HELP MY iBOOK G4 WONT BOOT I GET FOLDER WITH FINDER LOGO AND QUESTION MARK

HELP I have an iBook G4 and it frose so I shut it down by pressing power button and then it would kind of start up I would get a chime and a gray screen would come on for one second and the switch to another gray screen with a folder in the middle the has a finder logo that switches off between a question mark. But the funny thing is i started up yesterday and after four trys it worked then it froze again and i had to turnit off again it did the same thing i would just boot drom the leopard cds but they are missing. And its not like this was an on going problem it use to work fine.

Do you have the restore disks that came with the iBookG4? Without the Leopard disk, or the restore disks that came with your iBook, it's going to be difficult to trouble shoot.
Usually the "question mark folder" means your Mac can't find a System Folder to boot from. Make sure the iBook is shut down. Press the power button, insert the restore disk and hold down the C key all at the same time. Keep holding down the C key until you see the Apple logo. An Installer window will open. Select English, but DO NOT proceed with any installations. Instead, from the Menu Bar, click Utilities/Startup Disk. When the Startup Disk window opens, select MacintoshHD 10.x.x in the window and then click Restart. If the drive is functioning properly, it should boot back up from the internal disk.
Carolyn
Message was edited by: Carolyn Samit

Similar Messages

My iMac wont go past the grey screen with Apple Logo and question mark a caution mark

My iMac wont go past the grey screen with Apple Logo and question mark a caution mark

You may find this support article helpful:
http://support.apple.com/kb/TS2570
Ciao.

HT1948 USB drive with install image is showing in Startup Manager on a Mac Pro, but wont boot. Showing circle with cross strip, and shut down automatically. USB device are made and work on two different MacBook Pro, but used on Mac Pro. Any help?

USB drive with install image is showing in Startup Manager on a Mac Pro, but wont boot. Showing circle with cross strip, and shut down automatically. USB device are made and work on two different MacBook Pro, but used on Mac Pro. Any help?

OS X installers have always been fairly specific, hardware-wise. I haven't read anything reflecting that situation with the Recovery HD, so it may be that the Recovery HD created for the MacBook Pro does not have the necessary drivers for the Mac Pro. Obviously, nothing definitive here, but a possibility.

Wont boot up. folder with ?

I have a white screen and my computer want boot up. It has a folder with a question mark. Help

Hi Rhonda
Work thru the steps in the > A flashing question mark appears when you start your Mac article.
Then if it still does not startup, move onto the > Intel-based Macs: Using Apple Hardware Test article.
Dennis

Macbook won't boot past grey screen with Apple logo and spinning wheel.

For some reason, after about 1 year and 10 months of owning my Macbook, it decided this morning not to load past the grey screen with the Apple logo and spinning cog/wheel.
I used it for a couple of hours beforehand, and it was working fine. Software Update prompted me of about about 4 or 5 updates; I can't remember exactly what was downloaded, but I think there was a Security Update and iTunes among them. I restarted, left it to install with no errors, but when I logged in, Safari and iTunes were running incredibly slowly. I also noticed that the volume keys weren't responding, as well as the power key to bring up the "Sleep, Restart, Shutdown, etc" dialog box. I forced shutdown, hoping a restart would solve my problem, and that's when my troubles started. I originally just left it, but after about an hour the wretched thing was still spinning.
So far, I have done a number of troubleshooting tips on a variety of websites. I have tried taking the battery out and holding down power for 5 seconds, resetting the PRAM with option, cmd, p & r, and holding down power until the sleep light flashes rapidly and the computer lets out a large "BOOOP".
I have booted off my Leopard install disk with both option and c, repaired the hard drive a number of times, with there being no errors whatsoever. I have tried repairing permissions, but everything seems to freeze up, except the mouse.
For some reason my computer will not boot into safe mode, either, and holding cmd & s at startup doesn't get me to the stage where I can enter commands with the keyboard.
Unfortunately, because of my puny 60GB hard drive, I only have 1GB of free space left and cannot reinstall Leopard without wiping my hard drive.
I would greatly appreciate it if anyone could assist me with this unfortunate dilemma. It's such a shame that my computer has been fantastic for so long and now decides to play up. (Maybe it's just Apple trying to get me to buy a new 2.4Ghz aluminium Macbook sooner than I was planning...)
Thanks very much.

Hi ds,
Sorry to hear you're having such trouble!
Unfortunately, the best thing you can do at this point is reinstall Leopard (and then attempt to install the combo updater, too). If you don't have a backup of your machine, you could boot it into Target Disk Mode (by holding down T at startup) and then attach it via FireWire to another computer to salvage your files.
I recently had to repair a machine with this exact same problem, and after messing around with that for several hours, I'd have to say that I think that an Erase and Install is the way to go. If you then migrate over your user data and start having troubles, you at least know where the problem lies. I suspect, though, that having a clean machine with all of the new updates applied will be the end of the issue.
Sorry to be the bearer of bad news. There are a few other things you could try first; you could, for example, manually download the relevant combo updater from Apple's website and attempt to install it to your damaged machine while it's in Target Disk Mode. If you have a copy of Disk Warrior, that too is certainly worth a shot (and in some cases may be the saving grace). In my experience, though, a failure of this magnitude isn't easy to resolve.
Hope that helps.
—Hazy

Macbook Pro won't boot past grey screen with Apple logo and then shuts off

This is a long story...
This morning, I would turn it on and it'd go to the grey screen with the Apple logo for a few seconds and then go to the icon that is a circle with a line through it. After reading online, I was able to boot it up in Safe Mode. I messed around a little bit in system preferences thinking I could fix it on my own, not really knowing what I was doing (I'm a *******). I went to Startup Disk in Preferences. I chose the MAC OS X, xxxx and then clicked the lock to prevent further changes and then clicked restart.
Now when I turn on the macbook, it goes to the grey screen with the Apple logo for at least two-three minutes and then just shuts off. Won't boot into Safe Mode now. Please help. I already tried the Command-Option-P-R keys trick like five times.

If you have a full retail DVD for 10.6 you can boot from that by holding the C key during startup...but you will then be in install mode if that is what you want to do. At least go ahead and see if it will boot ok from the 10.6 disk and then you can decide what you want to do further.
Apple does not have 10.5 for sale anymore from what some other users have said on here so if you want to go that route you will have to find a copy for sale such as from eBay or one of the Mac resellers.
Before taking the machine to someone, try booting from 10.6 and see if that works...that way you can narrow down problems the machine may be having.

My iphone wont boot is just displays the apple logo and some small typing

My iphone is frozen and is only displaying the black screen with the apple logo with some small white text

This is what I am referring to. See the red circle. This is when responding to this forum.
Try this support document for when you cannot update or restore. See if that helps you. http://support.apple.com/kb/HT1808

Wont boot up. small folder on the screen flashing ? mark

It powers up and chimes. but screen is grey and after awhile a little folder apears in the center of the screen. it has a two tone color face in the center of the folder. can anyone help thanks robert

Hi,
Welcome to the Discussions.
That means it can't find a valid System Folder to start from. It could be a damaged directory or the drive itself may be damaged.
Put the install disc in the drive and hold down the "c" key as soon as you hear the chime. Use Disk Utility to repair the drive. If it reports errors and repairs repeat it until no errors (in red) are reported. If it reports errors it can't repair post the message here.
Also please open My Settings on the right of this page and enter the model of your computer as well as the OS it's running. It helps in troubleshooting.
John

Boots to gray screen with apple logo and no spinning wheel

For some reason, all my programs that were open (Safari, iTunes) were not responding and the spinning color wheel appeared. I simply pressed down on my power button to reset my laptop.
Soon after my laptop booted to a gray screen with the apple logo. There was no spinning wheel. I did here the chime noise and my screen remains like this as we speak.
I tried to use my install CD but nothing changes on my screen.
Please advise.

Uh-oh, that's not good. What exactly did you do when you put your install CD in? Did you make sure to hold down the "C" key on the keyboard to startup from it?
From there, you can try Disk Utility to see if the hard drive needs to be repaired.
MAKE SURE YOU DON'T USE TECHTOOL DELUXE that came with AppleCare if you have it. There is a glitch--I learned the hard way... had a kernel panic on my PowerMac G4 last week and the drive went from bad to worse... it's here on the Apple forums somewhere--that causes the directory on the affected volume to go unreadable.
Using DiskWarrior won't help either.
If Apple's Disk Utility can't help you, I recommend backing up your data (if you can see it with another Mac under Target Disk Mode--hold down the "T" key on the keyboard and startup while connected to another Mac via FireWire--take your files off that way) and then using Data Rescue II.
It saved my behind. TechTool Deluxe ruined my drive, DiskWarrior couldn't help, but Data Rescue II did. Best $99 I ever spent! It's at the Apple Store, or available online.
That is, if it comes to all of this. Try restarting from your installation CD (restore disc) if you haven't done so already, and use Disk Utility to see what it reports. If it says repair, do so. Apple's Disk Utility won't ruin it... only TechTool Deluxe (from the AppleCare package).

IBook G4 wont boot

My iBook won't boot it gets as far as the apple logo with the spinning wheel. It'll be like that for about four minutes then it'll restart and repeat its self. I've tried the safe mode but no luck and I do not have the original disc installers. Im running leopard off of it and just before this happened Safari was not responding at all every time I tried to open it, so I do not know if it's related or not.
If you have any info on how I can get it to turn back on or idea of what might be causing this problem, I would be very grateful.
Thanks Coyote

Hello,
Since you do not have your restore disk nor a Leopard disk, your options are limited for repairing the boot disk yourself but here goes ...
Try booting while holding down the Option key and try to access the Startup Manager:
Startup Manager: If you can boot using the Startup Manager, select the 10.5.x.
Or, if you have a Firewire cable, you could try booting in Safe Mode and try to access the iBook hard disk from another Mac: How to use Firewire Target Disk Mode
Or... Mac OS X: How to start up in single-user or verbose mode *Note ... you should only try this if you are comfortable using UNIX commands*
*"I've tried the safe mode but no luck"* What exactly happened when you booted in Safe Mode?
You can get replacement System Install & Restore CD/DVDs from Apple's Customer Support - in the US, (800) 767-2775 - for a nominal S&H fee. You'll need to have the model and/or serial number of your Mac available.
If you're not in the US, you may need to go through the regional Apple Store that serves your location to find the contact number. Here's a list of links to all of those -
http://store.apple.com/Catalog/US/Images/intlstoreroutingpage.html
Carolyn
Message was edited by: Carolyn Samit

Imac wont boot - i get a white screen with apple logo, and it loads to about 10%, then screen goes black

imac wont boot - i get a white screen with apple logo, and it loads to about 10%, then screen goes black

Hey there mtriest,
It sounds like you are unable to boot the iMac successfully as it keeps shutting down when you try to boot. I suggest the troubleshooting from the following article named:
Mac OS X: Gray screen appears during startup
http://support.apple.com/kb/ts2570
Disconnect, test peripheral devices and network cables
Note: "Peripheral devices" refers to external devices other than what came with your Mac, such as hard drives, printers, or hubs that you connect via a USB or FireWire cable.
Shut down your Mac. If necessary, hold your Mac's power button for several seconds to force it to power down.
Disconnect all peripheral devices such as external hard drives or printers (leave only the display, a keyboard, and mouse connected).
Disconnect any Ethernet cables.
Start up your Mac.
If you can start up this way, one or more of your peripheral devices (or installed software related to the device) is probably causing the gray screen issue. Connect one device, then restart your Mac to test for the issue. Repeat the process until you locate the device at issue. Make sure the device is powered if it needs to be to operate correctly. Check with the manufacturer of the device for support or possible software driver or firmware updates that may be available for the device. Try a different cable with the device if possible (such as a different USB or FireWire cable).
Note: If you have multiple peripheral devices and the issue only occurs when they are all connected, but not when each device is the only peripheral connected, see the Additional Information section below.
If you are using a desktop Mac with a third-party keyboard and/or mouse device, and the issue still occurs, try starting up with an Apple keyboard and mouse connected instead. Try starting with no keyboard and mouse connected, then connect them after start up. Also, try a different USB port on your Mac.
If the gray screen issue persists with no devices connected, go to the next section (with the peripherals still disconnected).
Perform a Safe BootSimply performing a Safe Boot may resolve this issue.
Shut down your Mac. If necessary, hold your Mac's power button for several seconds to force it to power down.
Start your Mac, then immediately hold the Shift key. This performs a Safe Boot. Advanced tip: If you want to see the status of a Safe Boot as it progresses, you can hold Shift-Command-V during start up (instead of just Shift).
Note: A Safe Boot takes longer than a typical start up because it includes a disk check and other operations.
If your Mac starts up as expected, immediately try restarting.
If the Safe Boot does not work, or the restart after a successful Safe Boot does not work, go to the next section.
There is additional information in the article with further troubleshooting if needed.
Thank you for using Apple Support Communities.
Cheers,
Sterling

I switch on my mac book pro and all i get is the apple logo and below a loading wheel , but its stuck there for like an hour !!! help??

i switch on my mac book pro and all i get is the apple logo and below a loading wheel , but its stuck there for like an hour !!! help??

Take each of these steps that you haven't already tried. Stop when the problem is resolved.
Step 1
The first step in dealing with a boot failure is to secure your data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since your last backup, you can skip this step.
There are several ways to back up a Mac that is unable to boot. You need an external hard drive to hold the backup data.
a. Boot into the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.”
b. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, boot the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
c. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. The easiest way to deal with the problem is to boot from an external drive, or else to use either of the techniques in Steps 1b and 1c to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
Step 3
Sometimes a boot failure can be resolved by resetting the NVRAM.
Step 4
If you use a wireless keyboard, trackpad, or mouse, replace or recharge the batteries. The battery level shown in the Bluetooth menu item may not be accurate.
Step 5
If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
Step 6
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to boot, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can boot now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Step 7
If you've booted from an external storage device, make sure that your internal boot volume is selected in the Startup Disk pane of System Preferences.
Boot in safe mode. Note: If FileVault is enabled, or if a firmware password is set, or if the boot volume is a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to boot and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you boot in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, your boot volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 6.
If you can boot and log in now, empty the Trash, and then open the Finder Info window on your boot volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then reboot as usual (i.e., not in safe mode.)
If the boot process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 8
Launch Disk Utility in Recovery mode (see Step 1.) Select your startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then reboot as usual.
Step 9
Reinstall the OS. If your Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 10
Repeat Step 9, but this time erase the boot volume in Disk Utility before installing. The system should automatically reboot into the Setup Assistant. Follow the prompts to transfer your data from a Time Machine or other backup.
Step 11
This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a boot failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 12
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider.

HT201441 i bought my iphone secondhand, and the previous owner didnt deltete his find my iphone account, so when i restored it i know cant access my phone, i need help as i have no way of getting intouch with the previous owner whatsoever :/ help!

i bought my iphone secondhand, and the previous owner didnt deltete his find my iphone account, so when i restored it i know cant access my phone, i need help as i have no way of getting intouch with the previous owner whatsoever :/ help!

Welcome to the Apple community.
Unfortunately, you cannot do very much with your phone unless you get assistance from the previous owner, they should either provide you with the password to unlock it or remove their account from the phone entirely remotely through iCloud.com > Find My Phone.

Macbook Pro (2011) froze while working, forced shut down, now won't turn on. Grey screen with apple logo and spinning wheel for hours. Help?

Macbook Pro (2011) froze while working, forced shut down, now won't turn on. Grey screen with apple logo and spinning wheel for hours. Help?
Unfortunately do not know the operating system since I never updated anything and I can't get in to it.
Thanks for your assistance.

If you want to preserve the data on the boot drive, and it's not already backed up, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data, you can skip this step.
There are several ways to back up a Mac that is not fully functional. You need an external hard drive to hold the backup data.
1. Boot from the Recovery partition or from a local Time Machine backup volume (option key at startup.) Launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.”
2. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, boot the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
3. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.

I need to reinstall my operating system for 10.5 after seeing a file folder and question mark flashing on my start up screen. Can anyone help me with this?

I need to reinstall my operating system for 10.5 after seeing a file folder and question mark flashing on my start up screen. Can anyone help me with this?

Hello,
That means it can find the Hard Drive, or can't find the things needed for booting.
See if DU even sees it.
"Try Disk Utility
1. Insert the Mac OS X Install disc, then restart the computer while holding the C key.
2. When your computer finishes starting up from the disc, choose Disk Utility from the Installer menu at top of the screen. (In Mac OS X 10.4 or later, you must select your language first.)
*Important: Do not click Continue in the first screen of the Installer. If you do, you must restart from the disc again to access Disk Utility.*
3. Click the First Aid tab.
4. Select your Mac OS X volume.
5. Click Repair Disk, (not Repair Permissions). Disk Utility checks and repairs the disk."
http://docs.info.apple.com/article.html?artnum=106214
Then try a Safe Boot, (holding Shift key down at bootup), run Disk Utility in Applications>Utilities, then highlight your drive, click on Repair Permissions, reboot when it completes.
(Safe boot may stay on the gray radian for a long time, let it go, it's trying to repair the Hard Drive.)

HELP MY iBOOK G4 WONT BOOT I GET FOLDER WITH FINDER LOGO AND QUESTION MARK

Similar Messages

Maybe you are looking for