Help I cannot oc my system over than 4.45ghz

Hi
I cannot oc my system over than 4.45ghz
I cannot Find reason
after the frequency The system will hang.
I checked voltage,temperature,power
even I updated bios to last version
my system is:
mb:msi z68a-g45(g3)
ram:4gb 1333mhz
power:green 785
cpu:intel i5 2500k
help me

Increase the CPU V. Do not exceed 1.400v's. The mainboard isn't known for it's OC ability, 4.45 is actually a good all around setting.

Similar Messages

Help: Windows cannot restore a system image to a computer with different firmware

I want to recover a complete image of a Windows 7 operating system I have backed up to my other server. But I am getting the error "Windows cannot restore a system image to a computer with different firmware. The System Image was created by a computer using BIOS and this computer is using EFI"
The image was definitely taken from this machine - the firmware has not changed!
What do I need to do to restore the image?
Background Story ..
I bought a new HP 255 laptop per-installed with Windows 7 without Operating Systems instal disks (I will NEVER be stupid enough to do that again!).
I took a complete image of the systems, as suggested so that I was well backed up.
However, my machine corrupted its operating systems with a few weeks. The boot recovery CD did not work (would not boot). So in desperation, and because time was short I went out and bought another, legitimate copy of Windows 7 DVD with a license key (So now I have 2, legitimate copies of the operating system!).
I installed the new copy of Windows 7 - but it was dreadful, because many drivers were missing. Mostly the missing drivers were not available on the HP support site for this machine. ALso, boot up was increadibly slow compared to the original OS installation.
So I created a new boot recovery disk from the new version of Windows, and tried to restore using that. New boot disk loads ok, I can find the old image on my network (after loading a few network drivers). But I won't instal the image - giving the above error message.
I tried deleting the EFI partition from the disk (using GPARTED to reformat that partition). That killed the Windows 7 on the machine - but still gives the same error message when I try to re-image the machine.
I have tried going into the BIOS settings .. HP 255 has a "Legacy Mode" - which I have enabled, but this makes no difference at all!
I think that the kind of solutions I am looking for might be:
1. There is a clever way of disabling EFI on my 255 so that it looks like a legacy BIOS machine, or
2. This EFI this is wired into my new boot recovery disk - and there is a way of creating a boot recovery disk that does not use EFI
This has taken me about 2 weeks so far,please help with any suggestions!

DonOxley wrote:
Erico,
I suspect that "MSDOS" is what the Gparted tool calls "MBR" for a partition table, as explained here:
http://superuser.com/questions/700770/mbr-equals-msdos-for-gparted
I think that you are suggesting I give up on trying to recover the image I have stored on my server and just to instal Windows 7 from my new copy. There are two problems with this.
1. After having systematically downloaded all of the drivers from the HP 255 notebook support page, I am still seeing missing drivers listed. Install the AMD graphics softpaq driver first. It also contains the chipset drivers.
2. The machine is taking a hugely long time to boot up, and seems much slower with this version. Maybe that is a product of using "EFI" rather than "bios" - I don't know.
My assumption is that HP had some special set-up option with their version of Windows which makes the machine more performant. It does not seem to be a coincidence that the image they deliver the machine with is not quite compatible with a 'normal' Windows 7 instal.
So my original question stands: How do I recover the image that I saved away (as per instructed) when I first bough the machine?
You still have not said what you used to create the system image. What is the "image" file's extension?
You are mistaken in your comparison. MSDOS is an operating sytem MBR is a partitioning scheme. that is comparing apples to oranges.
The article is making an oblique reference in that using GPARTED is more or less equated to using the diskpart utility at the command line. Everything done at the comand line is essentially done by use of MSDOS commands. GPARTED does the same thing with LINUX commands via a graphical interface so you don't have to type in the commands in a Linux console.
Do you mean making a backup? a backup is not a clone which can be reproduced on different hardware. The SSD disk replacement does make the hardware differ from the original configuration.
Follow the instaructions on the following tutorial to make your disk a GPT type before installing.
http://www.disk-partition.com/articles/mbr-partition-table-to-gpt.html
****Please click on Accept As Solution if a suggestion solves your problem. It helps others facing the same problem to find a solution easily****
2015 Microsoft MVP - Windows Experience Consumer

I cannot install ODX Yosemite over OSX Mavericks as my Mac Book Pro (early 2011) advises that the disc "Mackintosh HD" is used for Time Machine back ups. This is not the case however as I use a separate external HD for this purpose, help please ?! T

I cannot install ODX Yosemite over OSX Mavericks as my Mac Book Pro (early 2011) advises that the disc "Mackintosh HD" is used for Time Machine back ups. This is not the case however as I use a separate external HD for this purpose, help please ?!
Thanks

Check this link out...
OS X: Cannot install on a volume used by Time Machine for backups
I was apart of this thread and it helped the OP...
Re: System installer thinks my main drive is my time Machine backup and won't install.
KOT

Error Message= x Cannot find the HTML help browser installed on your system.

Help! I cannot seem to find the solution for the error message I get when trying to generate a layout in Microsoft HTMl Help (Primary Layout). I am using the trial version, but it didn't seem to be an issue for anyone else in my class that was also using the trial version.
The error message states, "Cannot find the HTML help browser installed on your system."
Thank you!

Sounds like a problem with the installation of RoboHelp on those machines. When you install RoboHelp, it installs the necessary files to view a CHM.
See www.grainge.org for RoboHelp and Authoring tips
@petergrainge

I just bought an AirPort Extreme system over this weekend and I am having problem with setting it up. I plugged the cable as explained in the manual but there is no way I can get a steady green light. I all see is flashing amber light. Can anyone help me,

I just bought an AirPort Extreme system over this weekend and I am having problem with setting it up. I plugged the cable as explained in the manual but there is no way I can get a steady green light. I all see is flashing amber light. Can anyone help me,

Think you need to provide some more details about what you are connecting

HT5271 My videos arent playing on my safari and it says "blocked plug in". I go to download an updated version of flash but it doesnt help, and It keeps saying it over and over. I also cannot log in to previous webpages. Cookies are enables and so are

My videos arent playing on my safari and it says "blocked plug in". I go to download an updated version of flash but it doesnt help, and It keeps saying it over and over. I also cannot log in to previous webpages. Cookies are enables and so are pop ups

Uninstall the old Flash plugin versions > Troubleshoot Flash Player | Mac OS
And turn OFF Extensions in Sarfari > Prerferences > Extensions. Quit and relaunch Safari to test.
And check to see if Safari is running in 32 bit mode. Right or control click the Safari icon in your Applications folder then click Get Info. If the box next to: Open in 32 bit mode is selected, deselect, quit then relaunch Safari.

Cannot see BI system in search

Hi experts,
I have configured BI backend system from CE portal and the connection test is successful. However, after I configured, I logged into VC and cannot find BI system I configured in "Search" drop-down list. I can only see Web service destination and RFC destination. What shall I do to solve it? Did I lose any step? I followed the configuration guide from here "http://help.sap.com/saphelp_nwce10/helpdata/en/7e/6dbcea3700452195e3bddaa47c5906/frameset.htm".
Best Regards
Tom

Hi Tom,
I have never made a connection to BI or any SAP System but a JDBC connection from the portal and did all the necessary steps, even though the test connection did not succeed, I could still see the system in VC.
In your steps, I do miss step 6 of the documentation, did you do this as well, may this is something which is required?
6.      Maintain the properties in the following categories:
○       BI/Business Intelligence
■       BI Directory Provider: yes
■       BI Master System: yes
One of the connected BI systems has to be the BI master system. If you are only connecting one BI system, choose Yes. If you are connecting more than one BI system, choose Yes for one system and No for the remaining system.
○       Connector
■       Group: Logon group of back-end system
■       Message Server: Message server of back-end system
■       Remote Host Type: 3
■       SAP Client: Client of back-end system
■       SAP System ID (SID): System ID of back-end system
■       System Type: SAP_BW
You can find the values for the logon group, system ID, and message server from the properties in the SAPGUI logon for the BI back-end system.
Best regards,
Dharmi

Photos cannot find the system photo library

I’m in trouble. I was deleting photos in ‘pictures’ as I wanted to clean up some space on my iMac. My assumption was that ‘pictures' is completely separate to iPhoto (or photos as it is now called). I then go back into photos (the old iPhoto) and get the message 'photos cannot find the system photo library’.
I cannot access any photos at all. I’m working on a large project this weekend and I have purchased hundreds of photos over the last 6 months which I require for the project. Blood pressure boiling at the moment!
Any help please

davidpotterdp wrote:
You absolute genius. When I pressed alt and photos it gave me the option to open the ‘old version’ of iPhoto!!
Just so I don’t mess up again. How do I now get the old iPhotos back into photo?
I did try to look on my time capsule but when I viewed the last back up from this morning, there was no photo in the sidebar to even open?
I’m new to the forum. I did call Apple but probably not wise for me to articulate on this forum what they said!
The iPhoto migration to Photos would have been automatic when you upgraded - there is presumably a way to kickstart that again though I'm not certain how as I've not done so.
If you have a Time Capsule that's great.
I'll see if I can get some others to chip in.
Also, if you can still open iPhoto you can of course continue to use that for the time being.

Help I cannot update or restore my iphone3gs?

Help I cannot update or restore my iphone3gs?
When I try to update or restore my iphone3gs it say the required resource cannot be found. YES IPHONE3GS IS COMPATIBLE WITH IOS5. I went on the apple website and it came up with this:
The required resource cannot be found: This alert message occurs when your device has a newer version of iOS than what is available in iTunes. When troubleshooting a device that presents this alert message, go toSettings > General > About and check the version of iOS on the device. If it is newer than the latest released iOS version, the device may have a prerelease developer version of iOS installed. Installing an older version of iOS over a newer version is not supported.
I have never updated it before or done the pre-release thing. I dont understand how to fix it my iphone version is 4.3.3 (8J2) and modem firmware is 05.16.02.
plz help and thanks for your time

Read the article from which the question was posted, it addresses errors and their resolutions.

Please help, I cannot start-up my PowerBook G4 (grey screen, no options)

Sir/Madam,
My PowerBook (PB) started misbehaving two weeks ago. It seemed difficult for i to access its drive (repetitive whirring sounds). I made a clone while I could and tried to fix any problems using Disk Utility.
At first, minor problems were detected so I booted using the clone (on firewire) and tried to repair. Disk Utility reported the drive was fine. I tried Drive Genius, Disk Warrior and Techtool. I rebuilt the directories, and yet when using the drive, the access problems and delays continued. During this whole process, I kept finding that in System Preferences - Startup Disk list, my firewire clone was not detected. I had to boot with the OPT key pressed to use it (this was unusual).
Anyway after hours of trying to find the fault, I decided to boot from the firewire clone again and completely erase the built in PB drive. After this, I thought, I will do a clean reinstall.
When the time came to do a reinstall, I found that my PB got stuck on the grey screen. Even if I pressed OPT-C on startup (to reinstall the system from optical) nothing would happen. In fact the only thing that does anything different is when I just press OPT on startup. I then get asked my firmware password and there follows what should be a menu of startup options but is actually blank. My firewire clone is absent from the menu, as is any optical disc that I may have placed (eg Leopard installation or the original system discs that came with my PB). The screen with the curly arrow on the left and the straight arrow on the right remains while a little clock mouse pointer shows time passing. After about 45 seconds, the clock hands stop rotationg and the pointer will not longer move. This remains as long as I have waited (hours)
I am now at an impasse where I do not know what to do. I am frustrated. I cannot run any hardware tests, I cannot install any system, I cannot get my PB to see my clone and startup. I would appreciate any help.
Thank you
Message was edited by: Touch

Maybe this will be if interest. Hi everyone. First post...
Anyway, I was updating my 1.5 G4 Powerbook to 10.5.7 and scored the interminable grey screen. No joy from Option, C, Safe Boot, Verbose Mode etc, etc. Ran fsck in Single User Mode and got the all clear from the hard drive. So...
Off to the Genius Bar in Sydney's new Apple store. Again, all clear on the hard drive, so must be an operating system error.
Back home, transferred everything I could think of via Target Disk mode and Firewire to the other Mac and re-installed Panther - yep, it's an oldie but a goodie. Then updated. Then upgraded to Tiger. Then updated. Then tried to load Leopard again. No joy. Grey screen, blue screen, spinning beachball, and clicks and whirrs from the DVD drive.
After about a day of wracking my brains - I may be slow - I checked the About This Mac feature and it hit me. The RAM was 256MB, not the standard 512. Which is a prerequisite for Leopard. And the Diagnostics line said Memory Failure...
Then I found the faulty RAM slot thread/lawsuit/recall notices... None of which applied to my serial number.
To cut a long story shorter, either the RAM module or the slot is stuffed. I need to do a bit more diagnosis, but I can see an expensive swap to a MacBook Pro coming up...
If you're having trouble booting your G4 Powerbook, check it for memory failure. Apparently it's not uncommon. And apologies if this has all be covered before. Hope it helps.

HT1151 I keep getting an error message when installing new software that says "System extension cannot be used /system/library/extension/IoFireWireWDHID.kext was installed improperly" I have no idea what this means and all of my software seems to install

I keep getting an error message when installing new software that says "System extension cannot be used /system/library/extension/IoFireWireWDHID.kext was installed improperly" I have no idea what this means and all of my software seems to install okay

Hello Valerie Anderson,
I'm Harry from Norton Support team. Please check the information provided in a similar thread here:
https://discussions.apple.com/message/21854775#21854775
Let me know if this helps.
Thanks!
Harry

Cannot remember my system admin name

I cannot remember my system administrators name, I know my password, please help it is driving me round the bend

Go to System Preferences>Accounts then there should be a list of the names of all the accounts on the computer on the sidebar.

The height of mx:RichTextEditor in VDividedBox cannot be reduced to less than 200.

I'm using <mx:VDividedBox >, in which there are a mx:RichTextEditor and mx:Image, as in the code below.
When I dragged the divider of the VDividedBox to resize the heights of the Image and RichTextEditor, I found that the height of the
RichTextEditor cannot be reduced to less than 200. Is this a bug?
I replaced RichTextEditor with TextArea, then divider of VDividedBox works fine. I use Flash Builder 4.5. Please try the following code, and
post you result here. Let's help Adobe to make Flex better.
<?xml version="1.0" encoding="utf-8"?>
<s:Application xmlns:fx="http://ns.adobe.com/mxml/2009"
      xmlns:s="library://ns.adobe.com/flex/spark"
      xmlns:mx="library://ns.adobe.com/flex/mx" minWidth="955" minHeight="600">
<fx:Script><![CDATA[
import mx.controls.Alert;
[Bindable] public var imageSrc:String = "http://cseligman.com/text/sky/perigeeapogee.jpg";
private function showHeight():void {
   Alert.show(this.rte.height.toString());
]]></fx:Script>
<mx:VDividedBox width="100%" height="100%" >
   <mx:Image id="image_edit" source="{this.imageSrc}" scaleContent="true"
       horizontalAlign="center" verticalAlign="bottom" width="100%" height="100%"
       />
   <mx:RichTextEditor id="rte"
       width="100%"
       text="The Moon.... Click me to show my height." click="showHeight()"/>
</mx:VDividedBox>
</s:Application>

try setting minHeight of the RTE to 0

Scm:Logical system Name is changed. cannot access BW system.

Hi,
plz help me to solve thi problem.
SCM : Logical system Name is changed. cannot access BW system. system throw an error "Logical System has changed".

Hi Raj,
We can create the Logical system name in SALE or BD54 and we can assign the same logical system name in SCC4 for that particular Client.
If you want to change the logical system name after a client copy or System copy. Use BDLS.
Thanks,
Pundari

Help in using listagg function for more than 8000 char.

Hi Friends,
Need you urgent help in using listagg function for more than 8000 char.
I did the below sample SQL and in "e_orig" and "d_orig" for upto 4000 char it is working fine but I have to use it for more than 8000 char. and it is giving error,
I checked the listagg function is having limitation of 4000 char.
I tried but I am unable to achive this. Can someone provide me a sample example to achive this
select d.dname,d.loc,e.hiredate
,listagg(e.ename,',' ) within group (order by e.deptno) over (partition by e.deptno) as e_orig
,listagg(e.ename, ',') within group (order by e.sal) over (partition by e.deptno) as d_orig
from emp e, dept d
where e.deptno=d.deptno;[ This is my first post, I gone through the guideline for posting a post , and try to go according to that ( I have not pasted here create table and insert as I have used basic table emp, dept for example), please let me know if still I should give this, I will take care from my next post ]
Thanks in advance

Interesting, I didn't know you could do that, but...
BluShadow wrote:
You could write some PL/SQL code that does it all for you, but that would involve loops and would be slow.Well, objects are written in PL/SQL aren't they? And presumably there'll be implicit looping too? So it's not at all obvious that this method will be faster than doing the joining in PL/SQL in memory. The only way to find out is to benchmark them - so I have done that.
I noticed that OP's ref cursor actually only ever retrieves a single record for a bound department number, so I decided the best thing would be to test using a procedure that passes an output string back. I selected all (109) employees and put spaces in to ensure above 4000 characters. I also noticed that as he is using PL/SQL he probably can use a VARCHAR2 type, but just not ListAgg in the query, so I wrote short procedures as follows:
SimpleAggChr     - bulk collect and array processing, VARCHAR2 output
ClobAggPrc     - the custom aggregation method, CLOB output
SimpleAggClob     - bulk collect and array processing, CLOB output
I then wrote a driving script that calls them in the order above and times each call (I like benchmarking so I have my own timing object to make it easy). I then print the lengths for checking, and my object writes the timings to my output table. Running a few times I got varying results, but generally it looks like there isn't a lot to choose between them for performance.
Here's the procedure code:
CREATE OR REPLACE TYPE char100_list_type AS TABLE OF VARCHAR2(100)
CREATE OR REPLACE PROCEDURE SimpleAggChr (x_out OUT VARCHAR2) IS
l_enames     char100_list_type;
BEGIN
SELECT first_name || '                                        ' || last_name
    BULK COLLECT INTO l_enames
    FROM employees
   ORDER BY salary;
FOR i IN 1..l_enames.COUNT LOOP
    x_out := x_out || l_enames(i) || ',';
END LOOP;
END SimpleAggChr;
CREATE OR REPLACE PROCEDURE SimpleAggClob (x_out OUT CLOB) IS
l_enames     char100_list_type;
BEGIN
SELECT first_name || '                                        ' || last_name
    BULK COLLECT INTO l_enames
    FROM employees
   ORDER BY salary;
FOR i IN 1..l_enames.COUNT LOOP
    x_out := x_out || l_enames(i) || ',';
END LOOP;
END SimpleAggClob;
SHO ERR
PROMPT ClobAggPrc
CREATE OR REPLACE PROCEDURE ClobAggPrc (x_out OUT CLOB) IS
BEGIN
SELECT clobagg(first_name || '                                        ' || last_name || ',')
    INTO x_out
    FROM employees
   ORDER BY salary;
END ClobAggPrc;
SHO ERRand the driving script:
SET SERVEROUTPUT ON
SET TIMING ON
DECLARE
l_enames_c1     CLOB;
l_enames_c2     CLOB;
l_enames_v     VARCHAR2(32767);
l_timer     timer_set_type := timer_set_type ('Aggregation');
BEGIN
Utils.g_id := 'Aggregation';
SimpleAggChr (l_enames_v);
l_timer.Increment_Time ('SimpleAggChr');
ClobAggPrc (l_enames_c1);
l_timer.Increment_Time ('ClobAggPrc');
SimpleAggClob (l_enames_c2);
l_timer.Increment_Time ('SimpleAggClob');
DBMS_Output.Put_Line ('SimpleAggChr returned string of length ' || Length (l_enames_v));
DBMS_Output.Put_Line ('ClobAggPrc returned string of length ' || Length (l_enames_c1));
DBMS_Output.Put_Line ('SimpleAggClob returned string of length ' || Length (l_enames_c2));
l_timer.Write_Times;
END;
SET TIMING OFF
SET LINES 150
SET PAGES 1000
COLUMN id FORMAT A30
COLUMN line_text FORMAT A120
SELECT line_text
FROM output_log
WHERE id = 'Aggregation'
ORDER BY line_ind
/and the results:
SimpleAggChr returned string of length 5779
ClobAggPrc returned string of length 5779
SimpleAggClob returned string of length 5779
PL/SQL procedure successfully completed.
Elapsed: 00:00:27.05
LINE_TEXT
Timer Set: Aggregation, constructed at 03 Nov 2011 16:27:07, written at 16:27:35
================================================================================
[Timer timed: Elapsed (per call): 0.02 (0.000016), CPU (per call): 0.01 (0.000010), calls: 1000, '***' denotes corrected
line below]
Timer              Elapsed          CPU          Calls        Ela/Call        CPU/Call
SimpleAggChr          9.84         0.36              1         9.84400         0.36000
ClobAggPrc            9.37         0.32              1         9.37400         0.32000
SimpleAggClob         8.25         0.22              1         8.25000         0.22000
(Other)               0.00         0.00              1         0.00000         0.00000
Total                27.47         0.90              4         6.86700         0.22500
13 rows selected.

Help I cannot oc my system over than 4.45ghz

Similar Messages

Maybe you are looking for