HELP - MSI KT6 Delta-LSR

hi,
i have this motherboard: msi kt3 ultra2, and now im buying a new one, for use with my barton 2500+.
i prefer MSI KT6 Delta-LSR, but i dont know if can i change the multiplie like in Abit NF7-S (MaxFID™ Technology).
can i do this on MSI KT6 Delta-LSR ?
remember: in actual motherboard i can change the cpu ratio only to 12.5
i need to select what ratio i want. like 15x, 16x...
thanks and sorry for the english.

a its a via board not an nforce
b why change it if you want multipliers like that ,only reason to change is to run 200 fsb and you only get yto do that with lower multipliers

Similar Messages

MSI KT6 Delta LSR SATA to PATA High CPU Usage Problem

Well recently I've switch to my one of my other motherboards on my network to a MSI KT6 Delta LSR, it was working fine after a reformat, but I notice a few problems and that is 100% cpu usage for SATA to PATA, and vice versa, which seems really crazy. Then my network card performance is ISDN speed sluggish, and I tested my line to be working 100% with another mobo. But when I put another NIC on the same mobo it suffers the same speed problems.
Any suggestions? The rig is specs:
Barton 2500+
Antec QuietPower 350W
200GB Seagate SATA HDD
40GB Seagate PATA HDD
ATI Radeon 7500 AIW
Audigy 2 Value
Realtek 8139 NIC
MSI KT6 Delta LSR Mobo
2x512 MB PC 2700 RAM
Pioneer 107D DVD Writer
LG 16X DVD-ROM
56K Modem (A-open)

Shouldn't say what I don't know about SATA, but since I found below, I need ask if VIA 4in1 drivers are installed, preferably while in SafeMode I say:
http://www.google.se/search?q=cache:X6ewgPiIHYcJ:www.qdi.nl/cgi-bin/bbs/YaBB.pl%3Fboard%3DP4I865%3Baction%3Ddisplay%3Bnum%3D1074174096+sata+to+pata+cpu+usage&hl=sv
I recently installed 160g Seagate barracuda 7200.7 drive on SATA port. (I enabled the Bios using Auto) I have a P4I865pea-6al mother board, with two PATA drives . When copying files between the PATA drives on ide ports, to or from, the SATA drive, I notice the CPU usage goes up to 100%, but when copying files from one ide drive (the PATA drives) to another the CPU usage is very low.
Is there a bios setting that will allow me to copy files from the SATA drive to the Pata drives using a small amount of CPU power, found when just copying between the Primary and Secondary IDE drives? I am using Adobe premiere pro, which uses a lot of CPU power, and the high CPU usage of the SATA drive crashes this program? Any help would be appreciated
Re: CPU usage with SATA drive?
« Reply #1 on: Oct 30th, 2004, 7:17pm » Quote Modify
have you installed the newest chipset- and ide drivers ?

Msi kt6 delta lsr temp problem?

i have just installed a msi kt6 delta lsr , but when i have ran the system a while the sys temp is around 40-42 c and the cpu temp is around 52c .
on my old mobo the temps never went above 35c for the cpu and 25c for the sys temp .
my specs for old mobo etc =
AMD Athlon(tm) XP 2600+
jetway v400db (kt400 chipset)
400w psu
ata133 80gb hd (maxtor)
512 ddr333
geforce fx5800 ultra
windows me (but same in win xp pro)
2 fans blowing air into case and 2 sucking air out
does anybody know a way to improve the temps please

Yippee! A ME user, like me! You know I guess MS support for W98 and ME has been prolonged til 2006? It has partly to do with Linux.
The temperature for the CPU is a little high, but not alarmingly so. Barton gets a little bit hotter on these boards, and I think it is the placing belovw the PSU that is the cause. The system temperature for you is no problem.
To get the warmth away from the CPU I suggest a fan placed in the case door/side, that sucks it out.
Perhaps you have not got such a case door? Then I suggest a quiet 80 mm fan on the back of the case as high as possible, again sucking air out in order to make a nice air flow. Another suggestion is to tie away cabling to the sides of the case as much as possible, power cables, IDE cables etc.

Sata on the MSI-KT6 DELTA LSR

Hello
Can someone tell me if i can run 1 sata disc with windows XP and no ide hdd wil this work on my MSI-KT6 DELTA LSR motherboard.
Or do i need to do it in raid
Greetz sjoerd

It's possible. There's one person who's had problems and there's others that say they can. The FAQ on the ASUS KT600 board says you can on XP (not sure about me or 98), so accroding to them the 8237 bridge should be able to. I'll paste the Asus steps which should be about the same. You need to up date your bios to the one ending in .52 (for MSI). Via has some newer drivers posted Sept 22nd ...maybe go with them at link below and follow the asus steps for 1 HD. Post back if it works. I'd use XP with SP1 incorporated. I'm not saying the answer to your question is a definite "yes".
ASUS FAQ site:
I have only one HDD, but it's SATA HDD. Can I use it to install Windows XP on A7V600 without building RAID?
Yes, you can install Windows XP with one SATA HDD on A7V600.
Please first copy the driver from A7V600 support CD \Drivers\VIARAID\DriverDisk\SATA\*.* into root directory of floppy disk.
(i.e. root directory of floppy disk should contain \pide and \sata folders, txtsetup.oem and vt6420 files.)
Then, boot system by Windows XP installation CD, when the below message show up, press "F6".
"Press F6 if you need to install a third party SCSI or RAID driver"
Then, press "S" to specify additional device when next screen show up. Put the driver floppy disk you made and press enter to continue.
(If the floppy disk is made successfully, the installation program will ask for selecting driver. Please then select "VIA Serial ATA RAID Controller(Windows XP)".)
After SATA driver loaded and Windows XP can recognize SATA HDD, you can continue to install Windows XP as usual.
(If the driver is selected successfully, but the installation program cannot find your hard drive. Please check whether the hard drive is connected correctly both SATA cable and power cable.)
Via has some new Sep 22nd drivers (you might try those) and in the notes it says it does JBOD along with RAID.
http://www.viaarena.com/?PageID=310

MSI KT6 Delta LSR and Radeon 9600 XT 256mb x8 AGP Problem

hi,
Ive just brought a Radeon 9600 XT 256mb and it wont run at x8 agp at all, games lockup as soon as i start them, within 5 mins all text on display corrupts and i get a message saying the gpu recover has set the gpu to default settings.
I cant change anything in BIOS to set it to x4 agp as its not selectable and says AUTO only for agp speed setting.
Only way to alter is goto smartgart in ATI drivers and select x 4 agp if u get in before text corrupts :(
Ive managed to get it stable at x4 agp now through smartgart.
BUT it says on box and in manual this motherboard supports agp x8 but why dont it run it ???
i havent a clue whats up with it.

hi,
Ive got it running stable in x4 agp and found a post on ATI website about some motherboards not working proberly at x8 agp with Radeon 9600 series graphics cards.
http://mirror.ati.com/support/infobase/4219.html
Got nice scores in 3dmark 2001 and 3dmark 2003
But what confuses me is Quake 3 demo that didnt change at all over my old card and radeon 9000 pro i tried once too.
I got
174fps with Radeon 9100
175fps with Radeon 9000 pro
173fps with Radeon 9600 XT 256mb
Thats on Athlon xp 1700
strange or what ?
oh well its a old demo anyway but main thing is big increase in 3dmark 2001 by over 2000 marks

Problems installing windows on 36.7GB raptor on KT6 Delta-LSR

I've been trying to get this damn thing to work for a few days and then someone told me about the forum here at MSI. So far I've been reading different threads now for a total of approx. 3-4 hours and I don't think I've come across someone with my exact problem unless I've overlooked it. I've had two 40GB drives for a couple of years now and I decided that I'll upgrade to a WD 36.7 GB raptor. I thought all would be good until I popped it in and tried to install windows on it. I boot off the Win XP CD and press F6 to instal the SATA drivers. It accepts the drivers on the floppy, recognizes the drive and reformats and continues until, right after the format it says, "The disk or CD may be damaged......blah blah blah." I don't know if this is referring to my HDD, but it seemed like it was referring to my floppy b/c when I press enter to continue, it asks me to insert the floppy again, and then it reads the floppy and gives the same error. I've been trying to get this to work for the past few days now, and I think I tried almost everything. I disconnected all other optical drives and HDD's except for the Raptor and my dvd writer and still same prob. I tried d/l new sata drivers from MSI and still same problem. I changed where I plugged the sata into (since there were two ports) and still same thing. I wanted to update my bios (v5.5) but the readme file said not to flash from a floppy. I don't have another drive to flash from, so I don't know what to do about that. Please anybody help!!! My system spec are below...
MSI KT6 DELTA-LSR
AMD 3000
1.5 GB RAM
ATI Radeon 9200
WD 36.7 RAPTOR
Samsung 40GB 7200rpm
LG CD writer
LG DVD writer
Enermax 300W
SB Audigy
D-Link wireless network adapter
....I think that's about it.
When I tried installing last the CDRW and Samsung drive were disconnected....

Hello,
I would like to comment on the 1.5Gb of ram.
Please use 1 stick and try again.
Also I hope you are not mixing modules of different make/spec/size.
1GB + 512MB
512MB + 512MB + 512MB <this one is good if thry are all the same make/model/revision
256MB + 256MB + 1GB
You can test the memory with this program.
http://www.memtest.org/download/1.51/memtest86+-1.51.floppy.zip
- Extract all the files to a folder, then run the install.bat.
- It will make a memtest bootdisk.
- Then you must boot from this disk, please test each module individually.
- If they are all fine then try your combo and see what happens.
- Test each module for 1hour, if you get any errors instantly then you can stop and change module.
Do not flash until you are sure that the memory is ok.
HOW TO FLASH BIOS
==============
Download this run it to make a boot disk.
http://www.nerdlabs.org/bootdisks/diskimages/wboot98se.exe
Then get a 2nd disk, copy everything in the BIOS zip to it.
Boot from the RAMDRIVE DISK, start computer without cdrom support.
once its all loaded, put in the 2nd disk.
type
copy a:\*.* c:
press enter
type
c:
press enter
type
adsfi709 a6590vms.570
press enter
it should flash the BIOS.
Then you must turn the PC off and clear the CMOS, (JBAT jumper).
Reconfigure all of your settings.
==============

Problem with KT6 Delta-LSR

Hello
I bought MSI KT6 Delta-lsr today and haven't had it work yet.
Usually when I turn on the power only fans start to run and i get memory or processor error from d-bracket leds. Memory chips and processor should be ok since sometimes If I clear cmos and start pc, it seems to start fine and all leds are green but system will hang in winxp loading screen. Changing options in bios doesn't seem to do any good, usually boot after editing bios will cause again memory or processor error.
Any idea what is causing this problem?
Specs.
Amd TB 1ghz -> too old for this mobo?
256mb seitec ddr 333 (also tested Twinmos memory chips)
Msi kt6 delta-lsr
Msi gf4 ti 4200
harddrives, cd, cd-rw, the usual stuff...

Thank you for moving this topic to right forum.
I was wondering if those memory chips just doesn't work with my processor.
Could someone explain me this fsb and ddr speed stuff? Not sure if my tb runs
with fsb 100 or fsb 133. Or does those setting even matter for ddr rams?
Manual says that if I have cpu speed 100 and 333 ddr it's not supported but 133 and 333 should work. Still pc sometimes seem to start up but freezes soon. So to me it seems memory and proccessor works.

DDR400 freezing on KT6 Delta-LSR ?

I usually run 2 x sticks of 512MB Kingston DDR400, and have never had a problem.
I've removed them to test a 1GB stick of Kingston DDR400, but it won't work at 'full speed'.
I'm guessing the RAM is fine, as it was working perfectly in the system I pulled it from.
XP freezes (after about 5-10 mins) when I run the RAM at 400MHz, but seems to be ok at 333MHz.
> Tested RAM in all slots, still freezes
> Booted into Windows Memory Diagnostic - no errors
> Booted into Memtest86 - no errors (didn't let it run long though)
> Ran HCI Memtest from XP, and it froze as soon as the test started. But will run fine at 333MHz.
I ordered another 1GB stick a few days ago (to have 2GB total). Have I wasted my money? Will I have to run my DDR400 RAM at 333Mz?
Any suggestions?
View bigger image: http://i35.tinypic.com/2l8x5kw.gif
MSI KT6 Delta-LSR
Seasonic S12 430W PSU
AMD Athlon XP 2800+
1GB Kingston DDR400 (KVR400X64C3A/1G)
MSI GF6200 graphics card
M-Audio Delta 66 audio card
2xSATA HDD, 2xPATA HDD, 1xCD drive, 1xDVD drive

I tried disabling spread spectrum, froze again.
Bugger it. I'll just stick with 333. I'll be getting another one (DDR400) in the mail in a few days, so I'll test that (by itself) and see if it can run at 400. Not that it will be much use even if it can.
I was going to buy 2 sticks of 333 anyway, but the 400s are cheaper. So I guess even if I'm stuck at 333, I've still saved a few dollars.
Nearly time to retire the Delta-LSR I think....

I have a problem MSI kt6 delta help!!!!!

Hi
I have a problem with my MOBO MSI Kt6 Delta, The problem is i cant use Windows XP with my MOBO.
My hardwares are: AMD XP2600 333mhz, DDR 512MB PC2700,Geforce4 128MB ti4400 (msi), CDRW TDK VeloCD 24x10x40, HD SEGATE 120 GB SATA.
When i installed Windows XP it couldnt start great (error with Video) for that reason i installed the Geforce drivers via Safe Mode. then i reset and work great only for 15 MIN (it shows blue screem error with some problem with video card) and for that reason i installed windows 98 and works great (we hate win98) lol. Pls help me

Try with another video card, if the problem is solutioned, review your video card. In The BIOS activate the Fast Write for AGP. I have a Geforce 4 MX 440 8x 64 MB and works very very fine.

Need help from somebody with the "MSI KT6 Delta-FIS2R" motherboard

Hi everybody!
I really need some help from somebody with the MSI KT6 Delta-FIS2R motherboard (the one with onboard LAN, Audio, RAID, S-ATA and IEEE1394 firewire). You see. I've got this board myself but it's been destroyd. Some values for the onboard devices in my board has been overwritten so that windows no longer recognizes the onboard LAN and Audio controller anymore. I really need some help from somebody with this board.
I need to see what the values for the onboard devices should be. I hope someone can help me by sending me a repport from the Everest home edition: http://www.lavalys.com/products/overview.php?pid=1&lang=en
If anyone could do me this favour, I would be VERRY thankfull

Quote from: HYSTERIAH on 12-November-05, 06:24:20
I really need some help from somebody with the MSI KT6 Delta-FIS2R motherboard
HYSTERIAH,
With 76 Replies and 277 Views on your original thread, it looks to me like people have been trying to help you.
So there is no confusion, I am locking this thread so all your help and advice you receive will be in the same place, so people do not need to jump between threads to keep track of what has already been suggested for this mobo of yours.
Richard

MSI KT6 Delta FISR KT600 Wont Start Up

Hi All I Have a MSI KT6 Delta FISR Motherboard With a AMD Athlon XP 2400+ 2.00GHZ In My Spare Pc and It Was Working Fine Last Week But When i Turned It On I Seen That My hard Drives Were Not Detected In The Bios Under Standard CMOS Settings So I Saved My Bios and Turned Off The Pc To Sort The Drives and When I went To Turn It Back On It Wouldnt Boot Back Up
So I Tried Unplugging The Hard Drives Again and Still No Boot Tried My 1gb Ram From My Main pc and Still No Boot So I Setup The D-Bracket To See If That Could Find My Problem and It Says That My CPU Was Damaged or Not Installed Properly So i Took It Out and Put My AMD Barton 2500+ In and My 480watt Hiper PSU and It Said That CPU Was Damaged or Not Installed Properly So I Tried My 2400+ In My Other Motherboard What Is a MSI K7N2 Delta ILSR nForce 2 Ultra 400 and It Worked Fine Both CPU's Did.
System Specs Of Spare Pc.
AMD Athlon XP 2400+
400watt PSU
512mb ddr 333
ATI Radeon 9600Pro
All Help Will Be Apreciated Cheers.

Hi, I received the same message from the D-bracket, so mine wont boot never, If you get how it works from yours please explain what you did here, in order to get my board alive. Sorry, but I tried everything in the book with this mobo and nothing worked (KT6-LSR non delta version), and I feel that I can't help you out so much.

MSI KT6-Delta FIS2R Broadcom doen't accept any driver

I've problem with MSI KT6-Delta FIS2R networkcard Broadcom doen't accept any driver, anyone help me.

I've got the same problem with the 4401 onboard lan of my Kt6 delta lsr.
I ran the dos-diag tool from the broadcom website and it reported an error
in the 3. test.
It reported an invalid mac-address (ff-ff-ff-ff-ff-ff) as well.
I can't get it to work in linux either.
Either the board is damaged or the bios is buggy (v3.4).
I would really appreciate if someone could tell me how to fix this.
Are there different verisons of the kt6?
I've got version 2.0.

KT6 Delta-LSR lock ups

Hi again , i was having trouble with my KT6 Delta-LSR not reading the correct cpu speed . ie it read 1.1 when it was a barton 3200 , I was advised to turn fsb up to 200 , which i did and it displayed the correct cpu, but i am getting lots of lock ups now, if i put back down to 166 its very stable , but now i cant get pc to boot after last lock up , it just freezes after american megatrends screen .
KT6 Delta-LSR
barton 3200
1gig cas 2 ddr400
maxtor 120 gig sata
creative 5950 (latest drivers)
onboard sound
480w thermaltake psu
winxp pro , fully updated .
any help much appreciated
adam

You don't mention the Brand of your ram. You stated that' it's Cas 2.
I purchased some generic ram that was Cas 2, but I couldn't push my FSB above 100. When I upgraded to some Kingston (see below) I could easily push it to 166.
Good luck!!!

MSI KT6 Delta wont boot

My MSI KT6 Delta system no longer boots any further than the memory test? why? any ideas? any solutions other than replacing the motherboard etc.
some background:
motherboard: MSI KT6 Delta
CPU: AMD Athlon XP 2800
Memory: 1Gb branded
Graphics: Geforce FX 5200 AGP
PSU: Antec TrueBlue 480
Screen displays the memory test then a message relating to BIOS setup i.e. "Del: BIOS Setup" plus a new option i dont remember seeing previously namely "F10: Flash recovery" btw pressing 'del' doesn't help you cant get into the BIOS setup. Having cleared the CMOS via JBAT1 i now just get the MSI Welcome screen. If it helps the D-Bracket displays a red led top left.
its all a bit odd really, everything was fine on Friday night, but come Saturday morning its all gone pear shaped.
any help appreciate

OK. Well, the procesor is where I'd start troubleshooting.
Step one would be to unplug power cable and other cables on the back of the computer, wait a while ( you'll hear a faint zzipp ), and then move JBAT jumper in order to clear CMOS. That will force you into BIOS.
Eh, thought of something. BIOS will stop sometimes if it can't find a keyboard. And you say entering BIOS is impossible. Perhaps you have more than one problem? a) processor's BIOS settings are impossible, b) the keyboard hinders you from entering BIOS. However, the CMOS clearing should in either case be a good start.
Your problem very much reminds of what happened to me and others while playing with CoreCenter. I know you didn't but can't help saying so.

My system crashes when i use my soundblaster on my KT6 delta LSR

(English is not my native language, so sorry for the mistakes)
Hi, i'm new here and i need help, i just bought a KT6 Delta LSR (integrated 5.1 sound) and i want to use my good old soundblaster live! 5.1 but when i disable de integrated sound and plug my sound card the system, in the middle of windows operation (windows always boot), all of a suddden crashes or simply the sound freezes and stay in the same sound over and over again and then the whole system hangs and i have to reboot the system.
I have no idea of what could be causing the problem...
When i use the integrated sound it works fine and in stranges cases (for example: when i'm connected to the internet for more than 30 minutes) the system hangs, but with the sound card would not work 15 minutes ok.
Hope you can help me.... Thanks

Hi, i have noticed something.... it seems like the sound card has nothing to do with the problem, because i also have my system hanging when i use my modem (which is also a pci device), so i guess that the problem is someway related to the pci bus, can anyone help me???
The system works fine when i don't use the sound card or the modem, if i put some music it hangs before the first song ends, and with the modem it takes like 30 miutes to freeze, and i have to reboot.
Wish someone can help me.

HELP - MSI KT6 Delta-LSR

Similar Messages

Maybe you are looking for