Help on MSI 6116

Can anyone help me on what to do....
I have bought a MSI 6116 and every time i boot up, it says CMOS Checksum error - Defaults loaded.
Warning! CPU has been changed.Please re-enter CPU settings in the CMOS setup and remember to save before quite!
I already replaced it with a new battery.

Hello Assaf
Applied the appropriate settings and so far im not encountering that problem anymore. Thanks again for the BIG HELP

Similar Messages

MOVED: Need help with msi mega 180 + athlon xp-m combo

This topic has been moved to Overclockers & Modding Corner.
Need help with msi mega 180 + athlon xp-m combo

AFAIK, you shouldn't need a pinmod for a Mobile Athlon XP CPU to work in a nforce2 mobo
did you have any other CPU installed prior to this one? if so, refer here to clear the CMOS: Clear CMOS Guide
next, refer to your manual, or download from MSI, for location of the FSB jumpers; ensure J8 is shorted across pins 1-2, and J7 is shorted
finally, enter your BIOS setup menu, and under Advanced Chipset Features, set CPU FSB to 133mhz (or even 166mhz if you have DDR333 memory). the only thing i can't see in the Mega 180 manual is where you set the multiplier...
which is where the BIOS has limited overclocking features, and you might have a problem here
i think i'll pass this over to the Overclockers forum, where someone may be able to give a better answer....

[HELP] My MSI External Hard Drive Enclosure cannot be recognized by my laptop...

As the subject tells my MSI cannot be recognized by my laptop...
At first I thought that my laptop is the one at fault but i tried inserting it on my friends computer but still doesn't work.
Then I blame the USB connector but tried using it on other devices and it works.
The only one left to be blamed is the device itself.
the model of this device is MSI UH1000-K500
Before this device broke(i guess) I am copying my important files to my PC.
I cant seem to see the drive in my "drive manager".
But I can see it on "Devices and printer"
Can anyone help me how to fix this?
I really need your help...

nope it didn't got partitioned/formatted...
I'm sorry for late reply been busy this past few weeks...
I already returned the device on the seller because it is still in warranty period...
thx for the help anyway...

Need Svet's Help! MSI GT70 492-US

I recently sent my laptop into a repair center (Non msi to my mistake) where the person replaced the motherboard with a new one. Upon replacing the motherboard the repairman also wanted me to pay for a new keyboard, stating that the keyboard was acting erratically, and is need of a repair. However, I'm starting to think it has something to do with software issues pertaining to the bios. Every key is functional, but is mapped to do something else. The letter h, for example types out the letter b. I see there's another thread extremely similar to the problem I am facing and the person found a solution, however he was not coherent in explaining the solution and was one of those people who fixes the problem without gratitude nor informational sharing. Therefore, I am pleading to the experts on here to please help me with this issue as it is extremely annoying.
Also, another generic optimus problem. With every single game I play, the white optimus light is on the power button, and FPS does not seem to correlate with the machine's expected performance. I did do quite a bit of research before typing this out but no BIOS tweaks or anything of that sort. I set the default GPU to the 675mx, ran it using the 675mx, I'm monitoring the gpu activity, everything, yet it still lacks that hmmpph and framerate drops occur in games as old as SPORE.
Please note that I am very willing to donate for a private bios or EC or ANYTHING that will be the god-like solution to the many problems I am facing now, and faced before the "repair of this laptop". So from anything like being able to overclock the monitor above the 60hz intel-forced limit, to overclocking the CPU; I am willing to pay.
Thanks in advance!

Quote from: Svet on 02-June-14, 03:27:56
you can create a bootable USB key by following this guide:
http://www.bay-wolf.com/usbmemstick.htm
once done extract all files that i give you and copy them to the USB stick
then reboot notebook and press F11 and then select the USB key to boot from
when you see A:\ or C:\, type:
ecall.bat [ENTER]
Alrighty, these instructions seem easy enough. It seems to be taking quite a while to format the usb disk, so in this time, I'd like to get straight to the money stuff. How easy is it to use your legendary software edits? I am definitely not as tech-savvy as most people on here so I really don't want to screw up my system, yet I am very much willing to gamble to improve the performance of my pc. Will we speak on a 1-on-1 basis to tweak my pc? I'm completely new to this, sorry for all the questions.

Need help with MSI P45 Neo3-FR

I haven't been here in a long time. My old board (just replacing it) worked perfectly for almost 4 years after I ironed out the kinks (MSI 865p Neo2-FISR) but I finally decided to upgrade my rig, but here comes the headaches...
I bought the following for my new setup:
MSI P45 Neo3-FR (came with BIOS 1.3 installed)
2GB (2x1) Corsair Dominator 6400C4D
MSI Radeon HD 4850
Intel Pentium Dual Core E2180 (I want to overclock it hehe)
Lite-On SATA CD/DVD-RW
Old Hardware being used:
Antec TruPower 550W EPS12 (single rail 36amps on +12)
Cooler Master Centurion (forgot what model) Case
Logitech USB Keyboard
Logitech MX518 USB Mouse
2x120mm fans
2xMaxtor SATA 80GB HDDs (note: NOT SATA II, and I want to run these in RAID 0 off the ICH10R, this is specifically why I bought this board I was going to go with the P43-Neo3 over this, but the inclusion of RAID sold me on it)
1xMaxtor SATA 160GB HDD (note: NOT SATA II)
Aside some trouble I had with the Intel HSF installation was a breeze. Everything is in. I wanted to run everything stock first. Jumped into the BIOS and set the following:
SATA Controller - RAID
DRAM Voltage - 2.1v
Drive Layout:
SATA1 - 80GB Maxtor
SATA2- 80GB Maxtor
SATA7 - Optical Drive
SATA8 - 160GB Maxtor
First power on to get into the BIOS was quick. After setting SATA to RAID, POST will hang at Auto-Detecting ACHI Port 1....then find HDD after about 20-30 seconds. And it will repeat itself for Port 2. So its taking me close to a minute (I might be exagerrating but it sure isn't quick and long enough to irritate me having to keep booting) just to POST and even access the BIOS.
Tried to use my current Windows XP install, got to the Windows XP Splash screen and it rebooted. Tried again, with super long ass POST, again rebooted at the splash screen. Said, fine I'll reinstall XP.
While browsing here I forgot where I read about the SATA and long posts, so I changed my 2x80GBs to SATA3 and SATA4, it no longer takes a minute to POST, goes quick as normal.
Set Optical to boot, go into the Windows XP Install screen, F6 for custom drivers, made a RAID disc using three sources (1. RAID drivers from MSI Website, 2. RAID drivers from MSI CD included with Motherboard, 3. RAID Drivers from Intel website) and each time at a certain point I'd get a BSOD.
Tried again by moving my last HDD/Optical to the ICH10 and disabled the Jmicron. Same, BSOD.
Switched off RAID in the BIOS and set it to IDE. AGain BSOD at XP Install.
Started to think it was a Memory issue, ran Memtest both sticks passed.
One thing I noticed in the BIOS, it has my RAM clocked at 1066. Everything is on auto minus the voltage, but I didn't think it would affect it. So I changed the Ratio from auto to 1:2 (800mhz CPU:800mhz DRAM) but still BSOD everytime I try to install Windows.
This is getting frustrating. I've run out of ideas. Any help would be greatly appreciated.

Quote from: BOSSKILLER on 02-August-08, 22:07:06
Read here how to do it:
>>> Slipstreaming Windows XP Service Pack 2 and Create Bootable CD<<<
>>> Slipstreamed Windows XP CD Using SP2<<<
Other option is borrow such installation disk from friends.
I moved away from my "friends" and none PC literate, so I'd be better off driving to the store and buying Vista at this point. Haha.
Okay, going to try this...sounds like that project I started a whiles back but got lazy.
Thanks guys, I'll report any results.

Help Too MSI GX640 Intel Core i5 Processor 2,2.6

Hi hope you can help me
I have a MSI GX640 Intel ® Core ™ i5 Processor 2,2.6
I would like to have a higher CPU in've heard it may well do
Intel ® Core ™ i5 Processor 2,6.7 perhaps more I hope it will in time at
The reason I do not buy the new model is that it has firewire as my new HD camera
so, I prefer this design usually one is also
what else can I do enough I need firewire could dilate
may awnings me wrapped Intel ® Core ™ i5 Processor I can go out to buy and put in
it is in is an i5 430M I know that it goes beyond my warranty on used and Inge on
it is my understanding
so I can get it to be 2,6,7 welcome increased
Regards Søren

Hi HarmitClaire,
Welcome to the Apple Support Communities!
I understand that your MacBook Air is not charging as expected. In this situation there are troubleshooting steps that I would recommend. Please use the attached article as a resource for steps to help you resolve this situation.
Mac notebooks: All about batteries - Apple Support
My battery is not charging
Confirm the correct wattage AC adapter for the computer. A power adapter rated for a lower wattage than is required for the system may not reliably charge the computer. For assistance identifying the proper adapter, review Intel Based Mac notebooks: Identifying the right power adapter and power cord--US. Additional adapter troubleshooting is available in Troubleshooting MagSafe adapters. If issues persist please reset the SMC.
Best regards,
Joe

Really need help with MSI R7970-2PMD3GD5/OC:(

Greetings to all,
I really need help with my brand new MSI R7970-2PMD3GD5/OC. I've purchased it two days ago and I didn't really have time to test the card until yesterday. The card is I think way to hot for my "liking". It idles at 56c-60c, at full load in Heaven benchmark 3.0 in 1920x1080, extreme tessellation and 8xAA card reaches 95c-97c. Stock cloacks are 1010Mhz/1375Mhz and stock voltage is 1,174v. Case is being cooled by two Noctua NF-P12 fans. Also I tried lowering the voltage and "underclocking" the card to a standard 925Mhz in small increments, but it doesn't help at all. Each and every time it results in BSOD and dx dll errors and complete system failures. Replacing the card wouldn't be a problem if I lived in a "normal" country that has access to a steady supply. Retailer that sold me a card told me that only 5 cards total have been imported from the launch day and told me that i bought the "last" card in my country. They could order a replacement but it would take them more then a month to do so.:( Ohhh and one more thing I don't overclock, everything in my case is at their default values.
Recently, I read that "Amd released" a bios update for a standard reference boards that turns them into a "GHZ editions". Also lot of users report a lower voltage requirements and lower temps with that "boost bios". As I understand this card pcb is not Amd's reference board design, I could be wrong it's not that uncommon.. So I didn't want to risk warranty by flashing it to a position 1. Will MSI release the boost bios for this model of card? I am humbly asking MSI staff on how to proceed regarding this problem. I would be immensely grateful for any help you could provide.

Quote from: Svet on 24-August-12, 18:13:26
what PC case you use exactly?
have you tried to open PC case side door and to retest?
Hi,
it's open case. If i close it the temps get even worse:(
They get better for other components, but not for gpu. Two Noctua NF-P12's are cooling the case, first one is positioned above gpu, left side next to cpu. Other is right beneath the gpu, right side of case. Just under the hdd section of the case. I tested each and every component with my backup card nv 8500gt. They function within the specified parameters. I'm getting somewhat worried.
П.С. Поздрав Свет
да ли сте ви са наших простора да не куцам на енглеском?

Please help with msi k9a2 platnium

ok well i just finished building my rig.
its a Antec 900 case
2x 80 gb 7,200 rpm sata HDD
1x 720gb 7,200 rpm sata HDD
ATI hd 4870
AMD Phenom x4 9950
Thermaltake Water Cooler
CORSAIR Dominator 2GB (2 x 1GB) 240-Pin DDR2 SDRAM DDR2 800 (PC2 6400)
corsair 750 watts crossfire support
ok well i put it all together.
my power works and motherboard is all lighted up.
VGA has 3 red lights( means its workin)
all fans are up, leds are workin.
ok then when i switch on my power supply. before i turn on the system.
in the middle of my motherboard, i see a yellow led light. its small. i dun think its bad. so i continue.
i connect my screen keyboard and mouse. btw screen is new and tested. ( it works)
i turn on comp. Fan turns on, water cooler works, and lights flash.
then all of a sudden, nothing shows up on my screen. its blank. it says there is no signal. i checked my video card. everything is fine with it.
i check my ram and its all fine.
oh btw my motherboard is k9a2 platnium. and i see in the middle where the model is. its version 1.0
do i have to flash my bios?
if so how do i? cause i dun have a screen. and nothing will show up on my computer.
can someone tell me how to flash so that my phenom 9950 will work i think thats the reason or can someone help me. cause msi never picks up their technical support. ( its horrible) so help me plz. Thanks
Tam

Quote from: tamngoman on 16-August-08, 10:54:13
um i dunno where that pin is. where am i suppose to find it from? am i suppose to have it?
cause i connected the 4 pin on the bottom of it ( next to the audio ports)
Yes, its "tricky" a bit
Find and connect EPS/ATX12V 8-4 pin cable for the CPU. But deattach it 1st: /* Its 8pin, one piece by default */
Once done plug it to JPWR1:
Quote from: tamngoman on 16-August-08, 12:10:07
ok and that should fix the problem with the booting?
Yes, you can't boot without it.

I need help in msi enjoy 7 plus tablet

Hi everybody i need to unscrew the back of the tablet msi enjoy 7 plus to fix a problem in the speakers but obvious there is no nails in it. could anybody help me.
thanks in advance

Enjoy 7 Plus is not meant to be opened by users. Contact MSI support for repairs as it should still be covered by warranty: >>How to contact MSI.<<

HELP! MSI GF615M-P33 7597 Ver 1.3 BIOS needed!

Hallo!
Please help. on GF615M-P33 7597 Ver 1.3 (!!Ver1.3!!) BIOS crashes :( But Bootlock is alive and Ctrl+Home works ok.
I cant find BIOS for this motherboard.
Please make a dump of this bios if you have same ver 1.3 http://www.msi.com/index.php?func=proddesc&maincat_no=1&cat2_no=171&prod_no=2134 motherboard and send me **Email-Address removed to protect user from spam**
best regards! Pavel

http://www.msi.com/product/mb/GF615M-P33-V2.html#/?div=BIOS
sn: 601-7597-100b1008615634
when i put the 3 files on my usb stick, an then go on my msi pc i put in usb port and go on my pc.
they print me on the screen:
"FILE NOT FOUND
PLEASE COPY LAST BIOS.... ..."
i would like to download the bios from the site but is only live update5.
My MSI pc is bios cleaned in the moment i work with him i'm not put upgrade or anything else but i work for my office and in a moment they say me this....
:bonk:Virus??? i'm not understand!!!!

Help with MSI K7n2 Delta2 Platinum

Hi everyone,
I need some help with my system, actually I'm having troubles with my machine, often it restarts or freezes so I have to restart it manually.I own a MSI K7n2 Delta2 Platinum, AMD Athlon XP 3000+, 1 GB DDR-400 CORSAIR, ATI Radeon 9800 PRO 128MB AGP. Recently I did a clean install of Windows XP but usually I work for an hour and suddenly it restarts, and after logging in, Windows reports a log event problem; I think I have this problem because of the drivers, so I would like you to help me. Where I can get the best/last drivers for the mainboard and video card? Should I flash the bios? Is common this kind of problems? Help me please.
Thanks!

sortieins, please start an new thread and make a complete listing of your compoenents including your PSU and the amps on the various voltage rails, especially the +12V rail(s).
>>Posting Guide<<

Help on MSI Ti4800

Greetings to all!
I'm very sorry, but i didn't have no other solution that ask for you help. I know this kind of problem has been discuss in many other posts, but this problem still exist, even after i tried all the actions posted in these messages.
My problem is:
After the installation the MSI Graffic Card, i can do almost everything (e-mail, work, excel...) but i can't play any gamesFS2002,Subcomand,Morrowind,POW, OP.Flashpoint,GP4 and so on).
After the game loads, i can manage to play for some time (+-10/15 Minutes), but suddently the screens goes black and i return to my desktop.
I have try almost everything (format c:, try different VGA drivers, Low settings, DX8.1 and DX9.0), but no sucess!, the problem appear again.
I have check the settings on the IRQ and the graffic card is not sharing IRQ with no other card, so at this time my solutions have run out. ;(
In resume:
Can be a problem with the power suply?, what is the correct specs to a compatible power suply for this card?
Can be a problem with the compatibility with my board?
My Specs:
PIV 1.7Ghz
Seagate 40Ghz
Sound blaster pci128
Samsung CD 52x
Samsung CDRW 16-10-32
Mainboard: Asus P4B - With the last driver available:1012
MSI TI4800SE - VDT8x - Driver 42.75
DirectX 9.0
1024mb SDram
PSU 260W
Samtron 96B monitor
Windows XP Pro
Yestarday i receive a information from MSI Support, that adviced me to upgrade my Ram memory, so i pass from 512Mb SDRAM to 1024Mb SDRAM, but the problem still lives on! ;(
Now i am almost desesperated! almost crying for the money invested in this card!.
Sorry for this long message, i really appreciate all your help and comments.
Thank you very much
Sincerely Yours,
Mário Silva
Portugal

At this moment, i think i resolve the problem, thank for your help!
I change my PSU260w, for a new one, a Qtec 550w dual fan gold (http://www.q.tec.info)
until now, morrowind, gp4, fs2002 are working just fine and i hope they continue for a long time! :D
With this issue resolved, i have another litle problem about the creation of a registry entry, to enable the hide features on 3dTurbo. if you are able to help me, i have post the following message:
http://www.msi.com.tw/program/service/forum/index.php?threadid=14318&boardid=9&styleid=1&sid=1b91092575adc769978046be2ffc60a1
thank you
Mário Silva

I need help with MSI CR52-A2 52x24x52x CDRW Drive

Hi,
I am running Windows XP Home Edition. My MSI CR52-A2 52x24x52x CDRW Drive will not work. When I restart my computer the light on it flashes red, green, red, green, red, green, etc... When XP is running, if I click on the drive under "My Computer" it opens up the drive but no files are found. If I try to add new hardware, I'm told that the drive is working properly. When I try to burn a CD with Windows Media Player I'm told no CD Burner is found on my system. Please help! Does this have to do with the BIOS?

Welcome to the forum superaverage.
1) Before posting any problems related to your optical drive, please post full system specs AND PSU rails (look at my signature).
2) Tell us how do you have your drive setup (Master, Slave, in primary channel or secondary channel).
Edyros!
The recommended setup for ANY CD-R/W or DVD-R/W is to set them in the secondary channel as secondary master (assuming that your primary master is your HDD).
If you're using nero as your burning program, try downloading the latest ASPI drivers for windows XP.
Try flashing your drive's firmware to support more media and to fix minor bugs.
ALWAYS use an 80-conductor IDE cable for ANY drive.

Help with MSI K8N Neo Platinum

HELP please- motherboard MSI K8N Neo PLATINUM: I tried to take away the backplate for the heatsink (on the back side of MB) in order to install the zalman HS beafore i read the forum (use a fan...) and the worst of all happend:
I scratched the back surface!! the scratches are minor, that is 4 scratches half a milimeter long each and not deep but i can see the copper of some lines leading from the memory slots to the processr. My question is : can I try and build the computer on that motherboard anyway or better buy a new one? is there a risk of dammaging other components? oh god what a mistake!

Make sure the new backplate is non-conductive. The backplate for the Hyper 6 has a non-conductive sticker on it. Make sure to keep it on if youve got one... If the lines are exposed even with the back-plate on perhaps you should cover them with some non-conductive (100% non conductive!) tape or something.
Then it doesnt matter if they are exposed, as long as they are ok.
A good tip, which got when i was removing my backplate, is to use a blow dryer to heat it up and the remove it with your fingers. That way youll also notice if it gets to hot
The glue gets sticky at blow drier temps. And pls, dont singe the MB with your blow dryer, you only have to make it hot, and if you cant touch it, how can you remove it with your fingers?
I guess theres no way of telling if you have a serious prob and no way to tell if your cpu will be ok. I guess you could (?) try and start it wíthout anything (cpu, mems) but a PSU, and then, if it (and maybe the PSU) goes "!Pfsssssss!" or "bang!", youll now you will have to replace it.
I put a screwdriver through an asus board once, and it still worked...

Need help with MSI GeForce 6800. Pc says its an LE...

Hi all I did a search but couldnt find anything relating to my problem. If I missed it then I apologise in advance.
I bought an MSI 6800 and installed it but it says that the card installed is a 6800 LE.
All the packaging and the stickers on the card itself say its a 6800 but the pc says otherwise.
I installed all the software and searched for updates. I installed new drivers but still it says its an LE.
How can I find out if I got a duff card or a problem with windows and drivers ??
Is there a major difference physically on the pcb that I could check out ?
cheers.
JunkDuster

Thank you very much for the pictures.
I did what you said and guess what, yep, it said 6800 LE.
I now have the great displeasure of having to pay for postage to return this item and hope that I can get a full refund and go elsewhere.
That was the first and last time I will use that company again.
Cheers for your help in stopping me from getting ripped off.
JunkDuster

Help on MSI 6116

Similar Messages

Maybe you are looking for