Help required in configuring multicast routing

Hi,
We have two 2 servers and 200 clients.
2 servers are in one vlan, 200 clients are in another vlan.
first server will send data to second server with multicast address 234.5.6.7
second server will send data to 200 clients with multicast address 234.5.6.8
first server is able to send data to second server.
but second server is not able to send data to clients.
If we put clients in same vlan, second server is able to send data to clients.
So we understood that multicast routing needs to be enabled in L3 switch.
Switch Model: 3550
IOS version: 12.1(19)EA1a
Any help in configuration required for this.........
Regards
SKRAO

Hi Skrao,
Does your client vlan and server vlan exist on same layer 3 switch if yes then perform this config and it should work..
On global config mode
ip multicast-routing distributed
On interface vlan config (for both client vlan and server vlan)
ip pim sparse-dense-mode
You can very well fine tune later.Try this and update if it worked.
HTH
Ankur

Similar Messages

  • Help required network configuration - Gateway route settings get erased on reboot.

    Oracle Linux 7
    Linux myhostname 3.8.13-35.3.1.el7uek.x86_64 #2 SMP Wed Jun 25 15:27:43 PDT 2014 x86_64 x86_64 x86_64 GNU/Linux
    #cat /etc/sysconfig/network-scripts/ifcfg-eno16780032
    TYPE="Ethernet"
    BOOTPROTO="none"
    DEFROUTE="yes"
    IPV4_FAILURE_FATAL="no"
    IPV6INIT="yes"
    IPV6_AUTOCONF="yes"
    IPV6_DEFROUTE="yes"
    IPV6_FAILURE_FATAL="no"
    NAME="eno16780032"
    UUID="2d1107e3-8bd9-49b1-b726-701c56dc368b"
    ONBOOT="yes"
    IPADDR0="34.36.140.86"
    PREFIX0="22"
    GATEWAY0="34.36.143.254"
    DNS1="34.36.132.1"
    DNS2="34.34.132.1"
    DOMAIN="corp.halliburton.com"
    HWADDR="00:50:56:AC:3F:F9"
    IPV6_PEERDNS="yes"
    IPV6_PEERROUTES="yes"
    NM_CONTROLLED="no"
    #route -n
    Kernel IP routing table
    Destination     Gateway         Genmask         Flags Metric Ref    Use Iface
    0.0.0.0         34.36.143.254   0.0.0.0         UG    0      0        0 eno16780032
    34.36.140.0     0.0.0.0         255.255.252.0   U     0      0        0 eno16780032
    169.254.0.0     0.0.0.0         255.255.0.0     U     1002   0        0 eno16780032
    When I reboot the machine, the first line in route table gets erased, I then run:
    #route add default gw 34.36.143.254
    After which network works fine.
    Help required. I don't want to use NetworkManager.

    The following might be useful:
    https://access.redhat.com/solutions/783533
    "When transitioning from NetworkManager to using the network initscript, the default gateway parameter in the interface's ifcfg file will be depicted as 'GATEWAY0'. In order for the ifcfg file to be compatible with the network initscript, this parameter must be renamed to 'GATEWAY'. This limitation will be addressed in an upcoming release of RHEL7."
    NetworkManager is now the default mechanism for RHEL 7. Personally I don't quite understand this, because as far as I can gather it is a program for systems to automatically detect and connect to known networks. I think such functionality can be useful when switching between wireless and wired networks, but for a server platform, I wonder.

  • Please help me in configuring a router!

    Hi! I have to configure a new router with a static route. No routing protocol will be used. Since, I'm a budding Network aspirant i do not know much about things. My senior Network Engineer has asked me to configure this router. There's an apartment where our Overseas employees stay, earlier this apartment had a broadband connection which was further divided through the APs(Cisco Wireless Access Points) and made usable to around 20 users. Now, they have bought in their own lease line and I have to configure this router. Please help me doing this as I'm not aware of anything else apart from what I have written here. Thanks a ton in advance!

    Hello,
    You should provide some info so that people can figure out what do you want to do. For example, what kind of leased-line is it? L2 or L3? Is it like a cable connecting two sites from your company or is there any router in between from your leased-line provider...?
    For what you say, the easiest thing would be to configure a default route to the other end of the leased line and voilà.
    Otherwise, you can always ask your senior Network Engineer to configure it (him/her)self or ask for help to him/her.
    Regards,
    Reg.

  • Help required in configuring telnet

    Hi,
    We have two PIX 515E firewalls working in HA mode.
    I wanted to configure telnet access to firewalls from outside interface.
    PIX version is 6.3(5)
    I kept PC outside to outside interfaces.
    PIX outside IP is 10.10.200.3, inside IP is 10.10.202.5 corresponding virtual IPs are 10.10.200.2 and 10.10.202.7
    I have tried following configurations:
    pix(config)#telnet 0 0 inside
    pix(config)#telnet 0 0 outside
    pix(config)#telnet 10.10.200.0 255.255.255.0 outside
    pix(config)#telnet 10.10.202.0 255.255.255.0 inside
    pix(config)#telnet 10.10.200.200 255.255.255.255 outside
    I am able to telnet from internal interface side using inside ip address.
    But from outside test pc with IP 10.10.200.200 I am not able to telnet to PIX.
    I enabled logging console 5.
    when I tried to telnet to outside virtual IP it is not showing any traffic to firewall.
    If I try to outside interface I am able to see the traffic like
    packets received from source 10.10.200.200 to 10.10.200.3
    any help in this configuration. I wanted to telnet firewall from test pc.
    Regards
    SKRAO

    HI SKRAO,
    from security reasons is not possible to telnet to outside interface there is no way how to permit this you need you ssh instead of telnet
    here is more info about setting ssh
    http://www.ciscopress.com/articles/article.asp?p=25342&seqNum=3&rl=1
    M.
    Hope that helps rate if it does

  • Help required in configuring counting rule

    I have limited experience in SAP-HR configuration. Kindly help me quota configuration. The client has only absence type u2013 Earned Leave. The leave rule is the same for all the employees. The leave rules are:
    1.     The employees are credited with earned Leave on Jan 1 every year, for the attendance days put in during the previous calendar year.
    2.     The employee is eligible for Earned Leave only if he has attendance for at least 240 days during the previous year. If the employee has joined the company during the middle of the previous year, then he should have attendance for at least 2/3 of the remaining working days during the year.
    3.     The employee should be credited with 1 day EL for every 20 working days. If the employee, for example, has worked for 268 days during the year then he should be credited with 13 days EL (268/20=13, with 8 days as remainder). The remainder days, if any, should be carried forward to the next year and considered at that point as added to the number of working days. E.g. employee has worked for 268 days in year 2010. He will be credited with 13 days EL on 1 Jan 2011. Assume he has worked for 256 days in year 2011. Then while creating the absence quota for EL on 1 Jan 2012, the system should consider working days as 256 (from year 2011) + 8 (remainder from year 2010) = 264. Hence the employee should be credited with 13 days of EL on 1 Jan 2012 (264/20 = 13 days; 4 days remainder).
    4.     Leave carry forward rules: The employee is allowed to carry forward the EL balance to the next year. However, after carry forward the total balance should not go beyond 30 days. Any thing in excess of 30 days will get lapsed, if it is not encashed.
    Kindly let me know how to configure the counting rule & the deduction rule for the above scenario.

    Hi
    Configuring of EL need PCR Calculation and Standard Configuration with time Types
    000010            D VARSTCURMO
    000020 **           COLOP*
    000030 04         D VARSTFDYPP
    000040 04 N
    000050 04 Y       D HRS=0     HRS=FR11C HRS?300
    000060 04 Y *
    000070 04 Y <     D HRS-300   HRS*-1    ADDDB9509 ADDDB9558 HRS?15
    000080 04 Y < *   Z HRS=0     HRS=M9500 GCY ZAC2
    000090 04 Y < <   Z GCY ZAC3
    this when u go for GCY ZAC2
               D HRS?10
             D HRS/10    ROUNDH<60HHRS?CELACR
    *        D HRS-CELACRHRS?0
    * *        HRS*-1    ADDDB9501
    * >        HRS=0     ADDDB9500ZADDMB9500ZADDDB9501ZADDMB9501Z
    >          HRS=0     ADDDB9500ZADDMB9500ZADDDB9501ZADDMB9501Z
    <            HRS=0     HRS=CELACRADDDB9501 HRS=0     ADDDB9500ZNEXTR A
    <        A   ADDMB9500Z
    This when u click ZAC3
    000010            D HRS=0     HRS=M9500 HRS?10
    000020 *            HRS/10    ROUNDH<60HADDDB9557 HRS-D9509 ADDDB9556 NEXTR A
    000030 *        A D HRS*-1    HRS?0
    000040 * *          COLOP*
    000050 * >          ADDDB9501 HRS=0     ADDDB9500ZADDMB9500ZADDDB9509ZNEXTR A
    000060 * >      A   ADDMB9509Z
    000070 <            HRS=0     HRS=M9509 ADDDB9501 HRS=0     ADDDB9500ZNEXTR A
    000080 <        A   ADDMB9500ZADDDB9509ZADDMB9509Z
    This PCR is for EL with 300 Limit
    Regards
    Raja Sekhar

  • Help required please! Netgear router to Airport Express to stream iTunes

    I have recently purchased an Airport Express and I have an iTunes account.
    I wish to stream music from a computer in one room to a Sony Hi fi in another room (not very far apart). I am having great difficulty in setting this up with instructions in the box.
    I have a NETGEAR wireless router provided free by Virgin when they put my broadband cable in. So I need simple step by step instructions on how to link the Netgear router on my computer with the Airport down on my hi-fi. I have the cable to the hi-fi plugged into the Airport and the router is working okay.
    I have spent hours on this and have also had a computer expert try to help me but he has drawn a blank. When I click on Airport Utilities the message comes up saying that it has not detected a wireless device. Scan Again! Can anybody help?

    initiate the set up using ethernet then configure the Express wireless setting. Y=As the second router you may need to put it in bridge mode. Use Airport Utility to do that.

  • Urgent help require to configure an SSL incoming socket provider

    Hi,
    We are using RIDC to integrate UCM with Portal application.
    Also using SSL Communication for the same but we are unable to stablish a connection between portal and UCM.
    We have filled the SSL provider's details as given below
    Provider Name: SSL_Provider
    Provider Description: For RIDC Test
    Connection State: down
    Last Activity Date: None
    Provider Type: sslincoming
    Provider Class: idc.provider.ssl.SSLSocketIncomingProvider
    Provider Connection: intradoc.provider.SocketIncomingConnection
    Server Thread Class: intradoc.server.IdcServerThread
    Server Port: 16204
    Request Client Authentication: Yes
    Require Client Authentication: Yes
    Keystore File Path: /ucmapp/wlserver_10.3/server/lib/DemoIdentity.jks
    Alias: RIDCTest
    Truststore File Path: /ucmapp/wlserver_10.3/server/lib/DemoTrust.jks
    we are using the following Ports
    Server Port = 16204
    SSL Server Port = 16302
    Intradoc Port = 9999
    Somebody let us know if we are going somewhere wrong.
    Thanks in Advance

    Just to verify you do not have your own router/gateway correct? Your computer either connects directly into the wall or into a box provided by the ISP?
    Router/gateways stop incoming requests. And if it is yours then you have to figure out how to configure it so it allows those requests through.
    But presuming that you do not....
    Again i wanna make it clear that nobdy is able to ping
    my machine and i am also not able to ping any
    ipaddress whether it be yahoo or anything else. But i
    am able to access every site (ofcourse through
    browser) and i am also able to use every application
    which is using custom ports.
    Get ethereal. Play with it a bit. Use your browser and capture what occurs so you know what is going on.
    Then have someone ping you while running.
    I suspect you will not see the ping packet.
    What this means is that your ISP is blocking all incoming socket connection requests. You solution is ....
    - Get them to open the ports up
    - Get a different ISP.
    The problem : nobdy is able to connect to the server
    writen by me in java.
    Also the client and the server are diferent. The
    server waits for incoming client requests (using
    sock.accept() ) while the client simply tries to
    connect to server through the constructor
    'Socket(ipaddress, port)'.Yes, but in one case your machine connects to something while in the other something connects to it.
    One thing is clear from all this that the path to
    server is not getting resolved whether i try to
    connect to the server using my client or the browser
    or any other application which tries to connect to an
    ipaddress on a particular port.
    Resolved? Resolution only occurs when you use a domain name. There is no resolution when an IP is being used. You are using an IP for all of your testing correct?

  • Urgent help required for configuring forms server 6.0

    Hi every one/anyone
    i will really appreciate if i can get your attention and a little
    bit of your help in configuration of Developer Server.
    i have similar kind of a problem i hopeany one can shed some
    light on it as well.
    I am using
    Pentium III 450 MHZ 256 MB Ram
    NT server 4.0 with Service pack 3.
    Oracle 8.1.5
    IIS 4 or OAS 4.0.7
    Developer 6.0 down loaded from OTN.
    Internet Explorer 5.
    I have failed to run forms 6.0 on the web, i have tried all the
    option
    JDK supplied with the Developer 6.0 Software on DOS prompt.
    Jinitiator 1.1.7.11
    When i run forms from the Designer they work But When i try them
    to run form the browser Every thing works the status bar
    of the Internet Explorer 5 says applet initialized but the forms
    do not show up. when i press the refresh button of the browser
    the status bar show applet running and a forms window appear's
    but with out showing the form. I have checked from the Java
    Console it shows the same error on and again with or without
    jinitiator. I have almost tried every setting.
    Oracle JInitiator version 1.1.7.11
    Using JRE version 1.1.7.11o
    User home directory = E:\WINNT\Profiles\Administrator
    Proxy Configuration: Manual Configuration
    Proxy:
    Proxy Overrides: <local>
    Opening http://an.ma/web/oracle/forms/engine/Main.class no proxy
    Opening http://an.ma/web/oracle/ewt/lwAWT/BufferedApplet.class
    Opening http://an.ma/web/oracle/ewt/popup/PopupApplet.class
    Opening http://an.ma/web/oracle/ewt/popup/PopupOwner.class
    Opening http://an.ma/web/oracle/ewt/event/tracking/MouseGrabPr
    ovider.class
    Opening http://an.ma/web/oracle/ewt/help/HelpCapable.class
    Opening http://an.ma/web/oracle/ewt/lwAWT/ImmediatePainter.class
    Opening http://an.ma/web/oracle/ewt/lwAWT/DoubleBufferer.class
    Opening http://an.ma/web/oracle/ewt/lwAWT/VirtualComponent.class
    Opening http://an.ma/web/oracle/ewt/lwAWT/FocusRoot.class
    Opening http://an.ma/web/oracle/ewt/lwAWT/KeyProcessor.class
    Opening http://an.ma/web/oracle/forms/test/Test.class
    Opening http://an.ma/web/oracle/ewt/painter/PaintContext.class
    Opening http://an.ma/web/oracle/ewt/lwAWT/LWComponent.class
    Opening http://an.ma/web/oracle/forms/ui/mdi/MDIContainer.class
    Opening http://an.ma/web/oracle/ewt/lwAWT/lwMenu/LWMenuBar.class
    Opening
    http://an.ma/web/oracle/ewt/lwAWT/lwMenu/BaseMIContainer.class
    Opening
    http://an.ma/web/oracle/ewt/lwAWT/lwMenu/LWMenuItemContainer.clas
    s
    Opening http://an.ma/web/oracle/ewt/lwAWT/lwMenu/LWMenu.class
    Opening http://an.ma/web/oracle/ewt/lwAWT/lwMenu/LWMenuItem.class
    Opening
    http://an.ma/web/oracle/ewt/lwAWT/AbstractPainterComponent.class
    Opening
    http://an.ma/web/oracle/ewt/lwAWT/lwMenu/LWMenuInvoker.class
    Opening
    http://an.ma/web/oracle/ewt/lwAWT/lwMenu/LWPopupMenu.class
    Opening
    http://an.ma/web/oracle/ewt/lwAWT/lwMenu/LWMenuSeparator.class
    Opening http://an.ma/web/oracle/ewt/lwAWT/lwWindow/Desktop.class
    Opening http://an.ma/web/oracle/forms/ui/mdi/MDIWindowMenu.class
    Opening
    http://an.ma/web/oracle/ewt/lwAWT/lwMenu/LWPopupMenuListener.clas
    s
    Opening http://an.ma/web/oracle/ewt/popup/PopupFrame.class
    Opening http://an.ma/web/oracle/ewt/lwAWT/BufferedFrame.class
    Opening http://an.ma/web/oracle/ewt/painter/Painter.class
    Opening http://an.ma/web/oracle/ewt/popup/PopupHandler.class
    Opening http://an.ma/web/oracle/ewt/UIManager.class
    Opening
    http://an.ma/web/oracle/ewt/UIManager$LookAndFeelInfo.class
    Opening http://an.ma/web/oracle/ewt/LookAndFeel.class
    Opening
    http://an.ma/web/oracle/bali/share/collection/StringKey.class
    Opening http://an.ma/web/oracle/ewt/laf/oracle/OracleLookAndFe
    el.class
    Opening http://an.ma/web/oracle/ewt/laf/basic/BasicLookAndFeel
    .class
    Opening http://an.ma/web/oracle/ewt/painter/BorderPainter.clas s
    Opening http://an.ma/web/oracle/ewt/ColorScheme.class
    Opening http://an.ma/web/oracle/ewt/laf/oracle/OracleColorSche
    me.class
    Opening http://an.ma/web/oracle/ewt/UIDefaults.class
    Opening http://an.ma/web/oracle/ewt/HashTableDefaults.class no
    proxy
    Opening http://an.ma/web/oracle/ewt/MultiUIDefaults.class no
    proxy
    Opening http://an.ma/web/oracle/ewt/laf/basic/ColorizingFilter
    .class
    Opening http://an.ma/web/oracle/ewt/lwAWT/VComponentPaintConte
    xt.class
    Opening http://an.ma/web/oracle/ewt/painter/ImagePainter.class
    Opening http://an.ma/web/oracle/ewt/painter/AbstractPainter.cl
    ass
    Opening http://an.ma/web/oracle/ewt/laf/basic/PerComponentUIIn
    stantiator.class
    Opening http://an.ma/web/oracle/ewt/UIInstantiator.class no
    proxy
    Opening http://an.ma/web/oracle/ewt/plaf/StatusBarUI.class no
    proxy
    Opening http://an.ma/web/oracle/ewt/plaf/ComponentUI.class no
    proxy
    Opening http://an.ma/web/oracle/ewt/laf/oracle/OracleStatusBar
    Painter.class
    Opening http://an.ma/web/oracle/ewt/painter/AbstractBorderPain
    ter.class
    Opening http://an.ma/web/oracle/ewt/painter/AbstractWrappingPa
    inter.class
    Opening http://an.ma/web/oracle/ewt/painter/NullPainter.class
    Opening http://an.ma/web/oracle/ewt/laf/oracle/OracleUIUtils.c
    lass
    Opening http://an.ma/web/oracle/ewt/graphics/ImageSet.class no
    proxy
    Opening http://an.ma/web/oracle/ewt/lwAWT/DoubleBuffer.class
    Opening http://an.ma/web/oracle/ewt/plaf/TextUI.class
    Opening http://an.ma/web/oracle/ewt/laf/oracle/OracleInsetBord
    erPainter.class
    Opening http://an.ma/web/oracle/ewt/painter/FixedBorderPainter
    .class
    Opening http://an.ma/web/oracle/ewt/util/ImmInsets.class no
    proxy
    Opening http://an.ma/web/oracle/ewt/plaf/ToolBarUI.class no
    proxy
    Opening http://an.ma/web/oracle/ewt/laf/oracle/OracleToolBarPa
    inter.class
    Opening http://an.ma/web/oracle/ewt/laf/oracle/ScrollBoxBorder
    Painter.class
    Opening http://an.ma/web/oracle/ewt/laf/oracle/DisabledBGPaint
    er.class
    Opening http://an.ma/web/oracle/ewt/painter/ColorChange.class
    Opening http://an.ma/web/oracle/ewt/painter/FilledRectPainter.
    class
    Opening http://an.ma/web/oracle/ewt/painter/FGBGColorChange.cl
    ass
    Opening http://an.ma/web/oracle/ewt/laf/oracle/OracleRoundedPa
    inter.class
    Opening http://an.ma/web/oracle/ewt/graphics/SynthesizingImage
    Set.class
    Opening http://an.ma/web/oracle/ewt/graphics/NullImageFilter.c
    lass
    Opening http://an.ma/web/oracle/ewt/painter/ImageSetPainter.cl
    ass
    Opening http://an.ma/web/oracle/ewt/painter/TextPainter.class
    Opening http://an.ma/web/oracle/ewt/painter/TruncatingTextPain
    ter.class
    Opening http://an.ma/web/oracle/ewt/laf/basic/DisablingPainter
    .class
    Opening http://an.ma/web/oracle/ewt/laf/basic/StringInstantiat
    or.class
    Opening http://an.ma/web/oracle/ewt/UIDefaults$DeferredValue.c
    lass
    Opening http://an.ma/web/oracle/ewt/laf/basic/SingletonUIInsta
    ntiator.class
    Opening http://an.ma/web/oracle/ewt/lwAWT/SharedPainter.class
    Opening http://an.ma/web/javax/swing/JInternalFrame.class no
    proxy
    Opening http://an.ma/web/oracle/ewt/util/LocaleUtils.class no
    proxy
    Opening http://an.ma/web/oracle/ewt/util/WindowUtils.class no
    proxy
    Opening http://an.ma/web/oracle/ewt/util/WindowUtils$ActiveWin
    dowTracker.class
    Opening http://an.ma/web/oracle/forms/engine/MainBeanInfo.clas s
    Opening http://an.ma/web/sun/beans/infos/MainBeanInfo.class no
    proxy
    Opening http://an.ma/web/oracle/ewt/lwAWT/BufferedAppletBeanIn
    fo.class
    Opening http://an.ma/web/sun/beans/infos/BufferedAppletBeanInf
    o.class
    Opening http://an.ma/web/oracle/ewt/popup/PopupAppletBeanInfo.
    class
    Opening http://an.ma/web/sun/beans/infos/PopupAppletBeanInfo.c
    lass
    Opening http://an.ma/web/oracle/ewt/help/HelpProvider.class no
    proxy
    Opening http://an.ma/web/oracle/ewt/event/AnyEventListener.cla
    ss
    Opening http://an.ma/web/oracle/forms/ui/FormMouseGrabProvider
    .class
    Opening http://an.ma/web/oracle/ewt/event/tracking/GlassMouseG
    rabProvider.class
    Opening http://an.ma/web/oracle/ewt/lwAWT/lwWindow/DesktopCont
    ainer.class
    Opening http://an.ma/web/oracle/forms/engine/Runform.class no
    proxy
    Opening http://an.ma/web/oracle/forms/engine/MessageHandler.cl
    ass
    Opening http://an.ma/web/oracle/forms/registry/MessageManager.
    class
    Opening http://an.ma/web/oracle/ewt/lwAWT/lwWindow/LWWindow.cl
    ass
    Opening http://an.ma/web/oracle/ewt/event/tracking/KeyFilterPr
    ovider.class
    Opening http://an.ma/web/oracle/ewt/lwAWT/lwWindow/DesktopEven
    t.class
    Opening http://an.ma/web/oracle/ewt/event/EwtEvent.class no
    proxy
    Opening http://an.ma/web/oracle/ewt/EwtComponent.class
    Opening http://an.ma/web/oracle/ewt/scrolling/Scrollable.class
    Opening http://an.ma/web/oracle/ewt/dnd/Autoscroll.class no
    proxy
    Opening http://an.ma/web/oracle/ewt/event/tracking/GlassMouseG
    rabProvider$Proxy.class
    Opening http://an.ma/web/oracle/ewt/laf/generic/GenericLookAnd
    Feel.class
    Opening http://an.ma/web/oracle/ewt/laf/generic/SystemColorSch
    eme.class
    Opening http://an.ma/web/oracle/ewt/laf/generic/FixedColorSche
    me.class
    Opening http://an.ma/web/oracle/forms/engine/icons/splash.gif
    Opening http://an.ma/web/oracle/ewt/graphics/ImageUtils.class
    Opening http://an.ma/web/oracle/ewt/graphics/ImageLoader.class
    Opening http://an.ma/web/oracle/forms/engine/Splashscreen.clas s
    Opening http://an.ma/web/oracle/ewt/lwAWT/LWComponent$PaintCtx
    t.class
    Opening http://an.ma/web/oracle/ewt/laf/generic/GenericInsetBo
    rderPainter.class
    Opening http://an.ma/web/oracle/ewt/laf/generic/GenericRectang
    lePainter.class
    Opening http://an.ma/web/oracle/ewt/laf/generic/GenericDesktop
    UI.class
    Opening http://an.ma/web/oracle/ewt/laf/basic/BasicComponentUI
    .class
    Opening http://an.ma/web/oracle/ewt/laf/basic/AbstractComponen
    tUI.class
    Opening http://an.ma/web/oracle/ewt/plaf/DesktopUI.class no
    proxy
    Opening http://an.ma/web/oracle/ewt/lwAWT/lwWindow/WindowManag
    er.class
    Opening http://an.ma/web/oracle/ewt/lwAWT/lwWindow/laf/BaseWin
    dowManager.class
    Opening http://an.ma/web/oracle/ewt/lwAWT/lwWindow/DesktopList
    ener.class
    Opening http://an.ma/web/oracle/ewt/lwAWT/lwWindow/laf/MouseWi
    ndowActivater.class
    Opening http://an.ma/web/oracle/ewt/lwAWT/lwWindow/laf/KeyWind
    owActivater.class
    Opening http://an.ma/web/oracle/ewt/lwAWT/lwWindow/ModalStyle.
    class
    Opening http://an.ma/web/oracle/ewt/lwAWT/lwWindow/LWWindow$Fo
    cusTransferComp.class
    Opening http://an.ma/web/oracle/ewt/event/tracking/TrackingUti
    ls.class
    Opening http://an.ma/web/oracle/ewt/lwAWT/lwWindow/DesktopCont
    ainer$WindowEnum.class
    Opening http://an.ma/web/oracle/ewt/event/ListenerManager.clas s
    Opening http://an.ma/web/oracle/ewt/lwAWT/lwWindow/DesktopLayo
    ut.class
    Opening http://an.ma/web/oracle/ewt/laf/generic/GenericCompone
    ntUI.class
    Opening http://an.ma/web/oracle/ewt/scrolling/ScrollableExcept
    ion.class
    Opening http://an.ma/web/oracle/forms/ui/mdi/ActivationTracker
    .class
    Opening http://an.ma/web/oracle/ewt/lwAWT/lwMenu/ScrollableAda
    pter.class
    Opening http://an.ma/web/oracle/ewt/scrolling/arrowBox/ArrowBo
    x.class
    Opening http://an.ma/web/oracle/ewt/laf/generic/GenericMenuBar
    UI.class
    Opening http://an.ma/web/oracle/ewt/plaf/MenuBarUI.class no
    proxy
    Opening http://an.ma/web/oracle/ewt/lwAWT/lwMenu/laf/MenuBarCo
    ntroller.class
    Opening http://an.ma/web/oracle/ewt/lwAWT/lwMenu/PreferredRowL
    ayout.class
    Opening http://an.ma/web/oracle/ewt/lwAWT/lwMenu/BaseMIContain
    er$AddLsnr.class
    Opening http://an.ma/web/oracle/ewt/lwAWT/lwMenu/LWPopupMenuEv
    ent.class
    Opening http://an.ma/web/oracle/ewt/popup/NoPopupOwnerExceptio
    n.class
    Opening http://an.ma/web/oracle/ewt/laf/generic/GenericPopupMe
    nuUI.class
    Opening http://an.ma/web/oracle/ewt/plaf/PopupMenuUI.class no
    proxy
    Opening http://an.ma/web/oracle/ewt/lwAWT/lwMenu/laf/PopupMenu
    Controller.class
    Opening http://an.ma/web/oracle/ewt/lwAWT/lwMenu/PreferredColu
    mnLayout.class
    Opening http://an.ma/web/oracle/forms/engine/RunformBundle_en_
    US.class
    Opening http://an.ma/web/oracle/forms/engine/RunformBundle.cla
    ss
    Opening http://an.ma/web/oracle/forms/engine/RunformBundle_en.
    class
    Opening http://an.ma/web/oracle/ewt/laf/generic/GenericMenuIte
    mUI.class
    Opening http://an.ma/web/oracle/ewt/plaf/MenuItemUI.class no
    proxy
    Opening http://an.ma/web/oracle/ewt/lwAWT/lwMenu/laf/MenuItemC
    ontroller.class
    Opening http://an.ma/web/oracle/ewt/painter/AndOrStatePainterS
    witcher.class
    Opening http://an.ma/web/oracle/ewt/painter/AbstractPainterSwi
    tcher.class
    Opening http://an.ma/web/oracle/ewt/painter/DirectionalBorderP
    ainter.class
    Opening http://an.ma/web/oracle/ewt/lwAWT/lwMenu/laf/KeyStroke
    Painter.class
    Opening http://an.ma/web/oracle/ewt/lwAWT/lwMenu/laf/MenuItemP
    ainter.class
    Opening http://an.ma/web/oracle/ewt/lwAWT/lwMenu/laf/MenuSelCo
    lorChange.class
    Opening http://an.ma/web/oracle/ewt/laf/generic/GenericSelecti
    onPainter.class
    Opening http://an.ma/web/oracle/ewt/lwAWT/lwMenu/laf/MenuSelTe
    xtColorChange.class
    Opening http://an.ma/web/oracle/ewt/lwAWT/lwMenu/DragRedispatc
    her.class
    Opening http://an.ma/web/oracle/ewt/laf/generic/GenericMenuSep
    aratorUI.class
    Opening http://an.ma/web/oracle/ewt/plaf/MenuSeparatorUI.class
    Opening http://an.ma/web/oracle/ewt/lwAWT/lwMenu/LWCheckboxMen
    uItem.class
    Opening http://an.ma/web/oracle/ewt/thread/Task.class
    Opening http://an.ma/web/oracle/ewt/laf/generic/GenericMenuUI.
    class
    Opening http://an.ma/web/oracle/ewt/plaf/MenuUI.class
    Opening http://an.ma/web/oracle/ewt/lwAWT/lwMenu/laf/SubmenuIc
    on.class
    Opening http://an.ma/web/oracle/ewt/painter/PainterJoiner.clas s
    Opening http://an.ma/web/oracle/forms/engine/icons/bgnd.gif no
    proxy
    Opening http://an.ma/web/oracle/ewt/painter/FixedImagePainter.
    class
    Opening http://an.ma/web/oracle/ewt/lwAWT/lwMenu/laf/HorzMenuC
    ontroller.class
    Opening http://an.ma/web/oracle/ewt/lwAWT/lwMenu/LWMenuBar$Acc
    elFilter.class
    Opening http://an.ma/web/oracle/ewt/event/tracking/GlassMouseG
    rabProvider$Disp.class
    Opening http://an.ma/web/oracle/forms/handler/UICommon.class
    Opening http://an.ma/web/oracle/forms/handler/IHandler.class
    Opening http://an.ma/web/oracle/forms/api/IObject.class no
    proxy
    Opening http://an.ma/web/oracle/forms/handler/FormWindow.class
    Opening http://an.ma/web/oracle/forms/engine/RunformException.
    class
    Opening http://an.ma/web/oracle/forms/net/Connection.class no
    proxy
    Opening http://an.ma/web/oracle/forms/engine/MessageHandler2.c
    lass
    Opening http://an.ma/web/oracle/forms/engine/FlushQueue.class
    Opening http://an.ma/web/oracle/ewt/util/ClipboardProxy.class
    Opening http://an.ma/web/oracle/forms/engine/Registry.class no
    proxy
    Opening http://an.ma/web/oracle/forms/registry/Registry.dat no
    proxy
    Opening http://an.ma/web/oracle/forms/registry/default.dat no
    proxy
    Opening http://an.ma/web/oracle/forms/net/SocketConnection.cla
    ss
    Opening http://an.ma/web/oracle/forms/net/EncryptedOutputStrea
    m.class
    Opening http://an.ma/web/oracle/forms/net/EncryptedInputStream
    .class
    Opening http://an.ma/web/oracle/forms/net/StreamMessageReader.
    class
    Opening http://an.ma/web/oracle/forms/net/StreamMessageWriter.
    class
    Opening http://an.ma/web/oracle/forms/engine/Message.class no
    proxy
    Opening http://an.ma/web/oracle/forms/engine/TerminalMessage.c
    lass
    Opening http://an.ma/web/oracle/forms/engine/IndexTag.class no
    proxy
    Opening http://an.ma/web/oracle/forms/net/SingleAccessorQueue.
    class
    Opening http://an.ma/web/oracle/forms/engine/DeleteMask.class
    Opening http://an.ma/web/oracle/forms/engine/FontEntry.class
    Forms Applet version is : 4
    Opening http://an.ma/web/oracle/forms/engine/DeferredMessage.c
    lass
    when i press refresh on the ie5 then it says applet started
    creates a window inside the browser with borders
    but does now show any thing expect a few more lines in the
    console window as following
    Opening http://an.ma/web/oracle/ewt/util/StringUtils.class
    Opening http://an.ma/web/oracle/ewt/lwAWT/BufferedPanel.class
    Opening http://an.ma/web/oracle/ewt/popup/PopupPanel.class
    Opening
    http://an.ma/web/oracle/ewt/lwAWT/WaitingDoubleBuffer.class
    Opening
    http://an.ma/web/oracle/ewt/lwAWT/BalkingDoubleBuffer.class
    Opening http://an.ma/web/oracle/ewt/graphics/GraphicUtils.class
    Opening http://an.ma/web/oracle/ewt/util/ComponentUtils.class
    Opening
    http://an.ma/web/oracle/ewt/layout/DirectionalLayout.class
    I hope any one can help me. I have been trying to run this thing
    for almost 2 months.
    bye
    null

    I had the same problem for the longest time... The problem is
    the "SplashScreen" it hangs everything up...
    My solution was add this line to your html:
    <param name="splashScreen" value="no">
    Good luck,
    Let me know if that works..
    Jeff.
    mobeen (guest) wrote:
    : Hi every one/anyone
    : i will really appreciate if i can get your attention and a
    little
    : bit of your help in configuration of Developer Server.
    : i have similar kind of a problem i hopeany one can shed some
    : light on it as well.
    : I am using
    : Pentium III 450 MHZ 256 MB Ram
    : NT server 4.0 with Service pack 3.
    : Oracle 8.1.5
    : IIS 4 or OAS 4.0.7
    : Developer 6.0 down loaded from OTN.
    : Internet Explorer 5.
    : I have failed to run forms 6.0 on the web, i have tried all
    the
    : option
    : JDK supplied with the Developer 6.0 Software on DOS prompt.
    : Jinitiator 1.1.7.11
    : When i run forms from the Designer they work But When i try
    them
    : to run form the browser Every thing works the status bar
    : of the Internet Explorer 5 says applet initialized but the
    forms
    : do not show up. when i press the refresh button of the browser
    : the status bar show applet running and a forms window appear's
    : but with out showing the form. I have checked from the Java
    : Console it shows the same error on and again with or without
    : jinitiator. I have almost tried every setting.
    : Oracle JInitiator version 1.1.7.11
    : Using JRE version 1.1.7.11o
    : User home directory = E:\WINNT\Profiles\Administrator
    : Proxy Configuration: Manual Configuration
    : Proxy:
    : Proxy Overrides: <local>
    : I hope any one can help me. I have been trying to run this
    thing
    : for almost 2 months.
    : bye
    null

  • Help required on configuring Auto Login...!

    Hi All,
    I'm using SUn ONE Webserver Service Pack 9. And once after starting my Web Server instance and when ever I invoke my application url (http://localhost:8080/) It automatically takes me inside the application. I need to remove this auto login configuration. Because whenever I use Logout and login using some other user_id. It still logs in as the same Auto login user name.
    Kindly help me.
    Thanks in advance.
    SAM

    Hi,
    I resolved the problem. It was too some more properties files which needs to be added to the app.
    Cheers
    SS

  • Help Required to configure GRC Work Inbox Type Not Found Error

    All .. I am new to the hands on part on GRC 10. Am trying to configure RM Work INbox. When I go through NWBC to Risk Asessments and try to create a Risk am getting the below error: Type _Not-Found Error for the transaction GRRM_POWL_RNP and GRRM _POWL_RESPONE. Have tried some of the suggestions on earlier threads e.g SICF etc. Appreciate your help to resolve

    Fernando . Thanks for the response. I am getting this error when I am trying to create a risk. Attached is the snapshot of the error. I have tried stuff like deleting the cache, checked SICF to see if Web Dyn Pro is active etc

  • Configuring Multicast for Video

    I have a WAN network with frame-relay link (bandwidth 256Kbps)and conected to one there is a Catalyst 3550 doing Inter-VLAN. the switch port conected to router is routing (no switchport) and all others ports of the switch are at VLAN 1 (default). The Video-conference Server is at VLAN 1. What are the basic requirements or requisites? Do I have to configure multicast routes (ip mroute)? Anybody have examples configurations? Thanks.

    The following URLs might help you:
    http://www.cisco.com/warp/public/473/94.html
    http://www.cisco.com/warp/public/473/38.html
    http://www.cisco.com/warp/public/473/22.html

  • Require to configure CUCM and Gateway router PRI for 200 users

    Hi all,
    My current scenario is like this:
    We have two CUCM servers(7.1) in reduandancy. One is publisher and other is subscriber. We have a gateway router 2921 with a single PRI card. We have 200 IP Phone users. Currently the problem is we have only 30 telephone lines. So with the help of DID configuration. We assign thirty ports to thirty users. Now these thirty users are able to to make an outbound call and recieve an Inbound call. Now I also want to create a pattern in which we dedicate 10 channaels for other 120 users to make an outbound call. And restrict 50 users to not make an outbound call. So we require such a scenario.
    Total 200 Users:
    1. First 30 users. Able to make an outbound call and also able to recieve an inbound call.
    2.  Next 120 Users. Able to make an outbound call. But not able to recieve an inbound call because of PRI restriction. Because we only have a thirty numbers. Dedicate 10 channels for them.
    3. Last 50 users. Not able to make an outbound call. And also not able to recieve an Inbound call.
    So I need a configurations of Gateway router and PRI. And also of CUCM in which we could define such a pattern.
    Regards,
    Ali Raza

    Ali,
    The outbound call restrictions can be implemented using the CUCM Calling Search Space configurations.  A basic example to illustrate:
    Partition 1:  internal_pt   (only internal patterns)
    Partition 2: phones_pt (ip phones on your network)
    Partition 3: pstn_pt (off net patterns/external)
    CSS1: Offnet_css
    internal_pt
    phones_pt
    pstn_pt
    CSS2: Onnet_css
    internal_pt
    phones_pt
    You place all patterns that can reach off net in "pstn_pt". Phones that are using CSS2 cannot reach off net.  The above example is leveraging the device CSS for all call routing decisions.Using this approach, you would assign "onnet_css" to phones that can only dial internally. NOTE: I am just using a basic example here and not suggesting you use this PT/CSS config "as is".
    There is another approach where you "allow" all patterns on a device and "restrict" on the line. For example:
    Partition 1:  internal_pt   (only internal patterns)
    Partition 2: phones_pt (ip phones on your network)
    Partition 3: pstn_pt (off net patterns/external)
    Partition 4: block-pstn_pt (blocking patterns for pstn)
    CSS1: AllPhones_css
    internal_pt
    phones_pt
    pstn_pt
    CSS2: restrict-pstn_css
    block-pstn_pt
    Again, pstn_pt contains all pstn patterns.  The block-pstn_pt would also contain off net patterns. The difference is that in the block-pstn_pt all patterns would have the "Block this pattern" flag enabled. All phones would have a Device Level CSS of AllPhones_css.  Phone lines where you wanted to restrict off net dialing would have a Line Level CSS of restrict-pstn_css.
    Just a quick refresher, when a phone LINE goes off hook to dial the CUCM is using the "Line Level CSS" + "Device Level CSS" to make the routing decision.  So, assume Line 1 on Phone A has restrict-pstn_css and the phone Device Level CSS is AllPhones_CSS. The Effective Search Space is:
    1. block-pstn_pt
    2. internal_pt
    3. phones_pt
    4. pstn_pt
    So, if we assume that block-pstn_pt contains patterns that override patterns in pstn_pt then you can effectively block off net access to Phone A, Line 1.
    Why would this be a good approach?  Well, what if you had a need to restrict Line 1 on Phone A but allow Line 2 on Phone A.  Using line level restrictions is much more flexible. Especially if you have more than 2 options you need to consider.
    As far as inbound restrictions. If a phone line doesn't have a DID then you have achieved your objective.
    The part I can't answer is reserving 10 specific channels for one group of users. I do not believe this is possible.
    HTH.
    Regards,
    Bill

  • Multicast routing issues when a subinterface is configured

    Strange issue here. Cisco and the vendor are unable to help so far...
    Most of our layer 3 lives on core switches. However, we have  a couple sites off our WAN connected via  Cisco routers. In these offices, we can not get paging to work.
    I  setup a lab and have finally determined what is at least causing the  issue. My lab "branch" has  the same problems, but I can resolve the  problem by removing the sub-interface off the router.
    On my LAN side  of the router, with this  config, everything works fine.
    #--- THIS WORKS ---#
    R1#
    ip pim rp-address 192.168.251.254
    gig 0/0 (connects to SW1 g0/1)
     ip address 10.254.253.254 255.255.255.0
     ip pim sparse-dense mode
    SW1#
     gig 0/1 (connects to R1 g0/0)
     !no config - default VLAN1
    When I apply this config...everything breaks. The phone goes off
    #--- THIS DOES NOT WORK ---#
    R1#
    ip pim rp-address 192.168.251.254
    gig 0/0 (connects to SW1 g0/1)
     no ip
    gig 0/0.777 (connects to SW1 g0/1)
     ip address 10.254.253.254 255.255.255.0
     ip pim sparse-dense mode
    SW1#
     gig 0/1 (connects to R1 g0/0)
     sw mode trunk
     sw trunk  encap dot1q
    int vlan 777
     ip address 10.254.253.1 255.255.255.0
     ip pim sparse-dense mode
    int vlan 778
     ip address 10.254.251.1 255.255.255.0
     ip pim sparse-dense mode
     gig 0/17 (phone port)
     switch access vlan 778 (keeping it simple for now)
    I have tried this on 2 different model routers, each with different IOS versions.  The same issues follow each router. What is it about the  sub interfaces?
    Any insight? Calling all multicast experts! Thanks!

    Hi,
    creating sub-interface should not create any difference here. Only difference i can see earlier switch was working in l2 mode now it is participating in multicast routing as SVI is configured and pim neighborship established. Have you configured RP address on SW1. Please share below outputs from both devices
    - running config
    - show ip mroute <group>
    - show ip pim rp address mapping
    Regards,
    Akash

  • Help required in Weblogic 6 - Creation & Configuration of Web Application

    Forum Home > Enterprise JavaBeans[tm]
    Topic: Help required in Weblogic 6 - Creation & Configuration of Web Application
    Duke Dollars
    2 Duke Dollars assigned to this topic. Reward the best responses to your question
    using the icons below, or transfer additional Duke Dollars to this topic.
    Welcome moinshariff!
    Watching this topic.
    Previous Topic Next Topic
    This topic has 1 reply on 1 page (Most recent message: Jan 23, 2002 1:05 AM)
    Author: moinshariff Jan 22, 2002 4:55 AM
    Hi,
    I am using Weblogic 6. I have created a new Web
    Application called Web (I have not used the DefaultWebApp_myserver).
    And I have the following settings:
    Name : Web
    URI : Web
    and Path : C:\Web
    and placed my JSP files under c:\Web\
    I am able to access the first page, but after that I am not able to access the
    second page.
    I get "Error 404--Not Found" on the browser. Basically the class file is not getting
    created under /Web-inf/_tmp_war_myserver_myserver_Web/jsp_servlet/ folder .
    I tried a work around for this. I copied all my files under one more folder called
    web and placed this under C:\Web
    The it works. Now I have 2 copied off all the files, 1 copy under c:\web and another
    copy under c:\web\web\.
    If I have the files under DefaultWebApp_myserver and have the setting as
    Name: DefaultWebApp_myserver
    URI: DefaultWebApp_myserver
    Path: .\config\mydomain\applications
    everything works fine.
    Can any one please let me know if there is any configuration which has to be done
    so that I do not duplicate the code in 2 directories
    Thanks in advance.
    Regards,
    Moin

    Forum Home > Enterprise JavaBeans[tm]
    Topic: Help required in Weblogic 6 - Creation & Configuration of Web Application
    Duke Dollars
    2 Duke Dollars assigned to this topic. Reward the best responses to your question
    using the icons below, or transfer additional Duke Dollars to this topic.
    Welcome moinshariff!
    Watching this topic.
    Previous Topic Next Topic
    This topic has 1 reply on 1 page (Most recent message: Jan 23, 2002 1:05 AM)
    Author: moinshariff Jan 22, 2002 4:55 AM
    Hi,
    I am using Weblogic 6. I have created a new Web
    Application called Web (I have not used the DefaultWebApp_myserver).
    And I have the following settings:
    Name : Web
    URI : Web
    and Path : C:\Web
    and placed my JSP files under c:\Web\
    I am able to access the first page, but after that I am not able to access the
    second page.
    I get "Error 404--Not Found" on the browser. Basically the class file is not getting
    created under /Web-inf/_tmp_war_myserver_myserver_Web/jsp_servlet/ folder .
    I tried a work around for this. I copied all my files under one more folder called
    web and placed this under C:\Web
    The it works. Now I have 2 copied off all the files, 1 copy under c:\web and another
    copy under c:\web\web\.
    If I have the files under DefaultWebApp_myserver and have the setting as
    Name: DefaultWebApp_myserver
    URI: DefaultWebApp_myserver
    Path: .\config\mydomain\applications
    everything works fine.
    Can any one please let me know if there is any configuration which has to be done
    so that I do not duplicate the code in 2 directories
    Thanks in advance.
    Regards,
    Moin

  • Please help me in configuring a Cisco 2800 series router!

    Hi! I have to configure a new router with a static route. No routing protocol will be used. I just have to set default route on it and NAT. My senior Network Engineer has asked me to configure this router. There's an apartment where our Overseas employees stay, earlier this apartment had a broadband connection which was further divided through the APs(Cisco Wireless Access Points) and made usable to around 20 users. Now, they have bought in their own lease line and I have to configure this router. We just have to connect it with the ISP using Ethernet (not serial link). I would be so so grateful if you can just type in complete configuration for this. Thanks a ton in advance!

    Hi There,
    Thanks for your great help! 
    Below is the final template which my NE provided me:
    Now I have to configure this router and then further need to connect various workstations with the same network. Please let me know what needs to be done further.
    Thanks!
    Configuration:::
    service timestamps debug datetime msec
    service timestamps log datetime msec
    service password-encryption
    ip domain-name CVT.net
    logging buffered 128000 informational
    logging console errors
    logging monitor notifications
    no aaa new-model
    clock timezone IST 5 30
    ip cef
    no ip domain lookup
    username aptadmin secret 
    enable secret 
    crypto key generate rsa
    ip ssh time-out 60
    ip ssh authentication-retries 2
    ip ssh version 2
    service dhcp
    ip dhcp pool LAN-POOL
    network 192.168.1.0 255.255.255.0
    default-router 192.168.1.1
    dns-server 8.8.8.8 4.2.2.2
    domain-name CVT.net
    lease 1
    interface FastEthernet0/0
     description *********Spectranet WAN*********
     ip address x.x.x.x 255.255.255.252
     load-interval 30
     duplex full
     speed 100
     ntp disable
     no cdp enable
    interface FastEthernet0/1
     description Connect to LAN 
     ip address 192.168.1.0 255.255.255.0
     no ip redirects
     duplex auto
     speed auto
     ntp disable
    ip forward-protocol nd
    no ip http server
    no ip https server
    control-plane
    banner exec $
                      Network Provided by CVT
    This system is restricted to authorized individuals. Unauthorized access is a
    criminal violation of the law and is subject to prosecution. Please disconnect
    if you are not an authorized individual. Otherwise, you will be prosecuted 
    to the full extent of State and Federal law.
    All connections and changes are logged.
    ************** Warning - Warning - Warning **************
    $
    banner login $
    Authorized Associates only! Please disconnect your connection if
    you are not an authorized Associate. Otherwise, you will be
    prosecuted to the full extent of State and Federal law.
    All connections and changes are logged.
    $
    line con 0
     exec-timeout 15 0
     password 7 
     login local
    line aux 0
     exec-timeout 15 0
     password 7 C@pt
     login local
    line vty 0 4
     access-class 50 in
     exec-timeout 5 0
     login local
     transport preferred ssh
     transport input ssh
    line vty 5 15
     access-class 50 in
     exec-timeout 5 0
     login local
     transport preferred ssh
     transport input ssh
    end

Maybe you are looking for