Help my laptop won't start up - I just get a white screen

My laptop won't start up - I've tried restarting it a few times but all I get is a white screen. Any suggestions?

Similar Messages

My macbook pro won't start up. I get the white screen and the grey apple icon   the spinning wheel......and it doesn't change !

My macbook pro won't start up. I get the white screen and the grey apple icon   the spinning wheel......and it doesn't change !

Take each of these steps that you haven't already tried. Stop when the problem is resolved.
To restart an unresponsive computer, press and hold the power button for a few seconds until the power shuts off, then release, wait a few more seconds, and press it again briefly.
Step 1
The first step in dealing with a startup failure is to secure the data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since the last backup, you can skip this step.
There are several ways to back up a Mac that is unable to start. You need an external hard drive to hold the backup data.
a. Start up from the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.” The article refers to starting up from a DVD, but the procedure in Recovery mode is the same. You don't need a DVD if you're running OS X 10.7 or later.
b. If Step 1a fails because of disk errors, and no other Mac is available, then you may be able to salvage some of your files by copying them in the Finder. If you already have an external drive with OS X installed, start up from it. Otherwise, if you have Internet access, follow the instructions on this page to prepare the external drive and install OS X on it. You'll use the Recovery installer, rather than downloading it from the App Store.
c. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, start the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
d. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. You might be able to start up in safe mode even though you can't start up normally. Otherwise, start up from an external drive, or else use the technique in Step 1b, 1c, or 1d to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
Step 3
Sometimes a startup failure can be resolved by resetting the NVRAM.
Step 4
If a desktop Mac hangs at a plain gray screen with a movable cursor, the keyboard may not be recognized. Press and hold the button on the side of an Apple wireless keyboard to make it discoverable. If need be, replace or recharge the batteries. If you're using a USB keyboard connected to a hub, connect it to a built-in port.
Step 5
If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
Step 6
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to start up, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can start up now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Step 7
If you've started from an external storage device, make sure that the internal startup volume is selected in the Startup Disk pane of System Preferences.
Start up in safe mode. Note: If FileVault is enabled in OS X 10.9 or earlier, or if a firmware password is set, or if the startup volume is a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to start and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know the login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you start up in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, the startup volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 11. If you ever have another problem with the drive, replace it immediately.
If you can start and log in in safe mode, empty the Trash, and then open the Finder Info window on the startup volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then restart as usual (i.e., not in safe mode.)
If the startup process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 8
Launch Disk Utility in Recovery mode (see Step 1.) Select the startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then restart as usual.
Step 9
If the startup device is an aftermarket SSD, it may need a firmware update and/or a forced "garbage collection." Instructions for doing this with a Crucial-branded SSD were posted here. Some of those instructions may apply to other brands of SSD, but you should check with the vendor's tech support.
Step 10
Reinstall the OS. If the Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 11
Do as in Step 9, but this time erase the startup volume in Disk Utility before installing. The system should automatically restart into the Setup Assistant. Follow the prompts to transfer the data from a Time Machine or other backup.
Step 12
This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a startup failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 13
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider.

Help! Laptop won't start up- startup repair goes to black screen!

Hi! Just wondering if anyone can help me with my toshiba laptop C650-152! I was online yesterday when my laptop froze and in the end i had to turn it off by cutting the power source! Today I have tried to turn it on and It keeps going to a black screen with white writing which asks if I want to Start it normally or do startup repair! If I press start normally it gets me to the windows start up screen (with the coloured logo) but then gets stuck there. If i press start up repair it goes to a black screen with a White mouse cursor and gets stuck there too! I can use a laptop just fine but am pretty clueless when it comes to technical matters so if anyone could help explain what I should do (in laymens terms) it would be much appreciated!! Thanks in advance for your help! Beth

To burn the disc from an ISO file, Beth, you may need a third-party utility depending on the version of Windows. I use the free BurnCDCC burning program from here.
TeraByte Unlimited Freeware
To use the disc do I just turn my laptop on..?
Something like this. Turn the computer on, load the disc, turn the computer off, start it again and then press F12 to get the boot-priority men, select the optical drive, follow the instructions (like choose a language and a Windows installation), and you're on your way to the Windows Recovery Environment.
Then will a menu appear so I can choose to do a system restore or do I have to search for it? Finally will doing a 'system restore' delete any of my saved data such as photos/music/uni work?
All that was answered at the link I already gave you.
What are the system recovery options in Windows 7?
Click Show All. Under System Restore, click the links What is System Restore and System Restore: frequently asked questions. No data files are disturbed by System Restore.
-Jerry

On start up i just get a grey screen with the apple logo-this has suddenly started happenin. Please help?

on start up i just get a grey screen with the apple logo-this has suddenly started happenin. Please help?

Take each of these steps that you haven't already tried. Stop when the problem is resolved.
To restart an unresponsive computer, press and hold the power button for a few seconds until the power shuts off, then release, wait a few more seconds, and press it again briefly.
Step 1
The first step in dealing with a startup failure is to secure the data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since the last backup, you can skip this step.
There are several ways to back up a Mac that is unable to start. You need an external hard drive to hold the backup data.
a. Start up from the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.” The article refers to starting up from a DVD, but the procedure in Recovery mode is the same. You don't need a DVD if you're running OS X 10.7 or later.
b. If Step 1a fails because of disk errors, and no other Mac is available, then you may be able to salvage some of your files by copying them in the Finder. If you already have an external drive with OS X installed, start up from it. Otherwise, if you have Internet access, follow the instructions on this page to prepare the external drive and install OS X on it. You'll use the Recovery installer, rather than downloading it from the App Store.
c. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, start the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
d. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. You might be able to start up in safe mode even though you can't start up normally. Otherwise, start up from an external drive, or else use the technique in Step 1b, 1c, or 1d to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
Step 3
Sometimes a startup failure can be resolved by resetting the NVRAM.
Step 4
If a desktop Mac hangs at a plain gray screen with a movable cursor, the keyboard may not be recognized. Press and hold the button on the side of an Apple wireless keyboard to make it discoverable. If need be, replace or recharge the batteries. If you're using a USB keyboard connected to a hub, connect it to a built-in port.
Step 5
If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
Step 6
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to start up, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can start up now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Step 7
If you've started from an external storage device, make sure that the internal startup volume is selected in the Startup Disk pane of System Preferences.
Start up in safe mode. Note: If FileVault is enabled in OS X 10.9 or earlier, or if a firmware password is set, or if the startup volume is a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to start and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know the login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you start up in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, the startup volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 11. If you ever have another problem with the drive, replace it immediately.
If you can start and log in in safe mode, empty the Trash, and then open the Finder Info window on the startup volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then restart as usual (i.e., not in safe mode.)
If the startup process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 8
Launch Disk Utility in Recovery mode (see Step 1.) Select the startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then restart as usual.
Step 9
If the startup device is an aftermarket SSD, it may need a firmware update and/or a forced "garbage collection." Instructions for doing this with a Crucial-branded SSD were posted here. Some of those instructions may apply to other brands of SSD, but you should check with the vendor's tech support.
Step 10
Reinstall the OS. If the Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 11
Do as in Step 9, but this time erase the startup volume in Disk Utility before installing. The system should automatically restart into the Setup Assistant. Follow the prompts to transfer the data from a Time Machine or other backup.
Step 12
This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a startup failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 13
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider.

`my macBook Pro won't start up. Just get that gray blueshy kind of screen and don't go nowhere.

My MacBook Pro won't start up. Just get that gray, blueishy screen and don't go on.

Try a safe boot.
http://support.apple.com/kb/TS2570
This boot takes longer than a normal boot, be patient. If it boots login, and see if it seems normal. If so, logout and reboot normal.

My iMac won't boot. I only get a white screen. Won't open in safe mode or recovery mode. Any suggestions?

Hey, any help? My 24" iMac won't boot. I only get a white screen when turning on. It won't open in safe or recovery mode. Any suggestions?

If you can't boot from your installer DVD, then take it in for service.

My imac won't boot up. I get a white screen with the apple logo and the spinning spiral--any ideas?

my imac won't boot up. I get a white screen with the apple logo and the spinning spiral--any ideas?
I have started having trouble since i had to upgrade OS the latest in July 12.

http://support.apple.com/kb/TS2570 Follow this article and when it gets to the part where you go into disk utility using your install disc, you'll actually boot up holding down Command and R

I can access my music library, but not the Itunes store. Just getting a white screen. It starts to connect but just stops. Any suggestions?

I can access my music library, but Itunes Store is not opening. I am just getting a white screen. Any suggestions?

Reset the device:
Press and hold the Sleep/Wake button and the Home button together for at least ten seconds, until the Apple logo appears.
If that doesn't help, tap Settings > General > Reset > Reset All Settings
If that didn't help, tap Settings > General > Reset > Reset Network Settings
You will have to re enter the Wi-Fi password.
If that doesn't help, try here > iOS: Troubleshooting Wi-Fi networks and connections
No data is lost due to a reset.

The only way to get lion to start is to hold the eject button down, otherwise I just get a white screen. Any cures?

The only way to get lion to start is to hold the eject button down, otherwise I just get a white screen. Any cures?
this is what I'm running on ?
Processor 2 x 2.8 GHz Quad-Core Intel Xeon
Memory 12 GB 800 MHz DDR2 FB-DIMM
Graphics NVIDIA GeForce 8800 GT 512 MB
Software Mac OS X Lion 10.7.2 (11C74)

thanks,
I tried and it worked once, then went back to the white screen, so I'm back to hollding down the eject button.
thank you anyway.
K

Mavericks won't start after reboot, just getting circular icon seems like forever.

Hello,
Did a shutdown in the evening, and when restarted I just get the circular icon under the grey apple. Tried PRAM reset. Tried Option-retart.
Suggestions? Thanks in advance.

Take each of these steps that you haven't already tried. Stop when the problem is resolved.
Step 1
The first step in dealing with a boot failure is to secure your data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since your last backup, you can skip this step.
There are several ways to back up a Mac that is unable to boot. You need an external hard drive to hold the backup data.
a. Boot into the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.”
b. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, boot the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
c. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
Sometimes a boot failure can be resolved by resetting the NVRAM.
Step 3
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to boot, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can boot now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
If you've booted from an external storage device, make sure that your internal boot volume is selected in the Startup Disk pane of System Preferences.
Step 4
Boot in safe mode. Note: If FileVault is enabled on some models, or if a firmware password is set, or if the boot volume is a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to boot and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you boot in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, your boot volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 5.
If you can boot and log in now, empty the Trash, and then open the Finder Info window on your boot volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then reboot as usual (i.e., not in safe mode.)
If the boot process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 5
Launch Disk Utility in Recovery mode (see Step 1.) Select your startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then reboot as usual.
Step 6
Reinstall the OS. If your Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 7
Repeat Step 6, but this time erase the boot volume in Disk Utility before installing. The system should automatically reboot into the Setup Assistant. Follow the prompts to transfer your data from a Time Machine or other backup.
Step 8
This step applies only to older Macs (not current models) that have a logic-board ("PRAM") battery. Both desktop and portable Macs used to have such a battery. The logic-board battery is separate from the main battery of a portable. A dead logic-board battery can cause a boot failure. Typically the boot failure will be preceded by loss of the startup disk and system clock settings. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 9
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store to have the machine tested. If you can't get to an Apple Store, go to another authorized service provider.

What do I do when I start my iMac I get a white screen with an apple and a moving circle?

All I get when my iMac is turned on is a white screen with an apple and a moving circle. What should I do to get the iMac to boot?

Do you have reliable backup you can restore from, as an erase and re-install may be required?
Before you got down that route, it's possible that it might get fixed if you try again. Not sure about that particular error, but I have had errors in the past that Disk Utility wouldn't fix on the first attempt but then subsequently did.
It's also possible that the (around $99, I think) Disk Warrior might resolve it - but not guaranteed.
However, I just found this thread: https://discussions.apple.com/thread/3862376?start=15&tstart=0 have a look at Nirvi's post at the end - there may be hope (I've not tried this, although it seems to have helped a few, although not everybody - so at your own risk and I wouldn't try it if I didn't have backup).

Laptop won't start up - I just got it

I just recieved my laptop in the mail today, and when I tried to start it up, the power would come on, and it would start to say it was loading OS X, but the blue bar would barely even move before it disappeared and just showed me the light blue screen that flickered every few moments. I let it sit there thinking mabye it was working on something, but nothing ever showed up. And I can't eject the CD thing, so it's not like I can put in the OS X Install Disk 1. What's going on?

Hi kirara,
did that happen when you tyr to start it up for the first time?
and what disk inside the optical drive (if there is any)?
Try to turn everything off, unplugged the power adapter and take off the battery, and press and hold your power button for 5 second, and put your battery back and plug the mag safe back. and restart the macbook.
If it still won't boot up, try to restart and insert the installer disk 1 right away (if there is nothing in your optical drive) and press alt/option key and select start up from disk.
If start up from disk is the only option, then your HD must be failed or corrupted and need to be repaired or replaced. Could be from rough shipment.
But since you just got it, why don't you just visit apple store or call them and ask for new replacement.
Good Luck.

IMac won't start... Stick on white screen

Hi,
My Late 2009 iMac won't boot. It switches on, chimes and that's it. There is no apple logo, and flashing folder.
I have reset the SEC and PRAM several times.
I have tried booting to a CD, it does not work.
It will not run the hardware test, either from the HD or from CD.
Does anybody have any suggestions?
Regards Lee

Thanks for your advance, before I got chance to try it I have done the following;
I had stopped my original HDD out for a SSD a few months ago. Decided to the old HDD back in, that still had a copy of Lion on it. It now boots up and seems to be working fine. I'm doing a n extended hardware test now to see if it picks anything up.
I have a external FireWire HDD caddy, I'll test the SSD in that once the extended hardware has finished.
The plot thickens... But at least it's working again!!

My iMac freezes at start. I just get the gray screen and apple symbol.

I turned it off and on and then nothing. Just gray screen and spinning wheel. I also see the mouse pointer.

Reinstall OS X without erasing the drive
Do the following:
1. Repair the Hard Drive and Permissions
Boot from your Snow Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
2. Reinstall Snow Leopard
If the drive is OK then quit DU and return to the installer. Proceed with reinstalling OS X. Note that the Snow Leopard installer will not erase your drive or disturb your files. After installing a fresh copy of OS X the installer will move your Home folder, third-party applications, support items, and network preferences into the newly installed system.
Download and install the Combo Updater for the version you prefer from support.apple.com/downloads/.

Laptop won't start up! please Help

Hello, Can someone help me with my laptop. I have mac os x 10.2x. It completely froze and and i shut it down. When i press on the power button to start it i just got a white screen with grey apple sign with little wheel spins around, and nothing is happening. please helpppppppppp.

You can't have 10.2 on a MacBook, it came with Tiger (10.4) installed ??
Boot holding down Apple/S and don't let go until you see scrolling text.
When that stops and you see a root#: prompt enter
fsck -fy
Let it run through all the checks and repairs.
If it fails first time, at any time, or finds and fixes a fault - run the command again and keep doing so (some fixes can take several passes) until it says "Appears to be OK" then enter
reboot

Help my laptop won't start up - I just get a white screen

Similar Messages

Maybe you are looking for