Help - HP Pavilion a6030.uk desktop. Have to press the power button multiple times to start up?
Hi,
I have a HP desktop computer. The model is HP Pavilion a6030.uk, Opertating system: windows vista.
My computer has had no problem at all until yesterday for some reason i had to push the power button multiple times to start it until it finally turned on and did the normal start up. Such as i would press the power button as normal to start it, but all of a sudden, it would turn off after about 2 seconds, and so I would press the power button several times and each time it would not start up and turn off, so the power button would be pressed again until it would finally turn on and start up and run as normal and seems to work fine. And it was the same today, i pressed the power button mutiple times (e.g. 6 times) until it finally started as normal.
As im not very knowledgeable or very computer/technology savvy wise in this area, please will someone help me and give me some advice/help to fix/solve this.
Thankyou for taking time to read this and any help would be much appreciated to resolving this problem.
Thanks.
This question was solved.
View Solution.
Vonbon90, welcome to the forum.
When I see these symptoms on an older computer, I believe that it may be a failed/ing power supply unit (PSU). Here is a guide that will help your troubleshoot it.
Also, you could test the memory. This can be done by removing all of the memory modules and replacing them one at a time and booting.
Please click the " Thumbs up + button" if I have helped you and click "Accept as Solution" if your problem is solved.
Signature:
HP TouchPad - 1.2 GHz; 1 GB memory; 32 GB storage; WebOS/CyanogenMod 11(Kit Kat)
HP 10 Plus; Android-Kit Kat; 1.0 GHz Allwinner A31 ARM Cortex A7 Quad Core Processor ; 2GB RAM Memory Long: 2 GB DDR3L SDRAM (1600MHz); 16GB disable eMMC 16GB v4.51
HP Omen; i7-4710QH; 8 GB memory; 256 GB San Disk SSD; Win 8.1
HP Photosmart 7520 AIO
++++++++++++++++++
**Click the Thumbs Up+ to say 'Thanks' and the 'Accept as Solution' if I have solved your problem.**
Intelligence is God given; Wisdom is the sum of our mistakes!
I am not an HP employee.
Similar Messages
-
P35 Platinum: I have to press the power button multiple times to start
Hello fellow MSI customers,
as written in the subject, I have a problem with starting my PC. When I press the power button, the computer powers on, but there is no output to the screen. In fact, my LCD stays in standby mode. I can hear the fans running, so something is going on. According to the LEDs on the mainboard, it is a memory problem.
Now I turn the computer off, using the power button (have to hold it for a few seconds). When off, I start again and everything runs as it should.
After starting, I ran memtest86 multiple times without any errors. I ran a few games, compiled some programs, installed Vista 64bit, Linux, all without any crashes or hangups. It is just the starting that makes problems. After booting it is very stable.
Seeing that it could be a memory problem, I brought another pair of memory, just to be sure. I couldn't reproduce the problem on that day! Any type of memory I put in (the one before, or the newly brought home) the computer always started on the press of the button. So I thought, OK, maybe they were not seated correctly. But, alas, two days later it is again only starting by pressing the power button three times.
What I tried:
1. Boot using only 1 piece of memory stick
2. Boot using only 1 piece of memory, but different one
3. Use another pair of memory <- worked, but on that day it also worked using my original memory
4. Disconnected everything except graphics card, to make sure it is not a power supply issue (minimized power usage)
5. Tried all of the above with a different processor
6. Used another power supply
Any other ideas?
Here are my specs:
MSI P35 platinum
Core2 Q6600
Nvidia 7900GT
4GB V-Data DDR2 800MHz <--- I think this is the problem, any experiences?
Enermax Liberty 400W
a few other things (HDDs, XFi, DVD-RW)
By the way, how can I boot from an external DVD-RW? It doesn't show in the menu when I press F11 (boot menu).
Thank you for any help, muro
And just to let a bit of steam off:
1. I had major problems with the RAID controller (not MSI fault, rather intel) - I put two disks into a RAID 0, then RAID 1 and they always failed after a few boots - member missing on both disks. I was getting angry, so I put them as normal (non RAID) disks and everything is fine since, although no RAID.
2. Installing anything except windows with an IDE DVD-RW is very hard. It took me ages until I got Ubuntu booting (there are guides on the net, google is your friend), and much longer to get grub (boot loader) working. Long story short - if you have multiple disks, use the Linux disk as the bootable, do NOT put grub on the disk where Vista is installed.
3. I have no idea, how to update the BIOS, if I had to. I'm using 1.1 that came on the board. I use 64bit Vista and Linux, none of which is supported to upgrade the BIOS. Any hints how to do it (if I needed to)?Hello,
now today is the day I've finally received my replacement board. The good news first - it DOES work! Yepeeee!
Now some more information:
The jmicron controller seems to be missing - a screen with something about "Marvel" is shown before the intel raid screen. However, it is only visible for a fraction of second, so I cannot read it. I think it detects my IDE DVD-RW so I'm quite certain it's the replacement for jmicron. I won't miss it - it took me ages to install Linux with the jmicron controller.
The problem where I had to restart the computer sometimes because it didn't even post (RAM error) is gone. It boots just fine now.
I had an extremely long first post - about a minute, but after that it boots very fast now.
anyway, regarding some questions around here - the manual states MSI recommends using an 350W power supply. My 400W is more than enough. Please note - it is an Enermax, not one bundled with a cheap case. My cheap RAM sticks also work very well now. I did try them on different boards before, so now I know I just had a faulty board.
In the end, I can only say this: This is my 3rd board already and it's the first one that works well. As the hardware changed, I presume there were major issues with this board that lead them to make a new revision. What is strange, though, is that the revision is still 1.1, as were my previous two. I pity everybody who had the same problems as I did, but I can now say that I'm very happy about the board now.
Cheers, muro -
rMBP: Sometimes, after having been shut down, i have to press the power button several times before the machine starts up. It's 3 weeks old, and this has happened 2 times now. Is there something wrong with my rMBP?
Did you purchase the Mac new?
You have 14 calendar days from the time your items are delivered to initiate a return as noted here.
Even though you are past the 14 day limit, if it were me, I'd take the Mac back and explain what's going on. Your Mac should work out of the box.
message edited by: cs -
Recently while using my iMac the display will just cut off but the machine is still running and I have to press the power button to get the display to cut back on. What is causing this?
Look in System Preferences/Energy Saver.
-
A few days ago my G5 started to freeze up while in use. It doesn't matter if in Safari, iTunes, Pages, etc. The cursor will not respond nor does any keystroke, force quit, escape, etc. I have to hold the power button down to shut the computer down. Then, try to restart. Sometimes restart will work and the computer will work for a while and then freeze again. Other times on restart, instead of the Apple logo at start up, I get a Zero with a line thru it, have to power off and restart again. When it does restart, the "spinning gear" takes a lot longer than normal to spin up and take me to the login screen. Have been told it may be my hard drive getting ready to fail. Have looked at disk utilities, S.M.A.R.T looks fine, "verified" and have verified disk, and repaired permissions. In case it is the hard drive, I bought external hard drive and hooked it up to Time Machine. The backing up to a long time, overnight, about 10 hours because it kept freexing up and I would have to shut down and try restarting again. Finally got everything backed up.
Any help or suggestions greatly appreciated!!! Could it be my hard drive is dying? Is the the normal chain of events or is it something else???Ok, to copy the Drive from one to another, get carbon copy cloner to make an exact copy of your old HD to the New one...
http://www.bombich.com/software/ccc.html
Or SuperDuper...
http://www.shirt-pocket.com/SuperDuper/
Believe it or not, anything on the Desktop uses 3 times the Resources of the Mac than if stored elsewhere, I can note a slowdown from just 30 items on the Desktop on a really fast Mac, so the less the better on the Desktop.
DW will not tell you about Bad Sectors, it's just the very best at Repair Directory damage & such.
At this point I think you should get Applejack...
http://www.macupdate.com/info.php/id/15667/applejack
After installing, reboot holding down CMD+s, (+s), then when the DOS like prompt shows, type in...
applejack AUTO
Then let it do all 6 of it's things.
At least it'll eliminate some questions if it doesn't fix it.
The 6 things it does are...
Correct any Disk problems.
Repair Permissions.
Clear out Cache Files.
Repair/check several plist files.
Dump the VM files for a fresh start.
Trash old Log files.
First reboot will be slower, sometimes 2 or 3 restarts will be required for full benefit... my guess is files relying upon other files relying upon other files! :-)
Disconnect the USB cable from any Uninterruptible Power Supply so the system doesn't shut down in the middle of the process. -
While I'm using safari, it will freeze up. When I force quit safari and reopen it, I find that I'm back to where I was when I did the force quit and safari remains locked up. When I try to restart the computer, I get a pop up that says that safari cancelled my restart. I then press the power button to shut down the computer. When I reboot the computer and open safari, I see all the tabs and windows that were opened when this issue began, only this time safari isn't frozen. This problem started yesterday.
Has anyone experienced the same problem? Is there a fix for this problem?Try Resetting Safari: Open Safari. Cick on the name Safari in the menu bar. In the drop down menu click Reset Safari.
-
The grayed out start screen that often occurs after the computer's battery has completely ran out occurs twice on my comp. This screen signifies that the computer is waking up from hibernation, so to speak, and I assume of course. This disconcerts me because I would assume that there would be a single progres bar/loading screen, rather than two. If this is normal behavior, please tell me, and if not, do you have any ideas about what I could do to fix this?
Thanks!Batteries
-
I have frequent instances of my Macbook Pro beeping 3 times and then I have to forcefully shut it down by pressing the power button. What is this all about? Please help. Thank you.
I saw this report being sent to Apple:
Interval Since Last Panic Report: 581719 sec
Panics Since Last Report: 10
Anonymous UUID: F4CF708D-D85C-4EC5-8047-4FC22C6B03AF
Fri Mar 7 13:00:14 2014
panic(cpu 0 caller 0xffffff80002d1208): Kernel trap at 0xffffff800020c590, type 14=page fault, registers:
CR0: 0x0000000080010033, CR2: 0x0000000000000000, CR3: 0x0000000007541000, CR4: 0x0000000000040660
RAX: 0xffffff8000000000, RBX: 0xffffff800d35a870, RCX: 0xffffff800cf55cd8, RDX: 0xffffff80008a8fcc
RSP: 0xffffff805e5f3d60, RBP: 0xffffff805e5f3da0, RSI: 0x000000001dcd6500, RDI: 0xffffff800d168778
R8: 0x0000000000000001, R9: 0xffffff805e5f3e88, R10: 0x0000000000000011, R11: 0x0000000000000000
R12: 0x0000000000000000, R13: 0xffffff800d168770, R14: 0xffffff800d168778, R15: 0x0000000000000000
RFL: 0x0000000000010082, RIP: 0xffffff800020c590, CS: 0x0000000000000008, SS: 0x0000000000000010
Error code: 0x0000000000000000
Backtrace (CPU 0), Frame : Return Address
0xffffff805e5f3a00 : 0xffffff8000204d15
0xffffff805e5f3b00 : 0xffffff80002d1208
0xffffff805e5f3c50 :
Model: MacBookPro8,1, BootROM MBP81.0047.B27, 2 processors, Intel Core i5, 2.3 GHz, 4 GB, SMC 1.68f99
Graphics: Intel HD Graphics 3000, Intel HD Graphics 3000, Built-In, 384 MB
Memory Module: global_name
AirPort: spairport_wireless_card_type_airport_extreme (0x14E4, 0xD6), Broadcom BCM43xx 1.0 5.100.198.104.5)
Bluetooth: Version 2.4.5f3, 2 service, 12 devices, 1 incoming serial ports
Serial ATA Device: Hitachi HTS545032B9A302, 298.09 GB
Serial ATA Device: OPTIARC DVD RW AD-5970H
USB Device: FaceTime HD Camera (Built-in), 0x05ac (Apple Inc.), 0x8509, 0xfa200000 / 3
USB Device: Hub, 0x0424 (SMSC), 0x2513, 0xfa100000 / 2
USB Device: BRCM2070 Hub, 0x0a5c (Broadcom Corp.), 0x4500, 0xfa110000 / 5
USB Device: Bluetooth USB Host Controller, 0x05ac (Apple Inc.), 0x821a, 0xfa113000 / 8
USB Device: Apple Internal Keyboard / Trackpad, 0x05ac (Apple Inc.), 0x0245, 0xfa120000 / 4
USB Device: Hub, 0x0424 (SMSC), 0x2513, 0xfd100000 / 2
USB Device: IR Receiver, 0x05ac (Apple Inc.), 0x8242, 0xfd110000 / 3Hmm. The problem still may be the RAM - Apple buys the RAM it puts in its machines from third-party vendors (usually Hynix) so it could be a RAM problem.
There are a couple of things that you can do yourself before taking your machine into an Apple Store or an AASP... download and run an application named Rember that will run a RAM test for you - let it run for a couple of hours or even overnight. If it turns out that your RAM is faulty, Rember will let you know. If it is faulty, then you have a couple of options - replace the RAM yourself or (particularly if you're under warranty still) take the machine to an Apple Store or AASP and have them replace the RAM.
If Rember finds no fault with the RAM, then you'll need to take it into an Apple Store/AASP and get a free diagnosis on the machine. Three beeps do usually indicate faulty RAM, but if it tests good with Rember you likely have another problem - it could be something as simple as the RAM, somehow, not seated correctly or signs of another hardware problem.
Run Rember first... call back with results.
Good luck,
Clinton -
ipad 2 screen is black . when i press the power button it takes a screen shot but i have no functionality . tried holding the home and power button together but the screen just flicker and stay black . no apple icon shows up. help please
Make sure it is charged for about 10min using the adapter, then connect in recovery mode, explained in this article:
If you can't update or restore your iOS device -
I have a problem with my MacBook Pro, I pressed the power button and after that the apple noise came and the screen turned blue. What can I do and what happened? pls help & thx btw
You may find this helpful:
http://support.apple.com/kb/PH14061
Ciao. -
Whenever I close my laptop then open it it does not turn back on, the screen stays off but I will hear the fan running. I then have to physically press the power button for it to turn on. Help!
Try here. iPhone and iPod touch: Frozen and unresponsive
-
I CAN TURN MY IPOD ON BUT I HAVE TO HOLD THE POWER BUTTON OR IT WILL TURN OFF IT HAS BEEN LIKE THIS FOR ABOUT A WEEK OR TWO AND IT IS REALLY ANOYING. PLEASE HELP ASAP!!!!!!!!!!!!!!!
Try:
- Reset the iOS device. Nothing will be lost
Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Restore from backup. See:
iOS: How to back up
- Restore to factory settings/new iOS device.
If still problem, make an appointment at the Genius Bar of an Apple store since it appears you have a hardware problem.
Apple Retail Store - Genius Bar -
my ipad is on an infinite loop. I used ios7 for a few days and then did updates on some of my apps. that's when the infinite loop started. I have tried pressing the power and home button at the same time, but it doesn't work. Please help!
I even tried some hints posted for ios6 (turn off Ipad, holding home button and plugging in power cord at the same time and then releasing the home button)
I did manage to get a different screen that shows the itunes icon and a power cord, but nothing happens.You were on the right track. You got the connect to iTunes screen and you ended to use iTujes to restore your iPad. Try recovery mode again.
Recovery Mode Instructions
Disconnect the USB cable from the iPad, but leave the other end of the cable connected to your computer's USB port.
Turn off iPad: Press and hold the Sleep/Wake button for a few seconds until the red slider appears, then slide the slider. Wait for iPad to turn off.
If you cannot turn off iPad using the slider, press and hold the Sleep/Wake and Home buttons at the same time. When the iPad turns off, release the Sleep/Wake and Home buttons.
While pressing and holding the Home button, reconnect the USB cable to iPad. When you reconnect the USB cable, iPad should power on.
Continue holding the Home button until you see the "Connect to iTunes" screen. When this screen appears you can release the Home button.
If necessary, open iTunes. You should see the recovery mode alert that iTunes has detected an iPad in recovery mode.
Use iTunes to restore iPad. -
I recently bought mbp retina haswell 13. When i use it today suddenly my display went black....i dnt have any idea i try to press the power button then it gave beep sound. Then i press it for few seconds then it shutdown. I try to turn on again same result...plz anyone have solution for this ...help me
See Ogelthorpe's link:
Note: Portable computers that have a battery you should not remove on your own include MacBook Pro (Early 2009) and later, all models of MacBook Air, and MacBook (Late 2009).
Shut down the computer.
Plug in the MagSafe power adapter to a power source, connecting it to the Mac if its not already connected.
On the built-in keyboard, press the (left side) Shift-Control-Option keys and the power button at the same time.
Release all the keys and the power button at the same time.
Press the power button to turn on the computer.
Note: The LED on the MagSafe power adapter may change states or temporarily turn off when you reset the SMC. -
Hi I have an Imac I5 21.5 inch.It was working perfectly.Then i didnt use that for about 2 months. Week ago when i want to start the Imac ,it didnt start.
When press and hold or keep on pressing the power button then i hear the fans are working and i get a continuous beep( but low freqency tone).
But screen does not turn on.Please help me to rectify this problem.Best Regards. By the way I am an electronic technician.So if there are any technical things to be done, Pls let me know.I can do it my self.Hey terremo,
Thanks for the question. From the information you provided, it sounds like the iMac is successfully turning on, however video is not displayed. These symptoms can usually be isolated further by the troubleshooting steps in this article:
Apple computers: Troubleshooting issues with video on internal or external displays
http://support.apple.com/kb/HT1573
Thanks,
Matt M.
Maybe you are looking for
-
Can I use more than one transition when creating a slideshow in IDVD
I want to use more than one transition in IDVD when creating a slideshow, is this possible?
-
How can I input Chinese in the Playbook?
How can I input Chinese in the Playbook? such as in browers and contact
-
FPX & Motion not integrated properly - what to do?
I've just installed Motion 5 and I'm trying to use it with FCPX. I want to export a clip from FCPX to Motion. I'm following these instructions: To send clips or sequences from Final Cut Pro to a new Motion project In Final Cut Pro, do one of the fo
-
Hi All, I try to call a program in AS400. Is this possible with PI. I made a research and found that through JDBC (with jt400) we can connect. BUT can we call a program which is written in RPG or COBOL? Is this possible? Thanks.
-
Docbook.xsl processing error on XSQL XML output
Hi all, I've got an XSQL page query which returns a docbook-schema-valid document in XML. I've written a simple xsl stylesheet to test the output and the results are as expected. I now want to use the docbook.xsl designed by Norman Walsh but I'm gett