Help on how to setup a WRT320N as an access

I need help to setup a WRT320N as an Accesspoint. I also have a WAG320N as mt main connection to the internet. It settings are 192.168.1.1. It is also set for 50 users with a starting ip of 192.168.1.100
The setting I am trying to use for the WRT320N are as follows.
Internet ip 192.168.1.140
Subnet 255.255.255.0
DHCP is set to off.
The router ip I want to set is 192.168.1.2 but it will no allow this. Is there a work around.
Thank you in advance.
Regards
Solved!
Go to Solution.

1. Don't set an internet IP address. Leave it on Automatic/DHCP.
2. Set the LAN IP address to 192.168.1.2.
3. Disable the DHCP Server.
4. Connect one of the LAN Ports to a LAN port of the WAG320N.

Similar Messages

How to setup the guest network just access internet only (not touch in internal server)

I had setup the AirPort Extreme in basic and guest network, but observed the guest can access to our server currently, for the security issue, we can setup the guest network to access internet only? pleae advice and thanks

By default, a properly configured Guest network on the AirPort Extreme only allows network clients to access the Internet. No access to the "main" network's resources should be available.
This is assuming that the AirPort Extreme is the only or "main" router in your current network configuration.

Help Needed: How to setup external procedure in listener on 11gR2

I have successfully installed 11gR2 RAC on two nodes RHEL5.3, I noticed that the default configuration has something different from previous versions (such as 10gR2 or 11gR1):
(1) listener.ora is under $GRID_HOME/network/admin (a.k.a under Grid tree) not under $ORACLE_HOME/network/admin, and have a new file called "endpoints_listener.ora"
listener.ora under $GRID_HOME/network/admin:
LISTENER=(DESCRIPTION=(ADDRESS_LIST=(ADDRESS=(PROTOCOL=IPC)(KEY=LISTENER)))) # line added by Agent
LISTENER_SCAN1=(DESCRIPTION=(ADDRESS_LIST=(ADDRESS=(PROTOCOL=IPC)(KEY=LISTENER_SCAN1)))) # line added by Agent
ENABLE_GLOBAL_DYNAMIC_ENDPOINT_LISTENER_SCAN1=ON # line added by Agent
ENABLE_GLOBAL_DYNAMIC_ENDPOINT_LISTENER=ON # line added by Agent
endpoints_listener.ora under $GRID_HOME/network/admin:
LISTENER_NODE41=(DESCRIPTION=(ADDRESS_LIST=(ADDRESS=(PROTOCOL=TCP)(HOST=node41-vip)(PORT=1521))(ADDRESS=(PROTOCOL=TCP)(HOST=192.168.10.41)(PORT=1521)(IP=FIRST)))) # line added by Agent
(2) If I put listener.ora under $ORACLE_HOME/network/admin like 10gR2 including EXTPROC, then restart RHEL servers, the listener.ora under $ORACLE_HOME/network/admin doesn't take effect rather the listener.ora under $GRID_HOME does; however if I run "lsnrctl stop" and "lsnrctl start" the listener.ora under $ORACLE_HOME/network/admin will take effect.
listener.ora I added later under $ORACLE_HOME/network/admin:
LISTENER =
(DESCRIPTION_LIST =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = IPC)(KEY = EXTPROC1))
(ADDRESS = (PROTOCOL = TCP)(HOST = node41-vip)(PORT = 1521)
(IP = FIRST))
(ADDRESS = (PROTOCOL = TCP)(HOST = 192.168.10.41)(PORT = 1521)(IP = FIRST)
SID_LIST_LISTENER =
(SID_LIST =
(SID_DESC =
(SID_NAME = PLSExtProc)
(ORACLE_HOME = /u01/app/oracle/product/11.2.0/db_1)
(PROGRAM = extproc)
Questions:
<1> How to correctly setup extproc correctly under 11gR2?
<2> Will my way in (2) will affect the SCAN single IP access functionality? (I assume SCAN is enabled at least partially by listener.ora under $GRID_HOME such that client can use simpler connection string)
Thanks in advance.
Edited by: user5852271 on Nov 18, 2009 9:04 PM

user5852271 wrote:
I think the document you mentioned is for 11gR1 not for 11gR2. If that is the case, you could go to the 11gR2 library and check the Networking docs yourself at http://www.oracle.com/pls/db112/portal.portal_db?selected=4&frame=#network_management
>
I felt that the 11gR1 should be named 10gR3, and 11gR2 should be 11gR1 because 11gR2 introduced a lot more new features.Good one. You should join Oracle Marketing.

Help with how to setup property list correctly

I am developing an iPhone application and I need a database to store data.
Since it's small amount of data I'll go for Property List.
But I have zero experience with it. I was hoping you could help me set it up.
It's an app based on karate techniques required for each belt.
Firstly I need the top category to be the belt. and a subcategory for EACH belt to be Requirements, Stances, Blocks, Hand Techniques, Foot Techniques, Kata and Kumite.
How do I do that?

<?xml version="1.0" encoding="UTF-8"?>
<!DOCTYPE plist PUBLIC "-//Apple//DTD PLIST 1.0//EN" "http://www.apple.com/DTDs/PropertyList-1.0.dtd">
<plist version="1.0">
<dict>
<key>Rows</key>
<array>
<dict>
<key>Title</key>
<string>Belt 1</string>
<key>Children</key>
<array>
<dict>
<key>Title</key>
<string>B1 Requirements</string>
</dict>
<dict>
<key>Title</key>
<string>B1 Stances</string>
</dict>
<dict>
<key>Title</key>
<string>B1 Blocks</string>
</dict>
<dict>
<key>Title</key>
<string>B1 Hand Techniques</string>
</dict>
<dict>
<key>Title</key>
<string>B1 Foot Techniques</string>
</dict>
<dict>
<key>Title</key>
<string>B1 Kata</string>
</dict>
<dict>
<key>Title</key>
<string>B1 Kumite</string>
</dict>
</array>
</dict>
<dict>
<key>Title</key>
<string>Belt 2</string>
<key>Children</key>
<array>
<dict>
<key>Title</key>
<string>B2 Requirements</string>
</dict>
<dict>
<key>Title</key>
<string>B2 Stances</string>
</dict>
<dict>
<key>Title</key>
<string>B2 Blocks</string>
</dict>
<dict>
<key>Title</key>
<string>B2 Hand Techniques</string>
</dict>
<dict>
<key>Title</key>
<string>B2 Foot Techniques</string>
</dict>
<dict>
<key>Title</key>
<string>B2 Kata</string>
</dict>
<dict>
<key>Title</key>
<string>B2 Kumite</string>
</dict>
</array>
</dict>
</array>
</dict>
</plist>
Use Xcode to copy/paste more belts. Rename belts as needed.
This is only the plist structure for drilling down and does not include details for each category beyond the items shown.
You can't be doing any of this if you have zero experience - you'll have questions for every tiny step and unless someone builds your app for you, you'll go ahead very, very slowly.
It is up to anyone with zero experience to spend time going thru the most basic hello world tutorials, as an example, and learn enough to be able to gain some traction on their own...this is not trivial stuff that you can just install a few tools and make what you want the next day, sorry.
See this post for beginner resources:
http://discussions.apple.com/thread.jspa?threadID=2218661
- come back when you've exhausted those and need specific help untangling something or if you get confused as you progress on your own...not just in over your head at the very beginning.

I need help on how to setup hardware raid for ASM.

In the « Recommendations for Storage Preparation” section in the following documentation: http://download.oracle.com/docs/cd/B28359_01/server.111/b31107/asmprepare.htm
It mentions:
--Use the storage array hardware RAID 1 mirroring protection when possible to reduce the mirroring overhead on the server.
Which is a good raid 1 configuration considering my machine setup?
“I put my Machine info below.”
Should I go for something like:
5 * raid 1 of 2 disks in each raid: disk group DATA
5 * raid 1 of 2 disks in each raid: disk group FRA
Then ASM will take care of all the striping between the 5 raids inside a disk group right?
OR, I go for:
1 * raid 1 of 10 disks: disk group DATA
1 * raid 1 of 10 disks: disk group FRA
In the second configuration, does ASM recognize that there are 10 disks in my raid configuration and stripes on those disks? Or to use ASM striping, I need to have lots of raid in a disks group?
Here is my Machine Characteristics:
O/s is Oracle Enterprise Linux 4.5 64 bit
Single instance on Enterprise Edition 10g r2
200 GIG database size.
High "oltp" environment.
Estimated growth of 60 to 80GIG per year
50-70GIG archivelogs generation per Day
Flashback time is 24 hours: 120GIG of flashback space in avg
I keep a Local backup. Then push to another disk storage, then on tape.
General Hardware Info:
Dell PowerEdge 2950
16 GIG RAM
2 * 64 bit dual core CPU's
6 * local 300G/15rpm disks
Additional Storage:
Dell PowerVault MD1000
15 * 300G/15rpm Disks
So I have 21 Disks in total.

I would personally prefer the first configuration and let ASM stripe the disks. Generally speaking, many RAID controllers will stripe then mirror (0+1) when you tell it to build a striped and mirrored RAID set on 10 disks. Some will mirror then stripe (1+0) which is what most people prefer. That's because when a 1+0 configuration has a disk failure, only a single RAID 1 set needs to be resync'd. The other members of the stripe won't have to be resynchronized.
So, I'd prefer to have ASM manage 5 luns and let ASM stripe across those 5 luns in each disk group. It also increases your ability to reorganize your storage if you need 20% more info in DATA and can afford 20% less in FRA, you can move one of your RAID 1 luns from FRA to DATA easily.
That's my 0.02.

How to: Setup AAE for Remote Disk Access & Serve PS3

Hi there,
I've read so many tutorials, and tried so many combinations, but haven't found anything for my specific purpose.
I was wondering if someone might have the insight to do a quick run-through (including specific settings) on how I would setup my Airport Extreme for the following scenario/purpose.
Setup:
1. Netgear DGN2000 ADSL Modem + Router in one
2. Airport Extreme = Model #A1354
3. Western Digital Studio 1TB (mac os extended journaled formatting - not used as time machine)
4. PS3 80gb
*To accomplish:*
1. Access the Western Digital HDD remotely. So I can access my files from work.
2. Use the Western Digital HDD to serve media to the PS3 when I'm at home, so I can watch movies without having my computer turned on.
Caveat:
1. I don't want to use/pay for MobileMe.
Many thanks,
Glen

Hello nelga. Welcome to the Apple Discussions!
Since most of your questions are not really AirPort networking related, I will do the best I can to provide assistance.
1. Access the Western Digital HDD remotely. So I can access my files from work.
I know you don't want to use BTMM, but to best understand the hurdles you will be up against, it might be worth taking a quick look at how BTMM works "behind the scenes" to allow you to access a HDD remotely.
BTMM - Basic Communication Flow
o For a computer connected to the Internet via a router, BTMM "asks" the router for its configuration information. For a router, like your AEBSn, that uses NAT-PMP, BTMM will ask the router to assign arbitrary public ports. In turn, the router will provide these port assignments (& the router's Public IP address) back to BTMM.
o BTMM then sends this information to the MobileMe account. In background MobileMe updates a special set of DNS entries to be used by BTMM. These entries are then made available to all BTMM clients using your MobileMe account. When a computer, with BTMM enabled, uses your MobileMe credentials, it automatically retrieves a list of all other computers/routers that are registered with the same account. All these devices should then appear under the SHARED section of the Finder.
o When attempting to connect to a remote computer (or router), BTMM creates a secure connection to that remote device using the information from the MobleMe account.
o Once the connection is established, the devices can then communicate with each other.
The key to all this is that you will need the following in order to be able to remotely access the HDD:
1) Your ISP must provide you with a publicly reachable IP address.
2) If your ISP provides you with a Dynamic (vs. a Static Pubic IP address), you will need to keep track of that IP address in order to consistently have access to the HDD. Without knowing this address, when your ISP changes it periodically, you will have to manually "retrieve" it to connect again. You can get around this by using a service, like DynDNS.
3) You will have to configure your NAT router for port forwarding/mapping to allow the necessary file sharing communication to pass through the router to the AEBSn with the shared HDD. Specifically you want to open the appropriate ports for both the AFP (TCP: 548) & SMB (TCP: 445) file sharing protocols.
4) Similarly you want the AEBSn to be enable for file sharing.
2. Use the Western Digital HDD to serve media to the PS3 when I'm at home, so I can watch movies without having my computer turned on.
In order to stream video from your WD HDD, you will need a DLNA-compliant Media Server to stream that data to the PS3, which is a DLNA client. With that said, you will need at least one computer (Mac, PC, or Linux-based device) running in order to run this server. The WD HDD has no means to run this server as it has no operating system.

How to Setup WRITTEN as a wireless access point to work with WRITTEN

Hi,
I had a router WRITTEN which was not covering the whole space in my house. I was looking for a N wireless access point or a range extender.
The shop seller convinced me to buy WRITTEN saying that the Dual N will fix my problem.
well it did not. The reception in some locations is still poor.
the same reseller advised me to use the 350N as a wireless access point instead of buying one. The question is how to do it.
I am thinking about the following:
1- Have the WRITTEN installed next to the internet modem connect to the modem by cable
2- in another room have the WRITTEN (approx 20 meters away) not connected by a cable to the WRITTEN
3- When using the laptop in the weak reception area, I try to connect wirelessly to WRITTEN which should be also connected wirelessly to the WRITTEN
Would that be possible. I hope so since there is no way to have a cable connecting the 350N and 610N due to many reasons
appreciate your help in adance

I am sorry but the spelling checker repalced my router names to another word
the correct text is:
I had a router WRT350N which was not covering the whole space in my house. I was looking for a N wireless access point or a range extender.
The shop seller convinced me to buy WRT610N saying that the Dual N will fix my problem.
well it did not. The reception in some locations is still poor.
the same reseller advised me to use the 350N as a wireless access point instead of buying one. The question is how to do it.
I am thinking about the following:
1- Have the WRT610N installed next to the internet modem connect to the modem by cable
2- in another room have the WRIT350N (approx 20 meters away) not connected by a cable to the WRT610N
3- When using the laptop in the weak reception area, I try to connect wirelessly to WRT350N which should be also connected wirelessly to the WRT610N
Would that be possible. I hope so since there is no way to have a cable connecting the 350N and 610N due to many reasons
appreciate your help in adance

How to setup 24 hours guest network access with Time Capsule 4th gen. ?

Hello,
I just bought a Time Capsule 2TB and I cannot find the setting to limit the network access to 24 hours.
I updated the firmware and Airport Utility to the latest version and it seems that most of help on this setting I fond on internat are based on previous version.
By example I do not have a "Manual setting" in the "Base Station" menu like described in the manual.
Can someone help on this ?
Thank you and Regards,
Sebastien

Suggest that you download and install AirPort Utility 5.6 for Mac OS X Lion. It will have the settings that you are looking for.
You can keep both AirPort Utility 5.6 and 6.0 on your Mac and use the one that you need.

How to setup a company code for material management

Hi,
While creating material in MM01, in sales org tab, when I gave plant XXXX, it is giving an error "Company code YYYY is not setup for material management".
So can you help me , how to setup a company code for material management
Help is appreciated
thanks
DIL

Hello Sendil,
You can maintain it with trns code OMSY or MMPI/MMPV.
Hope this helps
Regards
Arif Mansuri

How to setup IM APPLICATION IN N95

ANYONE CAN HELP ME HOW TO SETUP IM APPLICATION IN N95?THANK YOU

Hi ronald_catahan
I don't know whether this link ticks any boxes for you:
/discussions/board/message?board.id=smartphones&message.id=46021#M46021
Happy to have helped forum in a small way with a Support Ratio = 37.0

1 How to setup new company name 2 How to setup row, rock and bin

Hi,
Anybody who can help me how to setup new company.
And also how to setup row, rock and bin because we need to assign a location for our spare parts inventory.
Thanks in advance.

Row/rack/bin sounds like an inventory system. For a simple system you might want to build your own from scratch, but for even a mid-sized company you really want a shrink-wrapped solution -- i.e. Oracle apps or SAP.
You don't want to be figuring out how to model material transactions, move orders, etc. Nor do you probably want to dive into various cost accounting options.

I am a OS10.7.4 user. yesterday i bought a Lacie external hard disk but error message appear said " You cant open the applicant LaCie setup assistant because PowerPC applicants are no longer support". please help me how to connect my mac with Lacie??

i am a OS10.7.4 user. yesterday i bought a Lacie external hard disk but error message appear said " You cant open the applicant LaCie setup assistant because PowerPC applicants are no longer support". please help me how to connect my mac with Lacie??

You do not need the Setup Assistant; in fact, you do not need any software on an external hard drive. I have two LaCie's; I erased the drive as soon as I plugged it in. You will need to format it anyway because most hard drives come Windows formatted. So, if you only want to use it with the Mac, highlight it in Disk Utility and choose Mac OS Extended (Journaled) as the format and the GUID Partition scheme under Options. While doing that, it will erase the drive (and get rid of the LaCie software) - once finished, your drive is ready to use for Time Machine or any other backup plans you have for it.

How to Setup Forward Error Handling in PI Scenarios. Can you help me with the same with screen shots if possible?

Dear all
How to Setup Forward Error Handling in PI Scenarios. Can you help me with the same with screen shots if possible?
Thanks
Regards
karan

Hello
These are the following errors
1. Trace level="1" type="T">no interface action for sender or receiver found</Trace>
2. <Trace level="1" type="System_Error">Application-Error exception return from pipeline processing!
3.
<Trace level="1" type="T">Application Error at Receiver... => ROLLBACK WORK</Trace>
<Trace level="1" type="T">System Error at Receiver... => ROLLBACK WORK</Trace>
<Trace level="1" type="B" name="CL_XMS_MAIN-WRITE_MESSAGE_LOG_TO_PERSIST" />
<Trace level="1" type="System_Error">Application-Error exception return from pipeline processing!</
Trace level="3" type="T">No persisting of message after plsrv call, because of config</Trace>Trace level="3" type="T">Error of the prevous version:</TraceTrace level="3" type="T">Error ID APPLICATION_ERROR</Trace>
tThere are repeating errors also.
TThanks
Regards
kkaran

I downloaded lion but lost the setup assistant. please help me recover the setup assistance. i do not know where/how to find/enter information in the terminal.

i downloaded lion but lost the setup assistant. please help me recover the setup assistant. i do not know where/how to find/enter information in the terminal as was suggested.

Launch the Terminal application; e.g., by entering the first few letters of its name in a Spotlight search. Copy or drag -- do not type -- the line below into the Terminal window, then press return:
sudo rm /var/db/.AppleSetupDone
You'll be prompted for your login password, which won't be displayed when you type it. You may get a one-time warning not to screw up. Confirm.
Reboot. The Setup Assistant will launch.

Help! Confusion over how to setup intel3945 wireless and rc.conf

Hi,
I'm very confused. I've already read through all the wikis and searched many forum posts. I can't get my wireless intel3945 to work on my dell vostro 1400.
Iwconfig says the wireless card is at wlan0 and dmesg | grep iwl says it has detected it. However, when I try a iwlist wlan0 scan it returns :
wlan0 Interface doesn't support scanning : Network is down
I think the problem is that I don't know how to setup rc.conf correctly or use the command line to test the wireless. Forum posts say many different things on how this is done.
These are the steps I have taken:
uninstalled the ipw3945 and ipw3945-ucode and ipw3945d.
installed iwlwifi and iwlwifi-3945-ucode
in my rc.conf modules, added iwl3945.
I'm not sure how to setup the networking section, this what I have now:
lo="lo 127.0.01"
eth0="dhcp"
wlan0="dhcp"
INTERFACES=(lo etho)
gateway="default gw 192.168.1.1"
ROUTES=(!gateway)
And in my dameons I have 'network'.
How can I scan for networks and connect to them on the commandline? I'd prefer not to use a gui tool because they never work and never tell me why they're not working.
Any help is greatly appreciated!
Cheers!
kilolima

iphitus wrote:
broch wrote:I have ipw3945 and iwl3945 working with wpa2 (or vpn)
(less complicatd than the above)
don't use netcfg2
Why?
no particular reason.
Simply when I configured wireless, netcfg2 wasn't available. Since then it (wireless) works, so not having any problems, I did not modify network setup. Next week or so I am going to install Arch on my daughter's laptop (per her request ) so I will try netcfg2.
So this is what I have for ipw3945 wpa2 or iwl3945 with wpa2
Below you will find a lot of words so read slowly but there is not much actual work
ipw3945 setup
kernel 2.6.23.x (Arch or vanilla)
or
kernel 2.6.24/2.6.24-gitX (patched with ipw3945 patch from gentoo -> compiling separate module for 2.6.24 may fail. if you want kernel patch I can post a link)
for default kernel install Arch packages for ipw3945, ipw3945d, ipw3945-ucode
or
if you want to compile modules, you will also need ieee80211 (first uninstall kernel's default, then install from sources otherwise ieee80211 from sources may refuse to install)
modify /etc/rc.conf
DAEMONS=(.... @ipw3945d @network ....)
that is all you don't need to add ipw3945 to MODULES=(.....)
because ipw3945d will automatically start ipw3945 module
do not list eth1 in network config section:
lo="lo 127.0.0.1"
eth0="dhcp"
INTERFACES=(eth0)
as you see, in my case only eth0 (wired) is listed and eth1 (wireless) is not listed
now you are done with basic network configuration for ipw3945, restart network/computer to bring up ipw3945d/ipw3945
check if modules are up and basic network is set:
#lsmod | grep ipw
#ifconfig -a
or
#iwconfig
if all is o.k. configure
WPA2:
configure router for wpa2
client: basically follow Arch wiki:
configure wpa_supplicant (installed already of course)
#wpa_passphrase your_ssid your_psk
keep terminal window open with created encrypted wpa passphrase and in the second terminal window edit /etc/wpa_supplicant.conf
ctrl_interface=/var/run/wpa_supplicant
network={
ssid="your_ssid"
scan_ssid=1
proto=WPA RSN
key_mgmt=WPA-PSK
pairwise=CCMP TKIP
group=CCMP TKIP
psk=whatever_output_from_wpa_passphrase
Above pairwise and group setup will depend on your router (network capabilities)
almost done:
run
#wpa_supplicant -Bw -Dwext -i eth1 -c/etc/wpa_supplicant.conf
the above assumes that your ipw3945 is set as eth1 (from iwconfig output)
to connect to the network I am using "wireless assistant" http://www.kde-apps.org/content/show.ph … tent=21832
that is all for ipw3945. You may automate network starting/connecting to wpa2 by writing simple script.
iwl3945
--kernel 2.6.23.x
install iwlwifi and iwlwifi-3945-ucode
--kernel 2.6.24.x
install only iwlwifi-3945-ucode as kernel has iwlwifi module incorporated
default iwlwifi does not support LED so I suggest to install something like knemo for kde to show active network icon. The latest iwlwifi does support LED but it is not yet incorporated into 2.6.24 vanilla kernel.
if you have kernel 2.6.23.x with external iwlwifi module
modify /etc/rc.conf
and add iwlwifi to
MODULES=(.....)
nothing else is required.
if you have kernel 2.6.24 with integrated iwlwifi module you don't have to edit /etc/rc.conf
As in the case of ipw3945, I do not list wireless interface (wlan0) in /etc/rc.conf
for kernel 2.6.23.x
load module/restart network or simply restart computer
check if module is up
#lsmod | grep iwl
#iwconfig
or
#ifconfig -a
WPA2
same wpa_supplicant.conf as above, so if you already have it no need for modifications.
start wpa2
#wpa_supplicant -Bw -Dwext -i wlan0 -c/etc/wpa_supplicant.conf
the only difference in the command is wireless interface: wlan0
connect to the network, again I am using "wireless assistant"
vpn
I am using cisco vpn. Client is provided by vpn host, cisco does not provide vpn client for individual download, but you can find it on line.
vpn host will provide pcf file for you
- install vpnclient
- copy your VPN profile (vpn.pcf) to the
/etc/CiscoSystemsVPNClient/Profiles
directory
-- start vpn client
/opt/cisco-vpnclient/bin/vpnclient connect vpn pcf_file_name
provide username and password and off you go
From my experience none of linux gui for vpn works reliably so you will have to resort to the command line.
That is all, a lot of writing, but actual ipw3945 and iwl3945 configuration is straightforward and very short.
Hopefully this will work for you.
forgot to add regarding vpnclient (cisco)
you will have to modify
/etc/init.d/vpnclient_init
line 38 and line 101
replace
/sbin/lsmod
with
/bin/lsmod
Last edited by broch (2008-02-07 15:55:45)

Help on how to setup a WRT320N as an access

Similar Messages

Maybe you are looking for