Help Needed - Remote Disk Access via MobileMe for AEBS

OK, I've done a lot of reading in this forum, but didn't find a resolution to my problem.
Here are my configuration:
1) ADSL Router(2Wire 2700HGV-2) in bridged mode
2) Airport Extreme Base Station (Simultaneous Dualband) with 7.4.1 firmware acting as the router using PPPOE
3) External USB disk formatted using Mac OS format attached to AEBS
Working:
1) Within the LAN, can access the disk without any problem
2) Over the WAN, Back to my Mac works fine for all my Mac computers
Not Working:
Over the WAN, I can see the AEBS in the shared section, however, upon clicking it, it always tells me that the connection failed after about 30 seconds, even when I try to use "connecting as".
Anyone has tried this feature and it worked? Really appreciate if you can help as I am going to be on trip soon and I wish to access the disk from Internet when I am over there.
Thank you!

Hi rekeno
Thanks for your post. I have the exact some problem. I'm sitting at work with my MacBook. At home there's my Airport Extreme and a Mac Pro.
I can see both in my "Shared" section AND they also have different IPv6 tunnel addresses:
[15:07 root@pm1] ping6 macpro.XXX.members.mac.com
PING6(56=4088 bytes) fd22:3569:a8da:4c12:217:f2ff:fed4:6de0 --> fd44:bbdd:fce3:3be9:21d:4fff:fe4b:b80
16 bytes from fd44:bbdd:fce3:3be9:21d:4fff:fe4b:b80, icmp_seq=0 hlim=64 time=54.748 ms
Works.
[15:14 root@pm1] ping6 airport.XXX.members.mac.com
PING6(56=4088 bytes) fd22:3569:a8da:4c12:217:f2ff:fed4:6de0 --> fdfe:d7a4:759a:a360:21b:63ff:fef5:30a2
^C
--- airport.XXX.members.mac.com ping6 statistics ---
3 packets transmitted, 0 packets received, 100% packet loss
This times out.
Interestingly I can use Screen Sharing to my MacPro and do the same:
[15:17 mau@macpro] ping6 airport.XXX.members.mac.com
PING6(56=4088 bytes) fd44:bbdd:fce3:3be9:21d:4fff:fe4b:b80 --> fdfe:d7a4:759a:a360:21b:63ff:fef5:30a2
16 bytes from fdfe:d7a4:759a:a360:21b:63ff:fef5:30a2, icmp_seq=2 hlim=64 time=0.721 ms
This works AND it uses the SAME IPv6 address.
I have also checked that my IPv6 tunnel configuration is allowed in the Airport Utility.
Do you see the same behaviour? Can you run the same commands?
Thanks a lot!
Patrick

Similar Messages

Application And Gaming / Port Forwarding || HELP NEEDED || Can Only Access Via LAN

Hi.
I have just bought a Wireless Router, Model Number: WGKPC354G-UK. With the intention of setting up a small server. This server will run from my PC (directly wired into router), running a game called "Counter Strike" - I had to download a dedicated-server tool for this and i successfuly installed this and followed the tutorial to set it all up..
So I thought i had done it, but I could only access my server with my internal IP 192.168.1.64 (LAN).
I then found out that i needed to "Port-Forward" I followed a tutorial on www.portforward.com - This showed me how to open the ports, and which ones to open.
I did all this and i still encounter the same problem !
So i then opened all my router ports "DNZ" and it still doesnt work !!!
Any help will be greatly aprreciated !
PS. Below Are The Required Ports.
http://portforward.com/english/routers/port_forwarding/Linksys/WAG354G/Counter_Strike.htm

Keep in mind your ISP could be blocking the ports needed. DMZ almost ALWAYS works and if it doesnt, most likely your ISP blocks the ports.
another test is to make sure you can connect to the game server from another CS machine on the inside of your network. If this works, that means your server is up and running properly and its probably your ISP blocking certain ports needed for the CS Server.
You should also check you have the Windows firewall disabled, and any other software firewall on your server disabled.

Remote TC access via port forwarding

I have been trying to setup my network for remote TC access via port forwarding. Here's my setup:
Verizon FiOS router (main router, dhcp & nat) -> connected to TC set in bridge mode with a static IP
I can remotely access the TC using Back to my Mac with no problems, and of course locally on the home network via Wifi.
Since the TC has to connect in bridge mode, port forwarding is done on the FiOS router.
If I set a port forwarding rule in the FiOS router TCP,UDP (any) to port 548, it works. However I want to use a specific connection port
so others can't connect unless they know the forwarded port. BTW, I have remote disk sharing set with Use Device Password.
So here's what works:
FiOS Router (TCP any -> 548, UDP any ->548)
What doesn't work:
FiOS router (TCP 8990 -> 548, UDP 8990 -> 548).
Is there any additional setting required for specific port forwarding to work?

You're my hero!
I also have my TC in Bridge Mode to my Verizon FIOS Router. I used to be able to access my TC remotely, but since I upgraded my router (MI424WR GigE), I had forgotten some port forwarding rules I must have established in my old router. Once I re-created these two port forwarding rules (just like yours), I can remote access my TC (with TC password) again.
In addition, I have a static host name aliased to my dynamic IP address through dyndns.org (I have the free version, which I don't think is available anymore, but there are other free providers out there) for easier remote access.
Regarding, Secure Share Disks: with TC password vs a disk password. Is one more secure than the other?
Thanks!

Internet access via hairpinning for Spoke to Hub IPSec VPN

I have a hub and spoke configuration with a number of site-to-site IPsec VPNs from 857's terminating on an 1811 at the hub. Also in the mix is a client-to-site (EZVPN) which also terminates at the hub.
I need to ensure all traffic destined for the internet goes out through the hub 1811. I've looked at trying to use a form of hairpinning so that "interesting traffic" from remote sites gets NATted at the hub router to the internet.
I have seen a number of configurations (in these forums) where internet-directed traffic from EZVPN clients is forced via a hairpin out via the hub router. I am trying to emulate that feature with the site-to-site IPSec VPNs - where internet directed traffic from spokes must go through the hub router, and not be permitted to go directly to the internet from the spoke routers.
Attached are configs for the hub router and one of the spoke routers, and a pdf diagram.
I can get traffic to the internet (in my test lab) from the lookback connector (1.1.1.1) by extended command pings, I have connectivity from the spoke1 lan to the hub lan (pings again); but not from the spoke1 lan to the internet via the hub router.
Thanks in advance for any help
Phil

Thanks, guys. Yes, those two access lists did need some attention.
I've changed the access list on the spoke router from
access-list 120 permit ip 192.168.8.0 0.0.0.255 192.168.0.0 0.0.255.255
to
access-list 120 permit ip 192.168.8.0 0.0.0.255 any
which allows traffic from the spoke lan out to the internet via the hub router. I've also taken NAT off the spoke router.
But I also need to change the matching access list on the hub router. I changed the old access list from
access-list 121 permit ip 192.168.0.0 0.0.255.255 192.168.8.0 0.0.0.255
to
access-list 121 permit ip any 192.168.8.0 0.0.0.255
but I couldn't pass any traffic over the VPN. If I remove access-list 121 completely, then traffic does pass, but the crypto map on the hub router becomes "incomplete".
When the tunnel is up, and passing traffic, I can ping an internet address (in my lab), but not all traffic is getting through. Every second ping times out, often there are 3 or 4 pings that time out.
Any suggestions as to what to do with the access list (121) on the hub router, and what can I do to get more reliable results (i.e. get every ping to work)?
TIA
Phil

Low Network Utilization in Remote Disk Backup via SAP FTP

Hi gurus,
I'm running whole online backup + redo log to backup my SAP server to backup server via SAPFTP (remote disk backup).
I'm using 100Mbps network connection between the two servers, with SAP server configured to 'maximize data throughput for network application'.
When I copy data from SAP Server to backup server manually, the speed is OK (around 98% network utilization).
But when I use put command in program RSFTP002 (SAPFTP) for the same file, the network utilization is just around 10%.
I use Windows Server 2003 x64 for SAP Server, and Windows Server 2008 x64 for Backup Server.
Each has adequate RAM, 8GB for SAP Server and 4GB for Backup Server.
Is this technical problem or is it because backup is considered background process, thus lowering its speed?
Help will be very much appreciated.
Edited by: Bobby Gunawan on Jan 9, 2009 11:44 AM

go read http://help.sap.com/saphelp_45b/helpdata/en/0d/d311324a0c11d182b80000e829fbfe/frameset.htm
it's old but should help you nonetheless.
I would not use SAPFTP as you found out, it is slow.
use DD instead which is much faster.

Need to give access to users for report painter query without GR55

Hi,
I need to create a transaction code for a query created using report painter. We do not want to give access to user for GR55.
Please help us in achieveing this one or any other way to execute report without GR55 access.
Regds,
Servesh
Moderator: Please, search before posting - it has been answered several times

Hi,
You can create the transaction the same using SE93 transaction code.
Also see the below link for detailed rocess:-
[http://home4sap.com/Blog/2009/08/how-to-create-a-transaction-code-for-report-painter-reports/]
Regards,
Gaurav

Archived Invoices (on separate DB) need to be accessed via Oracle Apps

Hi there,
Our organization is currently on Apps 11.5.10.2 and have acquired a new company which has been moved onto Oracle. However this new company has lots of old invoices that we do not wish to migrate to Oracle as we wish to keep the Apps database lean and fast and this data is used very rarely.
Our plan is to move this data into a separate DB/ Warehouse and build a custom application (using Oracle Forms and Reports) to query the data and print reports.
However, we need to add some sort of link / menu item within Oracle Apps to call this new application when the user wishes to query this archived data.
Is this possible? If so, how can this be achieved? How do we create the link from Apps to another database?
Any help will be much appreciated?
TIA.
Ashika.

Duplicate post.
Archived Invoices to be accessed via Oracle Apps
Re: Archived Invoices to be accessed via Oracle Apps

Help needed with internet access

I have just aquired a 5800 and I (think) I have turned of the 3G so it will only connect via my home WiFi unless it asks me. However, when I do connect I get a tiny little symbol which looks like 3.5g and the book says it is something to do with "HSDPA". It tells you that a line under it means "supported and active" and that a line through it means "a connection is on hold" but doesn't tell you what if there are no lines, just the symbol and what the flaming hell that means anyway.
My question is - when this is showing, am I doing something that I am being charged for ? On this phone I do not want to do anything chargeable without first being asked, so if anyone understands this minefield of information I would be eternally grateful for your assistance.
Solved!
Go to Solution.

You can't normally switch off internet access via the network through settings, usually you get the following network options:
GSM only (which could could connect to the internet via GPRS)
UMTS only (this is 3G)
Dual mode (which selects 3G if the service is available in the area, otherwise defaults to GSM)
Your phone will always show the GSM or 3G signals if it is in range of such services, this does not mean that you are conencted to the internet by them. If you are connected via WLAN, you will not be charged for internet access over the internet.
One thing to be careful of is that if you leave the range of your WLAN router, the phone can automatically go for the next access available point in the "Destinations" setting, which could be your network. As long as you are in range of the router and it is working fine, you should have no worries.

Help needed Hard disk Problem

I am not very computer Savoy!. But every time I turn my laptop on it keeps freezing up on me and I get a massage that says I am having a Hard Disk Problem and that I should back up all my files before the computer crashes. And I would like to what I should do to fix this? I thought that I could reload my operating system but my computer did not come with that disk and I can't seem to find it here on this web site. Any idea's?

Without knowing specifically which model you have it's difficult to tell for sure, but most Toshiba's made in the past few years come with a Recovery Partition. You can invoke the Recovery Process by holding down the 0 (zero) key while turning the computer on and holding it down until the Recovery Process starts. You can also create a set of Recover Disks from the Recovery partiton by going to "Start - All Programs - Toshiba - Recovery - Recovery Disk Creator".
As for the error message about Hard Disk Problem, that could mean that the hard drive is starting to malfuncion and will soon stop functioning at all. You need to determince what brand of hard drive your's is, go to that companies support site, download their Diagnostic Program, install it, and run the most exhaustive test to determine if it is failing or not.
And please backup you important data as soon as humanly possible as there is a good chance you will lose it forever.
If you don't post your COMPLETE model number it's very difficult to assist you. Please try to post in complete sentences with punctuation, capitals, and correct spelling. Toshiba does NOT provide any direct support in these forums. All support is User to User in their spare time.

Help needed in developing web map service for mobile devices

please can any one help me(with source code if possible) for developing the web map service client for mobile devices in J2ME.

There are a couple of ways you could do this. Bluetooth communication is available on a few J2ME devices, so you could do it through that. Or you could set up a servlet on the J2SE app end and send the data over the internet (check out HttpConnection). I'm not sure of any other quick and easy methods.

How to: Setup AAE for Remote Disk Access & Serve PS3

Hi there,
I've read so many tutorials, and tried so many combinations, but haven't found anything for my specific purpose.
I was wondering if someone might have the insight to do a quick run-through (including specific settings) on how I would setup my Airport Extreme for the following scenario/purpose.
Setup:
1. Netgear DGN2000 ADSL Modem + Router in one
2. Airport Extreme = Model #A1354
3. Western Digital Studio 1TB (mac os extended journaled formatting - not used as time machine)
4. PS3 80gb
*To accomplish:*
1. Access the Western Digital HDD remotely. So I can access my files from work.
2. Use the Western Digital HDD to serve media to the PS3 when I'm at home, so I can watch movies without having my computer turned on.
Caveat:
1. I don't want to use/pay for MobileMe.
Many thanks,
Glen

Hello nelga. Welcome to the Apple Discussions!
Since most of your questions are not really AirPort networking related, I will do the best I can to provide assistance.
1. Access the Western Digital HDD remotely. So I can access my files from work.
I know you don't want to use BTMM, but to best understand the hurdles you will be up against, it might be worth taking a quick look at how BTMM works "behind the scenes" to allow you to access a HDD remotely.
BTMM - Basic Communication Flow
o For a computer connected to the Internet via a router, BTMM "asks" the router for its configuration information. For a router, like your AEBSn, that uses NAT-PMP, BTMM will ask the router to assign arbitrary public ports. In turn, the router will provide these port assignments (& the router's Public IP address) back to BTMM.
o BTMM then sends this information to the MobileMe account. In background MobileMe updates a special set of DNS entries to be used by BTMM. These entries are then made available to all BTMM clients using your MobileMe account. When a computer, with BTMM enabled, uses your MobileMe credentials, it automatically retrieves a list of all other computers/routers that are registered with the same account. All these devices should then appear under the SHARED section of the Finder.
o When attempting to connect to a remote computer (or router), BTMM creates a secure connection to that remote device using the information from the MobleMe account.
o Once the connection is established, the devices can then communicate with each other.
The key to all this is that you will need the following in order to be able to remotely access the HDD:
1) Your ISP must provide you with a publicly reachable IP address.
2) If your ISP provides you with a Dynamic (vs. a Static Pubic IP address), you will need to keep track of that IP address in order to consistently have access to the HDD. Without knowing this address, when your ISP changes it periodically, you will have to manually "retrieve" it to connect again. You can get around this by using a service, like DynDNS.
3) You will have to configure your NAT router for port forwarding/mapping to allow the necessary file sharing communication to pass through the router to the AEBSn with the shared HDD. Specifically you want to open the appropriate ports for both the AFP (TCP: 548) & SMB (TCP: 445) file sharing protocols.
4) Similarly you want the AEBSn to be enable for file sharing.
2. Use the Western Digital HDD to serve media to the PS3 when I'm at home, so I can watch movies without having my computer turned on.
In order to stream video from your WD HDD, you will need a DLNA-compliant Media Server to stream that data to the PS3, which is a DLNA client. With that said, you will need at least one computer (Mac, PC, or Linux-based device) running in order to run this server. The WD HDD has no means to run this server as it has no operating system.

Help needed to publish site via 1and1 instead of Mobileme

Hi - I'm far from a computer whiz, and am struggling to publish my iWeb site via 1and1 using my newly registered personal domain name... When I do the test connection on the iWeb page, it tells me sth is wrong, but I have no idea what!?!? The details I have on there are:
Server Address: ftp.1and1.com (don't know if this is correct though, or if this should be my personal domain name??? - 1and1 are the hosting site for me)
User name and password as per my details for 1and1
Directory/Path: www/ (don't know if this is right either, or how to find out??)
Protocol: FTP
When I click on Test connection - I get the message : Testing Failed. A connection to ftp.1and1.com couldn't be established. Verify your settings and try again. (I get the same thing if I change the server address to my domain name)
The Website URL is : http://hilaryschachtphotography.com
Can anyone help please?? :-))

Go to the source :
http://faq.1and1.com/websites/access/ftp/index.html
http://faq.1and1.com/webspace__access/ftpaccount/index.html
http://faq.1and1.com/webspace__access/ftpaccount/3.html
Start by leaving the path empty.

URGENT! Help Needed (H DISKS)

Dear Folks
PROBLEM: Suddenly, out of the blue without any changes, my computer has started doing this: It runs for 2 seconds then jamms for 10seconds, runs again for 2 seconds, then jamms again for 10 seconds. It doesnt matter what i do, even moving the mouse: it moves for 2 seconds then stops dead for 10 seconds, then moves 2 seconds, then stops for 10 etc etc
WHAT FIXES IT: As you will see frrom my sig, i have two identical SATA Maxtor 80GB Hard Drives connected via SATA. When i disconnect the slave drive (a drive which i only use to bakup large data) the problem fixes itself. I tried another Seagate drive (via IDE) and that doesnt seem to cause any problems. It only seems to occur with the two maxtors in SATA 1 & SATA2. But I have it connected this way for YEARS without ANY PROBLEMS. I dont know what is the problem.
Please help, i cant function without my seconds SATA drive it's got so much data on it i need!
Thanks
Best Wishes
Asmar

Dear Folks, heres the replies to your queries - some questiones too:
1) CPU TEMP is 48-49 Deg, SYSTEM TEMO is ~36 Deg
2) What is "event viewer" (sorry if thats a newbie question), where do i get access to it? I dont remember copying any new files from that drive or having any applications running from it. It simply is storage. I have two H Disks both connected via SATA to SATA1+SATA2 on the motherboard (next to the slots adjacent to the 'VIA' logo): The 1st one i run windows on and is partioned into three. The second disk (with which I am having the problem) is one single large partition I use for backing up data.
3) I dont have any 3rd HDD installed on IDE. Simply two S-ATA's as mentioned above.
4) I'll do some diagnostics on it - as mentioned below, i should use "SeaTools" yes? Or should i check on the maxtor website?
Thanks folks
Best Wishes
Asmar Akram

Urgent Help Needed - Frozen disk drive & mouse

This is quite a complicated situation, but i will put it simply:
I woke my mac from its sleep, and went to connect to the internet(wanadoo broadband. It wouldnt do it and went from saying 'connecting....connecting...'on the finder bar in the right hand corner(next to where the time is)and said 'disconnecting...' over and over. This usually last a few seconds but 5 minutes later it was still doing it, so i went to restart the mac.
When it was restarting, it went to the login page, and it never does this, so i went to use the mouse to click on it, but it wouldnt move from the top left corner of the screen. So, i used the keyboard to select it and logged in. Once it had got into the finder the mouse still wouldnt move. The time kept coming on and then disappearing again over and over.
I have tried opening Norton Disk doctor but i can select any options because the mouse wont work and a live update comes up before it opens and i cant select the option of not to use it. I have tried several things, i restarted using the on/of button and no change, i have unplugged all the usb devices but nothing has changed.The disk drive wont open either when i click on the eject key. So i cant reboot from a disc because
1)disk drive wont open
2)I cant click on the apple in the top left corner to go to the restart option and then hold down any keys.
The only reason i am on the net is cos i have used my flat mates pc to hook up on the net so i can get some advice, the apple helpline wont help me as i no longer have apple care plan, and i dont want to go out and travel to a different city to get hold of a new mouse, if it isnt the initial problem.
I really need help because i have work to do and deadlines to meet and even though i have the work backed up on an external hardrive, i cant access it because what i am using is a pc and my work is formatted for a mac. I also didnt get round to backing up all my music from itunes, so i really hope it doesnt come to formatting my hardrive because i dont want to lose all my files.
Can anyone help me please? Im desperate

StreeX,
If you have time, search the Discussions for "Disk Doctor Kervorkian". Symantec Systemworks / Norton Disk Doctor is widely and consistintly blamed for making things worse, sometimes irrepairablly so. (So be grateful you couldn't select it.)
You wisely unplugged other USB peripherals, but did you try unplugging and re-pluging the keyboard and mouse? Also try disconnecting your Ethernet (and phone line if any). The only peripherals should be the keyboard and mouse.
Does the mouse's red LED light up when the computer is on? Try both with the mouse plugged into the keyboard and with the mouse plugged directly into the Mac.
You can force the optical tray to open by holding down the mouse button while starting up. It's also possible to carefully (and gently!) pry the drawer and then the tray open with a fingernail of X-acto type knife blade.
You can force the Mac to restart unconditionally holding down command-control-eject (see Magical Macintosh Key Sequences)
Can you get the Mac to start up in Safe Mode?
With the optical tray open you can try booting from youe OS X Install disc to run Repair Disk to check for errors. An alternative is to boot to single-user mode and run the file system check utility. Refer to Using Disk Utility and fsck.

Time Capsule remote disk access

So i went into airport utility and enabled access disk via internet, enabled file sharing etc.
i put some movie clips and a couple of songs and files i wanted to access on there when im not at home.
music playback is fine....and editing PSD files off the disk is fine but movie playback is choppy at best...some of them are 20minute TV shows in both AVI and MP4 format tried in both itunes and vlc same scenario
i access the disk via various macs via Command+K enter my IP address.
(btw how do i get the same access to it via a windows based PC?)
is there a way to get a good stream remotely?
i tried via ethernet and 802.11n wireless
any ideas?

Here are some additional settings
Time Capsule=>Edit
hostname: [email protected]
username: my dyndns account user name at dyndns.org
password: my dyndns account password at dyndns.org
Disks=>File Sharing
Checked Advertise Disks globally with Bonjour
Secure Shared Disk: With Time capsule Password
Router:
Time Capsule's IP is set to DMZ plus enabled:
DMZ plus enabled explanation for 2Wire:Set the selected computer in DMZplus mode. All inbound traffic, except traffic which has been specifically assigned to another computer using the “Allow individual applications” feature, will automatically be directed to this computer. The DMZplus-enabled computer is less secure because all unassigned firewall ports are opened for that computer.
From a remote location, should afp://[email protected]/MyTimecapsuleDisk work? And will it work when the ip changes as it is dynamic?

Help Needed - Remote Disk Access via MobileMe for AEBS

Similar Messages

Maybe you are looking for