Help, ibook not booting after installing update 10.4.8 combo

Hi there,
i just updated my ibook 500 dual usb, with 10.4.8 combo and when i restarted the screen was gray with a flashing question mark.
I tried to boot in every mode (with x, with startup manager) and also i checked with disk warrior and disk utility and the hard drive is fine.
Any idea?
Thanks
Marco

Well, if disk utility shows the disk, as well as disk warrior, I would move on to reset the PRAM (http://docs.info.apple.com/article.html?artnum=58042). If that does not work, I would run disk check from disk utility on the install cdrom. If that does not work, I would move on to an archive and install. Please check:
http://docs.info.apple.com/article.html?artnum=58042
Mac OS X (10.4.7)

Similar Messages

Macbook pro won't boot after installing update 10.9.3

macbook pro won't boot after installing update 10.9.3

Please read this whole message before doing anything.
This procedure is a diagnostic test. It’s unlikely to solve your problem. Don’t be disappointed when you find that nothing has changed after you complete it.
The purpose of the test is to determine whether the problem is caused by third-party software that loads automatically at startup or login, by a peripheral device, by a font conflict, or by corruption of the file system or of certain system caches.
Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards, if applicable. Start up in safe mode.
Note: If FileVault is enabled, or if a firmware password is set, or if the startup volume is a Fusion Drive or a software RAID, you can’t do this. Ask for further instructions.
Safe mode is much slower to start up and run than normal, with limited graphics performance, and some things won’t work at all, including sound output and Wi-Fi on certain models. The next normal startup may also be somewhat slow.
The login screen appears even if you usually login automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
Test while in safe mode. Same problem?
After testing, restart as usual (not in safe mode) and verify that you still have the problem. Post the results of the test.

Windows 8.1 Pro not booting after install of Hyper V - ASUS z87 + intel 4670K

Hi,
I am running windows 8.1 pro on a intel 4670K 4th Gen Haswell CPU and ASUS z87 plus motherboard. 16gb of kingston hyperx ddr1600 memory.
I have enabled virtualisation technology in the bios. CPU has SLAT.... or Extended Page Table, as intel likes to refer to it.
When I install HyperV platform and management tools the computer configures and reboots
AFter reboot it brings up the blue window image and spinning circle of dots for a while then reboots. It does the same thing again and then reboots and goings into repair mode and asks me to do a system restore. It then restores to before they HyperV install.
I've tried turning off xHCI mode (i.e USB 3.0) in the bios as this seemed to be a known issue with some gigabyte boards. This did not rectify the issue
Updated to latest asus mainboard bios 1405. Same issue still occurs upon install of hyper V.
Automatic repair does not work and I have to restore from system restore point.
I performed a clean boot after installing the feature and it still couldnt boot to windows.. it just sits at windows logo and then restarts a few times and then launches the startup repair. Once the startup repair begins, the only way I can get into windows
is restoring to a system restore point from before the hyperv feature install.
Please see the following logs which may have further information:
CBS Log
https://skydrive.live.com/redir?resid=1F523A0B8734322C!685&authkey=!AGMjUfosLFpzYNI
Setuperr
https://skydrive.live.com/redir?resid=1F523A0B8734322C!682&authkey=!AKS8Jb1S6W2IAH8
Windows update
https://skydrive.live.com/redir?resid=1F523A0B8734322C!683&authkey=!AJdWKuKj4negBoQ
Windowsupdate(1)
https://skydrive.live.com/redir?resid=1F523A0B8734322C!684&authkey=!APplVjuLpNZW_AY
I logged a job with asus support and their response was:
"Clear CMOS and ensure virtualisation technology is turned on in BIOS. If it still doesn't work, seek assistance from Microsoft"
Previously asked this question but took a while to get back to update with the logs and it was listed as Answered.
This issue is still existing and I'd appreciating any assistance.
Simon

Hi Simon,
Thank you for uploading the Log files.
According to the log files, no actuate clue can be found.
So, I suggest you upload the dump file so that we can help you analyze them.
Automatic Memory Dump Settings on Windows 8:
http://www.thewindowsclub.com/automatic-memory-dump-settings-windows-8
It also applies to windows 8.1.
Note: Microsoft provides third-party contact information to help you find technical support. This contact information may change without notice. Microsoft does not guarantee the accuracy of this third-party contact information.
Note: I highly recommend you use SkyDrive to upload collected files and to post screen shots/pictures. Although you might not be used to it, SkyDrive features a lot of free advanced functionality around file storage capacity, sharing,
privacy, and collaboration:
http://skydrive.com
Regards,
Kelvin hsu
TechNet Community Support

HP Pavilion 15-n268sa will not boot after windows update (windows 8.1)

After a series of windows update (windows 8.1) my HP Pavilion 15-n268sa will not boot up, no fan noises, no lights no nothing.
I have tried a "hard reset" a number of times with no success.
When the battery is present the white LED flashes 3 times when the power button is pressed.
Please please help.

Hello Cuffy,
Welcome to the HP Forums!
I understand you notebook will not boot after a series of Windows updates.
Can you tell me if you are able to access the HP Recovery Manager by repeatedly tapping the F11 key while the notebook turns on? If you can access this, try doing a system restore to before you installed the updates. If not I would suggest you go through this document: Computer Does Not Start and the LEDs Blink or the Computer Beeps.
If it's the Caps Lock light that is blinking this document will tell you exactly what the error is (spoiler: 3 beeps is a memory failure). This could also explain the failed updates. The updates are stored in the RAM before being applied to the operating system.
You can try reseating the RAM, or using only 1 of the RAM cards, as you have 2x4GB cards. If it still doesn't work with 1 card, try the other card to confirm it has failed.
You can replace defective cards via HP Phone Support if covered under warranty or at the HP Part Store if not covered. You can contact HP Technical Support at 1-800-474-6836 in North America. For all other regions click here.
Hopefully this information helps!
Please click the "Kudos, Thumbs Up" at the bottom of this post if you want to say "Thanks" for helping!
Please click "Accept as Solution" if you feel my post solved your issue, it will help others find the solution.
The Great Deku Tree
I work on behalf of HP.

Mac Mini will not boot after Security Update 2008-007

Hello,
A G4 Mac Mini machine I was asked to take a look at will not boot after the owner (succesfully) installed Security Update 2008-007 from Software Update. Booting always hangs at the blue screen after the Apple logo, and booting in verbose mode reveals that WindowServer is crashing repeatedly. Permissions and filesystems have been repaired, PRAM reset, etc. Safe boot also exhibits the same problem, but it is possible to boot to single user mode. Hardware checks out fine with diagnostic utilities.
Any suggestions on how to fix this? Unfortunately, backups are not available (it's not my machine =).

Hi Arkku , and a warm welcome to the forums!
I'd certainly give Sig's advice a try first.
If that should fail...
applesetupdone...
This was Posted by: JoseAranda at September 9, 2006 3:48 AM
"OK, restart your computer, hold down Command-s and type in the following:
/sbin/fsck -fy Enter
/sbin/mount -uaw Enter
rm /var/db/.applesetupdone Enter
# The rm command is the remove command which deletes the file.
# Robert: I'd rename the file via: mv /var/db/.applesetupdone /var/db/.applesetupdone.old
reboot Enter
Once you've done that the computer reboots and it's like the first time you used the machine. Your old accounts are all safe. From there you just change all other account passwords in the account preferences!!
end of posted by: JoseAranda"
Reset OS X Password Without an OS X CD...
http://theappleblog.com/2008/06/22/reset-os-x-password-without-an-os-x-cd/

MacBook Pro will not boot after software update

MacBook Pro will not boot after doing an Apple Software Update (of course they will not help you). MONEY, MONEY, MONEY is the name of the game. They can cause your computer to crash and still charge you!
Does anyone have an answer to why my computer is showing a little gear spinning for hours? I have tried several things with NO luck.
Thanks-

Run through the list of fixes here
Step by Step to fix your Mac

My Laptop B490 not booting after bios update

My laptop not booting after updating bios i used windows 8 OS.
I downloaded Bios from following link.
Bios Download Link
After updating bios, system restarted automaticaly, after that only power led is glowing, screen stays blank.
Help me solve it.
Solved!
Go to Solution.

hi sathish291
Welcome to the Forums.
Can you try the following:
1. Power down the machine, remove the AC adapter and battery.
2. Hold the power button for 30secs and reconnect the AC adapter only then turn the computer ON.
If the machine still doesn't power up normally and boot into WIndows then it's likely that something went wrong (could be a bad BIOS flash or an internal component might have gone defective during or after the BIOS update). In this case, you may need to contact lenovo on how to go about getting the unit serviced.
Support phone list
Regards
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follow @LenovoForums on Twitter!

Power Book G 4 wil not boot after oz update Snow leapard os

Power book G4 did not boot after Lastesat Mozilla update, Runing snow leapard, message updatenis not compatable with computer tried to delete update, and will not boot from then on?

You can't run Snow Leopard on a PowerBook G4.
Please straighten your story out.

Brand New 27" iMac i5 will not boot after installing software updates

I just purchased my new iMac 2 nights ago. I have been getting it setup with my apps, mobile me account, etc, and luckily just setup time machine and let it do a full backup.
I just ran Software Update for the first time, and now the machine will not boot. It hangs on the grey screen for about 1 minute before the Apple logo comes up. About 30 seconds after the Apple logo comes up, the grey spinning gear shows up, and about 1 minute after that I get the grey screen of death (You must restart your computer).
Any suggestions? A little frustrated here....

If you mean did I receive error messages, No, I didn't. However, the desktop reverted to the default purple night-sky looking thing, my applications and such all disappeared from the dock, and I couldn't open any files or folders (you don't have permission to ...), etc. I tried signing out and back in, rebooting, using a second admin account on the computer, creating a new admin account, etc. I ran Disk Utility, hardware checker, etc. No errors were found, and nothing changed. I could see all my files and folders, but they had a small red circle in the corner, indicating "locked" or "no permission".
I'll find the lines from the console log if that will help. The error showed up immediately and is in the computer's attempt to access the user/library/application support/sync services and same path to user/library/logs/sync services/log. (or something reasonably close to this. If you can use the exact path, I will get it) The link between my settings and files, and a password is apparently corrupted or something, so that the computer won't even let me change the desktop or any file, so I can't save, edit or discard anything, and can't drag files to another computer on the home network.
At least I'm still under the 90 day warranty, so I can call tomorrow. At this point, the SMART check says the drive is good, so I assume it's software. The only things new are the three auto Apple software updates I installed yesterday, so I immediately suspect them. But who knows?
Does this help you at all?

Windows NT does not boot after installing NI-CAN 1.6.0 or security update

We are running Windows NT 4.0 SP 6 english with MS IE 5.5.
On one machine we had NI-CAN 1.6.0 installed. After installing the security update from Microsoft over the web the machine did not boot.
On another machine the security update was installed. After installing NI-CAN 1.6.0 the machine booted but hangs during logon. On this machine we installed Windows NT, MS IE 5.5 the security update and NI-CAN from new and the effect was the same.
Does anyone else have similar experience with this problem?
Machines with Windows 2000 and XP work well with NI-CAN 1.6.0.
Waldemar
Using 7.1.1, 8.5.1, 8.6.1, 2009 on XP and RT
Don't forget to give Kudos to good answers and/or questions

Hi,
I haven't found any known issues. I going to try it out here. What's the security update you're installing?. I noticed there's a bunch of them in the Microsoft web site.
What CAN hardware do you have (PCI, PCMCIA, etc)?.
Let me know this details and I'll try to reproduce the problem.
DiegoF.
National Instruments.

Windows 8.1 Pro will not boot after installing iTunes 11.1.5.5

It's a little hard for me to accept that this is true, but the symptoms seem to be pointing the direction of the title of this thread. I have an all-in-one touch-screen Gateway computer that came with windows 7 (yeah, a win7 machine that came with touch, yeesh) and I put windows 8.1 pro 64-bit on it with a clean install (actually windows 8 was the clean install and then I did the free microsoft store upgrade to 8.1). It has 4GB of RAM and has a Pentium Dual Core cpu @ 2.2 Ghz. It was running fine with the previous version of iTunes, but as soon as I updated to iTunes 11.1.5.5 (and there may have been other apple things that updated too (ie quicktime of course), the computer prompted me for a reboot and froze during the reboot process (before it even shut down). Then it had trouble booting into windows. I ran startup repair to no avail and decided to do a sytem restore. My most recent restore point was from a few weeks back, before iTunes was even installed at all on the machine. I went back to that point and the machine worked fine again. Then I installed iTunes 11.1.5.5 and the same exact problem occurred - it froze while shutting down after the iTunes install and then would not boot into windows 8. I did another system restore and have not put iTunes back on. The system is working fine. I'm going to try to find out if there's a way to download older versions of iTunes, so that I can install it, but the bigger issue here is: Is this a legitimate bug/incompatibility with some hardware or software or driver that I have on this computer? I run a computer support business so I know my way around but I don't have time to troubleshoot this from scratch. Anyone else seeing this? Apple employees...a little help here? Any input?

let it sit for about 30 min and still got nothing
I then did a "hard shutdown(just pressed power button till it turned off the computer)"
That may not have been long enough. But a "hard shutdown" would definitely have been construed as a problem due to the update.
Asus apparently is a known problem case...
http://blogs.msdn.com/b/usbcoreblog/archive/2013/10/19/help-after-installing-windows-8-1-the-superspeed-ports-of-my-asus-system-don-t-work.aspx
Link courtesy Darrell Gorter [MSFT] found here
"Windows 8 Keyboard and mouse not working"
http://social.technet.microsoft.com/Forums/en-US/w8itprohardware/thread/06e9b341-0619-4085-acbf-e2f0133ca428?outputAs=rss
(RSS given to avoid overhead of opening long thread for IE users)
Note that there may be useful tips for you in both of those threads' comments.
Robert Aldwinckle

Satellite Pro L300 will not boot after Bios update

Help please.
I have just formated a Satellite Pro L300 laptop.
I used all the updated drivers from Toshiba and all went very well.
I then updated the bios with the latest version.
After doing this the laptop will not boot but just keeps scrolling through the start menu and no matter what option I choose it just keeps doing the same thing.
Any ides welcome

Hi
I used the Microsoft installation disk but just keep getting to the same stage until the blue screen appears. I have tried different installation disks and also changed the hard drives as well. I can do everything in bios, change boot device enable or disable devices but that is it. I have tried a few times to instal windows but it just stops at the same point saying windows is stopping instal to protect the system. I fear the bios update has done some permanent damage as I cant get past the dreaded blue screen.Thanks anyway

Can't boot after installing updates

I am quite new apple and this is my first problem I have encountered.
I downloaded updates and now my computer wont boot. I have tried safeboot and it just freezes on the 'starting OSX bar'. I have inserted 'install disk 1' (which is OSX 10.4.6) and gone through disk utilities to repair permissions and the disk - then starting from the hard drive in safeboot and it still gets no further than the 'starting OSX bar'.
If I chosse to boot from the install disk will it take me to the 'erase and intall' option.
What should I do? If anyone can help I would be very grateful.
Thankyou

I guess you could skip the steps you have done already...
Could be many things, we should start with this...
"Try Disk Utility
1. Insert the Mac OS X Install disc that came with your computer, then restart the computer while holding the C key.
2. When your computer finishes starting up from the disc, choose Disk Utility from the Installer menu. (In Mac OS X 10.4 or later, you must select your language first.)
*Important: Do not click Continue in the first screen of the Installer. If you do, you must restart from the disc again to access Disk Utility.*
3. Click the First Aid tab.
4. Click the disclosure triangle to the left of the hard drive icon to display the names of your hard disk volumes and partitions.
5. Select your Mac OS X volume.
6. Click Repair. Disk Utility checks and repairs the disk."
http://docs.info.apple.com/article.html?artnum=106214
Then Safe Boot from the HD, (holding Shift key down at bootup), run Disk Utility in Applications>Utilities, then highlight your drive, click on Repair Permissions, reboot when it completes.
The usual reason why updates fail or mess things up, is if Permissions are not fixed before & after every update, with a reboot... you may get a partial update when the installer finds it doesn't have Permissions to change one obscure little part of the OS, leaving you with a mix of OS versions.
Some people get away without Repairing Permissions for years, some for only days.
If Permissions are wrong before applying an update, you could get mixed OS versions, if Directory is the slightest messed up, who knows!
If many Permission are repaired, or any Directory errors are found, you may need to re-apply some the latest/biggest updates.
May even need to do an Archive and Install if you have room on the HD...
http://docs.info.apple.com/article.html?artnum=107120

InDesign CS3 will not open after installing updates

Hello,
I am having a problem printing borderless with InDesign CS3. When my paper size is set on borderless my photos print very light. If Iremove the borderless setting the photos print fine.
In a effort to correct this problem I downloaded and installed updates for InDesign CS3 now InDesign will not open.

5.0.3 should not have installed after 5.0.4 (that's a problem with the installer), and it may have added problems. First things to try, though, before we get down to uninstalling and reinstalling again, are trashing the prefs (Replace Your Preferences), trying a new user account, and starting with extensions disabled (hold down the Shift key when you boot).
If it comes to reinstalling again, you should probably also run the cleaner tool (CS Cleaner Tool for installation problems | CCM, CS6, CS5.5, CS5, CS4, CS3) before reinstalling, and make sure you have the correct update which you can download again from http://www.adobe.com/support/downloads/detail.jsp?ftpID=4029

HP Advisor, for m9040n HP Pavilion vista home premium not working after installing update.

I have a m9040n hp pavilion desktop with vista home premium. My hp advisor will not work. When I go to the menue to pull it up the icon has changed and is an icon of white pages. When I select the icon Hp Advisor it gives me a gray dialog box called the file type assistant. For searching for software to open the file. I've tried to install the sp 43112.exe update recommended for my hp pavilion m9040n with vista home premium but my hp advisor is still not working. Any ideas as to why my installing the update failed? Is there anything I should do beforeinstalling the update?

Rkmccoy25,
I understand you’re stating the HP advisor isn’t working correctly after an update.
Try doing a system restore back a day or two before the update occurred, if you haven’t attempt that already. Below are the instructions on how to do a restore if you’re unsure.
How to do a system restore
Please respond at your earliest convenience.
Thanks
Clicking the White Kudos star on the left is a way to say Thanks!
Clicking the 'Accept as Solution' button is a way to let others know which steps helped solve the problem!

Help, ibook not booting after installing update 10.4.8 combo

Similar Messages

Maybe you are looking for