410 interface Dialer2 6200
ip nat inside source static tcp 192.168.1.240 20408 interface Dialer2 6218
ip nat inside source static tcp 192.168.1.240 20409 interface Dialer2 6219
ip nat inside source static tcp 192.168.1.240 20410 interface Dialer2 6210
ip nat inside source static tcp 192.168.7.240 20408 interface Dialer2 6278
ip nat inside source static tcp 192.168.7.240 20409 interface Dialer2 6279
ip nat inside source static tcp 192.168.7.240 20410 interface Dialer2 6270
ip nat inside source static tcp 192.168.8.240 20408 interface Dialer2 6288
ip nat inside source static tcp 192.168.8.240 20409 interface Dialer2 6289
ip nat inside source static tcp 192.168.8.240 20410 interface Dialer2 6280
ip nat inside source static tcp 192.168.0.6 1723 interface Dialer2 1723
ip nat inside source static tcp 192.168.0.6 3389 interface Dialer2 6389
ip nat inside source static tcp 192.168.0.24 3389 interface Dialer2 6390
ip nat inside source static tcp 192.168.4.253 8022 interface Dialer2 8022
ip nat inside source static tcp 192.168.4.253 80 interface Dialer2 8021
ip nat inside source static tcp 192.168.0.254 23 interface Dialer2 8023
ip nat inside source static tcp 192.168.0.6 443 interface Dialer2 443
ip nat inside source route-map SDM_RMAP_1 interface Dialer2 overload
ip default-network 192.168.0.0
ip default-network 192.168.4.0
ip route 0.0.0.0 0.0.0.0 Dialer2 permanent
ip route 10.1.0.0 255.255.0.0 Vlan2 permanent
ip route 10.8.0.0 255.255.255.0 Vlan2 permanent
ip route 192.168.0.0 255.255.255.0 Vlan1 permanent
ip route 192.168.4.0 255.255.255.0 Vlan3 permanent
ip route 192.168.5.0 255.255.255.0 Vlan2 permanent
ip route 192.168.100.0 255.255.255.0 Dialer2 permanent
ip access-list extended ACCESS_FROM_INSIDE
permit ip object-group QQQ_Management_Group any
permit tcp object-group QQQ_User_Group any eq smtp pop3
permit tcp object-group QQQ_User_Group any eq 993 995
permit tcp 192.168.0.0 0.0.0.255 any eq smtp pop3
permit tcp 192.168.0.0 0.0.0.255 any eq 993 995
permit ip 192.168.1.0 0.0.0.255 any
permit ip 192.168.4.0 0.0.0.255 any
permit ip 192.168.5.0 0.0.0.255 any
permit ip 192.168.7.0 0.0.0.255 any
permit ip 192.168.8.0 0.0.0.255 any
permit tcp 192.168.2.0 0.0.0.255 any eq www 443 8080 domain
permit tcp 192.168.2.0 0.0.0.255 any eq www 443 8080 domain time-range QQQ_Control
permit tcp 192.168.3.0 0.0.0.255 any eq www 443 8080 domain time-range QQQ_Control
permit tcp 192.168.4.0 0.0.0.255 any eq www 443 8080 domain time-range QQQ_Control
permit udp 192.168.2.0 0.0.0.255 any eq domain time-range QQQ_Control
permit udp 192.168.3.0 0.0.0.255 any eq domain time-range QQQ_Control
permit udp 192.168.4.0 0.0.0.255 any eq domain time-range QQQ_Control
ip access-list extended ETS
remark CCP_ACL Category=128
permit ip host 203.219.237.252 any
ip access-list extended ETS1
remark CCP_ACL Category=128
permit ip host 203.219.237.252 any
ip access-list extended FIREWALL_EXCEPTIONS_ACL
permit tcp any host 192.168.0.100 eq 25565
permit tcp any eq 25565 host 192.168.0.100
ip access-list extended QQQ_ACL
permit ip any host 192.168.4.253
permit udp any any eq bootps bootpc
permit ip any 192.168.4.0 0.0.0.255
permit ip host 203.219.237.252 any
remark QQQ Internet Control List
remark CCP_ACL Category=17
remark Auto generated by CCP for NTP (123) 203.12.160.2
permit udp host 203.12.160.2 eq ntp any eq ntp
remark AD Services
permit udp host 192.168.0.6 eq domain any
remark Unrestricted Access
permit ip object-group QQQ_Management_Group any
remark Restricted Users
permit object-group MAIL-PORTS object-group QQQ_User_Group any
permit ip 192.168.0.0 0.0.0.255 any time-range QQQ_Control
permit ip 192.168.2.0 0.0.0.255 any time-range QQQ_Control
permit ip 192.168.3.0 0.0.0.255 any time-range QQQ_Control
permit ip 192.168.6.0 0.0.0.255 any time-range QQQ_Control
remark ICMP Full Access
permit icmp object-group QQQ_User_Group any
permit tcp 192.168.2.0 0.0.0.255 eq www 443 8080 5190 1863 any time-range QQQ_Control
permit tcp 192.168.3.0 0.0.0.255 eq www 443 8080 5190 1863 any time-range QQQ_Control
permit tcp 192.168.6.0 0.0.0.255 eq www 443 8080 5190 1863 any time-range QQQ_Control
permit udp 192.168.6.0 0.0.0.255 eq 80 443 8080 5190 1863 any time-range QQQ_Control
permit tcp 192.168.0.0 0.0.0.255 eq www 443 8080 5190 1863 any time-range QQQ_Control
permit udp 192.168.0.0 0.0.0.255 eq 80 443 8080 5190 1863 any time-range QQQ_Control
permit udp 192.168.2.0 0.0.0.255 eq 80 443 8080 5190 1863 any time-range QQQ_Control
permit udp 192.168.3.0 0.0.0.255 eq 80 443 8080 5190 1863 any time-range QQQ_Control
ip access-list extended QQQ_NAT
remark CCP_ACL Category=18
remark IPSec Rule
deny   ip 192.168.0.0 0.0.255.255 192.168.100.0 0.0.0.255
permit ip any any
ip access-list extended SDM_AH
remark CCP_ACL Category=1
permit ahp any any
ip access-list extended SDM_ESP
remark CCP_ACL Category=1
permit esp any any
ip access-list extended SDM_GRE
remark CCP_ACL Category=1
permit gre any any
ip access-list extended SDM_HTTP
remark CCP_ACL Category=0
permit tcp any any eq telnet
ip access-list extended SDM_HTTPS
remark CCP_ACL Category=0
permit tcp any any eq 443
ip access-list extended SDM_IP
remark CCP_ACL Category=1
permit ip any any
ip access-list extended SIP
remark CCP_ACL Category=128
permit ip any 192.168.4.0 0.0.0.255
ip access-list extended Telnet
remark CCP_ACL Category=128
permit ip any any
ip access-list extended dmz-traffic
remark CCP_ACL Category=1
permit ip any 192.168.4.0 0.0.0.255
access-list 1 remark CCP_ACL Category=2
access-list 1 remark QQQ_DMZ
access-list 1 permit 192.168.4.0 0.0.0.255
access-list 2 remark CCP_ACL Category=2
access-list 2 remark QQQ_LAN
access-list 2 permit 192.168.0.0 0.0.0.255
access-list 3 remark QQQ Insid NAT
access-list 3 remark CCP_ACL Category=2
access-list 3 permit 192.168.0.0 0.0.0.255
access-list 3 permit 192.168.1.0 0.0.0.255
access-list 3 permit 192.168.2.0 0.0.0.255
access-list 3 permit 192.168.3.0 0.0.0.255
access-list 3 permit 192.168.4.0 0.0.0.255
access-list 3 permit 192.168.5.0 0.0.0.255
access-list 3 permit 192.168.6.0 0.0.0.255
access-list 3 permit 192.168.7.0 0.0.0.255
access-list 3 permit 192.168.8.0 0.0.0.255
access-list 3 permit 192.168.9.0 0.0.0.255
access-list 3 permit 192.168.10.0 0.0.0.255
access-list 4 remark QQQ_NAT
access-list 4 remark CCP_ACL Category=2
access-list 4 permit 10.1.0.0 0.0.255.255
access-list 4 permit 10.8.0.0 0.0.0.255
access-list 4 permit 192.168.0.0 0.0.0.255
access-list 4 permit 192.168.1.0 0.0.0.255
access-list 4 permit 192.168.2.0 0.0.0.255
access-list 4 permit 192.168.3.0 0.0.0.255
access-list 4 permit 192.168.4.0 0.0.0.255
access-list 4 permit 192.168.5.0 0.0.0.255
access-list 4 permit 192.168.6.0 0.0.0.255
access-list 4 permit 192.168.7.0 0.0.0.255
access-list 4 permit 192.168.8.0 0.0.0.255
access-list 4 permit 192.168.9.0 0.0.0.255
access-list 4 permit 192.168.10.0 0.0.0.255
access-list 5 remark HTTP Access-class list
access-list 5 remark CCP_ACL Category=1
access-list 5 permit 192.168.4.0 0.0.0.255
access-list 5 permit 192.168.0.0 0.0.0.255
access-list 5 deny   any
access-list 100 remark CCP_ACL Category=128
access-list 100 permit ip 192.168.4.0 0.0.0.255 any
access-list 100 permit ip 127.0.0.0 0.255.255.255 any
access-list 100 permit ip host 255.255.255.255 any
access-list 101 remark QQQ_Extended_ACL
access-list 101 remark CCP_ACL Category=1
access-list 101 permit tcp any host 192.168.0.254 eq 10000
access-list 101 permit udp any host 192.168.0.254 eq non500-isakmp
access-list 101 permit udp any host 192.168.0.254 eq isakmp
access-list 101 permit esp any host 192.168.0.254
access-list 101 permit ahp any host 192.168.0.254
access-list 101 remark Auto generated by CCP for NTP (123) 203.12.160.2
access-list 101 permit udp host 203.12.160.2 eq ntp host 192.168.4.254 eq ntp
access-list 101 permit udp host 192.168.0.6 eq domain any
access-list 101 remark NTP (123) 203.12.160.2
access-list 101 permit udp host 203.12.160.2 eq ntp any eq ntp
access-list 101 remark QQQ_ANY_Any
access-list 101 permit ip object-group QQQ.Local any
access-list 101 remark QQQ_DMZ
access-list 101 permit ip any 192.168.4.0 0.0.0.255
access-list 101 remark QQQ_GRE
access-list 101 permit gre any any
access-list 101 remark QQQ_Ping
access-list 101 permit icmp any any
access-list 102 remark CCP_ACL Category=1
access-list 102 permit tcp any any eq 10000
access-list 103 permit tcp any 192.168.0.0 0.0.0.255 eq 443
access-list 103 remark CCP_ACL Category=1
access-list 103 permit tcp any any eq 10000
access-list 103 permit tcp any 192.168.4.0 0.0.0.255 eq 8022
access-list 103 permit tcp any 192.168.4.0 0.0.0.255 eq telnet
access-list 103 permit tcp any 192.168.4.0 0.0.0.255 eq www
access-list 103 permit tcp any 192.168.4.0 0.0.0.255 eq 5060
access-list 103 permit tcp any eq telnet host 192.168.0.254
access-list 103 permit tcp any 192.168.0.0 0.0.0.255 eq telnet
access-list 103 permit udp any 192.168.4.0 0.0.0.255 eq 5060
access-list 103 permit udp any 192.168.4.0 0.0.0.255 range 10001 12000
access-list 104 remark CCP_ACL Category=1
access-list 104 permit tcp any any eq 10000
access-list 105 remark CCP_ACL Category=1
access-list 105 permit tcp any any eq 10000
access-list 106 remark CCP_ACL Category=1
access-list 106 permit tcp any any eq 10000
access-list 107 remark CCP_ACL Category=1
access-list 107 permit tcp any any eq 10000
access-list 108 remark CCP_ACL Category=1
access-list 108 permit tcp any any eq 10000
access-list 109 remark CCP_ACL Category=1
access-list 109 permit tcp any any eq 10000
access-list 110 remark CCP_ACL Category=1
access-list 110 permit tcp any any eq 10000
access-list 111 remark CCP_ACL Category=1
access-list 111 permit tcp any any eq 10000
access-list 112 remark CCP_ACL Category=1
access-list 112 permit tcp any any eq 10000
access-list 113 remark CCP_ACL Category=1
access-list 113 permit tcp any any eq 10000
access-list 114 remark CCP_ACL Category=1
access-list 114 permit tcp any any eq 10000
access-list 115 remark CCP_ACL Category=1
access-list 115 permit tcp any any eq 10000
access-list 116 remark CCP_ACL Category=4
access-list 116 remark IPSec Rule
access-list 116 permit ip 192.168.0.0 0.0.255.255 192.168.100.0 0.0.0.255
access-list 117 remark CCP_ACL Category=128
access-list 117 permit ip any any
access-list 117 permit ip host 220.245.109.219 any
access-list 118 remark CCP_ACL Category=0
access-list 118 permit ip 192.168.100.0 0.0.0.255 192.168.0.0 0.0.0.255
access-list 119 remark CCP_ACL Category=4
access-list 119 remark IPSec Rule
access-list 119 permit ip 192.168.0.0 0.0.255.255 192.168.100.0 0.0.0.255
access-list 120 remark CCP_ACL Category=0
access-list 120 permit ip 192.168.100.0 0.0.0.255 192.168.0.0 0.0.0.255
access-list 121 remark CCP_ACL Category=0
access-list 121 permit ip 192.168.100.0 0.0.0.255 192.168.0.0 0.0.255.255
access-list 122 remark CCP_ACL Category=0
access-list 122 permit ip 192.168.100.0 0.0.0.255 192.168.0.0 0.0.255.255
dialer-list 1 protocol ip permit
route-map SDM_RMAP_1 permit 1
match ip address QQQ_NAT
banner login ^CCWelcome to QQQ ADSL Gateway

It turns out the problem had nothing to do with wires or splitters. The Verizon tech was at my house yesterday and the ONT was failing. He replaced part of the ONT and it fixed the problem (finally!). At least I was able to watch the Celtics game last night.
I have a Tellabs ONT. Not sure the model but it's older like the ones in this thread.
http://www.dslreports.com/forum/r19982000-Mounting-board-for-612-ONT

Help setting up port forwarding for Ekiga

Hi
I am trying to set up Ekiga on my Arch X86_64 box but I can't get port forwarding to work on the Thomson TG585v7 wireless router, which I am sharing with a neighbor. I have tried some how-to's I found via Google and set up Application/Game Sharing for the ports Ekiga uses. I also set up static IP connection as it seems to be needed by the router for port forwarding to work but Ekiga still reports that it cannot set up my network connection and asks me to set up port forwading manually, which I have already done.
I would very much appreciate any help to get Ekiga going for me.
My thanks in advance.

graysky wrote:No idea for you specific hardware but should be pretty trivial. http://wiki.ekiga.org/index.php/Enable_ … g_manually
Thanks, but the problem is that setting up the router doesn't seem to work. I checked and repeated the set up a few times but no result. I feel I am missing a little detail somewhere but can't put my finger on it :-(

RV016 Wired 16 Port Cisco Router Port Forwarding Functions

Thank you for your time. I have created and attached a Word Document discussing the Cisco Model RV016 16 port wired Router port forwarding functions for your review. I would appreciate your time in reviewing it with your comments and suggestions.
Thank you very much,
Eddie LeFiles
850-471-1271

Thank you for your time. I have created and attached a Word Document discussing the Cisco Model RV016 16 port wired Router port forwarding functions for your review. I would appreciate your time in reviewing it with your comments and suggestions.
Thank you very much,
Eddie LeFiles
850-471-1271

Help please, with port forwarding settings

I have an MSI RG60 wireless router (Ethernet hard wired to my XP Home PC) and don't know what settings to use for port forwarding, to enable my WinMX and BitTorrent clients to work successfully.
I have the port numbers, and assume that this information goes in the Service Port box, i.e. 6699, or 6881-6889.
I know which ports are TCP and which are UDP, but I don't know what IP address to enter or which Common Service Port type to choose. Can anyone help please?
I'm pretty sure that other settings in my PC are OK as I have successfully been running a Belkin router for a couple of years, and have only replaced it with the new MSI unit due to reliability problems.

It does indeed have port triggering, but it wants incoming and trigger port protocol info, along with trigger and incoming port numbers.
How can I type ipconfig into either of teh clients...WinMx or Bit Torrent?

Help needed please (Port forwarding/Firewall Question)

So im hooked up thru my router so if I want to play a game I have to port forward so im told.
Ok, I im at my port forwarding menu and its asking for the following info...some of this info I know and some I have no idea what it means or where I can get it from. Heres the parts im asked to enter that I have no idea what to enter......
Source IP Address:
Destination IP Address
Source Netmask:
Destination Port Map
Where do I find out these things!?...Im a COMPLETE novice when it comes to routers and im so confused.

Hello,
Unfortunately, that information is going to have to come from the people who are providing you the online game.
The settings you need are going to depend on what their program requires, and how they communicate with your computer.
All of this is different for each service you are trying to use.
Here are some articles to get you familiarized with the concept though:
http://en.wikipedia.org/wiki/Port_forwarding
http://forums.furthurnet.org/viewtopic.php?p=3821
http://www.boutell.com/newfaq/creating/forwardports.html
http://panasonic.co.jp/pcc/products/en/netwkcam/technic/port_fwrd.html
http://p2p.weblogsinc.com/2005/04/24/how-to-configure-your-router-to-allow-fast- bittorrent-downloads/
While they all discuss doing it with different routers, the principals and ideas are the same.
But, the actual configuration is going to depend on the specific needs of the service you are trying to use (the particular online game).
I hope this helps.

I need Help setting up port forwarding for my foscam FI8910W.

I am currently on Mac OS X 10.7.5. My ISP is verizon FIOS and I have an Actiontec MI424WR router with the wireless turned off. I have an AirPort Extreme running from the actiontec router for my wireless network. First of all I need to know if I should plug the Foscam into the actiontec router or the Airport Extreme? Then I need to know if I should set up the port forwarding on the Actiontec or the Airport Extreme. Lastly I need detailed instructions on how to set up the port forwarding. Hopefully someone has a solution. Thanks

OK, and what sort of help do you need?

PLEASE HELP!! port forwarding issues!

hello guys,
this is driving me absolutely crazy, i have read every forum out there and possibly watched every video and simply cant see what i'm doing wrong!
i want to open the following ports to allow my DVR system for cameras to work:
9000
80
60000
37777
i have followed all of the steps necessary but when i checked using a port checker tool, it said the ports are still closed?!?!?!?!?
i read on a youtube video that the ports stay closed due to some sort of a security measure?
speaking to customer services was no help either, the guy had no idea about what port forwarding is!

this link may be of some help http://forumhelp.dyndns.info/networking/portforward.html
If you want to say thanks for a helpful answer,please click on the Ratings star on the left-hand side If the reply answers your question then please mark as ’Mark as Accepted Solution’

I need help changing settings (port forward?) after a physical server move

Hi! I have a 10.6 server that I use at home. All is well and good there. The Airport Extreme assigns IP addresses for the network. I have www.mydomain.com that runs on the server -- I use it for testing web apps, etc. I use DynDNS with their client app that send the Comcast dynamic IP address back to DynDNS to keep the server on the grid.
My friend has a 10.6 server. He has www.hisdomain.com as a home business. He also uses DynDNS in a similar way. His landlord just informed him that his apartment is going to be sold from underneath him and he has to move ASAP. It looks like he won't have a permanent place for a month or two, so I offered to let him keep his server at my place.
We both run websites on port 443 and port 80.
After attaching his server to my network, his domain name updates, but typing www.hisdomain.com into a browser lands me on www.mydomain.com. I guess that the problem is port forwarding... the router sends all 443 and 80 requests to my server.
How do I configure this so that services for hisdomain.com are forwarded to his server while services for mydomain.com are forwarded to my server?

Short answer: you can't, although there are a couple of ways to sort-of kluge it.
Long answer: When your router gets an incoming connection, the only thing it has to go on is the IP address and port number (the domain name is sent much later, after TCP session with the server is established). So unless you have multiple public IP addresses (and a router that can handle them), or want to put the sites on different ports...
Speaking of which, here's kluge #1: run his server on different ports (e.g. 81 and 444, or maybe 8080 and 8043) and set the router to forward them to his server. Problem: the user has to include the port number in the URL when they connect, or they'll get your server.
Partial solution (and kluge #2): add a virtual site on your server, with the hostname www.hisdomain.com, go to its Aliases section, and add a rule in the URL Aliases & Redirects section, with these settings:
Type: RedirectMatch
Pattern: (.*)$
Path: http://www.hisdomain.com:81$1
Then build an SSL version that redirects to https://www.hisdomain.com:444$1. Problem: when the client connects, they'll get your SSL certificate instead of his (again, it happens before the client sends the domain name it's trying to reach), and get a cert error. No fix for this.
Kluge #3: instead of making the virtual site redirect clients to his server, add a reverse proxy so your server'll transparently forward requests to his server, and proxy the replies. I haven't done this, but I think what you need to do is make a virtual site (as above), and under its Proxy tab (the one under the virtual site, not the one under the Settings section), check the Enable Reverse Proxy box, leave the Proxy Path as "/" and the Sticky Session Identifier field blank, and add a Balancer member with the Server URL "http://hisinternalipaddress" and a blank Route. Or something like that. Again, you could do the same for https as well, but you'll have the same certificate problem.

Help me with port forwarding please?

Hello all.
I have a Cisco 1605r connected to a cable modem to share my internet connection. I am trying to play a flight sim that requires me to forward 2 udp ports (2934 and 2935) to the PC that I am playing the game on. I tried to add what I thought was the right configuration change but, its still not working. If any of you could review my config and the output from "sh ip nat translations" to help me fix this, I would really appreciate it.
Thank You, Chris
Here we go...
1605r#sh run
Building configuration...
Current configuration : 1804 bytes
version 12.2
no service pad
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
hostname 1605r
enable secret 5
ip subnet-zero
no ip source-route
ip name-server
ip name-server
ip name-server
no ip bootp server
interface Ethernet0
ip address dhcp
no ip proxy-arp
ip nat outside
no cdp enable
interface Ethernet1
ip address 192.168.1.1 255.255.255.0
no ip proxy-arp
ip nat inside
no cdp enable
ip nat inside source list 1 interface Ethernet0 overload
ip nat inside source static udp 192.168.1.101 2935 interface Ethernet0 2935
ip nat inside source static udp 192.168.1.101 2934 interface Ethernet0 2934
ip nat inside source static tcp 192.168.1.101 3724 interface Ethernet0 3724
ip nat inside source static tcp 192.168.1.101 6112 interface Ethernet0 6112
ip nat inside source static tcp 192.168.1.101 6881 interface Ethernet0 6881
ip classless
ip route 0.0.0.0 0.0.0.0 216.254.117.1
no ip http server
access-list 1 permit 192.168.1.0 0.0.0.255
no cdp run
banner login ^CC
^C
line con 0
password
login
line vty 0 4
exec-timeout 0 1
no login
no exec
transport input none
end
And here is the output from
sh ip nat translations | inc 2935
and
sh ip nat translations | inc 2934
x.x.x.x is my dhcp assigned address from my isp:
udp x.x.x.x:2935 192.168.1.101:2935 --- ---
udp x.x.x.x:2934 192.168.1.101:2934 65.49.176.170:1157 65.49.176.170:1157
udp x.x.x.x:2934 192.168.1.101:2934 --- ---
Does everything look ok on my end?
Thanks for any help in advance! :)

I think you are missing extendable keyword after ip nat inside source static command.Please try it.
ip nat inside source static udp 192.168.1.101 2935 interface Ethernet0 2935 extendable
ip nat inside source static udp 192.168.1.101 2934 interface Ethernet0 2934 extendable
ip nat inside source static tcp 192.168.1.101 3724 interface Ethernet0 3724 extendable
ip nat inside source static tcp 192.168.1.101 6112 interface Ethernet0 6112 extendable
ip nat inside source static tcp 192.168.1.101 6881 interface Ethernet0 6881 extendable
Bcos you are mapping different port to same inside ip addresses.
If it works let me know
Thanks & Regards

Cisco 878 port forwarding not working

I've configged ports to map for smtp, http, ftp, pop3 and https.
When telnetting to the router and checking on the router with show ip nat translation, the correct mappings are made.
The telnet session with the machine behind the router is not established however.
Telnetting from the router to the same machine on the correct ports does work.
At first I thought it was a config error, but the ip nat config is working fine on other routers.
I then put the config on a new 878, thinking some hardware problem. That didn't help, so I'm back at thinking it's a config error.
See attached file for logging and ip nat output as well as config.
Many thanks in advance.
Wouter

No, the ranges are not the same. That is, they share the same B-class stats, but no C-class.
Incidentally, the extendable parameter is present in this ios version. When I change the parameter interface dialer0 to the ip address associated with the interface, extendable is addedd automatically. No joy however.
Today I'm going to try and downgrade the ios, another router with 12.4(4)T1 does have functional port mappings....

Need help setting up port forwarding

Dear Friends
I have just purchased a wireless linksystem 2.4 -g broadband router and my internet connection is running really well except my web server
I want to redirect people to my web site online game but my Isprovider has blocked access to port 80
How can I program my router to bypass this limitation from my ISprovider ?
I have registered my domain name with dns exit.com and also have a permanent software installed for any ip changes .
Any advice will be appreciated and helpful
Emmerson

Dear Friends
I have managed to come back to my original set up and I can reach my web server and others also but only as long as we are connected to the same isp provider
As soon as they come from another source the provider blocks the entry
My web server is using port 80
How can iIdirect people to my web server and bypass port 80 and this restriction from my isp provider
Emmerson

Help with port forwarding to application

Help needed to Port Forward on to my PS3.
I need to forward the following ports:
UDP: 3074; 3659; 6000
TCP: 80; 443; 3659; 10000 - 10099; 42127
Have previously given the PS3 a static IP, set the port forwarding rules and then forwarded to the IP address, but it appears the ports have not opened as expected.
Help Keith

I can only see one image which just shows the application mapping, but no indication as to whether you had clicked the "apply" button.
Why are you forwarding ports 80 and 443, are you running a webserver on the PS3, as those ports are used for web serving.
As a matter of interest, your port 80 is showing as open at the moment, so is the PS3 turned on, or is port 80 mapped to something else instead?
What I would like you to do is to start from the beginning, with just the single TCP port number 3659 assigned to the PS3.
It will mean removing the other assignments, but it will make things a bit easier.
If you could do that please, and then we can do some tests.
There are some useful help pages here, for BT Broadband customers only, on my personal website.
BT Broadband customers - help with broadband, WiFi, networking, e-mail and phones.

Urgent help with Port Forwarding?

Hi all!
I hope my posting in the right section.
Basically I have a DVR in my home. I want to be able to view the 1 camera that I have externally (from a different home)
I have managed to be able to view the camera internally on my network (the dvr is plugged into the BT HUB 3)
I did this by Advanced Settings>Port Forwarding>Supported Apps>
I was told by the Manifacturer of the DVR that the ports i needed to forward are 8234 to 8239
Does this look correct to you guys?
The DVR i have a is a Digital Sprite 2 PLUS. Ive turned the firewall off on the router settings as I thought that could be the problem. I can view the dvr internally as I said above using the DVR i.p 192.168.1.69 perfectly, but when I type in my external i.p via my other home it wont connect at all.
Could anybody help me as to what im doing wrong?
Thanks for any replys !
James.

You are replying to an old posting.
The information on this link may help you.
Port forwarding problems
There are some useful help pages here, for BT Broadband customers only, on my personal website.
BT Broadband customers - help with broadband, WiFi, networking, e-mail and phones.

HELP!! Cisco RV180 Port Forwarding

Similar Messages

Maybe you are looking for