Help - fsb probs??

hope you guys can help
my system to begin with!!
msi kt4 ultra bsr
amd t/bred 2400+ (version "b" i believe)
512meg of 333mhz ddr  (cl2.5)
msi ge4 ti4200 128meg
now to my problem - it is my understanding that 333mhz ddr ram should optimise when running at a fsb of 166mhz
unfortunatelyas i slowly up my fsb it crashes out at about 142-4 mhz fsb - even when i use the fuzzy logic it crashes at 144mhz!
i am not sure but as the multiplier seems to be locked on this mobo - is it overclocking the proc too much???
or are there any settings available to allow me to set 166mhz fsb??? with my amd 2400+
please help guys!!!!!
anyone from msi out there listening?? ;-)

Read ....http://www.ocworkbench.com/ocwbcgi/ultimatebb.cgi?ubb=get_topic&f=22&t=000815 .....
Thes guys have alot of knowledge here.... They are not all MSI lovers, but lots of knowledge.... One other note from what I have seen and read some vendors offer 2 version of the 2400+. one locked, and one unlocked....

Similar Messages

  • Help: FSB Setting for MSI 875P with Intel 3.06 533Mhz & Corsair 512 27

    Help: FSB Setting for MSI 875P with Intel 3.06 533Mhz & Corsair 512 2799 333Mhz
    Need a little help here, Intel's specs for the P4 3.06GHz 533 is a multiplier of 23 x 133Mhz.
    However 133Mhz as a FSB seems very slow.
    The 875P NEO has two BIOS settings: CPU Ratio and Adjust CPU Bus
    What are your settings for these - I am quite confused?
    Thanks!
    G.

    133 is the stock FSB setting. set your memory to DDR333.
    Do you want to overclock? you might want to set your memory to DDR266 which is 1:1. so u can adjust a bit of FSB from 133 to maybe 150.
    PS dont forget your memory timing. 2-6-3-3 would be oki i think. what bios version r u using?

  • KT4 Ultra FSB prob! HELP!

    Hey all,
    I'm having an issue trying to get my fsb up to 133mhz w/ the kt4 ultra. It sticks at 100. Also it's detecting my processor speed as a 1500 instead of the 2100xp that it is. I hope you guys can help me, it seems like I'm not the only one to have this problem. My other hardware is great, just moved it over from an old computer. I'm still new at this whole msi thing, so any help would be greatly appreciated. Here's my hardware config too. Thanks guys,
    Justice
    MSI KT4-Ultra BSR
    Antec SmartPower 350w Power supply
    AMD Athlon XP 2100
    Thermaltake CPU fan
    512x1 Mushkin PC2100 DDR RAM
    WD 40 GB Hard drive
    Maxtor 60 GB Hard drive
    Geforce 4 Ti4200 64MB
    Sound Blaster Audigy Gamer
    Linksys NIC card
    Lite-on 32x cdrw
    Pioneer 16x dvd

    Hi,
    Did you set in the BIOS - CPU FSB to 133Mhz?
    Start read here, most probably is cooler location or thermal grease application, as ur PSU seems OK.

  • KT6V AMD 3200+ fsb probs

    hello all.. im pretty much a n00b..
    i recently built a new computer and all, here are some specs..
    MSI KT6V
    AMD Athlon XP 3200+ Barton Core
    Windows XP Pro Service Pack 2
    KingMax PC3200 512mb
    Hynix PC3200 512mb  (total 1gb)
    ATI Radeon 9550 256mb ddr
    SoundBlaster Audigy 2
    Maxtor 250gb HD
    Western Digital 160gb HD
    Samsung Dual Layer DVD Burner
    Power Supply:
    480W; 3.3v   5v   12v
               28a   36a  16a
    i've installed all the latest bios/drivers from MSI, ATI, CREATIVE, etc etc..
    the problem is.. the motherboard auto sets the fsb in the bios at 100MHz giving my 3200+ a mere 1125ghz, at this state windows works fine and everything works.. games such as doom3, half life 2, etc etc..
    ..but
    when i try to change the fsb to what the 3200+ is supposed to be at (200mhz) windows will load only once in a while, and if it does.. it will crash within the first 30 seconds.. crash as in restart or hang.. any other fsb speed between 115 - 200 will result in this same situation..
    i have no idea why my 3200+ wont operate at its supposed fsb.. or anything 115 - 200..
    any help would be great.. and forgive me if this was already addressed in other posts..

    "...MSI KT6V
    AMD Athlon XP 3200+ Barton Core
    Windows XP Pro Service Pack 2
    KingMax PC3200 512mb
    Hynix PC3200 512mb (total 1gb)
    ATI Radeon 9550 256mb ddr
    SoundBlaster Audigy 2
    Maxtor 250gb HD
    Western Digital 160gb HD
    Samsung Dual Layer DVD Burner..."
    Agree with Sharp about the P.S. as we have seen many times this problem in KT6 Mobos. 16A. to 12v. rail is pretty poor with all that power hungry hardware. That would explain why WXP can be loaded only few times at 200 FSB. but have no problems at 100 FSB.- One point that you doesn't mention is CPU/System temps idle/stressed. Can you post them ?

  • F1 help layout prob

    Hi there,
    Can anybody tell me how to maintain the layout of F1 help screen.
    In any places when we press F1 in sap system, there will be screen pop-up. In some systems, we can see function buttons(application help, technical information, etc...)  in the header of screen. And in some other systems, we can see those buttons in the footer of the screen.my question is how can we maintain the layout of this help screen? ( open/close some function, or change the order, or modify the position).
    Any responses will be awarded!
    Thanks and regards,
    Samson

    Can Anyone give me some responses?Plz...

  • PLz help xsl prob

    this problem has been annoying me for a while now.
    I cant see logically what im doing wrong.im trying to select all child nodes of a root node and print the current node
    <xsl:stylesheet xmlns:xsl = "http://www.w3.org/1999/XSL/Transform" version = "1.0" >
    <xsl:template match="/">
    <html>
      <body>
        <fieldset>
          <legend>
            <font face="verdana,arial,helvetica" size="+3" color="#00006B">
                <xsl:apply-templates />   
            </font>
          </legend>
        </fieldset>
          <xsl:apply-templates />
      </body>
    </html>
    </xsl:template>
      <xsl:template match="*">
        <xsl:value-of select="name()" />
      </xsl:template>
      <xsl:template match="/child::*">
        <xsl:value-of select="current()" />
      </xsl:template>
    </xsl:stylesheet>The first template prints the root node name just as i want but the second template will not work.the page is just blank.can anyone help me??i cant find many examples liek this.im trying to write an xslt that can create a standard html representation for any xml file.
    Many thanks

    Look for [email protected] (http://www.mulberrytech.com/) and post it there. Amazing xslt people on that mail list! The author of Saxon Micheal Kay and others answer questions about xslt there.

  • HELP email probs

    I am trying to use my existing sky email address. If I try to set up an email account I go to set up, email icon, internet email account, then I get told that "your device had a problem connecting to the server" ? I do not understand, who's server?. I have also tried to set up a Blackberry ID but I keep getting told " the Blackberry ID user account service is not reachable please try later" I have several times with no luck.
    All I want is to view my emails ..................................

    Hi fattylewis
    Do you have the correct BlackBerry data plan with your wireless provider?  I would recommend contacting them to ensure you are set up correctly.
    Thanks
    -CptS
    Come follow your BlackBerry Technical Team on twitter! @BlackBerryHelp
    Be sure to click Kudos! for those who have helped you.Click Solution? for posts that have solved your issue(s)!

  • Help ipod prob

    i need help i got a new ipod 30 gig video ipod.
    I can fully charge it and unhook it turn it off and the next day the battery will be dead.
    When listening to it i get standard listing time so i don't know what is wrong.

    For any unexpected battery drain the first thing to check is that an alarm is not set that would cause the iPod to start up and play whilst unattended.
    To check go to extras/clock/alarm and set it to off. Check the calendar also, extras/calendar/alarm.

  • Help! Prob with CSS display

    I created 3 different local sites for possible web pages
    using CSS. I can still view the sites in browsers - have headings
    with logos, horizontal naviation bars etc - but in display view
    they revert to writing( eg the original unordered list). I cannot
    even remake them. What did I do? How can I correct?

    VIEW | Style Rendering > Display Styles
    Murray --- ICQ 71997575
    Adobe Community Expert
    (If you *MUST* email me, don't LAUGH when you do so!)
    ==================
    http://www.projectseven.com/go
    - DW FAQs, Tutorials & Resources
    http://www.dwfaq.com - DW FAQs,
    Tutorials & Resources
    ==================
    "hnajskmei" <[email protected]> wrote in
    message
    news:ggbh24$895$[email protected]..
    >I created 3 different local sites for possible web pages
    using CSS. I can
    > still view the sites in browsers - have headings with
    logos, horizontal
    > naviation bars etc - but in display view they revert to
    writing( eg the
    > original unordered list). I cannot even remake them.
    What did I do?
    > How can
    > I correct?
    >

  • Zen micro help, serious prob

    After accidnetly removing my battery while music was still playing my zen micro is not allowing me to go any further then a screen that says "hardware problem". I cant turn my player off, everytime i take the battery out all that comes up when i put it back in is the same screen sayin hardware problem. My computer now does not recognise my player. What shall i do ?

    Call Customer Service.. doesn't sound good.

  • TS1717 Getting two error messages when trying to access I Tunes on my Windows 7 Computer:  Windows Error 126 and MSVCR80.dll not found

    Having difficulty accessing I Tunes on my Windows 7 Vista.
    Error messages are two fold:
    1. MSVCR80.dll not found.  Reinstall may help correct prob.
    2. Windows Error 126. 

    Uninstall your existing copy of iTunes. Delete any copies of the iTunesSetup.exe (or iTunes64Setup.exe) installer files from your downloads areas for your web browsers and download a fresh copy of the iTunes installer from the Apple website:
    http://www.apple.com/itunes/download/
    (The current build of the 11.1.4.62 installer was changed a few days ago, which fixed the bulk of the reports of MSVCR80.dll/R6034/APSDaemon.exe/Error-7/AMDS-could-not-start trouble ... but the build number on the installer was not changed. So we're trying to make sure you do the reinstall using a "new good" 11.1.4.62 installer instead of an "old bad".)
    Does the install with the new copy of the installer go through properly? If so, does that clear up the error message?
    If you still have the same error messages cropping up, then try the procedures from the following user tip:
    Troubleshooting issues with iTunes for Windows updates

  • Trying to find out cause of game crashes

    Lately I have been playing CS: Source.  It seems like more frequently now, when I load into the game (meaning when I finally get to the playable portion of the game) my monitor shuts off after about 3 seconds of seeing the game and then the computer freezes right after.  If i restart and try and run the game I get the same problem, I have been able to start the game after 3 or 4 restarts and had no problem playing for hours.  Then there are some days when I experience no problems at all, I can play till my fingers are numb.  I do not  have my card overclocked. I have no errors with memtest.
    When I restart and check the temp of my graphics card its at 65 c.
    My best guess is that it is a power supply or graphics card issue.  What are your thoughts.  I am thinking of replacing the psu with this one...any thoughts? would I be better off with a better power supply with lower wattage? (see sig for components in my system)
    cool master

    Quote from: G_man on 17-June-05, 21:59:03
    Just out of curiosity I posted a question on zalman's website in their "Q & A" section about the heatsink moving.  Their response was:
    "Our VF700 is designed to move side to side slightly. It is normal, so do not worry about the performance.
    Thanks!
    Support/Zalman"
    I am really glad now that I did not mess with it.  My temps on my card are now down to 49c Idle on min fan speed which is super silent. Thanks again for everyones help
    No prob man.... That Zalman rocks eh?    

  • CS3: Applying Object styles not always consistent

    Hello,
    I have a number of Object Styles, each of which have different Paragraph Styles called out. In turn, each of these Paragraph Styles calls out different fonts, font styles and sizes.
    Most of the time I can click on a text frame and all the parameters in the Object style are applied--just as it is supposed to be.
    But sometimes the font that the text is supposed to change to does not get applied. This seems to be inconsistent but there is probably an underlying order to it that I do not see.
    So why would an Object style not apply the Paragraph style that is called for in the Object style options?
    Thanks,
    Tom

    I now see the problem, though I do not know the solution.
    If I open up a new document and create a text frame, the font is that old ugly but familiar Times-Roman 12 point.
    But if I open up the template where I have many object, paragraph and character styles, one of each of these is already selected. I can either see this by opening the respective panels or above in the control panel. In fact, any text frame I create always has a top text inset.
    So my Preferences in general are OK and I'd rather not dump them. The problem is that styles are already selected upon opening this one ID file. How do I turn that off?
    In  answer to a question above, I do not simply redo the old Quark file, now in ID. I have a series of styles that are just much easier to apply in a separate ID file, rather than reinventing them in the Quark-to-ID file.
    Thanks for your questions and ideas. They helped me probe this deeper. Now I just need a solution to what I think is a simple problem (still eludes me tho!)
    Tom

  • HFR Very Very Urgent...

    Pls any one help me....
    Hi to all,
    I'm facing a problem In hyperion financial reporting to set the following scenario,pls anyone help me.
    prob is:
    user able to select the period dim options like Qtrly,Monthly,Annual.suppose user select Qtrly,then Q1,Q2,Q3,Q4 only displayed in the column.Suppose he select monthly the columns displays the 12months data.
    thankq

    Hi Ravi
    The problem is that you don't have the option 'Annually', 'Quarterly' or 'Monthly' anywhere in your database so the only way you can achieve this is to use some Member Sets to create this for you. Try the following, it seems to work for me:
    for the Period dimension select OfSameGeneration from the functions tab of the member selection box and then for the member within that function select Current Point of View.
    When a user selects any month on their POV it should return the 12 months, if they select a quarter it should return the 4 quarters and if they select YearTotal it will only return 1 column (If you are using Planning you may need to use the advanced options or conditional suppression to hide the BegBalance column as this will be the same generation as YearTotal.
    Hope this helps
    Stuart

  • Labview 2009 SP1 crashes when moving large selection with arrow key

    If I select a lot (10 or 15) of Block Diagram components and try to move them some distance with the arrow key, I will frequently get a program crash.  Since a smaller number of components seems to crash after a longer travel distance, it looks like some kind of buffer overflow error.  I do not see this problem when using the mouse to move selections.
    I have checked to be sure I have the latest video driver for my NVIDIA Quatro FX570.  I have also tried working with no hardware acceleration and no combined writes.  This is happening on Windows XP SP3 with all the current updates.
    It has become so bad that I have to do a Save As every fifteen minutes to keep from losing data.
    Why don't I use my mouse for all movements?  Because it is not as accurate and not so easy to restrict to one dimension of movement.   My hand is not as steady as it once was.
    I hoping someone will have a suggestion that will clear up this problem.
    Solved!
    Go to Solution.

    As I indicated, I had the same problem with 8.5 and just DID a new installation of Labview 2009.
    Since it is possible my three-monitor setup, which obviously requires more video memory, may be at the root of the problem, I am satisfied with the workaround of dragging the objects near their final destination and then using the arrow keys.  
    Three monitors are ideal for front panel, block diagram and Help/Internet/Probe Window.  When I had to work in the field with only one monitor, I felt severely handicapped.
    You may consider the matter closed.
    Thanks for attempting to duplicate the failure.

Maybe you are looking for