Help on Cisco AP1142

Hi,
i want to Use Cisco AP 1142 in my network. Also new to the enterprise edition AP.
I have configured AP WEB mode the SSID and able to connect without the Security Key. Also want to enable MAC Address filter on the AP
please help and provide the configuration details on web and CLI Mode.
Thanks,
Saroj

Hello ,
can any one guide me how to configure shared key associate with the ssid in Cisco AP 1142.
Thanks,
Saroj

Similar Messages

Need help configuring Cisco/Linksys wireless router to extend wi-fi signal to living room

My U-verse wireless gateway is in the back of our house. We live in an old 1920's home with solid wood walls. For our macbooks, we get a pretty decent signal, but my wife's iPad 2 get's poor wi-fi speeds. I bought a Cisco/Linksys WRT160N wireless N broadband router. I have a wired connection in my living room (going to a 4 port switch) then connected to my DVR. I tried hooking up the new router but ended up getting no signal on the iPad. In fact, it caused other issues. I ended up disconnecting it and re-booting my gateway. All came back fine. This wireless router replaces a similar unit that went out in after a power failure, so I know this can be done, but I forget exactly how I confiured the old one. I would like it to "extend" my signal to the living room, but I am also willing to create a new network (different SSID). Do I need to turn of DHCP? Are there any web sites that can assist me in configuring the router? I wish I didn't have to deal with this. The signal from the RG is great when you are in the back room (20+ down). But my wife gets about 3 down on her iPad in the living room. Thanks in advance.

Hi ,
I was doing some research on how this can be done. It does not appear there is an option in the Cisco router to set it up as an access point, but there are several options you can do to extend your network.
The first thing you can do is just set it up as a router behind router setup, and you will just have two separate networks. Make sure the DHCP pool does not conflict with the U-verse's gateway of 192.168.1.x.
The second thing you can do is connect the Ethernet cable to one of the LAN ports on your Cisco router instead of using the internet port. This should make it work like a smart switch.
With both setups, you want to probably change the SSID, network key, and wireless security settings to the same thing for wireless roaming abilities. That way, anyone that configures their wireless connection will be connected to both networks. Just make sure the wireless channels are not the same, and I would suggest having them at least 5 apart.
Hope this helps.
-ATTU-verseCare

Help with cisco ISE 1.1.2.145 patch-3 to ISE 1.2.0.899-2-85601 upgrade procedure

Need help from ISE experts/gurus in this forum.
Due to a nasty bug in Cisco ISE (bug ID CSCue38827 ISE Adclient daemon not initializing on leave/join), this bug will make the ISE stopping working completely and a reboot is required (very nice bug from cisco) . This leaves me no choice but to upgrade to version 1.2.0.899-2-85601.
Scenario:
- 4 nodes in the environment running ISE version 1.1.2.145 patch 3
- node 1 is Primary Admin and Secondary Monitoring - hostname is node1
- node 2 is Secondary Admin and Primary Monitoring - hostname is node2
- node 3 is Policy service node - hostname is node3
- node 4 is Policy service node - hostname is node4
Objective: Upgrade the ISE environment to ISE version 1.2 with patch version 1.2.0.899-2-85601.
My understand is that I have to upgrade the existing environment from ISE version 1.1.2.145 patch 3
to ISE version 1.1.2.145 patch 10 (patch 10 was released on 10/04/2013) before I can proceed with
upgrading to ISE version 1.2 and patch it with 1.2.0.899-2-85601.
Can I patch my exsiting environment from 1.1.2 patch 3 to patch 10 prior to upgrading to version 1.2.0.899-2-85601?
I look at Cisco website and patch 10 was released on 10/04/2013 while version 1.2 was released back in 07/05/2013.
I am trying to get a definite answer from Cisco TAC but it seems like they don't know either.
Question #1: How do I proceed with upgrading the current ISE environment from 1.1.2.145 patch 3 to 1.1.2.145 patch 10?
Propose solution:
step #1: make ISE node1 to be both Primary Admin and Primary monitoring. ISE node2 is now Secondary Admin and Secondary Monitoring.
         Then go ahead and apply ISE version 1.1.2.145 patch 10 to ISE node2 via the GUI,
step #2: Once ISE node2 patch 10 is completed, make node2 Primary Admin and Primary Monitoring. At this point, apply ISE 1.1.2.145 patch 10
         to ISE node1 via the GUI,
step #3: Once ISE node1 patch 10 is completed, make node1 Primary Admin and Secondary Monitoring and node2 Secondary Admin and Primary Monitoring,
step #4: apply ISE 1.1.2.145 patch 10 to ISE Policy Service node3. Once that is completed, verify that node2 is working and accepting traffics,
step #5: apply ISE 1.1.2.145 patch 10 to ISE Policy Service node4. Once that is completed, verify that node2 is working and accepting traffics,
Question #2: How do I proceed with upgrading the current ISE environment from 1.1.2.145 patch 10 to ISE version 1.2 with patch version 1.2.0.899-2-85601?
Propose solution:
step #1: Make ISE node1 the Primary Admin and Primary monitoring. At this point ISE node2 will become Secondary Admin and Secondary Monitoring
step #2: Perform upgrade on the ISE node2 via the command line "application upgrade <app-bundle> <repository>". Once ISE node2 upgrade is completed, it will
          form a new ISE 1.2 cluster independent of the old cluster,
step #3: Perform upgrade on the ISE Policy Service node3 via the command line "application upgrade <app-bundle> <repository>". After the upgrade the ISE
          Policy Service Node3 will automatically joins the ISE node2 which is already in version 1.2
step #4: Perform upgrade on the ISE Policy Service node4 via the command line "application upgrade <app-bundle> <repository>". After the upgrade the ISE
          Policy Service Node4 will automatically joins the ISE node2 which is already in version 1.2
step #5: At this point the only node remaining in the 1.1.2.145 patch 10 is the ISE node1 Primary Admin and Primary Monitoring
step #6: Check and see if there are any more PSN's registered in ISE node1 (there should not be any)
step #7: Perform the upgrade on the ISE node1 from command line "application upgrade <app-bundle> <repository>"
step #8: Once upgrade on ISE node1 is complete, ISE node1 will automatically join the new ISE 1.2 cluster,
step #9: Make ISE node1 Primary Admin and Secondary and ISE node2 Secondary Admin and Primary Monitoring,
Question #3: How do I proceed with upgrading the current ISE environment from 1.2 patch0 to 1.2.0.899-2-85601?
Propose solution:
step #1: make ISE node1 to be both Primary Admin and Primary monitoring. ISE node2 is now Secondary Admin and Secondary Monitoring.
         Then go ahead and apply ISE 1.2.0.899-2-85601 to ISE node2 via the GUI,
step #2: Once ISE node2 1.2.0.899-2-85601 is completed, make node2 Primary Admin and Primary Monitoring. At this point, apply 1.2.0.899-2-85601
         to ISE node1 via the GUI,
step #3: Once ISE node1 patch 10 is completed, make node1 Primary Admin and Secondary Monitoring and node2 Secondary Admin and Primary Monitoring,
step #4: apply ISE 1.2.0.899-2-85601 to ISE Policy Service node3. Once that is completed, verify that node2 is working and accepting traffics,
step #5: apply ISE 1.2.0.899-2-85601 to ISE Policy Service node4. Once that is completed, verify that node2 is working and accepting traffics,
does these steps make sense to you?
Thanks in advance.

David,
A few answers to your questions -
Question 1: My recommendation is to follow vivek's blog since most fixes and upgrade steps are provided there - I would recommend installing the patch that was release prior to the 1.2 release date since the directions to "install the latest patch" would put you at the version of when the ISE 1.2 was released
https://supportforums.cisco.com/community/netpro/security/aaa/blog/2013/07/19/upgrading-to-identity-services-engine-ise-12
You do not have the ability to install ISE patch through the GUI on any of the "non-primary" nodes (you can use the cli commmand to achieve this), the current patching process was designed so you can install the patch on the primary admin node and it will then roll the patches out to the entire deployment (one node at at time). I painfully verified this by watching the services on each node and when a node was up and operational the next node would start the patching process. First the admin nodes then the PSNs.
Every ISE upgrade that I have attempted as not been flawless and I can assure you that I have done an upgrade on 1.1.2 patch 3 and this worked fine, however I used the following process. You will need the service account information that is used to join your ISE to AD.
I picked the secondary admin/monitoring node and made it a standalone node by deregistering (much like the old procedure) in your case this will be node2.
I backed up the certificates from the UI and the database from the CLI (pick the local disk or ftp-your choice).
I reset the database and ran the upgrade script (since I did not have access to the vsphere console or at the location of the non UCS hardware [for a 1.1.4 upgrade]).
Once the upgrade was completed I then restored the 1.1.x database, ISE 1.2 now has the ability to detect the version of the database that is restored and will perform the migration for you.
Once the restore finished, I then restored the certificate and picked one of the PSNs
backup the cert,
Had the AD join user account handy
reset-db,
and run the upgrade script.
Once that is done I then restore the cert
Join the PSN to the new deployment
Join both nodes to AD through primary admin node
Monitor for a few days (seperate consoles to make sure everything runs smooth)
If anything doesnt look or feel right, you can shut down the 1.2 PSN and force everything through the existing 1.1.2 setup and perform some investigation, if it all goes smooth you can then follow the above step for the other two nodes, starting with the last PSN and the the last admin node.
Thanks and I hope that helps,
Tarik Admani
*Please rate helpful posts*

Re: Help on Cisco UC 520 Configuration

Dear All,
I am new to UC 520 Call Manager Express and Cisco Unity Express. I would like help in solving the following problems encountered during the config of the latter:
1. Call Transfer
- When I transfer a call, I need to know if the other person to whom the call will be transferred is available or not,
- if possible i should be able to put the current person on hold and call the other person and see if he is available or not before doing the transfer
- if ever a call is being transferred and the other person is busy or unavailable, the call should be reverted back or forwarded to another number instead of going to voicemail.
2. Configuring phones for call conferencing.
Please note the following details:
Unity Express Version being used: 3.0
Thanks in advance

Hi
1. In order to get transfers working the way you like, ensure you create ephone-dns as 'dual-line' - this allows one call to be on hold whilst a 'transfer' call is made outbound. Also ensure transfer-system full-consult is configured under 'telephony-service' mode. Basically transfers then are two-step - whilst on a call, hit transfer then dial the target extension. If they answer, announce the caller and hit 'transfer' again, or hit 'end call' to go back to the original caller.
2. You can enable three-party conferences by setting 'max-conferences' under telephony-service. It works the same way as transfer; hit 'Confrn' to start whilst on a call, dial another phone, and then when they answer Confrn again to set up the conference.
Regards
Aaron
Please rate helpful posts..

Help for Cisco 2960 48port switch not working

I had downloaded the template from the wiki for Cisco 48 port switch,unfortunately, it seems doesn't work.Are there other places where i can find WS-C2960S-48TS-L switch ? I also search the internet to find most people like to buy cisco product at Router-Switch.com with reliable quality and competitive price.Can give me the advice if i want to buy switch on this website ?

Please read over this FAQ and see if any of it might apply to you.
http://www.blackberryfaq.com/index.php/Errors_syncing_the_BB_with_Desktop_Manager
1. If any post helps you please click the below the post(s) that helped you.
2. Please resolve your thread by marking the post "Solution?" which solved it for you!
3. Install free BlackBerry Protect today for backups of contacts and data.
4. Guide to Unlocking your BlackBerry & Unlock Codes
Join our BBM Channels (Beta)
BlackBerry Support Forums Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

Help with Cisco

Hi all, I'm looking for some help regarding selling Cisco devices. I am a select partner whom did nothing for the first 2 years and just re-certified. I am now ready to make a big push to create a Cisco vertical in my company. I have the resources via Cisco for my marketing campaign and going to be doing some trade shows. My question is, I purchase the equipment via my distributor at my partner level price and now when I turn around to sell it to my client, what do I sell it for? What is the mark up? MSRP (and if so how do I find out what that is)? or something lower?
Any help would be appreciated.

The discussion was moved to the Network Infrastructure forum in the WAN Routing and Switching section.
I see a few things about this config that seem problematic.
In this DHCP pool
ip dhcp pool LAN
network 10.20.76.0
default-router 10.10.76.1
You have the default route in a subnet different from the client subnet. The default route should be 10.20.76.1.
Also it looks like you are trying to run the wireless vlan 10 to the dot1q subinterface of FA4. I do not believe that works.
Looking at the NAT configuration I do not see any particular issue and wonder if your real problem was really the default gateway and not the NAT.
HTH
Rick

Need Help Setup Cisco RV042 vpn

good day everyone, a month ago my boss purchase 4 pcs cisco rv042 vpn to be used in our small office and to our satelite office, with expectations of simple file sharing and remote troubleshooting and for better and safe data transfer. since the task is given to me as an IT staff it is difficult to me to setup this vpn router since i have a little idea and many question are on my mind that need to be answered, i read the manual test the vpn router but still no good answered found. i know it is dufficult but with proper guide and step by step on how to use this one i can make it work. please anyone help me i need answers to this questions.
i am using windows 7 pro sp1 64bit for my test unit, how can i make a vpn server? a client?
in the past i connect the internet connection in the internet connection port in the back of the router, then another cable from vpn port 1-4 i select #4 port to connect to my pc, since the vpn give the ip on my pc i can easily connect to the firmware of the vpn using the deafault username and password. when i go to the firmware i dont know where to start, and i dont even have the internet connection for my pc.
i feel sorry for myself beacuse i have no idea in this kind of thing, CISCO people and others out there i am calling for your help.
thank you in advance
mel

Dear Emilio,
Thank you for reaching Cisco Small Business Support Community.
If you’d like to setup a Site to Site VPN on your RV042 here is a good step by step guide;
http://sbkb.cisco.com/CiscoSB/Loginr.aspx?login=1&pid=2&app=search&vw=1&articleid=304
If you are looking into a remote access VPN, QuickVPN, here is the step by step procedure;
http://sbkb.cisco.com/CiscoSB/Loginr.aspx?login=1&pid=2&app=search&vw=1&articleid=452
Just in case here is also a document with Windows operating systems tips;
http://sbkb.cisco.com/CiscoSB/Loginr.aspx?login=1&pid=2&app=search&vw=1&articleid=2922
Finally here is a link with the Admin Guide where starting on page 122 you can find everything related to VPN setup on this particular device model, beside info in how to setup your internal network (I suggest you to go through this admin guide so you know everything about the router);
http://www.cisco.com/en/US/docs/routers/csbr/rv0xx/administration/guide/rv0xx_AG_78-19576.pdf
Please let me know if there is any further assistance we may assist you with.
Kind regards,
Jeffrey Rodriguez S. .:|:.:|:.
Cisco Customer Support Engineer
*Please rate the Post so other will know when an answer has been found.

Help with CISCO-887VA adsl over pots and PPPoE with dynamic IP

Hi
I've got problem trying to connect the CISCO-887VDSL/ADSL OVER POTS ROUTER to internet. Only got the LAN part working.
I'm trying to setup PPPoE with dynamic IP
Followed CISCO's documentations but the commands used were not recognized by the router. Any simple working config for me to follow will be enough.
I'll appreciate any help. Thanks a lot!
here's my config.
! Last configuration change at 08:31:51 UTC Sat Feb 11 2012
version 15.1
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname router
boot-start-marker
boot-end-marker
no aaa new-model
memory-size iomem 10
crypto pki token default removal timeout 0
ip source-route
ip dhcp excluded-address 10.0.0.1 10.0.0.149
ip dhcp excluded-address 10.0.0.199 10.0.0.254
ip dhcp pool sdm-pool
import all
network 10.0.0.0 255.255.255.0
default-router 10.0.0.1
dns-server x.x.x.x x.x.x.x.x
lease 0 2
ip cef
no ipv6 cef
license udi pid CISCO887VA-K9 sn FGLxxxxxxx
controller VDSL 0
ip ftp username cisco
ip ftp password cisco
interface Ethernet0
pppoe enable group global
pppoe-client dial-pool-number 1
no ip address
shutdown
interface ATM0
no ip address
no atm ilmi-keepalive
pvc 0/35
pppoe-client dial-pool-number 1
interface FastEthernet0
no ip address
interface FastEthernet1
no ip address
interface FastEthernet2
no ip address
interface FastEthernet3
no ip address
interface Vlan1
ip address 10.0.0.1 255.255.255.0
ip nat inside
ip directed-broadcast
ip virtual-reassembly in
ip tcp adjust-mss 1452
interface Dialer1
mtu 1492
ip address negotiated
ip nat outside
ip virtual-reassembly in
encapsulation ppp
dialer pool 1
dialer-group 1
ppp authentication chap pap callin
ppp chap hostname xxxx
ppp chap password 0 xxxx
ppp pap sent-username xxxx password 0 xxxx
ip forward-protocol nd
no ip http server
no ip http secure-server
ip nat inside source list 1 interface Dialer1 overload
ip route 0.0.0.0 0.0.0.0 Dialer1
ip access-list standard 1
permit 10.0.0.0 0.0.0.255
no cdp run
line con 0
line aux 0
line vty 0 4
login
transport input all
end

Try to check with your ISP the modem string to use for VDSL
and some ISP support direct dhcp on Ethernet0 without PPPoE.
An equivalent config is working for me in Switzerland with Swisscom.
N.B. "modem" under VDSL controller is enable using service internal !
service internal
controller VDSL 0
operating mode vdsl2
modem co5
ip source-route
ip cef
ip dhcp excluded-address 10.0.0.1 10.0.0.149
ip dhcp excluded-address 10.0.0.199 10.0.0.254
ip dhcp pool sdm-pool
import all
network 10.0.0.0 255.255.255.0
default-router 10.0.0.1
dns-server 8.8.8.8
lease 0 2
interface Ethernet0
ip address dhcp
ip nat outside
interface Vlan1
ip address 10.0.0.1 255.255.255.0
ip nat inside
ip tcp adjust-mss 1452
ip nat inside source list 23 interface Ethernet0 overload
access-list 23 permit 10.0.0.0 0.0.0.255
end

Need help on cisco CUCM license issue

Hi Team,
I am using 9.0 version CUCM . This machine i have cloned from some other CUCM .So after logging into to CUCM web admin i am getting an error like The system is operating with an insufficient number of licenses. Configure additional licenses in your Enterprise License Manager in order to restore the ability to provision users and devices. So i tried to login to ELM Manager for applying license .But ELM is giving an error like invalid username and password. I am using the same username and password which i used to login into cucm web admin .
So can some one please help on this issue.
Thanks,
Sasikumar.

Try this,
Unknown username and password for Enterprise License Manager login
Description
I do not know the username and password of the system when it was originally installed, so I cannot log into Enterprise License Manager.
Resolution
Log into the platform CLI with the OS administration credentials and use the license management list users command to view the username to use for signing into the Enterprise License Manager application. If you are not sure what the password is for this username, you can use the license management change user password command to change this password.
http://www.cisco.com/en/US/docs/voice_ip_comm/cucm/elmuserguide/9_0_1/CUCM_BK_E596FD72_00_enterprise-license-manager-user-90_chapter_0101.html#CUCM_RF_I970430F_00
HTH
Manish

Need Help on Cisco Wireless Solution!

Hello Netpros!
I have some issues that probably most of wireless implementers faced after implementing a wireless solution. This is an actual feedback from the customer and These issues can be broken down to the following:
1. The wireless Network is slow! (wireless performance)
The customer has Airtight in placed and airtight reports that users are mostly connected to the wireless network on 2 mbps speed. Users also says that their network experience using wireless are slow compared to wired network.
My question is what reports or guides that cisco wireless cotroller system or WLC can shows that proves the network is working as it is intended. Any guides on how to improve the user experience? Any guide from Cisco IT?
During these slowness, what reports from WCS or WLC that can best shows the problems and helps us implementers to mitigate the problem?
2. Baseline Wireless Performance.
When asked about a baseline performance of wireless network, what reports from the WCS or WLC that can show this and what is the acceptable or baseline values?
3. Is there a general guideline on how to use WCS or WLC reporting tools to troubleshoot a wireless performance issue? What reports to see? and how to translate that to say to the customer that the wireless network is under performing?
The main reasons i am asking these questions is because i cannot find any useful documents in cisco that guides the wireless implementers on how to use the reports generated by WCS or WLC when it concerns the performance of the wireless.
Most of the reports WCS generate that relates to the performance normally rounds up the AP performance, channel, noise, but how to translate that to user concerns is another matter.
Perhaps these issues are partly due to user expectations or maybe the wireless setup need to be tweaked or even might requires a spectrum analyzer to pinpoint interferences.
In either cases, I hope netpros can help direct me to good documentation albeit from cisco or other sources that can best outline wireless performance reporting using cisco wcs and wlc.
Background information:
The wireless network setup has one WCS, one location appliance, 4 WLCs and around 150 to 200 APs, most running Local and some running HREAP. Most of the issues concerns the local type APs.
Thanking all in advance!
maldin

Yup,
thats what we told the customer and even showed them the wlc/wcs reports.
Unfortunately, these customers are lacking in wireless knowledge and they want a streamlined, documented steps to generate the reports and also to help them understand in laymen terms.
At the moment we are formulating a holistic approach to the customer to get them understand wireless first, get them to have a policy and enforce and then drill down to management, reporting and troubleshooting.
The thing is, the wireless is always working fine, but sometimes so it happens some bigshots unable to connect to the wireless network in meeting rooms or somewhere and the become jumpy and pointing fingers.
So the IT manager wants to reduces the finger pointing by having the WLC/WCS to produce reports to them.

Help with Cisco Output Interpreter tool!!

Hi All,
I am experiencing a problem with Cisco Output Interpreter tool.
While the tool is working fine and displaying the "CONFIGURATION COMMAND REFERENCE NOTIFICATIONS (if any)" very effectively but I am unable to use the hyperlink to get an understanding about a particular command.
When I click on a particular command(hyperlink) it pops up another window and the below error is displayed.
Not Found
The requested URL /cgi-bin/Support/Cmdlookup/ios-command-lookup.pl was not found on this server.
Additionally, a 404 Not Found error was encountered while trying to use an ErrorDocument to handle the request.
Anyone else had/have this particular error. Could you please help me with this.
Apologies if this topic does not belong to this group.
Thanks in advance
Sam

Noone to help me on this?

Help for Cisco Security Manager

Hi All,
Please help me how cisco security manger is managing logs from different devices.
For example cisco security manager can manage FWSM, ASA, IPS devices.
Does it stores logs from this devices into some central location where CSM is being installed in some database or some file.
Can I be able to read logs for all those devices including CSM from one single point. Please help me.

Hi Bidyut,
When CSM services are running, Event Viewer can show the events in real time.
You are right about backup. When CSM application backup is running, its services on the server are stopped. So, there is a risk of loosing logging events that are sent to CSM server during the period of backup. By scheduling backup out of user-activity hours, risk of losing important events can be minimized.
On the other hand, events on IPS devices have to be polled from the device. So, there is no loss of IPS events in case of CSM application backup.
Thanks & Regards,
Chetan

Need help regarding Cisco 1841 Router

hello everyone , i am need of help regarding configuring of FE 0/1 port. our company have a cisco 1841 router. The serial 0/0/0 is connected with VSAT for internet. The FE 0/0 is connected to switch(LAN) through which net connectivity is provided to all users. Recently a new VSAT has been installed at our site,with different IP series. So every time we want to switch between the two net connectivity we need to change the entire IP configuration of all users, which in turn prohibits the users from accessing the printers,data servers etc which are been set to our existing IP series. So, my idea was to configure the FE 0/1, so that just by changing the DNS will help us providing internet along with all other devices without changing the entire IP series. The new VSAT modem has a lan cable which can be connected to FE 0/1. Can any one help out in solving the problem. Our existing IP series is 192.168.3.1..... and the new VSAT series is 10.205.74.1......

Bao
Do I understand correctly that you will have 20 remote users who will telnet to the 2511 and from the 2511 will use reverse telnet to access the console of router1, router2, router3, etc which have their console ports connected to async ports of the 2511? If that understanding is correct then the firewall only needs to open TCP port 23 for telnet. The other ports (2001, 2002, etc) are between the 2511 and router1, router2, etc and will not be seen by the firewall. If my understanding is not correct then please clarify.
I do not believe that you will find an image for the 2500 that supports SSH.
HTH
Rick

Need Help reactivating cisco valet plus after 2 yrs

I had previously installed the cisco wireless at my old apartment. I've moved since and now I'm having difficulty setting it up at my new place. The old network I created pops up but seems locked. But when I click connect using the easy set up I keep getting an error message saying that there is no internet connection. I refuse to pay to $39.99 for troublshooting support after already spending so much on the device. I tried to reset it to the factory setting but that didn't seem to work.
If anyone can help me I'd really appreciate it.
Thanks!

To set up a Linksys router, you need to perform four (4) steps using the computer that is registered with the ISP:
i. Verifying Internet connection
ii. Connecting devices together
iii. Checking the router’s LEDs
iv. Configuring a Linksys router for DSL Internet connection
QUICK TIPS:
The router’s power adapter needs to be plugged to your router and into an available power outlet.
If using a wired connection, the first Ethernet cable needs to be plugged to the computer’s LAN port into any of the router’s blue numbered Ethernet ports.
The second Ethernet cable should be plugged to the modem’s Internet port and the other end into the router’s yellow Internet port.
Ensure that you have no firewall enabled that may prevent the router from being detected.
Here is the link for setting up your Linksys Wireless Valet router for the first time using Cisco Connect: http://www6.nohold.net/Cisco2/ukp.aspx?vw=1&docid=e30f926604334d538668529cb50ad174_21463.xml&pid=80&...
If you still encounter problems installing the router using the Cisco Connect program, you may configure the router manually according to the type of Internet service you have. Follow the instructions below for your specific Internet service type:
To learn how to set up your router with Cable Internet service, here is the link: http://www6.nohold.net/Cisco2/ukp.aspx?vw=1&docid=0ff4c94586a345d082828ec2161aaecf_3686.xml&pid=80&r....
To learn how to set up your router with DSL Internet service, here is the link: http://www6.nohold.net/Cisco2/ukp.aspx?vw=1&docid=20ee1457387f40178cd5f41d4b585db4_3687.xml&pid=80&r... .

Help on Cisco Switch

My present LAN consist of 4 switches. 2 x 24 ports 2900XL Catalyst and 2 x 48 ports 2960G Catalyst. Crossed cables are seen connecting all these swtiches together. All the switches have only VLAN1. As I am running out of switch port and bought a 24 ports Catalyst 2960 Series SI LAN Lite image. Now i want to join this new switch to the LAN, how should i go about after configuring the swtich with an ip address up and running. Do i simply just find an available port in the last switch to plug in a cross cable to the new switchly setup switch? Do i have to use a particular port of any available port will do with the crossed cable? What are other things to take note? Any expert can help me out?

Hi,
For complexity reasons, let's name your switches
2900 = 2900-1
2900 = 2900-2
2960G = 2960G-1
2960G = 2960G-2
2960NEW
I'm not sure about the 2900 series but if you connect the 2960NEW switch straight out of the box with a crossover cable to either 2960G-1/2960G-2 and each port on 2960G-1/2960G-2 has its default configuration then they will form a trunk with out applying any commands in the IOS due to each Fast Ethernet port by default being set to dynamic desirable.
It depends if the 2960G-1/2960G-2 series has had all non trunk ports switched to access ports. If they are access ports then the 2960NEW will form static access link with 2960G-1/2960G-2, this will still carry traffic but not VLAN traffic, which in your case is ok are I believe you are not using VLANS respectively.
Just to note, in your scenario, is this a production network? Are your switches linked in a line? Sw1 > Sw2 > Sw3 > Sw4? Do you have any redundant (backup) links between the switches, so if 1 link fails all 4 switches can still communicate with each other? If not, I would advise looking into Spanning Tree Protocol.
In regards to configuring the IP on the new 2960, you will need to connect a console cable and console in to the switch. Search round the Cisco website for a document which explains the commands with examples.
Hope this helps,
Garry

Help on Cisco AP1142

Similar Messages

Maybe you are looking for