Help for AUDIGY se installati

Hi! I am a Mac user who is somewhat conversant with PCs. I am about to attempt to install an AUDIGY SE sound card on a friend's PC. (I know, I know, it's a fool's errand) My question is: what do I need to do in order to install this card beyond what are the steps included in the instructions, meaning how do I turn off the old sound card on the mother board? Do I need to reset the IRQ, BIOS or whatever, and how do I even do that? Anything else I need to know and/or do? Any help, particularly the step-by-step, hand-holding variety would be greatly appreciated. Thanks very much. David

Hi,
Try the instructions in the link below:
http://www.soundblaster.com/resource...id=53879&cat=4
Good luck

Similar Messages

Seeking help for PXI card Installation Procedure Guidance

I have PXI-1042 Chassis with PXI Card numbers 2503 MUX , DIO and AIO cards. We are running LabWindows CVI with TestStand 3.0.I have to load all of the above into a new system. I wanna know the step wise procedure i need to follow for using these above mentioned cards w.r.t INSTALLATION process. May i get the document OR link OR any suggestions i need to follow.???
Thank you in advance

I have PXI-1042 Chassis with PXI Card numbers 2503 MUX , DIO and AIO cards. We are running LabWindows CVI with TestStand 3.0.I have to load all of the above into a new system. I wanna know the step wise procedure i need to follow for using these above mentioned cards w.r.t INSTALLATION process. May i get the document OR link OR any suggestions i need to follow.???
Thank you in advance

Anyone have the original software for audigy 4 pro....please help

i?m a frustrated swede without software.... : ) can anybody lay up the original software for audigy 4 pro for downloading...i have lost mine and to get it somewhere else seems impossible...so please ...help me...my email is [email][email protected]][email protected][/url]
if anyone want to mail me!

Problem solved by someone on another Apple forum.

Hope For Audigy Owners? Refund Alchemy Cost? New Drive

Hmm... I couldn't help but noticing the "Audigy Alchemy" sticky has gone walkabout.
I also noticed http://us.creative.com/alchemy/welcome.asp . Complete the forum specifying the email address you used to purchase ALchemy For Audigy. The refund will be made to the credit card that was used for the original purchase. Please allow 30 days for the refund to take place. This offer is valid until 30th June.
The ALchemy application is being provided independent of the drivers, as it is not a driver. The new version of the application works with both X-Fi and Audigy products, and we have added additional updates relating to some popular games that behave differently on the X-Fi chipset guru as compared to the Audigy chipset. We would suggest you download the latest version from CREATIVE.COM when it becomes available.
Thank You.
The Soundblaster Team
Well if there's an Alchemy being released for Audigy series, could there be a possibility of * gasp * working Audigy Vista drivers One that provides 5. would be a nice start.
Perhaps I'm hoping for too much..
I am starting to wonder if somebody is finally listening, though.
Message Edited by Catherina-CL on 05-08-2008 10:11 AM

Hi DriverExpires,
That's correct, the original statement regarding this was made in the feedback sticky thread here.
I have made a quick edit to your post to change the link within the pasted statement to the correct link, but have left the link you included too. This way people are directed to the e-mail form instead of the Guru3D thread, so they can put their information through to us for the refund.
If you haven't already been keeping an eye on the thread I linked above, definitely do bookmark or subscribe to it as it's where we'll be posting or linking any updates/info we get for everyone there (so it's easy to keep track of things).
Cat

Help with Audigy 2 not being fo

Short story: 'Puter C dri've died. Had to put in another and reinstall Windows XP Home. Can't get the Audigy 2 card recognized. Not sure if I have the correct disc. (I love to upgrade and have too many discs.) The discs I have are for Audigy and Audigy 2 ZS. Will either of those work with the Audigy 2 (not ZS) or am I missing a disc? If I am missing the disc how can I get those files? And if it should work, could my Audigy have died, too? Appreciate the help.

ferretguy wrote:
Short story: 'Puter C dri've died. Had to put in another and reinstall Windows XP Home. Can't get the Audigy 2 card recognized. Not sure if I have the correct disc. (I love to upgrade and have too many discs.) The discs I have are for Audigy and Audigy 2 ZS. Will either of those work with the Audigy 2 (not ZS) or am I missing a disc? If I am missing the disc how can I get those files? And if it should work, could my Audigy have died, too? Appreciate the help.
If you lost the CD you find it station-drivers, you just extract them (using winrar) and execute the application mentioned above (can be found on ..\Drivers\support\i386 -folder if you have 32-bit system). Select installation (eg. no uninstallation needed), and allow installation over existing shared files.
.jtpMessage Edited by jutapa on 09-7-2005 07:27 PM

Driver for Audigy Advanced MB for windows 2

Hi,
Will really appreciate if some can provide me a link to download a driver for Audigy Advanced MB for windows 2000
I am novice in computers.
I had purchased a dell M330 system that came with pre-installed drivers loaded and windows vista.
With the system I got a CD.On the CD it is printed as Sound Blaster..... Audigy...Advanced MB.
I changed my OS to Windows 2000 server, now the problem is there is no sound. I tried to use the CD that came with the system, however, the message informs me that I need to install a sound driver. I don't know which sound card I have; but looking at CD I assumed to be Audigy Advanced MB integrated sound card.
I could not find the driver on the your creative website.
Can someone help me.
Thanks

Can someone pls help. Thanks

New Driver for Audigy 2 NX - No 44.1Khz output ?

I installed the latest driver(.0.0099 - 26-Feb-0) for my Audigy 2 NX soundcard running on Windows 7. This the first time I am using the NX on Windows 7.
Everything is working fine, except I notice that in the "Output Rate" dropdown selection (that appears in the Windows "Advanced" tab under Properties of the playback device) there is no option for 6bit 44.Khz. The lowest is 48Khz. So does this mean a 44.Khz signal will always get resampled to 48Khz ? This is for the *analog* output only, not digital(spdif).

Re: New Driver for Audigy 2 NX - No 44.Khz output ?Hi dudl
My name is Felippe from Brazil. I bought an use Audigy 2 NX, that didn?t come with the Instalation and Applications CD. So I started looking for the drivers and applications to install. I installed the beta driver. I managed to install the sound card with it. The problem is the applications. Some of them I did the download (wave studio, creative mediaplayer), but the EAX CONSOLE I couldn?t install. So I tryed to install the Support Pack 3.8 that you published, with no success. The error code is "-6003". As I do not know much about computers, I ask you to help me. I work with music, voice recording, and EAX CONSOLE is really useful, since I do not know any program to replace. Well, I wait your response as soon as possible. Thank you. Felippe
PS: Sorry about my english, ok?!
PS2: You can answer trought the following email: [url="mailto:[email protected]">felippef [email protected][/url]

Creating search help for a field in AdHoc Query

Hi
We have created an infoset based on LDB PCH.
(The infoset contains object type O only).
For the object-id field the users want search help when choosing this field for selection.
Using "start via selection screen" does not give a good solution.
Can anyone explain how I can create search help for fields in an infoset?
Regards
Kirsten

Hi
We have created an infoset based on LDB PCH.
(The infoset contains object type O only).
For the object-id field the users want search help when choosing this field for selection.
Using "start via selection screen" does not give a good solution.
Can anyone explain how I can create search help for fields in an infoset?
Regards
Kirsten

Need to restrict values in F4 help for Batch Characteristic

Hi,
I need to restrict values in F4 Help for a batch characteristic based on values entered for another characteristic. I could not find any BADI or Exit for this purpose. There is a BADI CACL_VALUE which is triggered after an entry is selected from dropdown list but nothing when we press F4. I thought of using Object Dependency but I need to write a programming logic for the requirement. Please let me know if there is any way to write program in Object Dependency or any other way for this requirement.
Regards,
Nikhil

Hi nikhil simha,
first of all, find out which search help is called.
[Hierarchy of the Search Help Call|http://help.sap.com/saphelp_nw70/helpdata/en/0b/32e9b798da11d295b800a0c929b3c3/frameset.htm]
may help you.
If you know the search help, you may enhance it, but first of all you should check the where-used-list and make sure that the search help shows the requested behavior only in the context where you want it to.
If it is your own program, you may be better off to create your own search help and define the triggering fields as search help interface input fields. Then you can use the values to filter results.
Regards
Clemens

Search Help for Vendor Feild not getting populated in the Screen Element

Hi Everyone,
In transaction Miro, I get a POP-UP for Invoicing Party i.e. Vendor and Users required a custom search help.
The Search help for Vendor(LIFNR) is KRED_C and i appended a Z search help under this.
Now that the search help exists and I can drill down the values too but when i select/choose any value, that value is not getting populated in Screen feild.
is there any validation I need to do for this.
Please suggest me... I checked SDN there are many things but i couldn't figure out wat i need to do and where I need to modify.
Regards,
Raj

Dear Hema,
Could you please tell me how many internal tables you are using to store the data for display.
I observerd that you have lt_stock and lt_mat2 declared in the part of the program
>DATA: lv_stock TYPE lty_stock.
>DATA: ltmat2 TYPE TABLE OF lty_mat.
you have displayed above, however you are also using ls_stock and lv_stock .
>IF p_ztotal = ' '. "line
>WRITE 18 ls_stock-matnr.
>WRITE 38 lv_stock-strgr.
>
>ELSEIF ztotal = 'S'.                             "subtotal
    >WRITE: 15 ls_stock-nrmit.
    >WRITE 32 lv_stock-dispo.
    >WRITE 43 lv_stock-fevor.
>ELSE.                                            "total
    >WRITE: 15 'TOTAL'(016), ls_stock-prgrp.
>
>ENDIF.
Are those for displaying some other information?
Also the problem of display you are facing can also be because there are no records to be displayed which satisfies the selection criteria.
Best Regards,
Rajesh.
Please reward points if found helpful.

Search help for SKAT-SAKNR OR SKAT-SAKNR is not working

Hi All,
I have created a Search Help for F4 in a dialog program for SKAT-SAKNR OR SKAT-SAKNR. While i click F4 on that field, it displays blank values.
Here is the module:
module HELP_FOR_SAPGL_ACC input.
CLEAR t_SAPGL.
SELECT SAKNR TXT20
    FROM SKAT
    INTO CORRESPONDING FIELDS OF TABLE t_SAPGL UP TO 1000 ROWS
    WHERE SPRAS = SY-LANGU.
   WHERE L_GL_ACC = v_FIELD_VALUE-FIELDVALUE.
CALL FUNCTION 'F4IF_INT_TABLE_VALUE_REQUEST'
    EXPORTING
    DDIC_STRUCTURE         = ' '
      RETFIELD               = 'SAKNR'
    PVALKEY                = ' '
     DYNPPROG               = PROGNAME
     DYNPNR                 = DYNNUM
     DYNPROFIELD            = 'SKA1-SKANR'
    STEPL                  = 0
    WINDOW_TITLE           =
    VALUE                  = ' '
     VALUE_ORG              = 'S'
    MULTIPLE_CHOICE        = ' '
    DISPLAY                = ' '
    CALLBACK_PROGRAM       = ' '
    CALLBACK_FORM          = ' '
    MARK_TAB               =
IMPORTING
    USER_RESET             =
    TABLES
      VALUE_TAB              = t_SAPGL
    FIELD_TAB              =
    RETURN_TAB             =
    DYNPFLD_MAPPING        =
EXCEPTIONS
    PARAMETER_ERROR        = 1
    NO_VALUES_FOUND        = 2
    OTHERS                 = 3
IF SY-SUBRC <> 0.
MESSAGE ID SY-MSGID TYPE SY-MSGTY NUMBER SY-MSGNO
        WITH SY-MSGV1 SY-MSGV2 SY-MSGV3 SY-MSGV4.
ENDIF.
endmodule.
In the above code I am selecting 1000 rows from SKAT table and in the Search Help Popup it is also displaying 1000 rows but all are blank.
Please help me.
Regards,
Avaneet

Hi check my weblog on search help exit codeing..
https://wiki.sdn.sap.com/wiki/x/du0
\* Prepare for output
CALL FUNCTION 'F4UT_RESULTS_MAP'
TABLES
shlp_tab = shlp_tab
record_tab = record_tab
source_tab = lt_result
CHANGING
shlp = shlp
callcontrol = callcontrol
EXCEPTIONS
illegal_structure = 1
OTHERS = 2.
IF rc = 0.
callcontrol-step = 'DISP'.
ELSE.

I have problem with buying in games , I got the massage that the purchased can not be completed , please contact iTunes support.. I need help for my case please

I have problem with buying in games , I got the massage that the purchased can not be completed , please contact iTunes support.. I need help for my case please

http://www.apple.com/support/itunes/contact/

Search help for date field in Editable ALV

Hello Friends,
I am using editable alv using 'reuse_* '.
I have used date as input field. While creating fieldcatlog also i have declared dat as a mkpf-budat.
But i am not getting serach help for date in output.
Is it possible with reuse or i have to go by object oriented ?

Hi,
Just pass the Edit option of the fieldcatalog for those specific fields...
fcat-edit = 'X'.
CALL FUNCTION 'REUSE_ALV_GRID_DISPLAY'
    EXPORTING
      i_callback_program       = sy-cprog
      i_callback_pf_status_set = 'PF_STATUS_SET'
      i_callback_user_command = 'USER_COMMAND'    "<---- pass this
      i_callback_top_of_page   = 'TOP'
      is_layout                = it_layout
      it_fieldcat              = it_fcat
      i_default                = 'X'
      i_save                   = 'A'
      it_events                = it_event
    TABLES
      t_outtab                 = it_final
    EXCEPTIONS
      program_error            = 1
      OTHERS                   = 2.
*&      Form USER_COMMAND
*       text
*      -->R_UCOMM      text
*      -->RS_SELFIELD text
FORM user_command USING r_ucomm LIKE sy-ucomm
                        rs_selfield TYPE slis_selfield.
CASE r_ucomm.
    WHEN '&DATA_SAVE'.                "<-------check this
      PERFORM save_data.
ENDCASE.
ENDFORM.                    "USER_COMMAND

How to create a F4 help for a report selection screen field

hi,
can any one guide me to create F4 help for a field in a selection screen in a report program,plz give me a sample code

hi,
Here are the following ways
1.with the help of match code objects we can create the F4 Functionality for Field.
Syntax is :
PARAMETERS: p_org LIKE t527x-orgeh MATCHCODE OBJECT zorg.
2. One more thing is we can do it with Search Help's also.
3. Even we can do it HELP Views also.
Help Views:
You have to create a help view if a view with outer join is needed as selection method of a search help
The selection method of a search help is either a table or a view. If you have to select data from several tables for the search help, you should generally use a database view as selection method. However, a database view always implements an inner join. If you need a view with outer join for the data selection, you have to use a help view as selection method.
All the tables included in a help view must be linked with foreign keys. Only foreign keys that have certain attributes can be used here. The first table to be inserted in the help view is called the primary table of the help view. The tables added to this primary table with foreign keys are called secondary tables.
The functionality of a help view has changed significantly between Release 3.0 and Release 4.0. In Release 3.0, a help view was automatically displayed for the input help (F4 help) for all the fields that were checked against the primary table of the help view. This is no longer the case in Release 4.0.
As of Release 4.0, you must explicitly create a search help that must be linked with the fields for which it is offered (see Linking Search Helps with Screen Fields ).
Existing help views are automatically migrated to search helps when you upgrade to a release higher than 4.0.
A help view implements an outer join, i.e. all the contents of the primary table of the help view are always displayed. You therefore should not formulate a selection condition for fields in one of the secondary tables of the help view. If records of these secondary tables cannot be read as a result of this selection condition, the contents of the corresponding fields of the secondary table are displayed with initial value.
<REMOVED BY MODERATOR>
Edited by: Alvaro Tejada Galindo on Feb 15, 2008 3:15 PM

Reg : F4 help for custom fields in ALV report

hi friends..
in my internal table i have fields including 1 custom field..
DATA : BEGIN OF i_final OCCURS 0,
pernr LIKE p0000-pernr,
begda LIKE p0000-begda,
plans LIKE ZPOSITION-plans, (custom)
werks LIKE pspar-werks,
end of i_final.
i want to display this i_final table in alv. for that i genetrate one fieldcatalog
PERFORM fcat USING:
                  'I_FINAL' 'PERNR' 'P0000' 'PERNR' '15' 'X' '',
                  'I_FINAL' 'BEGDA' 'P0000' 'BEGDA' '10' 'X' '',
                  'I_FINAL' 'PLANS' 'ZPOSITION' 'PLANS' '8' 'X' '',
                  'I_FINAL' 'WERKS' 'PSPAR' 'WERKS' '14' 'X' ''.
in custom table zposition, i maintain serch help for custom field "PLANS".
then i used reuse_alv_grid_display.. for all the std fields along wit custom fields
i got f4 all std fields but for my custom i am not getting the f4 help
how can i get the F$ help for this custom fields Zposition-plans..
plz give some idea

Hi
In that Ztable against the field
PLANS give the check table name as <b>T528B</b>
then it will automatically give the search help
or you can create your own search help(elementary) and add to that field
Reward if useful
regards
Anji

Help for AUDIGY se installati

Similar Messages

Maybe you are looking for