Help me with a WRT54GS Router

If you can help me any amount I will be grateful I have 3 Laptops in my house and when one of them is online (like playing online games and stuff like that) when the second gets on the router drops the first laptop for a couple minutes then it reconnects the first laptop so they are both online. Then the third gets on and the router drops the first and second laptop for a couple minutes then reconnects to both of them. So they are all three connected. I want to know if there is a way to make it so that the router wont disconnect any of the laptops when another accesses it.
Message Edited by PaintballFreak on 07-15-2007 08:41 PM

Hi… logon to router’s setup page, try changing wireless channel to 1 or 11, go to advanced wireless settings reduce beacon interval to 50, fragmentation and RTS threshold to 2304, change Transmission rate to 54 MBps…click on "application & gamings" >> QoS >> enable the WMM feature...also try upgrading latest firmware on router, check whether it makes any difference or not and let me know.

Similar Messages

Ip helper address with Policy Base Routing

Does ip helper work with Policy Base Routing? and if so how and what version of the router software do you need?
thanks

As first function at the ingress interface is ip_helper, as second function at the same ingress interface is policy-based-routing.
We have the same situation regarding ip nat in combination with policy-based-routing.

Can I use the WVC54GCA Camera with my WRT54G router?

I have the WRT54G Router - 2.4GHz. Can I hook up a couple of WVC54GCA cam's to my network?My router was not listed in the "routers this cam works well with" section.
Thanks.

It should work fine.

Need basic Help - SG300 with vlan and routing

Hi,
i need some basic help with configuring vlan/routing.
Situation:
DSL Router - Cisco 300 - XenServer
192.168.1.253 - 192.168.1.19 - 192.168.1.10 (mgmt ip)
goal is, to reach from inside xenserver vms the internet.
vms = 192.168.2.x
gateway ip = 192.168.2.1
what i did:
- configured vlan 102, tagged, with the xenserver port
- configured on xenserver a network with vlan id 102, attached to the vm
- this network is conntected to an external bond
- configured ipva4 interface: vlan102 - Static - IP 192.168.2.1 (this is the gateway ip of the vms)
- automatic configured IPv4 Route: 192.168.2.0/24 next hop 0.0.0.0, Directly connected
So at the moment i cant ping from inside a vm to the DSL Router (192.168.2.2 to 192.168.1.253)
any ideas what i misconfigured or whats wrong?
cheers,
-Marco

Hi Tom,
ok, that make sense. I can ping the router now inside vms from 192.168.2.x network.
But i cant ping external adresses, error: Destination net unreachable.
My other problem i have, i cant reach any server from outside over router portforwarding.
How do i have to configure the upload port to the dsl router? Is it a access port or a trunk
port with all vlans (tagged or untagged?) At the moment ive a tagged Trunkport with all vlans.
IPv4 Interface Table
Interface
IP Address Type
IP Address
Mask
Status
VLAN 1
Static
192.168.1.19
255.255.255.0
Valid
Should the VLAN1 ip adress not the router ip adress ? Do i need an additional vlan for
the router ? At the end i like to change the switch ip from dhcp to static (change automaticly
when switching to layer 3 mode), but ive to look for the ios commands first.
What else do i missing ?
Thanks a lot,
Marcus

Is there someone in the St. Louis area I can get to help me with a new router

I have to install a new router for my Apple 10.7.4. Is there someone in the St Louis MO area I can get to help me with this?

Hi Robert, perhaps we can help you here, what is the question(s)?

Can anyone help me with my wrt54gs wireless router?

We have the wrt54gs V7 wireless router hooked up to an older HP desktop computer (running on WindowsXP) and have had a work laptop hooked up to the wireless router for 2 years w/o any problems. We just bought a new laptop running on Windows 7 and although we can see our wireless as an option, have keyed in the Secure Key #, we still cannot connect. I tried running the Linksys set up cd that came w/ the router to set up the wireless connection on the new laptop and it says the disk is not able to run on the operating system. I went thru the process to add a new wireless computer from the desktop/using a USB drive to load the wireless app but when I plug in the USB to the new laptop it stops the set up and says the wireless radio is off on the laptop even though the wireless is on. I am at a loss on how to connect!! 1) how do I get the new laptop to connect to our current wireless router if the set up disk and the USB drive methods do not work? 2) if we eventually get rid of the desktop computer what do I need to do to ensure our wireless connection stays on?
I am ready to throw the new laptop out the window so any help is MUCH appreciated!!

You don't need the setup disk for anything. Connect with a wired computer to 192.168.1.1username blank, password 'admin' (or wahtever you changed it too). Now look up your security and enter it into your new laptop.
Go here for help.

Problem with Linksys WRT54GS router? Please help.

Alright, so I have the WRT54GS, and for the longest time after I bought it, it worked just fine, but I've been experiencing problems lately. We have 2 computers running off the router. One is a wired connection, and mine is wireless, which I'm starting to hate. So whenever I'm playing any kind of game that takes up a lot of bandwidth, such as Call of Duty 4, it's been really laggy, and I get connection interruptions quite often. It disconnects me from all my online programs and, i have to wait about 20 seconds and the connection returns again. It's almost as if the router is just under strain and temporarily gives out? It happens if the other computer is running, or if mine is the only one being used. I really hope this problem is normal and fixable, because I don't have the money for a new router. So I'm wondering, can anyone help me? Please, any suggestions are appreciated. Thanks.

Try the steps below to see if it will help.
There are many reasons for a poor wireless connection, and many ways to solve this issue.
1.      Give your network a unique SSID and do not use Linksys and set your SSID Broadcast to enable.
2.      You can also try A different channel. There are 11 channels and 1, 6 or 11 is better
3.      You can try raising your router approximately 4-6 feet above the floor and make sure the antennas are vertical.
4.      access your wireless software by going to your Profile or preferred networks, if any are named Linksys or ones that you do not know please delete them. Go to the settings or properties and check the information to make sure it is correct.
5.      See if there are any updated drivers to download.
6.      Try to use WPA encryption if you can
*** As always upgrade to the latest firmware
Good Luck,
Ttech

Please help me with my wireless router WRT54G

Hi, I have a wireless linksys router model WRT54G. what i want to do it´s configure a network in my home. I have 2 pc´s, a laptop an a desktop. what I should do to be able to share files,music,videos. between both computers? the laptop has Windows Vista, the desktop has Windows XP Professional. Please Help me. Thank You really Much.

Try this link for file and printer sharing. Also make sure you are running latest firmware on router. You can check it from www.linksys.com/download

I need help with my WRT54GS router.

My WRT54GS linksys router is acting up pretty bad. For example, i am just surfing the web and i have a program Ventrilo going talking to some friends, then all of a sudden i get disconnected from it and my internet just suddenly halts and then reconnects in a mere second or two. it also does this in the middle of me playing my online games. I have done every solution that i thought would remedy this problem, getting an ethernet cable, reinstalling Linksys, restarting my modem and router, changing my internet's security, reinstalling vista on my computer, EVERYTHING. I am not alone in this, my brother, plays the PS3 online, and my other brother plays a computer game on his computer. Anyway, while we are all doing our things on our own computers, we all get disconnected from the internet at the same time and it happens pretty frequently about once every 10-12 mins or so. Is anyone having the same problem, or does anyone have any ideas/solutions to this problem?
Message Edited by Vaun1992 on 02-23-2009 03:02 PM

You need to reset and re-configure your router to see if that makes any difference...Press and hold the reset button for 30 seconds...Release the reset button...Unplug the power cable from your router, wait for 30 seconds and re-connect the power cable...Now re-configure your router...
If you still face the same problem you should try to upgrade your router's firmware...
Download the Firmware from here ,
Follow these steps to upgrade the firmware on the device: -
Open an Internet Explorer browser page.In the address bar type - 192.168.1.1
Leave the username blank & in password use admin in lower case...
Click on the 'Administration' tab- Then click on the 'Firmware Upgrade' sub tab- Here click on 'Browse' and browse the .bin firmware file and click on "Upgrade"...
Wait for few seconds until it shows that "Upgrade is successful" After the firmware upgrade, click on "Reboot" and you will be returned back to the same page OR it will say "Page cannot be displayed".
Press and hold the reset button for 30 seconds...Release the reset button...Unplug the power cable from your router, wait for 30 seconds and re-connect the power cable...Now re-configure your router...
If you still face the same problem you should connect one computer straight to the modem and check if you have stable internet connection or the same problem re-occurs...

Help me with my WRT54GL router plz :(((((

when i connect my router to the adapter the power led still blinking and all the other leds still green unless the DMZ and WLAN leds dont work.i tried make reset but dont work and when connect it to my pc i cant access the main page at 192.168.1.1.plz i want help

i have pc and laptop and connect the pc to the router and the laptop to the wireless.and i never play with the ip adress or such things cuz i dont know and affraid to damage.so i thing its still have the ip 192.168.1.1 and i try connect the modem direct to the pc and worked the internet and ping too.but with my router no .also try put the cable in all the port 1,2,3,4 and still give me the same lose 100% when make the ping.

Extreme as Remote using WDS with Linksys WRT54G router ??

I have seen that the Extreme cannot be used as a remote using WDS with a D-Link wireless router. Is the same true with Linksys wireless routers? I thought I would pose the question before purchasing my 3rd (2 dead, bad luck?) Express or purchasing two Extremes.
I will eventually gravitate towards using an Extreme as my main base station but I do need a remote for wireless printing. I was hoping to put off purchasing an Express until a later date.

Since it doesn't appear that everyone has gotten it to work with this router does that mean special tweeks are required? Is it hit and miss? The wireless router has the latest firmware updates and my network is running with WPA2. Comcast is my provider.

Unable to connect to internet with my WRT54G router

I had no problem until a few days ago. I have it under a secured mode and wanted to unsecure it temporarily. I got into the 192.168.2.1 and clicked the security tab and got a clock that never seemed to come back to i closed the window. I went back into internet explorer and could not get into the internet.  I get a popup in lower right saying Local Area connection. This connection has limited or no connectivty. You might not be able to access the internet or some resources. For more information click this message.
Then I get
Windows could not finis repra the problem because the following actin can not be completed. Renewing your IP address.
I do a setup and get a message
Unable to connect to the router
I try pinging the 192.168.1.1 and it times out.
I do a diagostic and
HTTP Error 12007 connecting to www.microsoft.,com  shows up many times.
I have an Actiontec 701 DSL modem. I can get into the internet using that only.
I've tried resetting the router, I've done   what appears to be a firmware upgrade (lights blink etc), I've tried different power up sequences, I've tried re-booting.
What more can I try?

As of now you are not able to login to your router setup page, and you are getting an error message "Limited or no Connectivity". First you can try is Unplug the Power from your router, wait for 1 min and reconnect the power to your router and check if you connected to the router or still you are getting the same error message.
If still the same problem persist then Press and hold the reset button for 30 seconds...Release the reset button...Unplug the power cable from your router, wait for 30 seconds and re-connect the power cable...Now re-configure your router...

WRT54G Router Install

After using the enclosed CD install program with my WRT54G router I am unable to add another device (a PC) to the network. I get an error message stating that I don't have a wired connection to the router (although I not only have a wired connection to the WRT54G router, the wired connection to the internet (via a DSL modem) did, in fact, work fine.
I'm running Windows XP. The network, pre Linksys router install, was as follows: an ethernet crossover cable between the desktop PC and a XP laptop PC. Printer sharing was enabled on the desktop PC.
The phone support kept cycling me through the sequence run -> cmd -> ipconfig and then asking what IP address was under LAN. But there is no LAN. Unfortunately, the window would show only a Network Bridge with the Default Gateway 192.168.1.1 .
So, how do I get the WRT54G up and running and add the laptop to the network? Is the current network setup with the Windows LAN wizard interfering with the router network install?
(Mod Note: Edited due to non-compliance of forum guidelines.)
Message Edited by OnnagokorO on 11-14-2007 05:11 PM

First of all ...delete the Ethernet or network bridge from network connections .....after that try this link .........

Wrt54gs router to internet cable modem connection drop

With the wrt54gs router set at auto dhcp and mostly on default settings, after some time of inactivity the connection between the router and internet cable modem drops out. That is, when there is no activity (no transmission to/from internet) the connection drops and the wireless connections shows "local only." Any suggestions/comments on why this is so? Thanks!

Have you tried to connect the Modem to the computer and checked if you are facing the same problem or not?
On your Router setup page, change the MTU size from AUTO to Manual and change the Size from 1500 to 1350 and click on Save Settings..... Then click on the Wireless tab and below Set the Radio Band to Standard-20MHz and change the Standard channel to 11-2.462GHz...Wireless SSID broadcast should be Enabled and then click on Save Settings...
Click on the sub tab under Wireless "Advanced Wireless Settings"
Change the Beacon Interval to 75,Change the Fragmentation Threshold to 2304,Change the RTS Threshold to 2304 and Click on Save Settings...
Now see if you can locate your Wireless Network and attempt to connect...

Need help with understanding static vs dhcp on wrt54g router

I currently have a NAS200 device attached to my WRT54G router. The WRT54G is in DHCP mode so as to allow my various laptops and cameras to be accessed over the internet. What happens is that when I have a power failure the NAS200 is given a new ip address even though its plugged into a service port. I am then forced to go into the router and change the port mapping to whatever port the router has given to the NAS. Is there any way to keep the NAS200 at a specific ip address regardless of router resets. Thanks Hexmate

You have to set the static IP address on the NAS. The NAS is currently configured to use DHCP. Change it there to set a specific static IP address. The router itself does not have to option to set a fixed IP address to a specific device via DHCP.
For static IP addresses make sure to choose an IP address which is not used by any other device nor is inside the DHCP server address pool of the router. With default configuration a Linksys router uses 192.168.1.1 and the DHCP server uses 192.168.1.100-149, thus you have addresses 192.168.1.2-99 and 150-254 available.
Use an static IP address like 192.168.1.50, netmask 255.255.255.0, gateway 192.168.1.1 (if the NAS needs internet, e.g. for time synchronization) and DNS 192.168.1.1. That should do it. Again: this has to be done on the NAS device. The router has no option for that.

Help me with a WRT54GS Router

Similar Messages

Maybe you are looking for