Help finding router settings.

I have a WRT54G V.6, and I need to reset it because the password was lost. In the reset guide, it tells you take note of it's current settings, but I can't seem to do it without the password. Is there any other way to find the settings?
I'm an online gamer, so my connection quality is extremely important.
Solved!
Go to Solution.

It depends on your ISP's settings.
For DSL, follow this procedure.
For Cable, this procedure should get you going.

Similar Messages

Need help finding overclocking settings in BIOS on my Z97 Gaming 7

Hello Folks!
As the title states I need some help finding some settings in the BIOS to help in overclocking on my awesome new MSI Z97 Gaming 7 mobo! For instance I can't find anything related to Load Line Calibration, LLC. I am unable to find additional settings for PLL and what the settings that are there do, for instance CPU PLL, the options are something like LL and SB? There is no explanation for what either of these are. These may be pretty basic things in overclocking Intel. I should also mention that I am new to Intel processors and their mobo's. I have always used AMD cpu's and overclocking seemed a bit more straight forward. This is also the first MSI motherboard I have owned so I am also new to these. I have been a great fan of MSI GPU's for years and finally had the chance to buy a motherboard and while it has been a great experience thus far I seem to be slighty behind the learning curve here. I do appreciate all the help I am able to get. I have read the guides that I have seen others pointed towards and have not really found the information I am looking for there.

Nichrome, thank you for the heads up concerning placing my rig info into my signature, I will do that immediately. Thanks for trying to help. I really do appreciate it. I am very familiar with overclocking on the AMD platform. I have previously owned and abused the PhenomII 965BE, 1055T FX-8320 and FX-8350. I guess switching from AMD to Intel and being confronted by so many new terms and settings in the BIOS I was kind of lost. I wasn't really too concerned with the PLL per say other than just desiring to know as much about my new system and motherboard as possible. I have always been a firm believer that to get the most out of your equipment you need to know it intimately, I guess I will get there with a bit of time and perseverance! I was really mainly trying to figure out where the LLC settings would be hidden or what they would be known as with an Intel based system, this setting is usually quite important when trying to stabilize higher overclocks. I am currently running and tinkering with an OC speed of 4.7-4.8GHz @ 1.275v with temps staying ~55C. I was hoping to push a little further and was trying to give myself the best possible advantage in doing so. Again, thanks for the help and information!!!

HELP PLEASE ROUTER SETTINGS

Hi, i cannot access my router settings through my browser i know the ip address I'm suppose to go to in my browser but when it asks me for my user i don't know what it is nor my password. I already changed my password on my router do i use that to access my router settings through the internet? i tired to use my router password for the password for the settings but it doesn't work? What am i suppose to but as my dam password and username. When i use my laptop to connect to my router its shows up as EDDIELAN that is what it shows up as when i searched for wifi connections on my laptop. Am i suppose to use EDDIELAN as my user and the password on my router for the password on the setting pagee?
Also currently my router i think has a time when i can use my internet. For example i can't use my internet between 3:30pm and 7:00 pm. How do i disable that crap so i can use my internet anytime i want? Can i control the time i use my internet through the settings? Somebody has set this in my router and i know how have to get rid of it! i want to be able to use my internet when ever i want! help please how do i disable that?

As the password of the router is not working..You have to reset the router for 25-30 seconds and then,try to access the router setup page...Once you reset the router,all the settings on the router will go to factory default...Now,you can configure the router from scratch.

Router Settings Help

I'm wondering how I get to my router settings (on the browser, not system preferences).
I've tried entering my IP address into the address bar, but that didn't work.
I'm trying to switch the channel my internet is on, because it's interfering with my phone.
If you don't know what I'm talking about.. it should look something like this >>
http://tinyurl.com/33fsack
I don't know if I can change this "channel" on the airport settings, but any help will be appreciated.

You need to experiment with different channels settings.
AirPort Utility > Manual Setup
Wireless tab/label just below the icons
The Channel setting is on this page. It's probably on Automatic now. Try some manual settings to see if you can find a better channel with less interference.

HT4623 I can't find the hotspot settings it's gone after update to ios7 can anyone help find the download ?

Can someone help find this download problem for the iPhone 5 updated to iOS 7?

It is not gone, the carrier must support the feature.
Does your carrier support the feature?

ARD 3.3 slow screen redraw - are there special router settings ?

Hello all !
I think I read somewhere on previous Google searches about special router settings to help ARD run as quickly as possible.
I connect to an external site via an intermediate machine in a DMZ area for security (Network Group stipulation) and have found ARD 3 to be sluggish on a line that has actually been upgraded from 2MBit to 10 MBit ...
I am ARDing from my machine to another also running ARD to then get to the site ...
I also recall version 2 of ARD "seemed" to be better redraw then this version ...
Mitch

So is NO ONE experiencing this?
I find that hard to believe...

Need to know how to reconfigure router settings

Hi - I was online with tech support for an hour before they told me that they couldn't help me unless I paid them or bought a new router. Neither is an option for me financially so I hope that someone can help. :-(
My cable signal went out very briefly, probably for 5-10 seconds. When it came back, my router was no longer working. I jumped through all the reset hoops that normally work, but nothing worked this time. The tech guy said that I needed to reconfigure my router settings. I don't know how. Can someone here help me?
I am running Windows Vista and the router is a Linksys E1000, version 2. Is there a page on this site that tells me what to do? I couldn't find it.
Thank you SO much for any help that you can give me. I'm desperate!
Solved!
Go to Solution.

Hi! You have to access the setup page of the router to reconfigure the settings. This link should help you: http://www6.nohold.net/Cisco2/ukp.aspx?vw=1&docid=0ff4c94586a345d082828ec2161aaecf_3686.xml&pid=80&r.... Before doing the steps though, reset your router by pushing the reset button on the device for 15seconds.

WRT310N: Help with DMZ/settings (firmware 1.0.09) for wired connection

Hello. I have a WRT310N and have been having a somewhat difficult time with my xbox 360's connection. I have forwarded all the necessary ports (53, 80, 88, 3074) for it to run, and tried changing MTU and what-not.
I don't know if I have DMZ setup incorrectly, or if it's my settings.
Setup as follows:
PCX2200 modem connected via ethernet to WRT310N.
The WRT310N has into ethernet port 1 a WAP54G, and then upstairs (so that my Mother's computer can get a strong signal) I have another WAP54G that I believe receives its signal from the downstairs 54G.
In the back of the WRT310N, I have my computer connected via ethernet port 3, and my Xbox 360 connected via ethernet port 4.
Now, I first figured I just have so many connections tied to the router and that is the reason for being so slow. However, when I unplug all the other ethernet cords and nothing is connected wirelessly, except for my Xbox connected to ethernet port 4, it is still poor. Also, with everything connected (WAP54G and other devices wirelessly) I get on my PC and run a speedtest. For the sake of advice, my speedtests I am running on my PC are (after 5 tests) averagely 8.5 Mbps download, and 1.00 Mbps upload, with a ping of 82ms.
Here is an image of the results:
http://www.speedtest.net][IMG]http://www.speedtest.net/result/721106714.png
Let me add a little more detail of my (192.168.1.1) settings for WRT310N.
For starters, my Father's IT guy at his workplace set up this WRT310N and WAP54G's. So some of these settings may be his doing. I just don't know which.
"Setup" as Auto-configurations DHCP. I've added my Xbox's IP address to the DHCP reservation the IP of 192.168.1.104. This has (from what I've noticed) stayed the same for days.
MTU: Auto, which stays at 1500 when I check under status.
Advanced Routing: NAT routing enabled, Dynamic Routing disabled.
Security: Disabled SPI firewall, UNchecked these: Filter Anonymous Internet Requests, Multicast, and Internet NAT redirection.
VPN passthrough: All 3 options are enabled (IPSec, PPTP, L2TP)
Access Restrictions: None.
Applications and Gaming: Single port forwarding has no entries. Port Range Forwarding I have the ports 53 UDP/TCP, 88 UDP, 3074 UDP/TCP, and 80 TCP forwarded to IP 192.168.1.104 enabled. (192.168.1.104 is the IP for my xbox connected via ethernet wired that is in DHCP reserved list)
Port Range Triggering: It does not allow me to change anything in this page.
DMZ: I have it Enabled. This is where I am a bit confused. It says "Source IP Address" and it has me select either "Any IP address" or to put entries to the XXX.XXX.XXX.XXX to XXX fields. I have selected use any IP address. Then the source IP area, it says "Destination:" I can do either "IP address: 192.168.1.XXX" or "MAC address:" Also, under MAC Address, it says DHCP Client Table and I went there and saw my Xbox under the DHCP client list (It shows up only when the Xbox is on) and selected it.
Under QoS: WMM Enabled, No acknowledgement disabled.
Internet Access Priority: Enabled. Upstream Bandwith I set it to Manual and put 6000 Kbps. I had it set on Auto before, but I changed it. I have no idea what to put there so I just put a higher number.
Then I added for Internet Access Priority a Medium Priority for Ethernet Port 4 (the port my xbox is plugged into).
Administration: Management: Web utility access: I have checked HTTP, unchecked HTTPS.
Web utility access via Wireless: Enabled. Remote Access: Disabled.
UPnp: Enabled.
Allow Users to Configure: Enabled.
Allow users to Disable Internet Access: Enabled.
Under Diagnostics, when I try and Ping test 192.168.1.104 (xbox when on and connected to LIVE), I get:
PING 192.168.1.104 (192.168.1.104): 24 data bytes
Request timed out.
Request timed out.
Request timed out.
Request timed out.
Request timed out.
--- 192.168.1.104 data statistics ---
5 Packets transmitted, 0 Packets received, 100% Packet loss
Also, when I do Traceroute Test for my Xbox's IP, I just keep getting:
traceroute to 192.168.1.104 (192.168.1.104), 30 hops max, 40 byte packets
1 * * * 192.168.1.1 Request timed out.
2 * * * 192.168.1.1 Request timed out.
As for the Wireless Settings, it is all on the default settings with Wi-Fi Protected setup Enabled.
To add, I have tried connecting my modem directly to the Xbox and my connection is much improved. I have no difficulty getting the NAT open, for it seems my settings are working for that. Any help with these settings would be VERY much appreciated.
Message Edited by CroftBond on 02-18-2010 01:09 PM

I own 2 of these routers (one is a spare) with the latest firmware and I have been having trouble with them for over a year. In my case the connection speed goes to a crawl and the only way to get it back is to disable the SPI firewall. Rebooting helps for a few minutes, but the problem returns. All of the other fixes recommended on these forums did not help. I found out the hard way that disabling the SPI Firewall also closes all open ports ignoring your port forwarding settings. If you have SPI Firewall disabled, you will never be able to ping your IP from an external address. Turn your SPI Firewall back on and test your Ping.
John

Airprint no longer working – router settings wrong?

Airprint no longer working – router settings wrong? Network TP-Link TD-W8951ND router. version 5.1, Firmware build 120522. As far as I know the settings are factory defaults with two exceptions. My ISP input various settings to reflect my proper internet connect configuration. I have assigned one static port “100” to a printer not currently on the network. Auto DHCP now starts at “101”. Epson Artisan 837 printer. New, Bonjour service name EPSON3FC9CA (Artisan 837), auto IP address (currently 192.168.1.103), firmware WB15D3 38.38 linked wirelessly not by Ethernet. iPhone 4S Software 6.1.3 (10B329). iPad 3 Software version 6.1.3 (10B329) Windows Vista 32-bit laptop, linked wirelessly, auto IP address Windows 7 64-bit desktop, linked via Ethernet, auto IP address MagicJack Plus, linked via Ethernet, auto IP address Installing Epson On June 6, 2013, using my laptop, installed it wirelessly on my network. Updated firmware etc. All worked well. Same for the desktop. Again all functioning as planned. The installed printer name was Artisan 837 (Network) When I tried to use the Airprint function on my iPhone it could not find any Airprint printers. I downloaded and ran the Bonjour print services wizard. This created a printer named EPSON3FC9CA (Artisan 837). I could now print wirelessly as planned. Problem solved I thought. As of June 6, 2013 all software and firmware is current. On June 12 attempted to link my iPad to Airprint for the first time. It could not find an Airprint printer. I tried my iPhone and it could no longer find an Airprint printer. I tried numerous powerdowns, reboots, reinstalls etc. to no avail. I can point Safari wirelessly to the printer IP address on both iPhone and iPad and see the printer’s “web page” to check ink level, settings etc. I downloaded Epson iPrint to both iPhone and iPad and that software works as planned allowing wireless printing. I tested the Epson on my older Linksys router and my iPad found it as an Airprint printer! Worked wirelessly as planned. Conclusions The only thing that is not working as planned is Airprint functionality on my TP-Link network. I am thinking there is a setting on the TP-Link router that needs to be adjusted to keep the Bonjour established software path open and persistent. From the time I first established the Airprint connection to the next time I tried to establish a connection was some 6 days. Although the iPad and iPhone renew their network lease every 90 days, the other equipment lease runs for 3 days before renewal. I don’t know if the IP address of the Epson changed on renewal. (Even if it did, I would hope the discover functionality should follow to the new address.) Over that 6 day period there were no software or firmware changes. As far as I know the only environmental change would be related to IP addresses or something else at the router level severing the connection. Before trying a static IP setting for the Epson (and I don’t know if that will work) are there any other router settings to check that will clear up this situation? I am sending this to TP-Link, Epson, Apple, and my ISP in hopes that a solution can be found.

Thank you for your reply. What I didn't mention was that I have spent days googling to find an solution. I have tried most alternatives suggested to no avail. My problem is quite technical and most probably has a very specific and simple solution related to my router (set ABC to 123XY). All alternatives ended, "if this doesn't work contact the supplier". So I have - Apple (here), Epson, TP-Link and my ISP. When (if?) I find a solution I'll post it here for others to learn from.

Search Help for ROUTE field in VA01

Hi All,
I need help in assigning search help to ROUTE(VBAP-ROUTE) field in VA01 Transaction.Instead of standard F4 list I need a list of Routes from the Custom table which will be maintaned.This new F4 list has to be displayed based on order types...Means only for order type ZXXX it should show the new F4 List, for the rest of the ordertypes it should show the standard F4 List.
P.S : Search help H_TVRO is assigned to the Route.This Search help doesn't have Search help Exit or Append Search help options.
Your help is highly appreciated.
Thanks.
Satyan.

Hi,
You can do that using search help exits you would find several threads already posted to the forum for this like below:
Link[Search Help Exits|Search Help Exit;
Regards,
Himanshu

Verizon Quantum Gateway Router settings issue related to printing and wifi cameras?

Hi,
I have a Verizon Quantum Gateway router and I just did a fresh install of Windows 8.1 Pro x64 and am downloading and installing my printer drivers. I connect the printer to the wifi network, 100% sure it is connected and settings are set to wireless lan. I've had this printer for a while. Doing the setup - it cannot find the printer.
Related: I bought a 2 pack of Motorola Focus66 wifi cameras to watch my dogs when I'm gone. I can connect to the cameras when I'm on my ipad's Verizon Wireless LTE connection, but when I'm at home connected to my same Verizon Fios wifi I cannot view cameras. Yes - the camera and apps support local and remote connections.
I have turned the firewalls all the way off and this does not fix the problems, so I'm believing it is in the router settings. Any suggestions?

I had a wifi network running at my house with a PC, Laptop, 5 iphones an iPad, and an XBox all running with no issues.. I got the "Upgrade" of the Gateway router and I can connect those devices to the network but WiFi printing is screwed up and Air Printing the apple devices is totally dead.. cannot see the printer. The customer support are completely a waste.. they suggested I pay for "Premium Support" At this point I've invested a solid 10-15 hours trying to get this setup and talking to Verizon and its just a mess.

How to find the settings in ProcessChain

Hi All,
One of the Process Chains is updating data in BW two times in a day(not periodic with different timings).
When i have checked the backgroundjob(BI_PROCESS_TRIGGER) for that Process Chain it triggered only once in a day whereas when i have checked just one infoPackage in chain it is triggering 2 times in a day.
Since my requirement is to set another chain as like above chain (same) i am unable to find the settings how it has done.
i have checked option for that infoPackage in Schedule tab we are using Start Data Load immediately(Scheduling options grayedout)
I also checked where used list in the Tab it is used in One Chain only
Can anybody help me.
Regards,
Chakri
Message was edited by:
Chakri

Hi Chakri,
Goto the infopackage -> scheduler tab -> click the scheduling option and remove f any option is there. Now the infopackage would get triggered only through the process chain.
Also check if the same infoapckage is not used in any other process chain by clicking the process chain button in the scheduler tab of the infopackage.
Bye
Dinesh

Help Please -- Routing issue

Hi All...
I have a Linksys WRT54GL Broadband Router.
I have recently signed up for DSL.
I am trying to connect my DSL to the router, but it doesn't seem to work.
My DSL modem assigns 192.168.1.65 ip to my Routers internet interface, with a Subnet mask of /24 and default gateway of 192.168.1.254.
I have setup my Router to be a DHCP server to 3 computers with IP address range of 192.168.10.X (assigned dynamically). The Router's IP address is 192.168.10.1 (that is through which i can configure the router settings).
So my coputer gets ip 192.168.10.100, Subnet mask /24 and default gateway 192.168.10.1.
Now when i am in the routers web interface, i can ping all the websites, using its ping or trace route utility.
But when i try to access a website from my PC, i can't.
When i ping my routers interface ie 192.168.1.65 (that is the ethernet port connected to the DSL modem) from my PC i can but when i try to ping the DSL modems gateway 192.168.1.254 or any other website i cant.
So in a way i can only go as far as the ethernet / internet interface on my router and not beyond that.
Can anyone help me please.

Just did.. and no luck... I disabled Antivirus, and Windows firewall on my PC.. it didn't work.
I tried connecting to the net from the second PC... no luck. Did ipconfig /renew to get a new lease on the second machine.. got a new lease but couldnt connect to the net.
Same issue .... cannot get beyond Routers internet interface.
The routing table on the router looks like this....
Des Lan IP      SM    Gateway                Hop        Interface
192.168.1.0     /24      0.0.0.0                 0         WAN
192.168.10.0   /24      0.0.0.0                  0          Lan&Wireless
0.0.0.0          0.0.0.0   192.168.1.254     0          WAN
I am thinking more on the lines of routing not working, but then again i could be wrong. Any suggestions?Message Edited by japi_s on 05-11-200711:38 PM

IB Routing issue. Unable to find routing to the corresponding incoming msg

Hi All,
We are facing a Routing issue. The flow of message across the DB is given below.
1) Message will be triggered from 3rd party application to PeopleSoft portal with Service Operation A
2) From portal one more service operation B will be invoked to communicate with CRM
Both the service operations are synchronous. I have tested the Service operation in CRM and I am able to get the results. But in Portal if I test, I am getting the error like
+"Unable to find routing corresponding to the incoming request message"+
I have checked the routing alias name between Portal and CRM data bases and Its same.
could you please give us a clue to debug this further?
Thanks,
Hari.A

You should check which permission list the service operation is attached to, and check if the user has been granted to, Something like the following from the backend :
SELECT   distinct c.roleuser
FROM     psclassdefn a, psroleclass b, psroleuser c
WHERE    a.classid = b.classid
AND      b.rolename = c.rolename
AND      a.classid = '<permission_list>' If nothing is returned for your user, then you could created a new role and give it to the user.
Also, since you are on Peopletools 8.52, all this configuration settings can be done through Integration Network WorkCenter. I wrote articles about that (and you can find something about permission list for a given service operation as well) :
http://gasparotto.blogspot.nl/2012/11/peopletools-852-integration-network.html
Nicolas.

'save as' finder window settings and size (on mac)

Hi there ~
Whenever saving/downloading any type of file from any firefox tab, and the 'save as' window opens and I choose where I want the file to be downloaded to, the finder window columns are really tight and narrow, cutting off the folder names so I constantly have to stretch out that first column so I can see the folder names .. this only happens in firefox and the finder window is always squooshed, even if I adjust it and then close/relaunch firefox .. how can I permanently set the finder window settings to avoid having to manually adjust it each time?
thanks

Tom Dignam wrote:
Am I one of a very few who feel compelled to verify a filing after a "Save as" command by having >reopen the Finder?
Probably not the only one... the OS 9 Finder way did slow things down a bit. But it may be a helpful feature for some. Best if you could activate or not. You can file a feature request here Mac OS X Feedback
-mj

Help finding router settings.

Similar Messages

Maybe you are looking for