HELP!!! my laptop wont start after water went inside the key board

accidental spillage of water on the keyboard and my laptop is dead. i have been to authorised service center but every one is saying the warranty is void if there is any physical damage. can any one let me know what should i dooooooooo!!!!!!!!!!

Yes, the warranty is voided by the water damage. You have probably done a number on the motherboard, which will need diagnosis and repair.
You should be either 1) thankful that you have recent backup or 2) hopeful that your hard drive itself was not damaged and the data is recoverable.

Similar Messages

My apple laptop wont start up. I get the music of opening and then a brief flicker of light then a black dead screen

my mac laptop wont start up. It briefly plays the starup music, then a brief flicker of light followed by a black dead screen.
The power is connected so no trouble there...

I hope the link helps and Thank You for the reply.
I am an HP employee.
Please post rather than sending a Private Message. It's good for the community and I might not be able to get back quickly.- Thank you.
Please click the White Kudos star on the left to say thanks.
Please mark Accept As Solution if this resolves your issue.

Imac wont start after electricity went off, no power surge. Apple Hardware Test ,no trouble found, please can anyone help,thanks ,Andy

Hi, please can anyoner help. I had a power cut at home and went to switch the imac back on and all i can get is a grey screen, a chime and a circle going around but no blue screen when I start up .I have tried pressing the power button for ten seconds with it switched off .Tried installing back up discs and after about an hour it comes up with an error that caused installation to fail and to contact the software manufacturer, tried again and the same happened. Tried apple hardware test and test results say no trouble found so am trying the extended test .any help would be great, thanks,Andy.

Try resetting the smc and pram.
To reset the smc
Shut down the computer.
Unplug the computer's power cord.
Wait fifteen seconds.
Attach the computer's power cord.
Wait five seconds, then press the power button to turn on the computer.
To reset pram
Shut down the computer.
Locate the following keys on the keyboard: Command, Option, P, and R. You will need to hold these keys down simultaneously in step 4.
Turn on the computer.
Press and hold the Command-Option-P-R keys. You must press this key combination before the gray screen appears.
Hold the keys down until the computer restarts and you hear the startup sound for the second time.
Release the keys.

Laptop wont start after shut down.

Hello, i got problem with HP Pavilion g6.
Yesterday i watched youtube, and laptop was on side, when i got too tired, then i shut down and left it on side for the night.In the morning i got home and thinked that battery is too low to start but when i plugged in power cable then the light even didnt turn on that's next to plug in hole. I have checked my power cable,it works fine but laptop dont do a single thing, even not the single light wont work.
Sorry for bad English,and its hard to write with phone.
Thank you.

Hello Uku,
Welcome back to the HP Forums!
I understand your HP Pavilion G6 notebook does not turn on. If the light around the power connector on the notebook does not light up, either the connector is not functioning or is not getting power from the adapter. If the LED indicator on the adapter is lit, it's a good sign that the adapter is functional, but is not a 100% fool-proof way to determine if it is working.
If possible, try another power adapter. Any adapter that fits will work for testing purposes. Once you have determined if the adapter works or not, discontinue use immediately and replace the original adapter if an alternate adapter works. You can order parts here: HP Part Surfer. You will need the exact model or product number to use this website. For information on finding your product and model numbers click here: How Do I Find My Model Number or Product Number?
You may also want to try reconnecting the power connector inside the notebook. For steps on removing and re-seating the power connector you can check out our Maintenance and Service Guide. The steps you're looking for can be found on page 63. Simply remove and reconnect the power connector and see if that resolves the issue.
If the above suggestions do not resolve the issue, I recommend you contact phone support for available service options. You can contact HP Technical Support at 1-800-474-6836 in North America. For all other regions click here.
Hopefully this helps!
Please click the "Kudos, Thumbs Up" at the bottom of this post if you want to say "Thanks" for helping!
Please click "Accept as Solution" if you feel my post solved your issue, it will help others find the solution.
The Great Deku Tree
I work on behalf of HP.

Help please PC wont start after i combined double sided and singlesided RAM

Can anyone help me please. I have a neo2 platinum board and 3200+ cpu. i used to have 2 X 512MB(double sided) ddr400 Ram PH brand. When i bought and added NCP brand 2 X 512MB(single sided) my PC wont start anymore. It just powers up for 1/2 a second then dies. I tried putting back my old RAM and resetting the BIOS but it still wont start.

thanks everyone i have isolated the problem...the culprit is the psu i have another problem though, after i bought a new psu, the vga card is not detected from time to time...i also get the BSOD upon exiting windows and I cannot access the BIOS, it just freezes after I press the DEL key.

Laptop Wont Start After Trying Fan Replacement

Hi All i have a G6-1371sa Laptop and i have tried to replce the on borad fan as its making a noise since putting it back together again it now wont turn on fromn the power button i have tried the 30 second test and still no change
Lee Sands

the laptop dose boot using Ctrl Alt Del and f5
Lee Sands

5800 wont start up with memorycard inside the phon...

Hi
My 5800 wont start with the memory card inside the phone. When the card is in the phone it just hangs with a white screen displaying the word NOKIA. When the card is removed the phone can be powered on and off without any issues. Any ideas?
thanks

is the card compatible ?it could also be a corrupt memory card. you can either try to reformat it via computer using the mass memory mode via usb and also store your data on the computer. try another card and see if the same thing happens. you might not be able to format the memory card you currently use, but if you are lucky enough you might be able. if you do indeed suceed you can try that card in the phone and see how that works.
If i have helped at all a click on the white star below would be nice thanks.
Now using the Lumia 1520

Laptop wont start

My laptop wont start, when I press power, the little light lit but then it died and there's nothing on the screen. I tried taking off the battery for 5 min and put it back on press the power for 30 sec but it still wont start please help... !

Same problem here, I have a dv6 that I used throughout the day just fine. I installed the windows 10 update, it proceeded to restart but never came back on. I tried taking out the batterie, unplugging it, and holding the power button to hard reset still nothing.

My System wont start after setting FSB to 200

My System wont start after I'd set my FSB to 200,
when the system starts, nothing comes up, and my Pc screen LED just blinks,
I have tryed to reseting the Bios but it doesn't help, have also tryed with new RAM and new Graphiccard but it doesnt help.
Please help me:-(
Am I resetting the Bios wrong? I set the jumper to safe mode and 100mhz, then I use the jumper to clear the CMOS. And the restart at set the jumpers back
3ghz AMD BARTON
NVIDIA nforce2 k7bn2 Delta
512 DDR RAM PCI3200
300WATT

Quote
Originally posted by roobster
set the multiplier lower , FSB(200) X multiplier (ex.10.5) = 2100 MHz , and your voltage raise it a bit too let say 1,700 ( default is 1.650 ) If this doesn't work at once , keep booting . My rig started up after 5 times . Strange but true .
does not work if he has a 3000.
they are multiplier locked.

Intel imac wont start after changing permission

intel imac wont start after i changed my hard drive permission to let me read and write, then i clicked apply to all enclosed files.i turned it off no problem. then it never started up again in os x. the grey screen with apple logo appears,then after a minute it restarts, and will keep doing that if i let it. i can start up in windows xp, but i dont know how to do anything in windows xp that will affect os x. i can use the hard drive in target mode, but i cant figure out how that can help me. i use a macbook to view target disk. ive spent hours looking through help and support. finally i do not have the os install disks. PLEASE HELP!

My apologies for the inept instructions.
Restart normally. Open Terminal in the Utilities folder. Paste the commands in the Terminal application to avoid typos:
sudo su
Press RETURN. Enter your admin password when prompted. It will not be echoed to the screen. Press RETURN again. Now paste each of the following at the prompt and press RETURN after each.
chown root:admin /Applications
chmod 0775 /Applications
chown root:admin /Library
chmod 1775 /Library
chown root:admin /System
chmod 0775 /System
chown root:admin /Users
chmod 0775 /Users
chmod -R -N /Applications
chown -R :admin /Applications/*
Again, my apologies.

Portege Z930-118 wont start after BIOS update

my PORTG Z930-118 failover and wont start after i upgrading in middle of upgrade i remove power and press shutdown bottom after that i see the power and wireless but screen still black ?
Any help please

Hmmmm.... BIOS upgrade interruption has screwed up BIOS and thats the reason why your notebook doesn't start properly. BIOS is damaged now.
In such case you need professional help by authorized Toshiba service provider.
On this forum you can find many threads about similar problems. Some people have tried to fix this alone and if you are interested to read how one other forum user has fixed it check please this thread.
Ayway, you can contact nearest Toshiba service, explain the situation and ask for help.

770-G45 wont start after ShutDown

Recently installed MSI 770-G45, problem starts when i regulary shutdown comp. from WinXP or Win7 64-bit.Computer wont start after that, like ther is no power, fans dont spin, no bips, NOTHING. I got to unplug power cord and plugg it again into psu, after that it starts normaly.
Strange thing is that computer starts normally when i manualy shutdown system(holding the power button on the case).There is no exception, starts perfectly evry time after manual shutdown, no need to unplugg powercord.
Rest of my components> Phenom II X2 555BE, Kingston 2GB 1333mhz, Sapphire 5770, HDD WD 250gb,PSU Corsair TX 650w.
Tried to change power cord, tried other PSU, other case (tought its maybe power button but no), changed mobo battery, installed several OS versions (XP, Win7) and still dont have solution.
MS 7599 ver. 2.0
Bios version 10.2
MoBo is new bought it 3 days ago.
PLEASE HELP!!!!!

First: It is important to clear CMOS after a BIOS update. Unplug power cable before the clearing, as there can be no power in the system
Second: Rebuild the system, but outside the case. Use only PSU, motherboard, processor, one stick of memory and graphics card. If it works better then, you may have a short, from a stand-off too many, or poorly isolated wire somewhere.
But I second it sounds like a motherboard problem. You'd better contact the one who sold it to you.
Oh, an oldie thing! You will need to install Windows again, with the new motherboard and all.

Safari wont start after i installed avi player any suggestions?

safari wont start after i installed a avi player any suggestions?

You may have installed the "VSearch" trojan. Remove it as follows.
Malware is always changing to get around the defenses against it. These instructions are valid as of now, as far as I know. They won't necessarily be valid in the future. Anyone finding this comment a few days or more after it was posted should look for more recent discussions or start a new one.
Back up all data before proceeding.
Step 1
From the Safari menu bar, select
          Safari ▹ Preferences... ▹ Extensions
Uninstall any extensions you don't know you need, including any that have the word "Spigot," "Trovi," or "Conduit" in the description. If in doubt, uninstall all extensions. Do the equivalent for the Firefox and Chrome browsers, if you use either of those.
Reset the home page and default search engine in all the browsers, if it was changed.
Step 2
Triple-click anywhere in the line below on this page to select it:
/Library/LaunchAgents/com.vsearch.agent.plist
Right-click or control-click the line and select
          Services ▹ Reveal in Finder (or just Reveal)
from the contextual menu.* A folder should open with an item named "com.vsearch.agent.plist" selected. Drag the selected item to the Trash. You may be prompted for your administrator login password.
Repeat with each of these lines:
/Library/LaunchDaemons/com.vsearch.daemon.plist
/Library/LaunchDaemons/com.vsearch.helper.plist
Restart the computer and empty the Trash. Then delete the following items in the same way:
/Library/Application Support/VSearch
/System/Library/Frameworks/VSearch.framework
~/Library/Internet Plug-Ins/ConduitNPAPIPlugin.plugin
Some of these items may be absent, in which case you'll get a message that the file can't be found. Skip that item and go on to the next one.
The problem may have started when you downloaded and ran an application called "MPlayerX." That's the name of a legitimate free movie player, but the name is also used fraudulently to distribute VSearch. If there is an item with that name in the Applications folder, delete it, and if you wish, replace it with the genuine article from mplayerx.org.
This trojan is often found on illegal websites that traffic in pirated content such as movies. If you, or anyone else who uses the computer, visit such sites and follow prompts to install software, you can expect more of the same, and worse, to follow.
You may be wondering why you didn't get a warning from Gatekeeper about installing software from an unknown developer, as you should have. The reason is that the Internet criminal behind VSearch has a codesigning certificate issued by Apple, which causes Gatekeeper to give the installer a pass. Apple could revoke the certificate, but as of this writing has not done so, even though it's aware of the problem. This failure of oversight has compromised both Gatekeeper and the Developer ID program. You can't rely on Gatekeeper alone to protect you from harmful software.
*If you don't see the contextual menu item, copy the selected text to the Clipboard by pressing the key combination command-C. In the Finder, select
          Go ▹ Go to Folder...
from the menu bar and paste into the box that opens by pressing command-V. You won't see what you pasted because a line break is included. Press return.

XP Machine wont start after 8310 Software install

Sorry if this has been covered before - but I installed the desktop software that came with my BB 8310 Curve and now my system wont start. It gets to the Window Splash screen (the windows logo and the bar accross the bottom that runs accross the screen) and then resets. This happens in regular startup, last Known good config, safe mode with network, safe mode. Windows will not load.
Windows XP
SP2
2 Gig ram
500 Gig HD
(powerfull machine - expect softare corrupted registry)
Any suggestions before I do a rerinstall of windws to get machine to load OS
Many thanks
-John-

Do you know what version it was you installed?
I would start with a clean uninstall of that Desktop Manager software (that is what you installed?). See this link for instructions:
http://www.blackberryforums.com/rim-software/25937-how-perform-clean-uninstall-reinstall-blackberry-...
Then, I would recommend downloading and installing Desktop Manager verions 4.6 from here:
https://www.blackberry.com/Downloads/entry.do?code=A8BAA56554F96369AB93E4F3BB068C22
Persoanlly, I would recommend the version you find there withOUT the Media Manager software.
1. If any post helps you please click the below the post(s) that helped you.
2. Please resolve your thread by marking the post "Solution?" which solved it for you!
3. Install free BlackBerry Protect today for backups of contacts and data.
4. Guide to Unlocking your BlackBerry & Unlock Codes
Join our BBM Channels (Beta)
BlackBerry Support Forums Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

SSMS wont start after Installing SQLServer

Hello,
After SSMS wont start after updating VS2012. I have unistallled and installed a number of times but the error message I keep getting indicates that Visual Studio shell Isolated is missing. I have tried to install this directly from the set up dvd but
no success.
Also I noticed that VSShell is missing in the C:\Program Files (x86)\Microsoft SQL Server\120\Tools\Binn.
I am assuming that this has something to do with it.
Can someone please tell me how to fix this?
Thank you.
here is the error message received

Hi,
Try the below solution and see how it works.
Note: Take a backup of the key before make any changes on the registry keys.
http://support.microsoft.com/kb/322756
Start regedit.exe
Go to HKEY_CURRENT_USER\Software\Microsoft\SQL Server Management Studio
Delete 12.0_Config
Restart ssms.exe
Here is the original thread:
http://social.msdn.microsoft.com/Forums/sqlserver/en-US/aeff13b3-3960-4724-bb9a-7e585651d7f4/sql-server-2012-error
Thanks.
Tracy Cai
TechNet Community Support

HELP!!! my laptop wont start after water went inside the key board

Similar Messages

Maybe you are looking for