Help!!!problem with CPU temp!!!

i am using mega 180,and i have lapped the heatsink,reverse the fans on the heatsink,and use artic silver grease and made a duct for the heatsink,but my CPU temp did'nt low down,on the contrary,it raised about 5C!!!
i am using an amd athlon xp 2500+(thorton)@11.5x166MHz,i have 8606 pci card and 6200 agp card installed,before the temp is:CPU idle 55 and GPU 55,but now it is CPU idle 60C and GPU 65C!!!
can anyone tell me why the TEMP get hotter than before???

Let me add this to this thread.....MEGAs all have heat problems, but with some effort, all the problems can be addressed. Installing a better HSF is only one way to deal with the heat. My MEGA 651s have a special heatsink mount method.....most std heatsinks won't attach properly to the little plastic clips.
However...remove the plastic clips from the MB (four screws) and you can substitute four brass MB stand-offs. With these in place, you can then install a variety of good heatsinks.....with some work/mods.
Here are some photos of two I have installed...an ALPHA 8942, and an AEROCOOL HT-101.
The Aerocool was the hardest to install, but works the best. It did not require any mods to the MEGA that could not be un-done (for a warranty return).
I'm sure with some searching/work many other heatsinks could fit. The result is a much cooler running MEGA.

Similar Messages

Problem with CPU Voltage

Hello
I build new PC with:
i5-760
Noctua NH-D14
MSI P55-GD65
G.Skill 2x2GB CL7 ECO
Antec TruePower New 750W TP-750
TwinTech GF 9600GT
I have problem with CPU voltage as even when I set it for example to 1.201v in bios, under load it overshot to 1.256-1268. The best is when I oc`ed cpu to 4GHZ and set voltage in bios for 1.30v it overshot for 1.45v+! Not to mention that temps are skyhigh from that. It doesn`t matter if I try to put BIOS Vcore on 1.1v on stock because under load it still rise to 1.16. I turned off all eist, c-state, turbo boost, phase led and switch phase, set vdrop to low and still something is wrong here. I updated the bios under dos from USB stick to newest 1.9 version in order to update CPU micro code without error and it not helped. I want to know is that even possible to fix or should I RMA MB or CPU.
Minor problem is with sysfans as they power on for a second and turn off instantly to start working again when I see list on devices in post. After rebot when my monitor is switched off it takes something like 5 sec to power monitor on and another 5 to show bios, is that normal?

I have similar issues, it's hard to tell which measurement is the most accurate, there are 2 different measurements in the control center that don't match up with the figures set in the bios. The only way to be sure would be to get an expensive accurate multimeter but If you're only interested in running a stable overclocked computer without knowing the exact figures then get the computer running stable and lower the voltages until it starts to become unstable with prime95,
Or you could work the other way round, set the voltages so it boots but doesn't run prime95 for long, then raise the vcore and vtt one at a time until your happy with the length of time prime95 runs without errors. I'd be happy with 24 hours, I seem to remember errors creeping in at around the 9 hour mark on the setting below what I have it set to now.

Premiere Pro CS5: please help problem with importing a file error output "there was an error decompressing audio or video"

please help problem with importing a file error output "there was an error decompressing audio or video"

this is related to what adobe program/version?

Problem with CPU?? need help badly

Hey guys, its been a sad two days for me.. I have the MSI k7T266 PRO, and yesterday while i was moving tires into my apartment, one of them fell hard on the floor and my computer shifted, i opened the pc to find out that the CPU fan has shifted from the cpu, and the cpu smelled kind of burnt..
Anyway i had an ATHLON XP 2200 i think...
Anyway i went to compusa today and got a new CPU, an AMD 2400+ SEMPRON PROCESSOR. i installed it, put my huge heatsink,fan, and powered up.... NO SHOW..
The Diagnostic LED's show 4 RED lights,(which according to the manual means a problem with the CPU), it was showing 4 red lights with my old blown cpu and its still showing 4 red lights with the new cpu.. im getting frustrated..
Anyway i tried resetting the bios using the JBAT jumper, it still doesnt work..
I know the new CPU is good because i can tell a blown CPU..
So can anyone help me out??

Hello,
http://www.msi.com.tw/program/search/ser/SerConProRes.php?keyword=k7t&kind=
Which one is yours?
The Sempron 2400+ CPU has a 166Mhz FSB.
Your board does not support this CPU.

Success with iTunes but a problem with a temp file

Further to my recent post, I have now had some form of success with opening iTunes but I can only do this if my external hard drive (which has the remnants of some file left).
I have tried to copy and paste the files relating to iTunes but for some reason, I am unable to even access a file labelled "TEMP FILE".
Can anybody help or indeed send via email a copy of the file as I dont think there is anything in it. I know that when I have my external drive repaired I will not be able to access iTunes.
PLEASE HELP !!!!!!!

iTunes cannot run because it has discovered a problem with your audio configuration.
That one is most commonly caused by a problem with your QuickTime. (iTunes uses QuickTime for audio and video playback.)
The following document may be of some assistance:
iTunes 7 for Windows: iTunes has detected an audio configuration problem

X38 Platinum: Problem with CPU detection

Hi everybody,
I've got a little problem with my newly acquired x38/platinum...
I'm currently assembling a new PC on my own... So far all the component have been plugged-in EXCEPT the memory modules (I haven't purchased them yet).
Despite this complete lack of memory, I try to test the correct boot-up of the system.
And then the following problem occurs: the "lcd post" display hang on "CPU" (before rebooting indefinitely)... Not "DRAM" as expected...
The CPU is a Core 2 Quad, and is correctly powered with a 8-pin/12v connector. The CPU-Fan is powered from the correct on-board pins (cpufan). The speakers are plugged, but no specific "beep" are emitted.
One possible mistake I've made: the CPU-Fan is not fully plugged with the 4 "screws": i only (and hardly) manage to clip 2 of them, I'm afraid of breaking the board if y try too hard with the two others.
Could this problem be caused by the absence of DRAM? Or more likely by the the fact that the Fan is not fully clipped? By the way, is that normal that the CPU Fan is so Hard to plug correctly?
Any comments or idea would be greatly appreciated
Thanks (and sorry for the approximate english)
MH.

Quote from: Jack the Newbie on 23-January-08, 22:03:59
mhz42, please provide full system specs. Otherwise it is very hard to help you with your problem. What brand and type of memory are you using? What other components are part of your system configuration?
The mb is a x38 platinum 1333. The proc is a quad core qx8650, 1333fsb. The hd (western digital caviar) and optical drive (lg h66n) are both on sata and plugged. The memory used is 2go Kingston ddr3 1375mhz... (plugged in DIMM 1/2).
Anyway, I frankly doubt that the problem could come from anywhere else than the cpu (considering the post message)...
Quote from: Jack the Newbie on 23-January-08, 22:03:59
What PSU are you using?
A seasonic M12-500w... brand new...
Quote from: Jack the Newbie on 23-January-08, 22:03:59
Did you properly plug in ALL power connectors?
The powering should be ok... (the MB, the proc, the cpufan and the graphic card are plugged) The processor seems to be correctly powered, if it was not the case, the post process wouldn't even start (tested)...
Quote from: Aaron Yuri
You could just buy a cheap Pentium 4 and flash it with that.
That's an idea. Or i could directly ship the mb back to msi and thell them to do it themself... After all the spec says cleary "quad core compatible"...
So?
Just to be sure: the "since 1.1" from the compatibility table from MSI, refeers to the bios version right? Not a sort of MB revision or something?

Serious problem with CPU "maximum frequency"

Hello,
I have a problem with my W510.
I think that this problem has been around since I purchased it, or at least since a month or so after I purchased it.
When I plug power in or out it almost always affects the CPU's maximum frequency, as can be seen in Windows 7 Resource Monitor, and also in a program called CPU-Z which actually shows the current Core Speed.
When things work properly, the core speed is a little over 3,000 Mhz.
However, this speed changes whenever I plug the power in or out.
It usually changes for the worse when I plug the power IN!
Often, upon plugging it in, the speed drops to around 1,000 Mhz. Then I plug it out - and the speed goes back to 3,000 Mhz. Plug it back in - 2,500 Mhz. Plug out - stays on 2,500 Mhz. Plug in - 1,500 Mhz. Plug out - 2,500 Mhz. Plug in - 3,000 Mhz. Plug out - 3,000 Mhz, etc. Every once in a while it even drops to 300 Mhz.
It seems to be random and arbitrary. Sometimes it takes me 10, 15, even 20 times of plugging the power out and back in to get it to work at 3,000 Mhz.
The machine is new, there is no fan noise, and anyway the changes are directly correlated to plugging and power in and out, and they never occur on their own - so it's definitely not overheating or anything like that.
I also don't think that it's an issue with the power itself, since it happens to me in different places and different countries, and in every place if I try to re-plug the power enough times - it will eventually be resolved (so obviously there is enough power).
Is there anyone else who's experiencing this problem? Any suggestions?
Thanks
Solved!
Go to Solution.

I have found that Throttlestop helps me with my own speedstep problem. The speed moves a lot at light usage due to speedstep, but when i use a cpu benchmark to load the four cores they set to max speed and don't move. You could give it a try.
Regards,
Fernando

MSI CD53, i5 750 - Problem with CPU Fan Speed

Hello
I have problem with this counfiguration: i5 750, MSI CD53 Motherboard.
I Have processor overheating poblem. I noticed that processor easly can go up to 90C.
I check phisycal installation, and all its ok.
After that i check RPM of CPU FAN and i noticed that it cant go over 1000 RPM, so propably this is problem.
In MSI Control Center maximum i can set 1000 RPM.
I read that CPU FAN can go up to 3000 RPM.
Maybe i have something wrong set up in bios? What can i do with this?

Quote
CD53
Which board exactly do you have?
What is your current BIOS Version?
What kind of CPU-Fan are you using (3-Pin or 4-pin PWM (four wires) and which connector is it attached to?
What are your current fan speed/control settings in BIOS Setup?
Quote
I check phisycal installation, and all its ok.
Physical installation is one thing, but what about thermal paste (have you used a PROPER amount (too much thermal paste has the opposite effect))?
What about your case ventilation?
Quote
I noticed that processor easly can go up to 90C.
Please check the CPU's core temperatures with CORE TEMP, REAL TEMP or HW-MONITOR!

Msi a55 e33 + r7 260x Graphics problem + amd cpu temps?

Hello, i have some problems with my new build
My system is,
cpu: amd athlon 750k
mobo: a55e33 msi (bios 11.4)
Gpu: sapphire r7 260x
ram: corsair vegeance 4gb
psu: corsair vs450
1) The problem is like this, whenever i don't do anything on my pc the monitor goes black and the pc crashes sound stucks some times and i have to reboot... tried several gpu drivers some crashes right away and some are like this.. is this a gpu issue ? Anyone with same experience ?
2) Second problem my cpu temperature is inaccurate and the only program that display a temp is cpuid hwm, cpu idles at 40-50c and goes as far as 80c based on the program... that was with stock cooler, upgraded cooler with an alpenfohn sella (deepcool rebrand) and the problem persists, temps were similar even with older bios version and the same older version board... is this a cpu problem ?
ps. Prime 95 for 4 hours hwm indicates 80c touched cooler with bare hand multiple times during this period not even near this temp even at the lower end of the cooler ...
thanks 4 any suggestions

Quote from: Nichrome on 17-January-14, 00:32:30
Hi,
my idea is that your power supply is not efficient enough for r260x.
Try without the graphics card.
About the CPU temps, try to reapply the thermal paste. (when you've exchanged the cooler, have you cleaned the CPU?)
It also might be the problem with the software (or BIOS). Spend couple of $ and buy an external CPU temperature checking tool (don't know proper name of it).
Power supply is enough for the gpu probably driver issues as other users have the exact same problem with the same card, cpu temps are definitely mobo/bios or cpu related yes yes i cleaned the cpu i cleaned everything and reapplied ic diamond .. temps are the same with stock cooler and aftermarket cooler can't be coincidence + no program indicates temps other than hwm
Take notice i had 2 msi a55e33 one with bios 11.1 and another one which came with 11.4 from factory
Conclusion ? or the cpu is broken or the mobo indicates wrong temperatures

Please Help New Mobo CPU Temp 255 Deg Celcius

Hi, I just bought Big Bang Marshall with all the new computer part yesterday, after i finish installing everything then i started the computer, went to BIOS was planning to choose my boot driver, then i went to check the cpu temp. the cpu is 255 degress at 4.6mhz speed which i have not configure anything yet not even overclock yet. but then i put my hand and feel the temp in the cpu cooler it was warm not hot at all. but i worried that the 255 deg is real and might blow everythign so i turn off. thats the only time i turn it on, then today i phone the shop and the shop didnt know anything they never experience 255 deg. so i need to wait till monday until msi customer service open. but i got whole day today, i am wondering if people can help so i might able to fix the issue. should i continue and install the windows or should i wait till msi open again? thank alot
my part is:
mobo: Big Bang Marshall (B3 rev)
procesor: i7 2600k
cpu cooler: H70 Corsair
CPu thermal paste: Gelid
Video card: MSI GTX580 Lightning x2 Sli
PSU: Corsair AX1200
Ram: Gskill Ripjaws X 2133mhz 4x4gb
os: windows 7 ultimate

Quote from: HU16E on 05-June-11, 14:38:12
As long as the RAM defaults properly to 1333 like it is supposed to, all should be fine with having 2133's installed. RAM speed is kind of a sore subject with the Sandy Bridge platform. Not much is gained by 2133 in performance, but if you wish to persue more speed, please open a thread in the OC, Undervolt, & Mod Section of the forum.
thankss alott
Quote from: Bernhard on 05-June-11, 14:37:35
If you are not into extreme overclocking, then indeed a JEDEC standard 1333 set is all thats needed. If yours defaults to 1333 though and is stable, then you should be fine.
thankss alott

Photoshop Premiere 9 vs 13? Are there any problems with CPU usage and crashing?

I stopped using Premiere, because they the computer would freeze and/or the program. I was curious if there was any issue with people currently using Version 13? I think I loaded it on this computer along with Photoshop Elements 9. After a while I just kept Photoshop Elements.
System Specs:
Windows 7 premium home edition
Processor Intel R Core TM i5-2410M CPU @ 2.30 GHz 2.30 GHz
Installed Memory 6.00GB 826 GB free
64 Bit Operating system

stephanies
If 64 bit, while 9 will be a 32 bit application with the limitations of a 32 bit application on 64 bit system, 13 will be a 64 bit application which translates into more computer resources available to 13.
Elements Organizer 9 will not integrate with Elements Organizer 13 although you can convert the 9 catalog in Elements Organizer 13. And there is a marked difference in the workspace between the two versions. Principles tend to stay the same, but features can be moved, changed, or discontinued.
I would have expected Premiere Elements 9/9.0.1 to have worked in your computer environment. Since it did not, I would strongly suggest that you look at the free 30 days tryout of Premiere Elements 13/13.1 in your computer environment to assure the compatibility of it with your computer environment and project goals.
Lots of causes for program crashes (any version).
a. Conflicts with antivirus program.
b. Problem with video card graphics card
c. Use of a pen and table device instead of mouse
d. Problematic source media and format conflicts
e. Not running program as Administrator
f. Poor installation
g. Failure to install QuickTime along with Premiere Elements on the computer
h. Not meeting System Requirements in some way.
i. Other
https://helpx.adobe.com/premiere-elements/kb/system-requirements-premiere-elements.html
Please review and consider. Any questions or need clarification, please do not hesitate to ask.
Thank you.
ATR

HELP/Problems with pull-down navigator bar

Hi everyone,
I was wondering if I could get some input. I have just
re-designed our magazine's site, www.easternsurf.com
I used Pop-Up menu function in Fireworks 8 to generate our
Navigator bar. For the most part everything has been working well,
BUT we've had a couple of complaints that the navigator bar's
pull-down menus get stuck behind the photos/banner ads/etc. instead
of in front of them when viewing in Internet Explorer. I'm on the
Mac platform (OSX Tiger/Macromedia Studio 8) and have seen no
problems viewing in Safari, Firefox and Netscape. The only
complaints have come from Internet Explorer users. A couple of
people updated their browser to the newest version and the problem
disappeared, however we've still had a couple of people that have
written in that the newest version of IE is still not displaying
properly.
Also we've got a strip of button ads running down the left
hand side of each page and I've also seen another issue that's
common on sites of this type...when the pulldown menu overlaps with
a Flash element, there is a problem with the screen re-draw. I've
seen this on several other sites and know it's a common problem,
but does anyone know of a workaround where this won't happen? I
just noticed that signing on to Adobe's site, there almost seems to
be a command where the menu keeps re-drawing at a very rapid rate
so this won't happen.
Any input would be greatly appreciated, although I'm Mac all
the way, we are a business and have to get this site visible for
everyone!
Thanks

Hi Oldbudge,
Welcome to the Community,
Please Perform a Battery Pull Restart like this While Device is Powered On remove the Battery wait for a min. then re-insert it back wait till the device take a long Reboot.And see if that helps.
Good Luck
Prince
Click " Like " if you want to Thank someone.
If Problem Resolves mark the post(s) as " Solution ", so that other can make use of it.
Click " Like " if you want to Thank someone.
If Problem Resolves mark the post(s) as " Solution ", so that other can make use of it.

MSI Max 2 BFIR; Problems with CPU Fan speed in PC Alert!

servus...
First of all, I have Bios version 1.3 from the .de support Page.
I don´t know, why .com.tw doesn´t have this version.
But here´s my problem:
PC Alert doesn´t show a CPU-fan speed!
The northbidge fan shows the fan speed roundabout 5000.
In BIOS CPU Fan ~2500
PC ALert versions:
4.005
4.006
Any ideas?
Thanks

Thank You for the reply,
Before the latest update to PCAlert4 it was working properly, I cross checked the reported info. to that of Sandra, MBM, and in the bios.
Also the temps are only swapped between the system temp. and the CPU temp., other than that they are correct.
Thanks,
John

Help - problem with white iphone 4 speaker

Hi, i have a problem with my white iphone 4 speaker. I know the specs stated that the mic is supposed to be on the left and the right is the speaker but i've compared at least 2 other black iphones 4s and there is some volume from the left side (if you close the right side) whereas mine is practically non-existent. Should i be concerned? Is this specific to the white iphone 4? The local telco has not been helpful - they can only reformat the phone and said that this is a software problem. Anyone with similar experience pls share. Thanks in advance.

irene sim wrote:
Hi, i have a problem with my white iphone 4 speaker. I know the specs stated that the mic is supposed to be on the left and the right is the speaker but i've compared at least 2 other black iphones 4s and there is some volume from the left side (if you close the right side) whereas mine is practically non-existent. Should i be concerned? Is this specific to the white iphone 4? The local telco has not been helpful - they can only reformat the phone and said that this is a software problem. Anyone with similar experience pls share. Thanks in advance.
You already know the answer. ALL iphones, every single one of them, have but one speaker at the bottom. You have NO ISSUE at all with your speakers. None. Nothing is wrong. At all. No problem. None.

Pleaseeeeeee Help - Problems with position of my web page

Hi, first sorry on my english
I have problem with position of my page. I had made my web page in Indesign CS5 and exported to swf file. My web page is working fine (www.igor-flytying.com) but the page is not in the middle of the web browser. How can I fix the problem????? I am a beginer in Indesign. I had try to make some changes in html file (salign) but still nothing.
Please HELLLLLPPPPPP
Regards
Aljosa

Petteri, SWFObject is much better because it loads the JavaScript so you don't see it inside the HTML page, but it still wraps the swf in a div which by default will be positioned in the upperleft of the browser window.
This is the only way I've been able to center using SWFObject—note that it's the "flashcontent" div style that does the centering not the align embed parameter:
<!DOCTYPE html PUBLIC "-//W3C//DTD XHTML 1.0 Strict//EN" "http://www.w3.org/TR/xhtml1/DTD/xhtml1-strict.dtd">
<html xmlns="http://www.w3.org/1999/xhtml" lang="en" xml:lang="en">
<head>
<title>S W F | Centered</title>
<meta http-equiv="Content-Type" content="text/html" />

<style type="text/css">
          #flashcontent {width: 1000px; height: 750px; margin-left: -500px; margin-top: -375px; position: absolute; left: 50%; top: 50%;}
</style>
          <script type="text/javascript" src="swfobject.js"></script>
          <script type="text/javascript">
                    var flashvars = {};
                    flashvars.myFlashVar = "Testing";
                    var params = {}; //Embed parameters: http://kb2.adobe.com/cps/127/tn_12701.html
                    params.quality = "best";
                    params.align="t"
                    //SWFObject parameters: http://code.google.com/p/swfobject/wiki/api
                    swfobject.embedSWF("swftest.swf", "flashcontent", "1000", "750", "10.0", false, flashvars, params);
          </script>
</head>

<body style="background-color: #888888">
          <div id="flashcontent">
                    <a href="http://www.adobe.com/go/getflashplayer"><img src="getFlash.gif" alt="adobe icon" border="0" /></a>
          </div>
</body>
</html>

Help!!!problem with CPU temp!!!

Similar Messages

Maybe you are looking for