Help connecting printer and tvs on WRT54g v8

I recently reset my router and settings. My laptop is connected to the internet via wireless, with no problems. However, I am trying to reconnect my wifi printer and tv's, and they will not connect. They pick-up the network, but they say they cannot connect to the access point, or the passphrase is incorrect.
I have tried to look at the network settings on my linksys easyadvisor, but it is mostly blank or n/a, which it never was before. When I go to 192.168.1.1 it shows the correct passphrase. I have no idea what went wrong here! If someone could please help!

Connect the computer to the router with the Ethernet cable. Open the Linksys router setup page.
Go to Wireless tab and click on Wireless security sub tab. Make sure that you have the correct network key/passphrase.
Go to Wireless MAC filter sub tab and make sure that it is disabled.
Try to connect to the wireless network and see if that works.
Make sure that firmware on your router is upgraded to the latest.

Similar Messages

  • HP Web Jetadmin, PC-CONNECTED printer and Toner level problem

    HP Web Jetadmin 10.3.93994 (10.3 SR7) running on Windows Server 2012 (Microsoft Windows NT 6.2.9200.0),
    HP LaserJet M1536dnf MFP is connected via USB to the computer with Windows 7 SR1 64.
    The latest drivers installed, SNMP, HP SNMP Proxy_64_10_3_0010 and HPWSProxyService_10_3_1 installed.
    HP ToolboxFX shows the toner level, the approximate number of pages remaining, cartridge serial number, etc.
    HP SNMP Proxy is not working.
    HP WS Proxy runs, HP Web Jetadmin displays all but the state of supplies - writes "not available".
    File HPWSProxyServiceLog.log errors and warnings does not contain, at the level "All" has many lines of "Calling UIO for ..." with the result of "Status code is 200".
    When printer as networked - this is no problem - Jetadmin shows everything including toner's level.
    Does HPWSProxyService_10_3_1 support status of supplies (toner level) for printer HP LaserJet M1536dnf MFP?

    Bump.
    Does no one else use this printer and Web JetAdmin?

  • Connecting Printer and HDD to Airport Extreme (windows)

    I have gone step by step and the bonjour keeps freezing when I tell it to finish the printer setup. The computer will recognize the printer but will not print. I also tried connecting a usb hdd to the AE and in the utility it shows up but not under my computer. I will say I am pretty dumb when it comes to network drives so a little help would be big!
    Thanks
    Windows vista, soon to 7
    null

    Please check out this excellent article by iFelix on sharing files between PCs & Macs: Sharing files between a Windows XP PC and a Mac running OS 10.4.x

  • Help with printer and displays c?alibration

    Good afternoon
    I need help processing and printing photos.
    My hardware is:
    • Macbook Pro 13 "Intel Core 2 Duo with 4GB Ram 2:53 and running MacOSX 10.6.6
    • Wacom Cintiq 21UX
    • Canon Pixma iP4850.
    I treatment of images in Adobe Lightroom 3; CINTIQ my main monitor, when I compare with the MACBOOK, the images are clearer in this and the printing is always similar to that presented by the MACBOOK. The most obvious option would be using it as primary monitor and guide me through it. But as I have the CINTIQ want to take advantage of it.
    So, I ask:
    • If someone uses the same hardware, what is the best configuration in terms of monitor calibration?
    • What is the best choice of monitor and printer calibrator?
    Thanks

    Your startTimer() method blocks waiting for the thread you started to finish:
    public static void startTimer(String sType, boolean isEnemy) {
            TimerType type = getType(sType);
            TimerThread tt = new TimerThread(type, isEnemy);
            //tt.isPlayable checks that the .wav file was found
            if(tt.isPlayable()) {
                Thread t = new Thread(tt);
                t.start();
                try {
                    t.join();   <------------------  Waits here for thread to finish
                } catch(InterruptedException ie) {
                    ie.printStackTrace();
        }

  • Problem with usb hub 3.0 to connect printer and hd

    Hello,
    I have problems with using a usb 3.0 hub to connect a HD and a printer to my Time Capsule. HD is found and works properly. Printer is visible in programms but doesnot work.
    How to fix this.
    Ciao Pieter

    OK, plug the hub back in with the printer.. delete the current setup on the computer and try reinstalling it.
    But it tells you something if the printer is not recognised..
    Why don't you just share it from the computer.. USB printer are not supposed to be plugged into a network device. They are designed as local printers.

  • Need help connecting an iPod Touch to WRT54G

    I have a WRT54G version 6 router.  My laptop finds the network and connects easily.  My new iPod Touch finds the network, I enter the password (I'm using WPA), it looks like it is connected, but all the settings are blank.  I have used the iPod at a coffee shop with wifi, so I know it can work.  What do I need to do?

    Try to use WEP Security on your router as your IPod must not be configured to accept WPA securty...Once you set WEP security , if prompted for a wep key on your IPod enter a dollar sign($)and then enter your wep key and attempt to connect, if it does not connect just enter the wep key without the dollar sign and it should connect...

  • Need help - connecting Monitor and TV at same time with component video

    I have a mac mini, connected via DVI to a monitor - I bought a DVI splitter to connect the monitor to one port and the tv to the other via a DVI to Video adapter, using component video. When I plug in the DVI to Video adapter, the primary monitor loses its connection and I cannot seem to get the TV to recognize the signal - what am I doing wrong?

    In my case, the Barco Cine7 CRT projector I would like to connect the new Mini to accepts a pretty wide variety of analog component video formats, but I cannot find a listing of what the Mini supports. Presuming I use a DVI to VGA adapter and then a VGA to RGB cable, can the mini video card output any one of the following analog component formats:
    RGBs or RGsB - R, G and B with automatic sync detection between seperate sync (separate composite sync or with separate hor and vert. sync) or sync on green (composite sync)
    RGB with tri level sync - R, G and B with separate tri level sync or with tri level sync on green.
    Component video - R-Y, Y and B-Y with separate sync or with compositesync.
    Component video with tri level sync - R-Y, Y and B-Y with separate tri level sync or with composite tri level sync.

  • Connecting printer and internet via ethernet port

    My iMac has only one ethernet port, and previously I had the printer hooked up to it. Now we have high speed internet but it requires the same port. When we try switching back and forth, the internet still works but the printer doesn't.

    Hi
    I would recommend that you invest in an inexpensive router, which should include a number of (commonly 4) ethernet ports. This will live between your high-speed modem and all your network devices, including your computer and your printer. You can then, of course, add more wired computers , and they will all be able to access the printer.
    D-Link and Linksys are decent brands for simple home routers.
    Matt

  • I just purchased by MacBook Pro and I need to connect it to my HP officejet 6500 wireless printer, I tried putting the disk from the printer and I was not able to connect the two can you help me.

    I just purchased my Mac Book Pro and I need to connect it to my hp officejet 6500 wireless printer, I tried using the CD that came with the printer and it will not connect

    Very glad you added that bit of information because I see different problems similar to this.  I want to share with them what you did and hopefully you not only fixed your specific problem but you can lend some more advice to others with problems like this. Thanks!
    Don't forgot to say thanks by giving "Kudos" if I helped solve your problem.
    When a solution is found please mark the post that solves your issue.
    Every problem has a solution!

  • HT4356 I can see my printer and iPad on router but iPad cannot connect to printer. Printer is on list of air printer models accepted. Help!

    I can see my printer and iPad on router but iPad cannot connect to printer. Printer is on list of air printer models accepted. Help!

    You may have to visit the printer manufacturer's web site and look into their support pages to get a print driver for your Mac, and install it. Or see if you can see if a driver may already be in your Mac by checking settings, since there are many drivers already installed in Mac OS X.
    Good luck & happy computing!

  • Need help connecting to network printer using xfce and cups

    Hello
    please can someone assist me with setting up a printer.
    I am running arch and xfce desktop.
    I have an Epson Stylus Photo R800 USB printer connected to a wireless Belkin all-in-one Print Server.
    I do not know how to connect to this printer.
    I am not conversant in CUPS or network printing and would very much like to use the printer.
    My arch box is connected through cable to a wireless router.
    The print server is connected to the wireless router and the router confirms the print server is attached to the network.
    The print server IP address is 192.168.0.100.
    The printer server has a web interface which I used to set wireless and TCP settings. I should say that I went into this interface and configured the print server which is totally usable and fine from a Vista laptop using wireless - vista laptop "sees" the print server and prints over wireless, therefore I know the server and printer are working together and all the print server settings are fine. I dont know how Vista connects, it just does!
    I tried installing gutenprint and foomatic, went into the CUPS server page (localhost:631) and found my printer but I'm not sure if my connection string (socket://192.168.0.100:9100) is correct. I've tried several values and several Epson drivers from the CUPS web interface, all to no avail. I just get this message:
    bash-3.2# lpstat -t
    scheduler is running
    system default destination: Epson
    device for Epson: socket://192.168.0.100:9100
    Epson accepting requests since Sat 26 Jul 2008 22:53:35 BST
    printer Epson now printing Epson-0. enabled since Sat 26 Jul 2008 22:53:35 BST
    /usr/lib/cups/filter/pstoraster failed
    I have no desire to be a CUPS expert nor a networking expert - I was rather hoping someone could guide me through the process, I have tried reading web links (google) but do not understand various pages and instructions.
    bash-3.2# cat /etc/cups/printers.conf
    # Printer configuration file for CUPS v1.3.8
    # Written by cupsd on 2008-07-26 22:34
    <DefaultPrinter Epson>
    AuthInfoRequired username,password
    Info Epson
    DeviceURI socket://192.168.0.100:9100
    State Idle
    StateTime 1217108079
    Accepting Yes
    Shared Yes
    JobSheets none none
    QuotaPeriod 0
    PageLimit 0
    KLimit 0
    OpPolicy default
    ErrorPolicy stop-printer
    </Printer>
    any ideas good folk?
    Last edited by keratos (2008-07-26 22:07:45)

    EDIT:
    SOLVED!
    the problem was that gutenprint needed to be installed.
    I looked at the rastertops file in /usr/lib/cups/filter and it was very small, handfull of lines, but refered to gutenprint (whatever that is).
    "pacman -Q gutenprint" revealed it was not installed.
    All is fine now.
    GREAT!

  • IPod Nano 5th Gen Help: When I connect my iPod to my PC it seems to connect fine and show as normal until I load up itunes. Why is it suddenly not being recognized once my itunes is loaded?

    Hello, I've been working at this for hours but have made little to no progress in fixing my issue.
    So when I plug my ipod in via usb into my computer the autoplay starts and it connects as an iPod. I can see it when I open up "Computer" and everything seems to be running fine. I'm not getting any errors or anything.
    However, the moment itunes starts up, whether it be manually started or starting automatically through the helper, my symbol for safely removing falls off of my screen and I can no longer see the ipod in "Computer". Though I may be able to see it in Printer and Devices.
    I've already gone through several steps to try and fix it via support on this site. I've reinstalled itunes, I've gone into disk mode, I've reset the ipod, unplugged it and replugged it in. My last option is to restore to factory defaults. As much as I would love to do this to see if it works (as all my music is backed up on discs and my computer), I can't do so if it isn't showing in itunes due to the fact it can't detect the ipod or at least the kind of ipod. I've tried to find a 3rd party program that could do this but none of them offer the option. Note: The ipod itself works fine. I can listen to it and it'll charge just fine. It just won't recognize.
    I'm running Windows 7 OS. iTunes is up-to-date.
    If anyone knows how to fix it, the help would be greatly appreciated.

    Hello BPeery,
    I would go through ALL the steps here:
    iPod not recognized in 'My Computer' and in iTunes for Windows
    Let us know how it goes.
    Hope this helps.
    ~Julian

  • Wireless printer and wifi wont connect at same time

    Hello
    I have a Mac Mini with software version 10.6.8  I also have a HP wireless printer and for some reason cannot get my wirless internet and wireless printer to connect at the same time,  to print anything I have to disconnect from the internet and to use the internet I have to disconnect from the printer can anyone help?
    Many thanks,
    Kiera

    It sounds as though you did not configure your wireless printer to join your usual wireless network. It may be communicating directly with your Mini using an "ad-hoc" configuration, bypassing your wireless router. This will be inconvenient at best.
    Refer to your HP printer's documentation to determine how to configure it to join your existing wireless network... the same one you use to connect to the Internet.

  • HP Officejet pro 8500 won't print and keeps asking for a proxy setting. Help.

    HP Officejet pro 8500 won't print and keeps asking for a proxy setting. Help.

    Hi,
    Can you confirm that you have an Officejet 8500a or Officejet 8500? On the 8500a model, you can set the networks proxy address and port setting from the front panel of the printer (setup>Webservices setup>proxy). If you are unsure what your proxy settings are you'll need to contact your network admin. If your network uses a proxy users name and password for all devices, you need to enter this information along with the proxy address and port in the printers embedded web server. Type the products IP address into an internet brownser window (printer must be connected to the same network as PC). Select the network tab, and than look for the proxy settings option. Enter in the information and click apply. Once the networks proxy information has been correctly inputed into the embedded web server, try printing again. If unsuccessfully, you might try reinstalling the printer software after uninstalling it. Hope this helps!
    I was an HP employee
    Reminder: Please select the "Accept as Solution" button on the post that best answers your question. Also, you may select the "Kudos" button on any helpful post to give that person a quick thanks.

  • HP Print and Scan Doctor can't connect to HP Officejet Pro 8600 Plus.

    My HP Officejet Pro 8600 has been working perfectly for the last 1+ years, up until 2 days ago, when it stopped printing jobs submitted from my Windows 7 desktop.  I've tried all manner of repair, thus far unsuccessfully, including
    resetting the IP on both the printer and the desktop
    trying wireless connection, no difference
    reinstalling drivers and firmware
    hard-resetting the printer
    repeatedly trying to print test pages
    repeatedly restarted the Print Spooler, and rebooted the desktop
    attempting to troubleshoot using HP Print and Scan Doctor.
    Additional facts:
    My wife can use the printer from her work laptop without any problems.
    I can ping the printer from the desktop at its static IP, so IP-level connectivity isn't the problem.
    The standard print queue view indicates "(Offline)" in the title bar, and attempting to print a test page from the Properties dialog submits the page, then Status flips to "Error - Offline - Printing", despite the fact that the Properties dialog shows no checkmark next to Use Printer Offline menu entry.
    The Doctor finds the printer at its IP and acknowledges that it's installed, and when asked to Fix Printing, says that everything checks-out okay with the product.  However, when I ask it to Test Print, it comes back with a pop-up stating it's Unable to Communicate with Printer; it suggests "Click Help for additional assistance information.", but there's no Help button.
    If you've experienced this printer in a similar firmly-wedged state, I'd deeply appreciate hearing how you fixed it.
    Thanks,
    -Richard (Personal information)

    Hi @Sunshyn2005
    I timed-out waiting for advice, and contacted HP Support, who helped me get the printer back on the air.  While we didn't manage to root-cause it, in the course of trying various things, the tech disabled Norton 360's firewall, which then allowed connecting to the printer, and restoring print service, which remains up after re-enabling the firewall. 
    The timing of the disconnection doesn't neatly corellate with any Windows updates.  My own theory is that it was caused by a 360 update, but am unable to find a smoking gun, since 360 doesn't provide update history.  The exact root-cause remains a mystery, but at least provides another thing for folks to try should they find themselves in similar straits.
    I really appreciated your hint that a Windows update might be the root cause, and your pointing out how to review the history and back-out updates: this morning, I found that Windows had installed a batch of updates overnight, and found that no browsers worked.  Using your advice, I rolled back the update, restoring browsing.
    Thanks,
    -rjs

Maybe you are looking for