Help my hp pavilion g6 is not powering on

Hi pls help me a few nights ago i left the laptop runing during the night and in the morning there was no power no lights anywhere, thought it might me the charger so i tryed with a friend's charger, same thing. there is absolutely no lights anywhere on the laptop. i opened it and i checked the mosfet on the mobo where the power goes in, also the cmos battery and the inlet on the laptop all working. pls help me i fear now that it might be the mobo pls tell me if it can be  anything else. oh and btw i did the whole discharge thing with the power button and not working

It looks like you are not able to Power ON the Notebook and you are trying to fix the issue
Please perform below shown steps to find out if this is a software or hardware issue:
1. Remove all Peripherals and Cables, Disconnect them and try to Power ON the Unit
2. Check for LED Light Status and ensure Power Button spring action is normal
3. Swap with a known good Power Cord, Power Adapter and Battery
4. Incase no Adapter is available, Check if the Power Adapter is slightly warm
Note: This will give us a hint that the Power Adapter might be fine
5. Do you know if the Notebook was in Battery or Power Adapter Mode when you used it for the last time
Note: Ensure there is no liquid spillage or Power Outage
6. Check if the AC Adapter Port is loose/broken
Note: If the Notebook doesn't Power ON even with a known good Power Adapter this confirms the Hardware fault with System Board or the DC Power Circuit
Hope this helps for any further queries reply to the post and feel free to join us again
**Click the KUDOS star on left to say Thanks**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.
Thank You,
K N R K
I work on behalf of HP

Similar Messages

  • HP Pavilion dv7-3080us not powering up. Searching for an HP Repair Centre in Orlando / FL.

    Hi lads from HP community.
    I have an HP Pavilion dv7-3080us which is not powering up and the problems is most probably at the Video Chipset so I’ll definitely need to have it replaced. Since I’m from Brazil and I’ll be in Orlando on vacation for 10 days, I’d like to know if there would be any HP Repair Centre where I could take my Notebook for been fixed at.
    By the way, my Notebook’s configurations is HP Pavilion dv7-3080us, running Windows 7/64 bits, 6 GB RAM and 640 GB Hard Disk and it uses an Integrated Nvidia geforce gt 230m chipset. Computer was bought in May 2010.
    Thanks a million for any help.
    Ricardo.
    This question was solved.
    View Solution.

    Hello rmcunha,
    You need you system repaired.
    There is not a HP repair center that you can take it to, but you can take to one of the big box stores, Best Buy, Office Depot, Staples.
    They are authorized repair centers and will be able to repair the laptop for you.
    Have a good day.

  • HP pavilion dv6 microphone not working . help please . . .

    HP pavilion dv6 microphone not working . help please . . .

    Hi,
    DV6 is a series of hundreads of models, what is yours ? To help us answer question quicker, please read this:
       http://h30434.www3.hp.com/t5/First-Time-Here-Learn-How-to/Welcome-Get-started-here/td-p/699035
    You may wat to try this first:
    1. Right click speaker icon (right hand corner)
    2. Select Microphone devices
    3. Right click Microphone
    4. Enable it
    5. Click Apply/Ok
    Regards.
    BH
    **Click the KUDOS thumb up on the left to say 'Thanks'**
    Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

  • Help!!! My Ipod Shuffle 2nd Gen is not powering up...

    Help!!! My 2nd gen IPod Shuffle is not powering up or charging ...Every time when I plug it in, it simply flashes in Orange for 5 seconds & it goes blank. No other light comes on, it refuses to turn on.
    It also shows up as 'device not recognised' on my PC...It is not charging either. I am unable to acces it via itunes...also I tried my friends same model shuffle & it works just fine & perfect. I used my charger cable & PC on her shuffle and it works out fine. So I figured it has to be a problem with MY IPod...Please help me since this keeps me going everyday...I cant live without my music... I Have tried to reset it, but it doesnt seem to work since no lights are flashing...

    You have done good troubleshooting and have ruled out possible causes, such as a software issue on the computer, problem with USB port, and faulty USB cable.  The remaining cause is a problem on the shuffle, and since this is a 2nd gen shuffle, which is now about 5 or 6 years old (and it sounds like you use it a lot), the most likely explanation is that the shuffle's battery is worn out and has exceeded the max number of charging cycles.

  • HP Pavilion not powering on

    My HP Pavilion tower does not power on.  After a little investigation, all cords were removed from the back of the computer.  Then only the power cord was connected.  When this is done, the LED light on the back of the tower (a little below the power cord outlet ), becomes green - solid green.  When the power switch (at the front) is then pressed, nothing else occurs - in particular, the fan does not run.  When the power cord is disconnected, the LED light stays green for about 5 seconds, and then goes off.  Hope that you have some information.  Thanks. 

    Unfortunatly I don't have a spare good power supply to try.  Since the LED light is solid green (when the power cord is connected), doesn't that indicate that the power supply is probably good?

  • HP Pavilion G4 will not power on.

    Will not power on with or without battery.

    Hi @TJR2 ,
    Thank you for visiting the HP Support Forums and Welcome. It is a great site for information and questions. I have looked into your issue about your  HP Pavilion 17-e118dx Notebook and not powering on with or without the battery connected. Try performing a hard reset.
    When performing a hard reset please note remove any and all USB devices. Disconnect all non-essential devices.
    Here is a link to computer won't start for Windows 8.
    Are you able to hear the fans?
    Please let me know.
    Thanks.
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos, Thumbs Up" on the bottom to say “Thanks” for helping!

  • My HP Pavilion zv6000 will not boot/recovery

    My HP Pavilion zv6000 will not boot/recovery need help

    Disconnect the AC Adapter and Battery from the unit. Hold the Power button down for about 15 seconds. Then without the battery being connected, plug in only the AC Adapter on the unit and check if this powers on the unit. You can also try to reseat the RAM on the unit. You can find the removal procedures on the Service and Maintance guide on www.hp.com for your model notebook. In case the notebook does not work after these steps, it could possibly be a hardware issue on the unit.
    Although I am an HP Employee, I am speaking for myself and not for HP.
    Make it easier for other people to find solutions, by marking my answer “Accept as Solution” if it solves your problem.

  • My Laptop Pavilion 9700 will not recognize DVD/CD drive. Does not show up in Device Manager

    My laptop Pavilion 9700 will not recognize the DVD/CD drive:
    The drive does not show up in the Device Manager’s list:  The disk spins and the light is on: Use a
    paper clip to open the door;  I updated
    to Sevice Pak 2 recently, but I am not sure if this has anything to cause this
    problem:  Please Help, anyone!
    Thanks

    Hi,
    Follow the procedure on the link below to create a bootable Ubuntu CD and follow the steps in Part 3 to 'Try it' to see if this OS will run from the CD without the need to install on your HDD.  This will show whether the problem is with Windows or a Hardware problem with the optical drive.
    http://www.ubuntu.com/desktop/get-ubuntu/download
    Regards,
    DP-K
    ****Click the White thumb to say thanks****
    ****Please mark Accept As Solution if it solves your problem****
    ****I don't work for HP****
    Microsoft MVP - Windows Experience

  • My iphone 5 is not powering the scree, when i connect the iphone to the power it only vibrates

    my iphone 5 is not powering the scree, when i connect the iphone to the power it only vibrates o make the connect sound (is like the sound when you connect the phone to power) and the screen remains black, itunes recognizes the iphone, but i cannot do a hard reset because the power button does not work, and have password in my phone so itunes wond restore it. i want to know if is a hardware problem like the mother board o something. help please

    If you have iOS 7 installed, you can try to restore it via the instructions given by lllaass in https://discussions.apple.com/thread/5634135
    As an alternative, you could take it to an Apple store genius bar and have the techs test it and see what is wrong beyond the failed power button.

  • Copying iMovie back to tape: "your firewire camera is not powered on"

    I'm trying to follow iMovie 6 instructions for copying a movie back to tape.
    I connected my camcorder to the computer with the firewire cable, and it shows up in the Share-->Video Camera menu as an attached device. (It's a Canon Elura 100, btw.)
    So all seems well until I start the procedure, and then I get a "Cannot Export to Camera" error message that says "your firewire camera is not powered on or is not available."
    My ever so slow brain thinks this might have something to do with the fact that I'm using the DV/firewire cable that I used to import the footage into my iMac, and maybe it only sends stuff OUT the firewire end, and won't send video the other way?
    Do I need a different kind of firewire cable?

    Thanks for your assistance!
    I bought this camcorder from Amazon.com (USA) and I have not daisy-chained it anywhere. I've only connected it to one device at a time. It is capable of receiving digital as well as analog video, and can convert analog to digital.
    For example, I used my stereo-video cable to transfer footage from an old VHS tape played by our VCR to my Canon Elura camcorder via the Canon's AV terminal.
    Once the tape was safely transferred into my Canon camcorder, I then plugged my DV/firewire cable into the Canon's DV terminal, and the firewire end of it into the iMac. iMovie saw the Canon camcorder and imported all the footage very nicely.
    Now I would like to transfer the edited footage from iMovie back to a mini DV tape, and my iMovie help file says I can do it, but it's a little sketchy on what cables I should be using.
    The firewire/DV cable I used to send the footage IN to iMovie isn't working to receive the edited footage OUT of iMovie. So maybe I need a different kind of firewire cable?
    Thanks for any help you can offer!

  • How to print to my wireless all in one photosmart prem c410 when printer is not powered on?

    how to print to my wireless all in one  photosmart prem c410 when printer is not powered on?

    Hi,
    You cant print to a printer that you physicly turned off. Most network printer have a sleep mode, so leave it on and after a while it should go into a sleepmode. And should wake up when a printjob is being sent.
    Say "Thanks" by clicking the Kudos Star in the post that helped you.
    Although I work for HP my posts and replies are my own
    Please mark the post that solves your problem as "Accepted Solution"

  • I have pavilion dv6 sound not working hp provide new update idt stil not working

    HI .
    i have pavilion dv6 sound  not working hp provide new update idt stil not working

    Go to the link below.Enter your Product Number as listed on Service Tag attached to bottom of notebook (may be under battery). You can also get the Product Number by pressing Fn + Esc key. After entering PN, click Next ,then choose Software & Drivers.On the next page use the dropdown to select your OS (probably Windows 7 64bit). A list will populate with drivers. Download & Save the latest Audio driver.
    http://h10025.www1.hp.com/ewfrf/wc/siteHome?cc=us&lc=en
    Go to Control Panel,Programs & Features-Uninstall IDT software and restart the laptop.Next install using the downloaded file.
    ```````````````````````````````````````
    If still no sound,try a hard reset, works sometimes.Disconnect all external devices first.
    1-remove power cord and battery
    2-press power button for 30 seconds
    3-reinstall only power cord for first startup.
    4-power on
    ******Clicking the Thumbs-Up button is a way to say -Thanks!.******
    **Click Accept as Solution on a Reply that solves your issue to help others**

  • Iphone suddenly gone blank. Not powering on

    iphone suddenly gone blank. Not powering on. Any suggestions?

    Hello Navalagarwal,
    The following article contains a few steps that may help get your iPhone powered back on.
    iPhone, iPad or iPod touch: Not responding or does not turn on
    http://support.apple.com/kb/TS3281
    Best regards,
    Allen

  • E540: Not powering up

    Few months old E540 is not powering up. When I press the power button, the led is lit and the fan turned on but nothing else happens. Nothing on screen and can't even open the DVD tray. Have tried fn+F8, removing battery without luck. Haven't done anything special recently or installed any new software. What next ? Any help is greatly appreciated.  

    Good day and welcome to the community.
    Please have a look at this Knowledgebase article:
    https://forums.lenovo.com/t5/11e-Windows-E-and-Edge-series/E540-Cannot-power-up-the-system/ta-p/1497840
    Does this seem aplicable to your situation?
    Regards.

  • Playbook not powering up, not charging, nothing

    My BB playbook is not powering up when placed in the charging cradle or when plugged into a computer.  I have tried hard restart and all kinds of  things - I am not even getting a red light.
    is there any way I can get it restarted, rebooted, or something so that it can take a charge.  I know it has to be powered up to charge - but right now nothing is working.  Please help!

    paulmitt wrote:
     but is there a chance that my playbook is just finished ....:
    Nope! It's just deeply and severely drained, and you'll notice references to that in the KB articles I linked for you.
    This happened on one of my PlayBooks recently, and it too some patience and work...if it's not TOO deeply drained, you will begin to see some life eventually via the no battery icon, or a low orange glowing pulsating LED at the top of the device.
    If it is VERY deeply drained, you will need to eventually use the PlayBook debricking method to bring it back to life. You will lose all media, pictures, etc., on the device however, if you have not made a previous backup.
    Try this, while connected to your charger. Press and hold the Power key, up and down volume (-/+) all three buttons simultaneously, for about 10-12 seconds. You should the red LED blink and that should allow a reset of the PlayBook and to power up.
    After charging 24+ hours:
    1- Press the powerbutton for about 20 seconds
    2- Charge PB for 2 minutes (use stopwatch)
    3- Disconnect powercable for 8 seconds
    You have to repeat step 2 and 3 total of 10 times. Then reboot by pressing power and + key for 22 seconds.
    Other users have reported this reset their device and got it working.
    You need to follow these instructions to "debrick" your PlayBook:
    1. (skip this if the devce is dead due to no battery charge) Do a backup of your PlayBook using your computer and BlackBerry Desktop Software version 7 installed. It can be downloaded from http://us.blackberry.com/apps-software/desktop/
    2. (skip this if the devce is dead due to no battery charge) Unplug the PlayBook and on the PlayBook press and hold down the power button until the unit forces the device off.
    3. With the Desktop Software still open on your computer and the PlayBook powered off, connect the PlayBook to your computer once again.
    4. You should see an error screen from Desktop Software popup with the options to Retry, Update, or Cancel.
    Very quickly choose the Update option.
    5. All information will on your PlayBook will be erased and a reload of the Software will commence to install on the PlayBook.
    6. Once this is complete your PlayBook will go back through the initial (as if new) setup wizard (entering the BlackBerryID, etc., and then you can perform a restore using Desktop Software to return your personal data from the backup. Applications which you downloaded from AppWorld won't restore, but they can be easily reinstalled using AppWorld > MyWorld section of AppWorld.
    1. If any post helps you please click the below the post(s) that helped you.
    2. Please resolve your thread by marking the post "Solution?" which solved it for you!
    3. Install free BlackBerry Protect today for backups of contacts and data.
    4. Guide to Unlocking your BlackBerry & Unlock Codes
    Join our BBM Channels (Beta)
    BlackBerry Support Forums Channel
    PIN: C0001B7B4   Display/Scan Bar Code
    Knowledge Base Updates
    PIN: C0005A9AA   Display/Scan Bar Code

Maybe you are looking for