Help on MSI KT4AV(MS-6712)

hi
i have assembled a pc using......
Motherboard -    MSI KT4AV(MS-6712),
CPU -       AMD Athlon Xp 2200+,
Graphic Card -    MSI G4 MX440-T8X (8895),
Ram -       Hynix 256MB DDR ( ),
HDD -       Samsung 80GB 7200RPM (SP0802N),
Combo Drive -    LG (GCC-4480B),
Sound Card -    In-built,
Monitor -     Samsung 15",
Modem -     Internal (Smartlink 56K ),
PS -       Un-branded good quality,
there are some problems,
1) i am unable to get the pictures on my TV screen,
i dont know how to connect the TV-OUT connector to my TV.
2) my system was showing athlon XP 1500+ before but after i visited the AMD's Forum i got the clue to make it 2200+ by increasing the FSB setting from 100 to 133, now it is showing 2200+.
3) i have seen this line in one thread here in this forum that
(* do not install or uninstall any VIA AGP drivers, including those in VIA 4-in-1 drivers...) , if i should not install this driver then will it be OK not installing this driver...?
4) (KT4V BIOS version 1.7 and above fixes the CRC errors (IDE problems that cause crashes) ) , and i have this new motherboard KT4AV with BIOS v( ) ,
but i am having this problem as the system crashes and hangs or blue screen appears and does not support this harddisk, and i have to use a samsung tool to downgrade the UDMA mode of the HDD to 100 MBPS,
(This program will change the UDMA mode of all UDMA 133-supporting Samsung drives in the system)and the samsung says thatthe cause is...
Cause
This issue is caused when the data transfer rate between the motherboard (or host system) and HDD is erroneously set beyond the maximum data transfer capability of host, 100MB/sec. Under this environment, the host system fails to read data correctly from HDD resulting in unsuccessful OS installation.
Please note that this issue is caused by the incompatibility between the motherboard and HDD(s), not by the faulty Samsung hard disk drive.
Now should i have to use my system at 100 MBPS speed as my HDD supports 133 MBPS...?
5) what is the use of the (IrDA Infrared Module Header: JIR1), how can i use it?
6) and the last question is this board has (6-channel software audio codec ), how to use it? ans i don't have the S-Bracket as i did'nt get it with my motherboard, and i want to use the 6 channel output from my PC , please help me how to use it ...
thanks
please help me ,,,,

1) Not sure, see p. 3.
2) Is pretty normal procedure around here.
3) Who on earth might have written that? But I suggest you enter 'Safe Mode' when installing 4-1 drivers. You had better have them.
4) Not sure, see p. 3.
5) Someone must confirm this, but I think its for remote networking.
6) If you have integrated or other sound card, drivers, cables and speakers there is no problem. See the manual, please.

Similar Messages

[VIA] related to msi kt4av (ms 6712) mainboards

hi! I've got a msi kt4av and a few things bother me!
1 the cpu voltage is higher than I set it in windows: I set it to 1.65 but it goes to 1.675 in reality! this goes for all of the voltage values. anyone got this problem?
2 I'd like to buy a new hdd, preferably over 200 gb! on the faq of the board it says that the max supported is 160 gb, but I have doubts it has been updated anywhere recently!
could those of you that have or had this mainboard, help me out a bit? thanks

if a mobo says the max supported HDD size is over 137gb, (eg 160gb) then any size above that (eg 200gb) will work. after the 137gb limit on older boards, the next max size limit i believe is somewhere around 4 terabytes
as for CPU voltage, you should set that in BIOS, and preferably to AUTO, unless you're overclocking and know what you're doing windows utilities don't always read values correctly

NEED HELP..MSI {6712} KT4v-L bios 1.9

First i need help flashing my bios i have 1.8 now
and want 1.9. I am useing xp pro fully updated on an ntsf file format i have no floppy never needed i have a usb 64meg thumb drive . I do not overclock ever ....
I have read several places how to do this but all are a little different so i decided to ask the real pro you guys.
would some one give me a full very detailed description on how i can do this preferbally soemone who has run into the same situation i have any help would be much appreciated.
MSI KT4V-L {6712}
AMD 2400+ {266}
PNY 256 DDR {333}
PNY 5200 DDR FX 128
Creative Audigy 2 Platinum
Sony 16X DVD
Sony DVD-+RW-+
Creative Labs MegaWorks THX 6.1 600 watts
Antec Lanboy
Antec 300 True Power
Thermaltake 3 speed intake
Thermaltake 3 speed exhaust

i had exactly the same problem - na floppy ever needed
1. burn a cd with ami flash or other flash program and your bios file
2. boot the system with your ( in my case windows 98 se ) cd
3. choose to boot with cd-rom
4. run amiflash from your burned cd
5. enjoy !!

Help---MSI KT4AV bios BUG ?!

Hi....(excuse my bad english... ) I try...
I have the MB MSI - KT4AV
two days ago , I have buy a AMD CPU 3200 Ghz , 32bit ofcourse, Inside the shop have sayed to me...no problems with this MB !!!
well I try , but I can't go UP 2800+ !!!
I try and Try with BIOS but no result.
I have read with the last BIOS is corretc the right recognised 3Ghz+ cpu...
I have update BUT always thesame.
So I have read arround, this MB can't support CPU uo 3Ghz !... so never 3,2 ...ok..but MY not go up 2,8 !!!!
BIOS setting....and here is the Myseriuos!!!
FSB...I can't select UP 170 or the PC non start , amnd I must reset the cmos/bios!
(200 I can't forget...I can work with 166.....)
MOLTIPLIC. I can set to x12.13 and My pc (166 - x12.13) give 2800
BUT....If i select x14 I became 880 Mhz !!! and if I set x 15 984 Mhz!!!!!!!
Why ?!?!? this is sure a bios bug....

impossible....sure NEVER He take back!!... later I used and Try.... sure I became in the...A..!
well IF this CPU is not supported WHY work and to 2800 ?!? work or not work....
and WHY x14 give the IDOT nummer 880 Mhz and x15 980 Ghz ? this is ONLY a BIOS problem.... to fixit!!!
so..I not belive MSI have not to do, with this bios...

KT4AV MS-6712 Hang after warm reset

Alright...this one has been bugging me for quite sometime now, but I've always ignored it. I currently have an MSI board: KT4AV MS-6712.
I'm runnin the Athlon 2500+ with a gig of ram. Nothing is overclocked. When I first built the system it worked great. However now anytime I restart it from the Windows shutdown screen or even using the reset switch, the system will hang before the POST has completed and made the beep. It'll come up with all its info showing that its checked the ram and its fine and its detected the hard disks and what not... but then it just hangs. Now if you turn the system off for 1-2 minutes, then turn it back on... it fires right up. No problems at all. I've already updated the BIOS with the latest available from the MSI website. As I said before, I had always just ignored the problem because I never found the time to screw with it. But now I really want to fix this because it is annoying! Um... only other things I have in the unit hardware wise are the following:
TDK 880N DVD Burner
Lite-On DVD Player
WD 30GB HDD
WD 100GB HDD
Radeon 9800 Pro
Audigy 2 Gamer
The D-bracket is also installed.
Anyone have any ideas at all!???
Thanks for your help.

Well actually a full format and clean install of Windows was already performed recently. Also the system has already been cleaned internally. I cannot stand a dirty computer. This is done OFTEN with any machine in my house. Windows having a problem was something I considered though, since it seemed to happen anytime that you would restart from Windows. But its also when you just use the reset switch. And it hangs before the POST is completed. Which makes it seem like it SHOULD be hardware. But its weird because the computer starts up... with the POST screen...not a splash screen. And it goes through all its tests. Such as checking the ram and detecting all the devices and what not. And it gets all the way through everything. The only difference is that it beeps and then boots. It'd be a little easier if it'd hang while detecting and IDE device or whatever ya know? But it doesn't. It appears to fully complete, but it just will hang after a warm reset. I can't remember exactly when it started...it was quite a while ago. However I do not recall making ANY changes to the system when it started. It just started happening. And it used to be that you could turn it off for like 10 seconds, then back on and it'd work Great. Now it seems like you have to wait like a full minute. So I really don't know. I've tried everything I can think of. I've even reduced the unit down to its bare minimum to operate. Still the same. And like I said before I JUST flashed the BIOS like...last night. I was just thinking maybe it was something in it. Still the same. Really running out of options with it. It does work fine though, other than this little annoyance.

MSI KT4AV-L w/ Radeon 9800 Pro at 8x Lockups!

I have the latest 4 in 1 drivers, and the latest Catalyst drivers and it seems that whenever I try running 3DMark2001SE it locks up almost immediately. Now if I use SmartGART to lower my AGP from 8x to 4x it runs flawlessly. Though I can't help feeling that there is some sluggishness in the video. I actually think that my old 4x GeForce 3 Ti500 ran smoother! (I had that on a Soyo Dragon Plus motherboard)
System configuration:
MSI KT4AV-L
Athlon XP 2500+
Radeon ATI 9800 Pro
2 sticks of 256Meg Corsair
60Gig IBM Deskstar
Yamaha 24x CDRW
Cendyne (Pioneer A05) DVD-RW
Antec Sonata case with 380W PS
+5v 35A, +12v 18A, +3.3v 28A, -5v .5A, -12v 1.0A, +5v SB, 2.0A

Quote
If you don't have an actual solution, then please don't post. Thank you for your input.
Not a good way to get help.
Welcome to the world of "new" technology, it takes a little time to get it perfected. As mentioned earlier in the thread, 8X has no perfomance advantage over 4X, and 8X is causing problems, that disappear by using 4X. Until ATI and/or VIA can develop a cure, you have 2 choices:
1. Run 8X mode, and live with the problems.
2. Run 4X mode, and have no problems, and no loss in performance.
(Steps down from soapbox)

AMD-XP 2600+ and MSI KT4V MS-6712 MB

Can somebody help me pls? I do have a MSI KT4V MS-6712 Motherboard and an AMD Athlon XP 2600 processor. According the CPU RATIO settings table I should put the ratio 16 and the FSB on 133, but I don't have a 16. I only have a 15 and if I use the 15 instead of the 16 I do get a performance of 733 Mhz. When I use the 12.5/13 the system says it's a XP-2000+, but I'm still missing some Mhz. I did already upgrade the BIOS to version 1.8 but no results.
Pls help me, I'm getting crazy! ;(

I changed it into 166 Mhz and now it's acting as a XP 2600+.
Rob, thanks for your suggestion and help in this matter.
:P

[VIA] MSI-KT4AV and PC3200 RAM

Hi guys!
I've got an MSI-KT4AV mainboard, an Athlon XP 1800+, and a 512mb 400mhz Pc3200 module. This is the problem: I changed the DDR module from a 512mb 266mhz module to the 512mb 400mhz module; the mainboard has always worked fine with the first type of DDR module, but with the second one, the PC doesn't boot up. I try to change the memory but there is the problem yet. I try also the DDR Module 400mhz on another MSI Mainboard and that mobo function but not the MSI-KT4AV!!!!! I'm sure that this mobo support the DDR Module 400mhz but I don't know why the system doesn't boot up. Another important thing: when I press the power button to switch on the PC, the Display is totally black with no signal but I can clearly hear 3 beeps from the motherboard: BEEP BEEP BEEP silence BEEP BEEP BEEP silence BEEP BEEP BEEP and so on....
Can anyone help me?
Thank you so much for Your reply....

Did you try clearing your CMOS? Look in your mobo manual if you don't know how. That should fix it. :D.
If it still doesnt, put your old stck of memory back in, go into your bios, and look under Frequency and Voltage. Look for Memory voltage/vDimm. Adjust it to 2.7 or 2.8v. Save settings and exit. Wait for windows to boot and shutdown. Then try your new ram again. =D

MSI KT4AV

Hi on the box of a motherboard write that name of mother board is 694T PRO but on Home Everest software name of Motherboard is MSI KT4AV (MSI-6712) (6 PCI, 1AGP, 3 DIMM, Audio). I need lan driver for that mother board?
I have 2 cd's from MSI CD 1CD2

Quote from: BOSSKILLER on 07-November-07, 03:58:50
Please exact ID your mainboard, look here how: https://forum-en.msi.com/index.php?topic=107777.msg798546#msg798546
Have you installed Via 4 in 1, 1st too?

KT4AV MS-6712 v10A No POST

I have ran out of options, tried all posible solutions and still no luck.
The mobo no POST after installing the CPU. If you take out the CPU the board powers up. Tried with different CPUs and had the same result. The board is new as well the CPU.
CPU= AXDA2400DKV3C
Board=KT4AV MS-6712 version 10A
gainward GF4 256 VRAM
256MB RAM kinston 266SDR
bare system
floppy and some no name CD rom
20GB HDD
PSU 400W
PLEASE HELP!!!!
RSK31

I've only heard good about that cooler. When seating it:
-it is normally best to take mobo out of case
-you should with a bit of alcohol and a very clean cloth remove old grease
-put a small drop of new grease on the very die of the processor and spread it out with a credit card or alike
-virtually place the Volcano in the right position
-lean it so you can fasten one of the clams
-without putting too much pressure lean it to the other side so you can fasten the locking clam, (with care use a screwdriver if you are not a stone layer like me).
To get a fresh start I ususally clear CMOS while I'm at it.
...And now that the case is open, you can easily see the sticker with info about your Power Supply Unit, can't you? Top left corner, usually,

MSI KT4AV-L and DDR400

I have a msi kt4av-l mobo, a 512 stick of ddr400 and a athlon xp 2600+ running at fsb 166. the memory stick is only stable when i make it run at 266 mhz, 333 and 400 causes random reboots. so i wonder if anyone can help me get my memory to run stable at 400 like it´s supposed to do

Hello,
You can either overclock the CPU FSB to 200Mhz to match the 400DDR memory,
that will make the memory run at its full potential.
Or
Leave the CPU FSB at the default speed, 166Mhz and underclock the memory to 333DDR.
That way you will get the best system performance possible. You should not overclock the CPU.
Please note that the memory can only run at its full potential if the CPU FSB is the same, 200Mhz FSB and 400DDR memory.
And as you do not have a 200Mhz FSB CPU, running the memory at 400DDR or 333DDR is the same. Due to the CPU FSB.
Did SPD work?

MSI KT4AV no boot issue

I'm having a heck of a time getting my computer to boot back up I get 3 long beeps. This does not match anything I've found for codes. I went back in and installed the D-Bracket 4 LED diagnostic bracket.
This "normally" should show 4 red LED's on boot up. I get 3. The number 1 LED is dead, nothing showing. It then goes to number 2 and 4 red and number 3 green. It stays there and goes through the 3 long beeps.
Is it RAM or is it memory ???
anyone know for sure ??

Well, I was going to post all teh specs...but. I was getting pretty frustrated with it when I "re-set" the power switch on the back of the PWS. I'm running an ANTEC Sonata box and PWS. When I turned the switch off and on at the back I was able to boot up to a point.
I had jumped the CMOS earlier thinking it was the problem. So I had to go back through and reset all the setup config...that done it works like a champ again....
I had reset the Vcard and Memory, no help. I had a guy at a computer store tell me the 2 sticks X 256 were not compatiable and that was causing the trouble. He was a little perplexed when I told him it had ran like that for months....He did want me to bring the box in so he could fix it....wonder what that would have cost ?? I guess if you replace enough parts it will work...
Bottom line : 3 lond beeps with a MSI KT4AV board VIA chipset and ANTEC PWS try turning it off and on at the back...worked for me.
Never was able to find an actual listing for those 3 long beeps...

What's happened to my board? (MSI KT4AV-L)

I have a bit of a problem,
I have a MSI KT4AV-L with a AMD Athlon XP3000+ Processor.
Here's the mail i've just sent to the tech support of where I got the board from..
Quote
Yesterday, I started to have problems with the internal network port - it was not finding the my gateway, however when I tried the exact same cable and router port on my laptop, it all worked fine.
I decided to reformat and re-install windows XP, in case it was a software error, however this still didn't solve it. The basic problem was that I was getting Timeouts - I tried pinging the router and it was a mixture of successes and failures.
I went into the BIOS and changed back to "Default" settings and restarted - this has made matters worse - now my Graphics card is not working correctly and i'm not able to see anything on the monitor at all due to this.
These facts have made me feel that the Motherboard kid is faulty - I also noticed that the XP3000 chip I had was only showing up in windows as a 1.9ghz processor - not sure if this is correct or not.
Do you have any suggestions or can you give me a manufacture contact so I can try and resolve this issue without needing to send it back - I would appreciate a quick reply as I use this machine for work and it is causing me to delay some freelance projects that I am working on.

Hello,
Did they get back to you?
Please make a list of all your components, including the power supply + details of the sticker.
eg,
+12v = 10a
+5v = 20a
XP3000+ is 2.16Ghz
You need to enter the BIOS and set the FSB to 166Mhz.
Press DEL when you turn the PC on or restart,
go to Frequency/Voltage control > press enter
FSB > press enter, change it to 166Mhz. >press enter
press escape, then goto save and exit > Y > press enter
So that is one problem out of the way.
GFX card problem, is your card AGP 4x or 8x?
Now would be a good time to post that list

MOVED: Need help with msi mega 180 + athlon xp-m combo

This topic has been moved to Overclockers & Modding Corner.
Need help with msi mega 180 + athlon xp-m combo

AFAIK, you shouldn't need a pinmod for a Mobile Athlon XP CPU to work in a nforce2 mobo
did you have any other CPU installed prior to this one? if so, refer here to clear the CMOS: Clear CMOS Guide
next, refer to your manual, or download from MSI, for location of the FSB jumpers; ensure J8 is shorted across pins 1-2, and J7 is shorted
finally, enter your BIOS setup menu, and under Advanced Chipset Features, set CPU FSB to 133mhz (or even 166mhz if you have DDR333 memory). the only thing i can't see in the Mega 180 manual is where you set the multiplier...
which is where the BIOS has limited overclocking features, and you might have a problem here
i think i'll pass this over to the Overclockers forum, where someone may be able to give a better answer....

Advice on how to put Vista on KT4AV MS-6712 1.0A

People, How are you!!
Well in an old post I put this topic: "What kind of memory and CPU put in my..."
So i liked to install windows vista, I live in costa rica so now I want to change the following components..
Old Config:
CPU: AMD ATHLON XP 2000+ (1.67Ghz)
PSU specs: Omega 480W
+3.3V: 30A
+5V: 38A
+12V: 22A
+5 VSB: 2.0A
-5V: 0.5A
-12V: 1.0A
HDD: Western Digital 40GB
MEM: 2X 256MB Kingston DDR266
MOBO: MSI KT4AV (latest drivers of 2006)
VIDEO: MSI NVIDIA GFORCE 4MX 440 AGP 8X 64MB (Prince of Persia I doesn´t work in this one)
So i like to know opinions and kind of cards.... in a modest budget..
TKS!!!
All I want is test Windows Vista Ultimate and Play Doom III in this one.. so... only a new machine right??

Vista will cost you half a new system.
I don't think you should have a SocketA motherboard, at all, so yes, a new system.
If you don't buy a massive graphics card, you should be able to keep your PSU, and maybe you can keep your case, I don't know.
Here is an idea:
AMD Athlon 64 X2 4200+ 2.2GHz Socket AM2 1MB, BOXED m/fläkt
Corsair Value S. PC5300 DDR2 1024MB Kit w/two matched Value Select 512MB
MSI K9N NEO-F, nForce 550, Socket-AM2, SATAII, DDR2, GbLAN, ATX, PCI-Ex16
PCI-Express graphics card I'm not so good at, but I like ATI cards.
It is not too expensive, but if you have some money spend some more on the memory.

Help on MSI KT4AV(MS-6712)

Similar Messages

Maybe you are looking for