Help: Port forward in Cisco SOHO 97

Hi there!
I have a Cisco SOHO 97.
The IP is: 10.0.0.1/24
Gw: 0.0.0.0
*Default route via DIALER1
I also have a RV042 configured as VPN Server (PPTP and IPSec).
The IP is: 10.0.0.2/24
I need help to configure the router to I be able to connect to VPN server from OUTSIDE-WORLD.
I imagine I need Port forwarding from Cisco SOHO to RV042.
I hope for possibles answers!
Thanks!

Sorry i found the issue.
The problem was that, i wanted to redirect port 443 (https) to an private address.
But by default port 443 is reserved to access ASA via https for management.
I just reserved another port 888 for https management access and now i can redirect port 443 normaly as i wanted.
Using this command: http server enable 888
Germain

Similar Messages

Help Port Forwarding

I have an VersaLink Model 7500 and i need help port forwarding so i can play on Xbox Live i need to have an Open NAT and port forward could some one assit me?
Message Edited by Canquain on 08-20-2009 10:24 AM

#1 Check the IP Address, Subnet Mask, Default Gateway and DNS Servers on your computer.
As how to do, for example if on Windows XP...
a) Go to Start -> Run.
b) Type in
cmd
and press enter.
c) In the new window, called the command prompt, type in
ipconfig /all
and press enter.
#2 With your web browser go to the default gateway, and log-in as need be.
#3 Show the first screen that you see, in your router.
If you are the original poster (OP) and your issue is solved, please remember to click the "Solution?" button so that others can more easily find it. If anyone has been helpful to you, please show your appreciation by clicking the "Kudos" button.

Lost ability to connect through port forwarding after cisco guest software install

Using Remote Admin 2.2 software to remote into work computer.
E1000 I installed the cisco guest software on my pc and configured the guest about 2 months ago.
Needed to get into office PC this past weekend and connection fails.
Have a static IP address on router. forward a single port to my office machine within the router.
Get nothing but an error on connection. Router is 2.1.02 build 6Jan 15, 2013.
Log file shows nothing on the incoming log? dynamic ip at home...
Another office worker, on the same internal network, has gotomypc running and port forwarding setup on router and he is still working fine, he can access his pc from home. The only change I have made to router was the cisco connect for guest access.
Is it possible this is stopping my remote admin?
thanks kevin

Hey kevboac! Make sure that the computer you're using to access the remote computer is connected to the main wireless network and not to the Guest network. Being connected to the Guest network will prevent you from doing File and Printer Sharing, and Remote Access. Hope this helps!

Port Forwarding for Cisco ASA 5505 VPN

This is the Network
Linksys E2500 ---> Cisco ASA 5505 ---> Server
I beleive I need to forward some ports to the asa to use the IPsec VPN I just setup. I had the SSL VPN working but only needed to forward 443 for that....I assume that IPsec tunnel is a specific port.
Thank You

For IPSec VPN, you need to port forward UDP/500 and UDP/4500, and remember to enable NAT-T on the ASA.
Command to enable NAT-T on ASA:
crypto isakmp nat-traversal 30

Port Forward in Cisco series 800

Dear Support
below the configuration of Cisco Series 800 Router that Has VDSL port of internet , the configuration as below :
i add three command
what is required in order to make port forward
ip nat inside source static tcp 8000 10.10.10.10 8000 dilar 0
ip nat inside source static tcp 554 10.10.10.10 554 dilar 0
ip access list extended 100
permit ip any any
what is required to make port forward to the local ip address 10.10.10.10 from outside interface that is VDSL port ?
! Last configuration change at 10:47:44 KSA Wed Apr 22 2015 by aamalsup
version 15.2
no service pad
service timestamps debug datetime msec
service timestamps log datetime
service password-encryption
hostname AamalNet
boot-start-marker
boot-end-marker
logging buffered 51200 warnings
enable secret level 2 5 $1$Y4PF$K6TQ5wf0gcHiO5IxvLZba0
enable secret level 5 5 $1$WZeO$BzTCl0C0e1078CWxExJK0/
enable secret 5 $1$plq6$P5HVL/tR81cs0GFDrD.0V/
aaa new-model
aaa authentication login default local
aaa authentication login sdm_vpn_xauth_ml_1 local
aaa authentication login sdm_vpn_xauth_ml_2 local
aaa authorization exec default local
aaa authorization network sdm_vpn_group_ml_1 local
aaa session-id common
clock timezone KSA 3 0
crypto pki trustpoint TP-self-signed-1682106276
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-1682106276
revocation-check none
rsakeypair TP-self-signed-1682106276
crypto pki certificate chain TP-self-signed-1682106276
certificate self-signed 02
30820250 308201B9 A0030201 02020102 300D0609 2A864886 F70D0101 04050030
31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274
69666963 6174652D 31363832 31303632 3736301E 170D3032 30333031 30303038
35315A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649
4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D31 36383231
30363237 3630819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281
8100C2F3 49897460 71FEB259 7794B7C6 D398958A 2D338F0F C69F0E75 1137B16C
C261A275 8416DAF6 FC19AA6E 50024019 66CE4DB8 3AFAB6FE CE892B42 86A93490
97259E47 D740B2F4 9AA2D307 7B676841 2CAAA879 D945A6FD 717B507F 77399332
1644CEDE 884BF133 ACFBBC80 9869A104 54CC3EEE 9D521378 EC762D86 C3F0ABC9
CA990203 010001A3 78307630 0F060355 1D130101 FF040530 030101FF 30230603
551D1104 1C301A82 18417761 6C416D61 6C792E61 77616C6E 65742E6E 65742E73
61301F06 03551D23 04183016 80149ADD A651C9F9 F8369354 5C904777 090FEB75
72E0301D 0603551D 0E041604 149ADDA6 51C9F9F8 3693545C 90477709 0FEB7572
E0300D06 092A8648 86F70D01 01040500 03818100 50ACCA98 1A5FCCAD FC61D703
A8589B02 AFB8CD47 BD1CC7B0 B095C97F AA0604A8 F8495053 C8A9CBB9 644F5674
318A7AA0 873250AD 1DE28CE2 BE21ED19 BF212CF7 E2A97CFB FFA62F1E 643CEDFE
90D02109 719FD4D3 98E6C40B D61CE89C D2426C1E 3CBD9FBE 397F7F7C F1DD279E
14F8BB2D ABFA784B 6E04274B EDCBFC8F A805E91D
    quit
ip cef
no ip dhcp use vrf connected
ip dhcp excluded-address 10.10.10.1
ip dhcp excluded-address 10.10.11.1
ip dhcp pool lan
import all
network 10.10.10.0 255.255.255.0
default-router 10.10.10.1
dns-server 212.93.192.4 212.93.192.5
lease 0 2
ip dhcp pool wireless
import all
network 10.10.11.0 255.255.255.0
default-router 10.10.11.1
dns-server 212.93.192.4 212.93.192.5
lease 0 2
no ip domain lookup
ip domain name aamal.net.sa
ip name-server 212.93.192.4
ip name-server 212.93.192.5
no ipv6 cef
cwmp agent
enable download
enable
session retry limit 10
management server password 7 094D4308151612001D05072F
management server url http://aamalservice.aamal.net.sa:9090
license udi pid C887VA-W-E-K9 sn FCZ17459018
archive
log config
hidekeys
username k privilege 15 password 7 020D
username admin privilege 15 password 7 14161606050A
controller VDSL 0
crypto isakmp policy 1
encr 3des
authentication pre-share
group 2
crypto isakmp client configuration group aamalnet
key aamalnet
dns 212.93.192.4 212.93.192.5
include-local-lan
dhcp server 10.10.10.1
max-users 10
netmask 255.255.255.0
crypto isakmp profile sdm-ike-profile-1
   match identity group aamalnet
   client authentication list sdm_vpn_xauth_ml_2
   isakmp authorization list sdm_vpn_group_ml_1
   client configuration address respond
   virtual-template 1
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
mode tunnel
crypto ipsec profile SDM_Profile1
set security-association idle-time 60
set transform-set ESP-3DES-SHA
set isakmp-profile sdm-ike-profile-1
bridge irb
interface ATM0
no ip address
no atm ilmi-keepalive
interface ATM0.1 point-to-point
pvc 0/35
pppoe-client dial-pool-number 1
interface Ethernet0
no ip address
shutdown
interface FastEthernet0
no ip address
interface FastEthernet1
no ip address
interface FastEthernet2
no ip address
interface FastEthernet3
no ip address
interface Virtual-Template1 type tunnel
ip unnumbered Dialer0
tunnel mode ipsec ipv4
tunnel protection ipsec profile SDM_Profile1
interface Wlan-GigabitEthernet0
description Internal switch interface connecting to the embedded AP
switchport mode trunk
no ip address
interface wlan-ap0
description Embedded Service module interface to manage the embedded AP
ip unnumbered Vlan1
interface Vlan1
description $ETH-SW-LAUNCH$$INTF-INFO-HWIC 4ESW$
ip address 10.10.10.1 255.255.255.0
ip nat inside
ip virtual-reassembly in
ip tcp adjust-mss 1452
interface Vlan2
no ip address
bridge-group 2
interface Dialer0
ip address negotiated
ip mtu 1452
ip nat outside
ip virtual-reassembly in
encapsulation ppp
dialer pool 1
dialer-group 1
ppp authentication chap callin
ppp chap hostname [email protected]
ppp chap password 7 0007145E2E5A05522E1858
no cdp enable
interface BVI2
ip address 10.10.11.1 255.255.255.0
ip nat inside
ip virtual-reassembly in
ip forward-protocol nd
ip http server
ip http access-class 23
ip http authentication local
ip http secure-server
ip http timeout-policy idle 60 life 86400 requests 10000
ip nat inside source list 1 interface Dialer0 overload
ip route 0.0.0.0 0.0.0.0 Dialer0
access-list 1 remark SDM_ACL Category=2
access-list 1 permit 10.10.10.0 0.0.0.255
access-list 1 permit 10.10.11.0 0.0.0.255
access-list 23 permit 212.93.196.0 0.0.0.255
access-list 23 permit 212.93.192.0 0.0.0.255
access-list 23 permit 212.93.193.0 0.0.0.255
access-list 23 permit 10.10.10.0 0.0.0.255
access-list 23 permit 10.10.11.0 0.0.0.255
dialer-list 1 protocol ip permit
no cdp run
snmp-server community private RW
snmp-server community public RO
bridge 1 protocol ieee
bridge 1 route ip
bridge 2 protocol ieee
bridge 2 route ip
privilege interface level 5 encapsulation
privilege interface level 5 description
privilege interface level 5 no encapsulation
privilege interface level 5 no description
privilege interface level 5 no
privilege configure level 5 ip route
privilege configure level 5 interface
privilege configure level 5 controller
privilege configure level 5 ip
privilege exec level 5 copy running-config tftp
privilege exec level 5 copy running-config
privilege exec level 5 copy
privilege exec level 5 write memory
privilege exec level 5 write
privilege exec level 5 configure terminal
privilege exec level 5 configure
privilege exec level 5 show processes cpu
privilege exec level 5 show processes
privilege exec level 2 show running-config
privilege exec level 5 show configuration
privilege exec level 2 show
privilege exec level 5 clear counters
privilege exec level 5 clear
banner exec
CC
% Password expiration warning.
Cisco Router and Security Device Manager (SDM) is installed on this device and
it provides the default username "cisco" for one-time use. If you have already
used the username "cisco" to login to the router and your IOS image supports the
"one-time" user option, then this username has already expired. You will not be
able to login to the router with this username after you exit this session.
It is strongly suggested that you create a new username with a privilege level
of 15 using the following command.
username <myuser> privilege 15 secret 0 <mypassword>
Replace <myuser> and <mypassword> with the username and password you want to
use.
banner login
CC
********STC AamalNet Service****************************************
********Authorize Access Only. For more Support Call 909************
line con 0
privilege level 15
no modem enable
line aux 0
line 2
no activation-character
no exec
transport preferred none
transport input all
stopbits 1
line vty 0 4
access-class 23 in
privilege level 2
transport input telnet ssh
scheduler max-task-time 5000
scheduler allocate 20000 1000
end

Hello,
Sure.
What version are you running?
Regards,

How to Port Forward on Cisco 1900 Router?

We have a cisco 1900 router. I m new to cisco routers commands, recently started learning. I need to forward all requests coming from port 1723 from outside to inside server ip. I check "show running-config" and I see already forwarded ports and ip like below,
ip nat pool onlyone xxx.xxx.xxx.xxx xxx.xxx.xxx.xxx netmask 255.255.255.252
ip nat inside source list 1 pool onlyone overload
ip nat inside source static tcp 192.168.0.xx 22 xxx.xxx.xxx.xxx 22 extendable
ip nat inside source static tcp 192.168.0.xx 80 xxx.xxx.xxx.xxx 80 extendable
ip nat inside source static tcp 192.168.0.xx 80 xxx.xxx.xxx.xxx 96 extendable
ip nat inside source static tcp 192.168.0.xx 443 xxx.xxx.xxx.xxx 443 extendable
ip route 0.0.0.0 0.0.0.0 xxx.xxx.xxx.xxx
where xxx.xxx.xxx.xxx is public facing IP.
so what is the command to add "ip nat inside source static tcp 192.168.1.xx 1723 <public-ip> 1723 extendable" to currnetly working settings?
I am currently reading below but no luck so far...
http://www.cisco.com/en/US/docs/routers/access/1900/software/configuration/guide/software_configuration.pdf
I have found this
http://www.cisco.com/en/US/tech/tk648/tk361/technologies_tech_note09186a0080094e77.shtml#topic7
interface ethernet 0
ip address 172.16.10.1 255.255.255.0
ip nat inside
!--- Defines Ethernet 0 with an IP address and as a NAT inside interface.
interface serial 0
ip address 200.200.200.5 255.255.255.252
ip nat outside
!--- Defines serial 0 with an IP address and as a NAT outside interface.
ip nat inside source static tcp 172.16.10.8 8080 172.16.10.8 80
!--- Static NAT command that states any packet received in the inside
!--- interface with a source IP address of 172.16.10.8:8080 is
!--- translated to 172.16.10.8:80.
How do I know if "interface ethernet 0" and "interface serial 0" will work for me?

the router is already setup and working for 2 years. all i need to do add a simple port forward from public ip to internal server. Following make sense to accomplish what i m trying to do. Lets assume 1.2.3.4 is my office public static ip and 192.168.0.10 is my internal server. All requests will come from some Ip lets say 25.24.23.22:1723 to 1.2.3.4:1723 and router will forward this request to 192.168.0.10:1723. This is all i m trying to accomplish. I m not setting up a new router. Some rules are already there. Therefore below seem to be what i need. All I need is how to identify "interface ethernet 0" & "interface serial 0". I understand the inside and outside details. All i have to find is how to replace ethernet 0 and serial 0 with what i have in my router setup.
interface ethernet 0
ip address 172.16.10.1 255.255.255.0
ip nat inside
!--- Defines Ethernet 0 with an IP address and as a NAT inside interface.
interface serial 0
ip address 200.200.200.5 255.255.255.252
ip nat outside
!--- Defines serial 0 with an IP address and as a NAT outside interface.
ip nat inside source static tcp 172.16.10.8 8080 172.16.10.8 80
!--- Static NAT command that states any packet received in the inside
!--- interface with a source IP address of 172.16.10.8:8080 is
!--- translated to 172.16.10.8:80.

Help Port Forwarding My playstation 3!

My Router: WRT54GS
Well, I have already finished opening all the ports on the routers main page, but I have absolutely no idea what to do next!
I opened or forwarded like 8 Ports, so it would be much more compatible with my PS3 and online gaming, but I don't know what to do next! I made a static IP, but I've been hearing that you need to assign a static IP to the PS3. How exactly do I do that? What IP address should I assign my PS3?

Don't use the IP Address assigned to the computer, instead use a different(unique) IP Address(like 192.168.1.60) for your Play Station...While Port Forwarding on your router you should make sure to open the Ports for the static ip address used on your Play Station...

Help port forwarding my WRT54GS

When I go to 192.168.1.1, Internet Explorer alerts me that the page has an error, I look down to see most of the text and images missing on the page. Once I finally get to the port forward section, there were no "apply" or "accept" buttons. If anyone could tell me how to fix this I would be greatly appreciative. ~~Thanks, ~~Brendon

Download and run the tftp.exe utility from the linksys ftp site.
Richard Aichner (Ikester)

Port Forwarding for Cisco camera WVC80N and AirPort Extreme

I have set up my camera to the Apple AirPort Extreme on a Windows 8 computer, but now get an error saying, "The setup wizard cannot set up TZO DDNS with your network for remote viewing." After clicking on the Learn How to Remotely View my Camera, it suggests I need to get Port Fowarding for my router" And iot suggests my router password is incorrect which it is not. Any help for a BEGINNER would be appreciated. I cannot find the IP address for the camera or my computer either.
Cisco support is NO help at all. ANY help would be appreciated. PLEASE MAKE IT SIMPLE. I can set it up on my MAC desktop also if that is better. Thanks so much

gnsmith wrote:
I have a D-Link DCS-920 I would like to view over the internet using my Airport Extreme.
Welcome to Apple's discussion groups.
According to the manual for that device (available here
ftp://ftp.dlink.com/Multimedia/dcs920/Manual/dcs920manual100.zip
you should set the port number that the camera uses to something other than port 80. You'd then use AirPort Utility (the "Advanced" panel, "Port Mapping" tab) to map that TCP port and the camera's "private IP address" to a public TCP port. (I'm not sure what to use for "Service". You might try "Personal Web Sharing". It may also not matter once you chance the port number.) You'll need to know the WAN ("public") IP address of your AirPort Extreme. With that done you should be able to view the camera at that WAN IP address and the declared public port.

Need help port forwarding on A1264 Airport Express

Hey, I am having some trouble forwarding a port.
I have followed guides online,
My OS is Windows 7
1) I created a static ip for my computer 10.0.1.151
2) Went into Airport Utility, Under Internet > DHCP tab I clicked "+", used my computers mac address, and used 10.0.1.151 for the IPv4 feild.
3) Went to Advanced > Port Mapping, clicked "+" typed in the TCP port i want forwarded, and typed 10.0.1.151 in for private IP feild.
Everytime I test to see if the port is open using this site:
http://www.yougetsignal.com/tools/open-ports/
It says the port is closed.
Is there something I'm doing wrong?
Any Help is apprecieted
Thanks

I assigned a static ip to my ps3 and set these ports up and my NAT type is open.

Help ( Port ForWarding ) SOLVED

Hello Well i need help tryin to open a port on my router so i can host a Game Server From my pc i could do it by my self but i dont know my verizon router panel info i think some one has changed my password or something Pls help me
Message Edited by MH1957 on 07-28-2009 03:22 PM
Message Edited by MH1957 on 07-28-2009 03:58 PM
Solved!
Go to Solution.

the default login to the router is usually either admin / password or admin / password1
If neither of these work, just press the reset button on the back for about 10 seconds and then when the router boots back up it will default back to admin / password
Oh, BTW, Just in case, the IP to log into the router is 192.168.1.1 just in case you didnt already have that
Message Edited by spacedebris on 07-28-2009 03:51 PM
====================================================================================
Error exists between keyboard and chair.

Port Forward Config Cisco 1841

I am trying to have my domain (jjkkcc.org) get directed to my server from my Cisco 1841. I have godaddy DNS configured to my static IP to my router, and I just want to make sure I have my router configured correctly so the WWW traffic is passed to my web server (192.168.1.250).
Cisco1841#show run
Building configuration...
Current configuration : 1715 bytes
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname Cisco1841
boot-start-marker
boot system usbflash0:c1841-advipservicesk9-mz.124-12.bin
boot-end-marker
no aaa new-model
clock timezone PSD -8
ip cef
ip domain name jjkkcc.com
ip name-server 68.105.28.16
ip name-server 68.105.29.16
ip name-server 8.8.8.8
ip name-server 8.8.4.4
ip name-server 192.168.1.250
username woodjl1650 privilege 15 password 0 henry999
interface FastEthernet0/0
ip address 192.168.1.6 255.255.255.0
ip nat inside
ip virtual-reassembly
duplex auto
speed auto
interface FastEthernet0/1
ip address 24.234.XXX.XXX 255.255.255.224
ip nat outside
ip virtual-reassembly
duplex auto
speed auto
ip route 0.0.0.0 0.0.0.0 24.234.XXX.XXX
no ip http server
no ip http secure-server
ip nat inside source list NAT interface FastEthernet0/1 overload
ip nat inside source static tcp 192.168.1.250 80 interface FastEthernet0/1 80
ip nat inside source static tcp 192.168.1.10 3074 interface FastEthernet0/0 3074
ip nat inside source static udp 192.168.1.10 3074 interface FastEthernet0/0 3074
ip access-list standard NAT
permit 192.168.1.0 0.0.0.255
ip access-list extended WEB
permit tcp any any eq www
snmp-server community public RW
snmp-server trap link ietf
snmp-server location Las Vegas, NV, USA
snmp-server contact Jonathan Wood - Network Admin
snmp-server chassis-id Cisco1841-Router
snmp-server host 192.168.1.155 version 2c public
control-plane
line con 0
line aux 0
line vty 0 4
login local
transport input ssh
scheduler allocate 20000 1000
end

These two lines look incorrect because of the interface:
ip nat inside source static tcp 192.168.1.10 3074 interface FastEthernet0/0 3074
ip nat inside source static udp 192.168.1.10 3074 interface FastEthernet0/0 3074
F0/0 is your lan interface. Wouldn't you want those attached to fa0/1?
HTH,
John
*** Please rate all useful posts ***

Cisco ASA 5512, IP NVR port forwarding

Hi,
i have Cisco 5512 ASA with version 8.6(1)2. i have one IP NVR for ip cameras.
please help me how to configure port forwarding in cisco asa in CLI?
I have static IP on ASA 94.56.178. 222 and NVR IP 10.192.192.100
thank you so much.

ASA#
Phase: 1
Type: ROUTE-LOOKUP
Subtype: input
Result: ALLOW
Config:
Additional Information:
in 94.56.178.222 255.255.255.255 identity
Phase: 2
Type: ACCESS-LIST
Subtype:
Result: DROP
Config:
Implicit Rule
Additional Information:
Forward Flow based lookup yields rule:
in id=0x7fffa2969000, priority=0, domain=permit, deny=true
hits=11524, user_data=0x9, cs_id=0x0, use_real_addr, flags=0x1000, protocol=0
src ip/id=0.0.0.0, mask=0.0.0.0, port=0
dst ip/id=0.0.0.0, mask=0.0.0.0, port=0, dscp=0x0
input_ifc=OUTSIDE, output_ifc=any
Result:
input-interface: OUTSIDE
input-status: up
input-line-status: up
output-interface: NP Identity Ifc
output-status: up
output-line-status: up
Action: drop
Drop-reason: (acl-drop) Flow is denied by configured rule
please advise

RVS4000 Port Forwarding not working

I am trying to forward ports through my RVS4000 however I have been unable to get it to work.
I have enabled the firewall and set the ports mapping to the correct address and enabled them, however I can't reach any devices.
All advice gratefully received :>)
NM

When troubleshooting Port forwarding on any device we use tools like Nmap on a outside machine looking in at your network, and http://www.canyouseeme.org/ to see if on the server or device you are using if the outside world can see the ports open. There is no known bug or issue with port forwarding on this device as long as you are on the latest firmware. If Nmap and canyouseeme is not showing the ports open you need to look at the internal workings of the network. I.E. does the same ports work on the inside of your network, second is what is between the RVS4000 and the Internet. Other routers or switches, Modem, and ISP. We have seen everyone of the previous devices block ports. When using Nmap or canyouseeme the ports should be open.
Do you have a topology of your network and what ports you are trying to port forward?
Cisco Small Business Support Center
Randy Manthey
CCNA, CCNA - Security

HELP!! Cisco RV180 Port Forwarding

Someone please advise as to this is the first time I've tried to setup port forwarding using the Cisco RV180 Router. I have a Cisco RV180 Router, a Ruckus 7055 access point and a power distribution unit. I'd like to be able to access the router remotely and also the devices behind the router (the ruckus access point and the power distribution unit). I'm assuming that I'll need to assign the Cisco RV180 router a static IP address and I'm assuing that this static address should be assigned to the WAN port? I'd also like to configure port forwarding so that I can access the ruckus and the PDU remotely also. I've tried assigning a static IP address to the WAN port of the RV180 but I cannot ping this device remotely. Anyone have any advice on accessing the RV180 remotely? I've populated all of the correct fields for the WAN settings (ip, gateway, subnet, etc.) , and my static ip address is valid.Thank you in advance.

Hello sirflex,
As you have mentioned you need to configure a static nat for the devices which you have done when you configure a port forwarding.
Have you configured access rules under firewall>access Rules. Add the access rules for the ping and the Http and Https services.
Can you capture the packets at the WAN port while you are pinging the WAN port and the firmware version on the device.
Which mode are you running the device gateway or router. You can check it under Netwroking>Routing>Routing Mode.
Thanks,
Prithvi
Please mark answered and rate for helpful posts.

Help: Port forward in Cisco SOHO 97

Similar Messages

Maybe you are looking for