HELP !!! Powermac is NOT starting
Hi Powermac users, awoke this morning to find that my powermac G5 first gen. Dual 2Ghz is not booting power button light lights up then off do hear relay clicks from the powersupply when the power button it pressed and also when the powercord is installed and removed. After a few click of the power button I now smell something burning ie electronic smell. Removed all but one memory stick reset PMU or SMT near memory bank. Changed PRAM battery to new. No help thinking powersupply and or logicboard/processor failure.
Any help will be greatly appreciated.
Jim
Hi Jim,
Could be bad RAM, bad power supply or a bad power switch or connection. I would start by removing all RAM, leaving only the Apple supplied RAM and reboot to see what happens. Also, there is cable of wires leading from the logic board to the power switch, located on the lower left. Check these connections.
My guess is a failed RAM chip.
Best Regards
Similar Messages
-
(10.1.3.0.4) Help System does not start
For some reason my help system does not start when selecting from the menu. "Table of contents" or "index" options do nothing. It use to work fine. Conext sensitive help works okay by pressing F1.
Any ideas?Hi paulfrench, check your documentation settings
Menu Tools -> Preferences -> Documentation
Make sure you have checked all of them.
Luis R. -
HELP: I can not start Photoshop
Today he appeared a strange problem with Photoshop CS4. When I boot window appears with the license agreement (which did not before) I give to accept and close the window.
Nothing more, Photoshop will not start. I am desperate because I did not figure the solution.
Can you help?What OS do you have? Go to Start, start search, type in MSconfig. Click on MSconfig, startup and ensure Adone CS4 Service manager is checked.
Also try trashing your Prefs by either the keyboard or the manual way by reading this:
http://forums.adobe.com/thread/375776?tstart=0 -
my imac is not starting up. when i turn on the computer, i get a blue screen with a blinking folder icon of the finder and a black question mark. i can't move anything or type anything.
i have tried powering down and powering back up with holding down the option key, but all i get is a screen with two buttons with a curved arrow and a straight arrow. however, i can't click any of them!
i don't know what to do and i need major help! can anyone help me? i don't want to spend the $49 again for a simple fix.For starters, follow the steps in this Apple KB Article Post back if you have any questions or things still don't work out.
Clint -
Help, OracleDBConsoleasdb could not start after rebooting of server.
We have Oracle AS 10g R2 with infrastructure and portal. What can I do?
Mbw
ElenaWhich of them?
F.exp. Oracleim1ASControlsrvc.log contain:
01/14/08 06:04:05 Recieved ServCtrlHdlr command, 5
01/14/08 06:04:05 Stopping iasconsole
01/14/08 06:04:05 Launching stop EMD process...
01/14/08 06:04:06 Waiting for stop EMD process to exit. numRetries=74
01/14/08 06:04:11 Waiting for stop EMD process to exit. numRetries=73
01/14/08 06:04:16 Waiting for stop EMD process to exit. numRetries=72
01/14/08 06:04:16 Stop process has exited with exitCode: 0
01/14/08 06:04:16 Waiting for emwd process to exit. numRetries=74
01/14/08 06:04:16 Watchdog process exited with exit code -1
01/14/08 06:04:16 Signal Shutdown event.
01/14/08 06:04:16 Shutdown thread exited.
01/14/08 06:04:16 ServiceMain wake up by ShutdownProc, emwd has exited. ServiceMain exits
-------------- [Oracleim1ASControl] ------------
EMDROOT=D:\oracle\im
ORACLE_HOME=D:\oracle\im
EMDSTATE=D:\oracle\im
CONSOLE_CFG=iasconsole
TRACE_LEVEL=16
TIMEOUT=15
01/14/08 06:04:56 Start pending...
01/14/08 06:04:56 Verifying iasconsole is not started already. Command line "D:\oracle\im\bin\emctl.bat" istatus iasconsole
01/14/08 06:05:00 iasconsole launch commandline is "D:\oracle\im\bin\emctl.bat" istart iasconsole
01/14/08 06:05:00 Tracking process launch...
01/14/08 06:05:33 Received exitCode 1 from emctl istatus
01/14/08 06:05:43 Did not hear back from emctl istatus.
01/14/08 06:05:43 Waiting a further 5 secs...
01/14/08 06:05:48 Did not hear back from emctl istatus.
01/14/08 06:05:48 Waiting a further 5 secs...
01/14/08 06:05:53 Did not hear back from emctl istatus.
01/14/08 06:05:53 Waiting a further 5 secs...
01/14/08 06:05:58 Did not hear back from emctl istatus.
01/14/08 06:05:58 Waiting a further 5 secs...
01/14/08 06:06:04 Did not hear back from emctl istatus.
01/14/08 06:06:04 Waiting a further 5 secs...
01/14/08 06:06:09 Did not hear back from emctl istatus.
01/14/08 06:06:09 Waiting a further 5 secs...
01/14/08 06:06:14 Did not hear back from emctl istatus.
01/14/08 06:06:14 Waiting a further 5 secs...
01/14/08 06:06:19 Did not hear back from emctl istatus.
01/14/08 06:06:19 Waiting a further 5 secs...
01/14/08 06:06:24 Did not hear back from emctl istatus.
01/14/08 06:06:24 Waiting a further 5 secs...
01/14/08 06:06:29 Did not hear back from emctl istatus.
01/14/08 06:06:29 Waiting a further 5 secs...
01/14/08 06:06:34 Did not hear back from emctl istatus.
01/14/08 06:06:34 Waiting a further 5 secs...
01/14/08 06:06:39 Did not hear back from emctl istatus.
01/14/08 06:06:39 Waiting a further 5 secs...
01/14/08 06:06:44 Did not hear back from emctl istatus.
01/14/08 06:06:44 Waiting a further 5 secs...
01/14/08 06:06:49 Did not hear back from emctl istatus.
01/14/08 06:06:49 Waiting a further 5 secs...
01/14/08 06:06:54 Did not hear back from emctl istatus.
01/14/08 06:06:54 Waiting a further 5 secs...
01/14/08 06:07:00 Did not hear back from emctl istatus.
01/14/08 06:07:00 Waiting a further 5 secs...
01/14/08 06:07:05 Did not hear back from emctl istatus.
01/14/08 06:07:05 Waiting a further 5 secs...
01/14/08 06:07:10 Did not hear back from emctl istatus.
01/14/08 06:07:10 Waiting a further 5 secs...
01/14/08 06:07:15 Did not hear back from emctl istatus.
01/14/08 06:07:15 Waiting a further 5 secs...
01/14/08 06:07:20 Did not hear back from emctl istatus.
01/14/08 06:07:20 Waiting a further 5 secs...
01/14/08 06:07:25 Did not hear back from emctl istatus.
01/14/08 06:07:25 Waiting a further 5 secs...
01/14/08 06:07:30 Did not hear back from emctl istatus.
01/14/08 06:07:30 Waiting a further 5 secs...
01/14/08 06:07:32 Received exitCode 3 from emctl istatus
01/14/08 06:07:32 iasconsole started -
(Urgent - Please Help) E3500 Can not started up
Dear Sun Experts:
Please could you help me for the E3500; the system is at the moment can not bring up to service.
My E3500 has a major problem and the system has automatically reboot itself.
Afterwards; the below error messages has popped up.
md 101 : /dev/dsk/c2t4d0s0 need maintenance
metainit somcsys3: stale databases.
Insufficient metadevice database replicas located, use metadb to delete database which are broken.
I use the fsck tried to fix the /dev/dsk/c2t4d0s0 and after fixed, I tried to start up the E3500 but found the problem:
Enter Run Level: 0-6 , s , S
I have enter 6 put the E3500 refuse to start up and with the following messages:
INIT: Can not create /var/adm/utmp or /var/adm/utmpx
INIT: SINGLE USER MODE
My E3500 is equipped with 8 x 9 Gb harddisk with 4 system and 4 mirror and I checked that the problem disk are belonged to mirror partitions.
I tried format command and found the E3500 can not recognise the mirror partitions.
Can any SUN expert help me?
II have try another MAC, but it still shown the same message....
-
HELP : MacBook will not start !! Well, actually ...
Hello to you all Apple/Mac lovers ,
As the title said, my MacBook has gone wild. Here's the thing : I start it up, the gray apple appears and the spinning wheel under it. After an unusually long time of spinning, my computer ... shuts down. And that's it. Hopefully one of you will be able to fix it, usin the info below.
I tried to fix it, and here's what I did :
- I first used the Apple Hardware test (by inserting the installation DVD and pressing D on start up) : no errors detected.
- Then I used the disk utility (by inserting the installation DVD and pressing C on start up) : there, it said that there was an "Invalid sibling link", and that it couldn't complete the verification or repair because "The underlying task reported failure on exit".
- Lastly I used the "Startup Disk" application (found with the Disk Utility) and it first showed me 3 things : the Mac OS 10.5.3 folder from my hard disk (which is what it usually uses), the Mac OS 10.4.8 Install Disk, and then a Network Startup (but that's not gonna work). However it was quite late in the night so I chose the option "Turn Off" (in one of the top menus) and went to bed.
The next morning I repeated the previous procedure but this time the Leopard folder did not show up !! This is where I am at right now. Here are what seem to be my options :
- Re-install 10.4.8 (it will store 10.5.3 in a folder called "Previous System"). It says that I will not be able to boot from there anymore - is that true ? I should like to, because if the system needs to erase all data from my hard disk, then I will need to use my Time Machine backup from my external HD (and therefore will need Leopard).
- Wait for my dad to bring me the Leopard Install DVD (he'll be there next Sunday, 29th of June) from which I will be able to re-install Leopard.
Now I really do not know what is the problem - and if re-installing the OS will solve anything. There is still this strange Hard drive error - any idea if 1. that is the cause of the problem 2. what it means 3. If I need to fix it 4. how do I do that ?
Thanks for all your advice and time ,
#CharlesYour idea, Simon, seems best in my case. Now just out of curiosity - you say that I can recover all my files once I get back to Leopard using Time Machine, but will I also recover preferences/settings, from system preferences to application settings ? My question really is : is there anything I will not be able to recover ?
Anyways, now on to you adsfushi72. You say I need to get my "important files off the hard drives" - you mean I need to back them up in case my hard drive is broken and will need to be re-formatted in the process of re-installing, right ? Well the entirety of it is backed up on another, external hard drive, using Time Machine. The last backup was about 17 minutes before the problem appeared so all I could lose in the process is a few lines of text I typed in between. I love Apple ...
And how about safe/verbose modes ? What exactly are they ? I've used safe mode on a PC before, but I don't know how to start up in that mode on a Mac, what it exactly does or is, how to handle it, and why I would do that right now - I'm not saying I don't feel like doing it, I just want to know what information it could give me or in what way(s) it could help solve my problem. Same applies to verbose mode.
Lastly, a little update : Now when I start up my MacBook I see the Flashing "?" on a folder, which means it can't find a system folder to boot from - right ? So then I start up with alt/option pressed - and it does not detect any drive. When I insert the Mac OS X install Disk is only sees that. Is the invalid sibling link of my hard drive causing it to be unusable the system to boot from or what ?
The weirdest part is that now the hard drive seems to be absent. Before, it was there but I couldn't boot from it - since it seems to be damaged -, but now it doesn't even recognize or see it anymore. It seems the repair attempt is what made it change that way ... anyways thanks for all your ideas .
#Charles -
Help, Render will not Start?
Hello,
I mainly work with Edius but am using Premiere CS4 to finish a greenscreen project.
I have the work area set and when I go to Sequence-Render work area nothing starts to render.
The render dialogue box appears but no progress is made and when I go to "render details" no data is shown, just -- next to each line.
I have used Premiere back in the 1.5pro days, so I am familiar with the program.
This is a 1080p30 project with a 720p sequence if that is causing the issue.
Thanks for your help!I mainly work with Edius but am using Premiere CS4 to finish a greenscreen project.
Not the best of approaches, since PR sucks for chroma keying. Keylight in AE or Ultra CS3 are much better.
This is a 1080p30 project with a 720p sequence if that is causing the issue.
In CS4 there are no project settings, only sequence settings and your best bet is to use sequence settings that match your source material.
I have the work area set and when I go to Sequence-Render work area nothing starts to render.
Do you see a red bar over the timeline? -
PowerMac G5 not starting properly
Sorry to repost but I accidently marked my discussion as answered. Please see:https://discussions.apple.com/message/17155939#17155939
Hi,
I have the following machine:
Model Id:PowerMac11,2
Processor Name: PowerPc G5 (1.1)
Dual 2.3 GHz
2GB RAM
Problem:
Starting 12/28/2011 After I came home from work the Machine would not boot up. The white light would light up, the fans would start spinning normally but there would be no chime and nothing else would respond (keybord, monitor, etc). After a few seconds the fans will start spinning and getting louder. I forced quit it by holding down the power button. I tried to restarted and would get the same results.
I tried the following:
Disconnected all devices/cables except keybord and monitor
Removed video card and put back in
reset the SMU
have not tried resetting PMU because the keybord was not getting power
removed all RAM
installed only 2 sticks of RAM
After doing all of the above to no avail, I put my ram back in (properly) and called it quits for the night. I unplugged the power cord from the back of the machine.
The next day after work I came home, plugged in the power cord and started the machine. To my surprise it bootted up just fine. I ran the utility tool to verify the disk and it failed (knowing that this is not the problem I decided to boot off the Installl disk and repair anyways). I hit restart and was back to the computer not responding and reacting like the night before (no response, then fans start reving). I tried to restart it a few times to no avail. Again I pulled the power cable out from the back of the machine and went to bed.
Today I came home and like the night before it started up, I booted of the CD this time and repaired the disk, re-verified and all was well. I tried to restart it and i'm back to the machine not responding.
Any help with this is hugely appreciated!! Could it be the pram battery?
Please advice.
Thanks - FrankFrank, if you have a multi-meter you can check it out, it's hard to find any Apple people to still work on G5s at all, maybe a few independent AASPs though.
Here's some more info on G5 PSU voltage values:
http://www.insanelymac.com/forum/lofiversion/index.php/t105113.html
Looks like they changed the link, sorry... -
Help, safari will not start at all since update to newest version
Help, I am an admitted computer idiot- I always have had Macs because they are intuitive. My software updated automatically this week to the newest version of Safari, and now I cannot open Safari at all, I cannot even get to the Safari menu. I am using Firefox to type this - and I would rather use Safari as I am used to it. When I click on Safari the icon bounces up and down, then an error message appears saying that Safari quit unexpectedly, and do I want to send a message to Apple. I have clicked that message tab about 1000 times, no response.
Can someone help me fix this- using very simple instructions, thank youWe need to see a crash report, so restart Safari and when it crashes, copy the entire crash log and paste it into a reply window here. Notifying Apple is fine, but they will not respond, so you shouldn't expect that.
Mulder -
My good old Power Mac G4 with a brand new battery doesn't start up. The power button on the tower won't depress. The power button on the display doesn't respond either. I'd like to keep this computer (alive). What is the possible problem? (besides old age) Is it repairable? If it is, any idea on the cost? Somebody help me with a clue. It was getting harder to start up a few months ago, but I had some response. Now it is total silence. Thanks
Hello,
Was waiting for one of the others to pipe in, but see this far a start, about a G5 but just the pinouts for voltages are different...
https://discussions.apple.com/thread/3622041?tstart=0
http://www.allpinouts.org/index.php/Power_Mac_G4_Mainboard_Power_Supply
Of course it depends which G4, but this may help also...
http://www.xlr8yourmac.com/systems/ATX_G4_AGP_conversion/G4_AGP_to_ATX_case_pg2. htm
http://atxg4.com/ -
[help] Z77A-GD65 not starting fully
ok so when i turn on the motherboard all the fans in my PC turn on and the LED1 light turns blue for about a second then everything shuts off. My power button stays green even when everything else shuts off and the alarm LED is OFF. I have tried re plugging everything in and am placing only one stick of RAM in the correct spot. here are my system specs:
CPU: intel i5-2500 3.3 (3.7 turbo boost) i5-2500 Sandy Bridge
GPU: GeForce GTX 560 - ASUS ENGTX560
RAM: 8Gigs @ 1600 - G.Skill Ripjaws X Series
PSU: 550w - XFX Core Edition Pro
HDD: 500G @ 7200RPM - Seagate SpinPoint F3
ssD: 60G @ 525MB/s read, 475MB/s write - OCZ Agility 3
MotherBoard: MSI Z77A-GD65
Tower: Corsair Carbide Series 400R
OS: w7-64bit Home Premium
DD: ASUS DRW DVD:RWHi
I just got that same board.
If you keep looking at the Diagnostic display on the board while starting the PC, then just notice what the code is when it stops. The display should change code according to what init state its in.
That way you can determine at what initialization step it fails. Check the manual for the error codes.
For example if it stops at Cpu Initialization, there is a good chance that the CPU is faulty or simply overheating if cooler is not properly seated. From what you explain, it could sound like Overheating CPU.
Are you using the H80 cooler in this build? It can be a bit tricky to mount properly.
You can also try the Bios switch to swap over to the backup Bios. In case the bios is corrupt. -
Need help with Quicksilver not starting up
Hi, this is my backup computer. It doesn't get a lot of use since I have a Mac Pro, but I still want to have it up and running again. The symptoms are when I press the power button it appears to come on, the fans inside power up but the white power button on the front doesn't stay lit up. Also there is no start up chime sound when it is turned on.
I have opened her up and removed and checked each memory stick. I realize it could be one of several things. I am hoping it is just the battery. That would be a cheap and easy fix. If it a bad logic board or something along those lines it wouldn't be worth repairing. I just wanted to hear some more thoughts on some other possibilities I might not have considered.
It is a 2001 Quicksilver 867 upgraded with a dual core 1.5GHz. Thanks in advance for any tipsIf the Mac has not been connected to AC power for a while, it's most likely that the internal PRAM battery has discharged & needs replacement.
Check this site for battery part numbers and sources. https://sites.google.com/site/macpram/mac-pram-nvram-cuda-pmu-battery-tutorial Mac PRAM, NVRAM, CUDA/PMU & Battery Tutorial
Some things to try.
* Reset the PMU http://support.apple.com/kb/ht1939
* Resetting the Logic Board - Resetting the logic board can resolve many system problems. Whenever you have a unit that fails to power up, you should follow this procedure before replacing any modules.
1 Unplug the computer.
2 Press the Power On button on the front of the unit.
3 Open the side access panel.
4 Remove the battery from the logic board.
5 Wait at least 10 minutes before replacing the battery.
6 Make sure the battery is installed in the correct +/-
direction.
7 Reassemble the computer and test the unit.
* Resolve startup issues and perform disk maintenance with Disk Utility and fsck
http://docs.info.apple.com/article.html?artnum=106214
Cheers, Tom -
Help, Mail will not start
Hiya, I am relatively new to macs. (to my shame I am more familiar with pcs). I was using mail earlier today for work, and yet now when I try to open it, it immediately quits. bringing up a box "The application Mail quit unexpectedly'
I have tried restarting etc, but to no avail. Anyone seen this before? any ideas?
thanks,
sillyfishyboyHi Sillyfishyboy.
Does Mail crash immediately upon start up or when it starts to download messages?
If the former, the cause could be a troublesome message with HTML content that Mail tries to load every time it starts up. Try this:
1. Launch Mail holding the Shift key down until the main window appears. This should prevent Mail from trying to select any mailboxes or load any messages upon start up.
2. Go to Preferences > Viewing and disable Display remote images in HTML messages if it's enabled -- having this setting enabled is a really bad idea for spam-related security reasons anyway.
3. If the preview pane is visible in the main Mail window, drag the horizontal separator bar between the messages list pane and the message preview pane to the bottom of the window, or just double-click within the separator bar, so that the preview pane disappears and only the messages list is visible. This prevents Mail from trying to load a message when it is selected in the messages list pane.
4. You should now be able to select the message that's causing Mail to crash and either delete it or move it to another mailbox, to prevent Mail from accidentally trying to open it -- the problem could be a bug in Mac OS X that might or might not be fixed in a future version.
5. If you want to make the preview pane visible again, drag the horizontal separator bar up from the bottom of the window, or just double-click on it again. -
Help!Can not start the database by sqlplus!!!ORA-12514:
OS:window xp
oracle 10g
sqlplus /nolog
SQL*Plus: Release 10.1.0.2.0 - Production on 星期六 5月 20 15:08:26 2006
Copyright (c) 1982, 2004, Oracle. All rights reserved.
SQL> connect sys/demo@demo as sysdba
ERROR:
ORA-12514: TNS:listener does not currently know of service requested in connect
descriptor
Message was edited by:
[email protected]Yes!
lsnrctl services
LSNRCTL for 32-bit Windows: Version 10.1.0.2.0 - Production on 20-5月 -2006 15:1
2:44
Copyright (c) 1991, 2004, Oracle. All rights reserved.
Connecting to (DESCRIPTION=(ADDRESS=(PROTOCOL=IPC)(KEY=EXTPROC)))
Services Summary...
Service "PLSExtProc" has 1 instance(s).
Instance "PLSExtProc", status UNKNOWN, has 1 handler(s) for this service...
Handler(s):
"DEDICATED" established:0 refused:0
LOCAL SERVER
The command completed successfully
no "demo" service,why?
Maybe you are looking for
-
Hello there, I wonder if you could help. I have a new macbook pro with the largest HD I can get and faster processor. It's a lovely piece of kit. But the problem is that that I edit a lot of films and have lots of stuff already on it so I have almost
-
Hi all, at a customer’s site I’ve a problem with a fresh installation of Backup Exec 2014. Every backup (full or incremental) always reports the following error: “An unexpected error occurred when cleaning up snapshot volumes. Confirm that all snappe
-
Proxy settings of chrome or chromium don't take effect
I'm using archlinux+kdemod 4.5. The proxy setting of all versions of chrome or chromium seems not to take effect because my ip address doesn't change(http://www.ip-adress.com/) . I also tried swithcy! proxy but it doesn't help. However, starting the
-
G500 with Radeon HD 8750, new games not working.
Hi, I have a Lenovo G500 with Intel HD4000 and Radeon HD 8750M switchable graphics. I was having trouble getting Kings Bounty: The Dark Side to work and also Divinity Original Sin. They were just crashing to the desktop. I updated the graphics driv
-
Question Regarding Delta Update.
HI HI all Gurus... I m new in BW i want to know tht if we have schedule delta for update in bw but if whenever detla is failed for any reason.then we must have to start from initial step..or we can start from thr whr it was stopped..and also give t