HELP!!! Need HP Z1 LCD bezel part number and replacement cost

Was wondering if anyone had a part number and price for the LCD bezel for HP Z1. Mine is cracked while moving and can't seem to find a number... Called HP four times and been routed around three of those times, until one person finally said, it is the same as the LCD panel.. Hard to be believe it is not sold seperately. Thanks!!!

Hi,
Please try the following store:
http://h20141.www2.hp.com/Hpparts/Default.aspx?mscssid=C6565EF7171540FF908F121D766CF8CD
You can also find part # on the 8th manual of the following link:
http://h10025.www1.hp.com/ewfrf/wc/manualCategory?cc=us&lc=en&dlc=en&document=&product=4036210
which say : The United Kingdom 517863-031 on page 3-3.
Regards.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

Similar Messages

Twist LCD panel part number

How can I know the LCD panel part number of Twist (Lenov Twist 3347 4HU)?
Do you have any idea?

there are several, apple buys the displays from more than one vendor, is my understanding.
if you need a display panel, ifixit.com & powerbookmedic.com both have them.

Adobe Premire Elements 13 purchase wouldn't download. No support no help no phone mnubers. Found a number and was on hold for over 25 minutes. need help need a number to call.

Adobe Premire Elements 13 purchase wouldn't download. No support no help no phone mnubers. Found a number and was on hold for over 25 minutes. need help need a number to call.

Downloadable installation files available:
Suites and Programs: CC 2014 | CC | CS6 | CS5.5 | CS5 | CS4, CS4 Web Standard | CS3
Acrobat: XI, X | 9,8 | 9 standard
Premiere Elements: 13 | 12 | 11, 10 | 9, 8, 7 win | 8 mac | 7 mac
Photoshop Elements: 13 |12 | 11, 10 | 9,8,7 win | 8 mac | 7 mac
Lightroom: 5.7.1| 5 | 4 | 3
Captivate: 8 | 7 | 6 | 5.5, 5 | 1
Contribute: CS5 | CS4, CS3 | 3,2
FrameMaker: 12, 11, 10, 9, 8, 7.2
Download and installation help for Adobe links
Download and installation help for Prodesigntools links are listed on most linked pages. They are critical; especially steps 1, 2 and 3. If you click a link that does not have those steps listed, open a second window using the Lightroom 3 link to see those 'Important Instructions'.

Report to find a material by a mfr part number and old material number

Hi,
Is there any standard report to find a material by a mfr part number and old material number ?
For the moment, we are using MM03 to search articles by these selection criterion.
Thanks,
Julien Girard

Hi
As there is no stsndard report use the SQVI to find out the details, It is very simple , please follwo the below steps.
Use Txn SQVI, enter the Quick view field say- ZMNFR and click the create button, Enter the title in the next screen i.e Report name- Say - Manufacturer's Part No. Details, in the same screen you need to enter MARA for the data from table/database view, please leave the 1. data source as Table only and the radio button as Basis mode only. Click the tick mark , you will go to the next screen,
You will notice Quick viewer Intial screen
Open the node general material data
Select the Buttons besides the fields MARA-MATNR for material number, MARA-MFRPN for manufacturers part number, and MARA-BISMT for old material number. You can include any other field if you wish to have in your output. You will notice two check boxes against each field, one is for input screen field and the other is for outputf field. But currently you do not bother about and select both the check boxes or any other field you wish to have as input and output as well. Once selected all the fields afer clicking the check boxes save the total arrangement. and then in the same screen use the execute button or use F8 to find out your report input screen.
Now enter the Material number for which you wish to know other two details in the report and execute again you will find the report output.
Please ensure that you are maintaining both the details in material master basic data1 and purchasing view if you wish to get out output
Best regards
SAM
Edited by: samuel mendis on Apr 8, 2009 6:52 AM

Part number and serial number appear to be weird after memory installation

How come the part number and serial number are all 0.
eg: part number: 0x00000000000000000000000000
serial number: 0x0000000
however, the RAM just work fine. Do I have to contact the vendor. this is my first time so I just want to check it out is there any problems.
Thank
Minh
Message was edited by: chuminh

Anybody helps??

I forgot the apple id and email password also the answer to the security question but i have the Serial, part number and imei

i forgot the apple id and email password also the answer to the security question but i have the Serial, part number and imei

Apple ID security issues -
Account security issues almost always require you to speak directly to an Apple representative to securely establish your identity as the account holder. You can set it up so that Apple calls you, either immediately or at a time convenient to you.
1. Go to www.apple.com/support
2. Choose Contact Support and click Contact Us
3. Choose Other Apple ID Topics and choose the appropriate topic for your issue
4. Follow the onscreen instructions

I need the Lotes (or HP) PCI-e edge connector part number to replace it on a H8-1360t

The PCI-e graphics processor in my H8-1360t was pulled without releasing the tab on the edge connector first. As a result, the plastic connector pulled free of the fingers. The PC is long out of warranty and this would not be covered by warranty anyway.
This leaves the PC inoperable as the plastic housing cannot be pushed back on to the fingers. So the motherboard will have to be removed and the PCI-e edge connector replaced.
The connector is made by Lotes, but has no part number on it. I need a part number in order to obtain a replacement. As far as I know, there is no part-specific tech manual for the motherboard that I could refer to for this information. It would have to come from someone at HP.
Help.
This question was solved.
View Solution.

A difficult search for the part.
http://www.ttiinc.com/object/fp_fci_pci.html http://www.farnell.com/datasheets/188358.pdf
I am a volunteer. I am not an HP employee.
To say THANK YOU, press the "thumbs up symbol" to render a KUDO. Please click Accept as Solution, if your problem is solved. You can render both Solution and KUDO.
The Law of Effect states that positive reinforcement increases the probability of a behavior being repeated. (B.F.Skinner). You toss me KUDO and/or Solution, and I perform better.
(2) HP DV7t i7 3160QM 2.3Ghz 8GB
HP m9200t E8400,Win7 Pro 32 bit. 4GB RAM, ASUS 550Ti 2GB, Rosewill 630W. 1T HD SATA 3Gb/s
Custom Asus P8P67, I7-2600k, 16GB RAM, WIN7 Pro 64bit, EVGA GTX660 2GB, 750W OCZ, 1T HD SATA 6Gb/s
Custom Asus P8Z77, I7-3770k, 16GB RAM, WIN7 Pro 64bit, EVGA GTX670 2GB, 750W OCZ, 1T HD SATA 6Gb/s
Both Customs use Rosewill Blackhawk case.
Printer -- HP OfficeJet Pro 8600 Plus

MacBook LCD screen part number

Hi there,
I just gave up trying finding the part number of the LCD screen of a MacBook. I have searched all over this site and gone thru pages and pages of this discussion forum. Have tried narrowing down my search using the search field + search tips to no avail. I don't have the computer with me so I can't dissasemble it in order to get the part number.
Would anybody know what the part number is?. I believe they only come in 13" size.
Thanks very much in advance.
Cheers,
Victor
Message was edited by: vpombo

there are several, apple buys the displays from more than one vendor, is my understanding.
if you need a display panel, ifixit.com & powerbookmedic.com both have them.

I need to know what the part number is for a replacment hard drive chasis - 8460p

I need to order a replacment chassis that the hard drive screws into for the 8460p, does anybody know the part number for this piece?

Hi:
You are going to have to contact HP for that--1-800-334-5144.
The only parts listed in the service manual are for the actual hard drives.
Paul

Qosmio X300-11W: Need an CD/DVD-RW Part Number?

Hi all,
I am currently refurbishing a X300-11W and I need to know the optical drive part number to find a replacement.
Any ideas? Or know where I can buy a cheap replacement in the uk?
Thanks!

Hi
As far as I know you can find an list of compatible ODDs in the Qosmio X300 user manual.
Did you check it?
Furthermore you can order all compatible parts from an Toshiba ASP (authorized service provider) available in your country.

MacBook Pro 15.4" 2.16GHz A1150 LCD Manufacturers Part number

Hi there. Can anyone in the know tell me what the manufacturers part number is for this laptop? I'm aware there are 2 possible, a CHIMEI and a Samsung I think.
I know it can be found by going to the system prefs>colour but I don't have access to the laptop.
Many thanks,
DeBaron

Low battery life and high temperature immediately suggests to me that some daemon or other background process is probably running at almost 100% CPU utilization in some tightly rolled loop (read "hung").
Battery life on modern laptops is dependent on how heavily the CPU is being utilized. A single app or daemon running amok like that can eat battery life rather rapidly. And, of course, CPU temperature is also proportional to use, so you can basically think of battery life and operating temperature as inversely proportional.
To find out what process is misbehaving, run Terminal. Type "top -o cpu" and press return. See if there's some process running at 99% or whatever, then get back to us.
You might try installing the combo update. If the problem is caused by a installer glitch, that should fix it right up. If it's a bug, obviously that won't help. I couldn't begin to guess which it is.

I need a new LCD bezel for W520. Which FRUs to get?

Hello,
today I've broken the LCD bezel on my W520 and I'm looking for a new one.
And I'd like to make sure I understand these FRU's correctly:
60Y5482: LCD bezel itself.
04W1585: Screw kit. Does it contain those 3 square screw covers that are on the LCD bezel? Or are they included in a Tape kit 04W1586?
04W1566: Clear plate. This should be that wide sticker with 3 icons, Lenovo logo and a W520 text, right? But I see only this FRU for both T520 and W520; so how do I make sure I get the correct W520 one?
Thanks a lot.

The clear plate kit will contain both T520 and W520. As far as the screw kit, most have the stickers but some don't. I don't know about T520, but the old ones can be reused if you are careful when removig them from the old bezel. I suggest the tip of a razor knife.

Need part number to replace primary internal battery

Hi, I have been receiving Error Code 601 stating my primary internal battery storage capacity is very low. I am trying to find the correct replacement part number. I have been searching the site but am not confident I have the correct part number. My laptop is critical to my job and I must order a replacement ASAP. I appreciate the guidance!

This is a slightly misleading error message as it does in fact refer to your notebooks main battery, not the cmos battery. The reason it is call an internal battery is to distinguish it from the extended batteries that you can purchase with some models that attach to the outside of the laptop. Your battery should have a label with P/N.

T400 case number and replacement part?

I have a clients T400 that has come out of warranty. His 160GB HD died. I called Lenovo first to make sure the machine was out of warranty, the tech advise me that is way and gave me the HD FRU number and the phone number to call to get a replacement.
My colleague called IBM and gave them the part number, they said the FRU doesn't exsist and got us the correct part number but said unless we had a case number from Lenovo the drive would be sold AS-IS. So if we bought it and for someone reason it didn't work they would not warranty or exchange the drive.
So my colleague called Lenovo back who said "We don't give case numbers out for machines out of warranty". It seems that IBM thinks differently. Lenovo also said there some way of creating a case on their website which will send me an email with the correct replacement part number...do you think I could find what they are talking about??? NO!
Has anyone had to deal this mayhem? It's like the left hand doesn't know what the right hand is doing....Plus it makes not sense to not properly help people who have OOW machines that are still fairly new.
I have thought of maybe getting the one of the big bosses at IBM on the phone to fight it out with the boss at Lenovo!
Andrew
Xbase Technologies Corp.

hey xbasetech,
could you pm to me the following and i will see what i can do for you :
Name:
Country:
Mobile:
Email:
MTM [machine type model]:
(To locate MTM - http://support.lenovo.com/en_US/FindProductNumber.page#find)
S/N:
Date of Purchase:
Case/Order Number : (if any)
Screenshot of Error(if applicable) : (upload it to a hosting site and paste the link here)
Location of unit : Home / Repair Center (delete where appropriate)
Description of issue :
WW Social Media
Important Note: If you need help, post your question in the forum, and include your system type, model number and OS. Do not post your serial number.
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"!
Follow @LenovoForums on Twitter!
Have you checked out the Community Knowledgebase yet?!
How to send a private message? --> Check out this article.

WDS Set up - Help Needed! Airport Extreme with one Relay and one remote

Hi Guys,
I need a bit of help. I am feeling quite stupid and frustrated. I am having some difficulty with setting up a WDS network with:
Base station: Airport extreme (current version)
Relay: Airport Express (current version)
Remote: Airport Express (current version)
I start by cold resetting the three units. The Base station is connected via Ethernet. The setup I wish to get going is a simple base - relay - remote.
I go through the utility manager and set up the base station, first as "create a wireless network" enter the ISP details etc etc. Its green light. Everything is fine. Then manually configure the Base Station. Hold down option key hit Participate in a WDS. I then select main enter + and add the Mac Id's for the intended Relay unit and Remote Unit (12 character and numeric string). At this stage I am only adding the intended Relay unit and Remote units MAC number.
Question 1: Do I need to add the base unit's MAC number itself under: WDS Remotes? even I am setting it up as Main?
I am careful to note the security settings and the the Wireless Network name to match these in the relay and remote set up. Under the Wireless tab I leave the Radio Mode: as Automatic (802.11a/n - 802.11b/g/n). I make sure the base has "allow this network to be extended" ticked. Under Radio Channel selection I edit it to reference channel 1 for 2.4Ghz (5 Ghz leave as Auto). I am careful when setting up the Relay and remote to match the Radio Channel. (Although I tired many channels as I thought maybe interference was a factor and denying the fact its obviously my set up skills as a factor).
Question 2: Do you need to disable Guest networks? I would think it does not matter as I have tired turning it off and has not made any difference.
Under Access Control I leave as default, Not enabled.
Next I hit update and and error message comes up. WDS Error as it can not find other units. Ok fine as the relay and remote are not yet set up. So I ignore and can get to the stage where the base unit is working and green light with an internet connection.
I then proceed to set up the Relay unit. Doing the same steps as above with a couple of differences being I add the MAC numbers and select the WDS Mode (Relay for Relay and Remote for Remote. I add the Main base station (i.e Airpot Extreme MAC No.) when prompted and then + the Remotes MAC number. The same for the Remote except I only need to add the base station's main no.
Question 3. Do I need to add the Relay's own MAC number to its own setup? This seems doubtful as with the base station but tired with and without for good measure with no success.
The 2.4Ghz channels are all set to 1. Radio mode set to Auto. Although even when I try to manually set them to all identical it doesn't seem t help.
Then the problems begin. The base unit is Green and the Relay and Remote say they are not connected to the internet. I assume since I have not seen a WDS Error message then the units are set up correctly or as I ignored it on the base unit. But when click unignore the error seems to work itself out.
Question 4. I need help to understand why I have no internet. The remote / relay says something about no IP number and I don't really understand what I should do? Do I need to go back the Airport Utility Manager and start messing about with the TCP/IP, DHCP, NAT ? The base is set up PPPoE and the relay and remote are set to Bridge.
It is really puzzling me why the relay and remote flash amber with error messages related to the IP number? I have tried turning off the base station and router and then on again but no joy.
Can anyone please enlighten me or give me a few ideas? I am doing something very obviously stupid and I guess the fix is something simple that I have overlooked.
I did spend the time and go through the threads and search online, So I am not trying to waste anyone's time I referenced the two links to get a second opinion:
http://broadcast.oreilly.com/2009/03/taming-an-airport-express-wds.html
http://www.macobserver.com/tmo/article/settingup_an_airport_relay_with_airportexpress/
Any help much appreciated!

Versed wrote:
I need a bit of help.
Welcome to Apple's discussion groups.
My WDS experience is limited to "main" and "remote" configurations (no "relay"), so I'm not posting from direct experience, but below is what I think would work in your case.
I go through the utility manager and set up the base station, first as "create a wireless network" enter the ISP details etc etc. Its green light. Everything is fine. Then manually configure the Base Station. Hold down option key hit Participate in a WDS. I then select main enter + and add the Mac Id's for the intended Relay unit and Remote Unit
I don't think the "main" unit needs to be told about the "remote" unit, only about the "relay" unit.
Question 1: Do I need to add the base unit's MAC number itself under: WDS Remotes? even I am setting it up as Main?
You'd never enter the MAC address of a unit into its own configuration, if that's what you mean. I also don't think that you'd need to enter the MAC address of the main into the remote and conversely.
I am careful to note the security settings and the the Wireless Network name to match these in the relay and remote set up. Under the Wireless tab I leave the Radio Mode: as Automatic (802.11a/n - 802.11b/g/n).
Five things have to match in a WDS configuration: network name, encryption type, network password, band, and channel.
I make sure the base has "allow this network to be extended" ticked.
I don't think that's important for a WDS configuration.
Question 2: Do you need to disable Guest networks?
I wouldn't think that matters.
Under Access Control I leave as default, Not enabled.
That's fine.
WDS Error as it can not find other units. Ok fine as the relay and remote are not yet set up.
Right.
I then proceed to set up the Relay unit. Doing the same steps as above with a couple of differences being I add the MAC numbers and select the WDS Mode (Relay for Relay and Remote for Remote. I add the Main base station (i.e Airport Extreme MAC No.) when prompted and then + the Remotes MAC number. The same for the Remote except I only need to add the base station's main no.
I think this should be the MAC address of the relay station, not that of the main station.
Question 3. Do I need to add the Relay's own MAC number to its own setup?
No.

HELP!!! Need HP Z1 LCD bezel part number and replacement cost

Similar Messages

Maybe you are looking for