Help required in module insertion

Dear All,
I have 6509 switch. In its first slot present 10/100 ethernet module is there.
I have to remove this module and insert 10/100/1000 ethernet module.
Can I have some valid suggestions:
1 Like these are the precautions needs to be taken
2 Like These are the problems may occur, if this is the problem or error this is the solution or activity needs to be carried out
3 Like these are the check list we have to verify after insertion.
Your valid inputs are appreciated.
Regards
SKRAO

Hi SKRAO,
In my opinion, these are the best practices that you can follow :
1. Check the release notes of the IOS or catOS ruuning on the switch.
2. Check the minimum and cisco recommended IOS for the module.
3. Check the IOS on the Sup engine and then match it with the releasenotes..upgrade if required.
4. Then swap out the module as they support online insertion and removal so dont have to powe down yoru switch.
HTH, Please rate if it does.
-amit singh

Similar Messages

Help required for an insert logic

Hi
I need to create an insert logic in the following way..
suppose my table has 20000 rows to insert in tab1 table
but due to very small undo table space size i need to insert small amount of rows between two commits..
say 20000/10 = 2000 rows i need to insert in the table in each commit.
so
for i in 1 .. 10 loop
insert into tab1 values act_data(i); --- here in each insert i need to insert 2000 rows
commit;
end loop;
act_data(i) is the collection containing whole data.
Hope i could express my problem
Thanks in advance.

You seem to already have a working answer to your question but your sample code contains one of the worse coding errors you could make.
Never commit inside a loop.
Committing every 2000 rows does much more (not in a good way) than make things slower ... read Tom Kyte's many comments about why this should not be done.
An insert from an array such as you seem to have should be done using FORALL.
http://www.morganslibrary.org/reference/array_processing.html#apfa

Required function module to get date one year in the past.

Hi,
Required function module to get date one year in the past.
Thanks and regards,
M.R.Reddy.

Hello,
You can check this:
DATA:
V_DATE1 TYPE D,
V_DATE2 TYPE D.
V_DATE1 = SY-DATUM.
TRY.
    CALL METHOD CL_HRPAD_DATE_COMPUTATIONS=>SUBTRACT_YEARS_FROM_DATE
      EXPORTING
        START_DATE = V_DATE1
        YEARS      = 1
      RECEIVING
        DATE       = V_DATE2.
CATCH CX_HRPA_VIOLATED_POSTCONDITION .
ENDTRY.
WRITE:
/ V_DATE1, / V_DATE2.
Hope this helps.
Br,
Suhas

Error "Invalid or Could not find module configuration" and "Required application module HyperionPlanning.planning is not configured

Dear
I use version 11.2.1, try to open an application one by planning and workspace is the error below.
"Invalid or Could not find module configuration" and "Required application module HyperionPlanning.planning is not configured"
I checked the oracle site, but the suggested solution is not possible because using the OHS and found the file HYSLWorkers.properties.
Solution
On the server que hosts the Apache component:
1. Navigate to HYPERION_HOME%% \ common \ httpServers \ Apache \ 2.0.59 \ conf
2. Edit the file named HYSLWorkers.properties,
3. Locate the entry starting with "worker.HP__8300.port"
4. Set its value to the value of the Planning web application's listening port incremented by two,
5. Save and close
6. Restart Apache only
Anyone have any suggestions?

If restarting the services does not help, run the EPM configurator again and configure foundation web server again then restart services and try logging into workspace
Cheers
John
http://john-goodwin.blogspot.com/

XSLT mapping Help Required.

XSLT mapping Help Required.
Hi Experts,
I am New to XSLT Mapping. I am practising the below Example:
InputXML File:
<?xml version="1.0" encoding="UTF-8"?>
<?xml-stylesheet type="text/xsl" href="Persons111.xsl"?>
<ns0:MT_XSLT_Source xmlns:ns0="http://XYZ.com/gen">
<Person>
<FirstName>Anshul</FirstName>
<LastName>Chowdhary</LastName>
<Gender>Male</Gender>
<Address>
<Street>2nd Main</Street>
<Houseno>83/b</Houseno>
<City>Mysore</City>
</Address> </Person>
</ns0:MT_XSLT_Source>
XSL StyleSheet File:
<?xml version='1.0' encoding="UTF-8"?>
<xsl:stylesheet version="1.0" xmlns:xsl="http://www.w3.org/1999/XSL/Transform" xmlns:ns0="http://XYZ.com/Gen"
Xmlns:ns1=”http://XYZ.com/Test”>
<xsl:template match="/">
<ns1:MT_XSLT_Target>
<Title> <xsl:value-of select="ns0:MT_XSLT_Source/Person/Gender"/> </Title>
<Name> <xsl:value-of select="concat(concat(ns0:MT_XSLT_Source/Person/FirstName,' '), ns0:MT_XSLT_Source/Person/LastName)"/>
</Name>
<Street> <xsl:value-of select="concat(concat(ns0:Mt_XSLT_Source/Person/Address/Houseno,' '),
ns0:Mt_XSLT_Source/Person/Address/Street)"/> </Street>
<City> <xsl:value-of select="ns0:Mt_XSLT_Source/Person/Address/City"/> </City>
</ns1:MT_XSLT_Target>
</xsl:template>
</xsl:stylesheet>
The Desired Output shuold be:
<?xml version="1.0" encoding="UTF-8"?>
<ns1:MT_XSLT_Target xmlns:ns1="http://XYZ.com/Test">
<Title>Male</Title>
<Name>Anshul Chowdhary</Name>
<Street>83/b 2nd Main</Street>
<City>Mysore</City>
</ns1:MT_XSLT_Target>
I have refered the xsl in xml and i am getting the below Oupt in a Single line like this:
Anshul Chowdhary Male 2nd Main 83/b Mysore
I am Unable to display in Target XML Fomrat as shown above. Please check and do the needful.
Regards,
GIRIDHAR

Hi,
I have used below for testing.
Input xml:
<?xml version="1.0" encoding="UTF-8"?>
<?xml-stylesheet type="text/xsl" href="Persons111.xsl"?>
<ns0:MT_XSLT_Source xmlns:ns0="http://XYZ.com/gen">
<Person>
<FirstName>Anshul</FirstName>
<LastName>Chowdhary</LastName>
<Gender>Male</Gender>
<Address>
<Street>2nd Main</Street>
<Houseno>83/b</Houseno>
<City>Mysore</City>
</Address> </Person>
</ns0:MT_XSLT_Source>
xsl code:
<?xml version='1.0' encoding="UTF-8"?>
<xsl:stylesheet version="1.0" xmlns:xsl="http://www.w3.org/1999/XSL/Transform" xmlns:ns0="http://XYZ.com/gen"
    xmlns:ns1="http://XYZ.com/Test">
    <xsl:output method="xml" version="1.0" encoding="UTF-8" indent="yes"/>
    <xsl:template match="/">
        <ns1:MT_XSLT_Target>
            <Title> <xsl:value-of select="ns0:MT_XSLT_Source/Person/Gender"/> </Title>
            <Name> <xsl:value-of select="concat(concat(ns0:MT_XSLT_Source/Person/FirstName,' '), ns0:MT_XSLT_Source/Person/LastName)"/>
            </Name>
            <Street> <xsl:value-of select="concat(concat(/ns0:MT_XSLT_Source/Person/Address/Houseno,' '),
                /ns0:MT_XSLT_Source/Person/Address/Street)"/> </Street>
            <City> <xsl:value-of select="/ns0:MT_XSLT_Source/Person/Address/City"/> </City>
        </ns1:MT_XSLT_Target>
    </xsl:template>
</xsl:stylesheet>
For testing in PI ,change the extension from .txt to .xsl and zip it and upload into PI as an imported archive .
Regards
Venkat

Urgent help required: Query regarding LC Variables

Hi All
Sometime earlier I was working on a performance issue raised by a customer. It was shell script that was taking almost 8-9 hrs to complete. During my research I came across a fact that there were some variables which were not set, the LC variables were impacting the sort funnel operations because of which the script was taking a long time to execute.
I asked them to export the following commands, after which the program went on smoothly and finished in a couple of mins:
export LC_COLLATE=en_US.ISO8859-1
export LC_MESSAGES=C
export LC_MONETARY=en_US.ISO8859-1
export LC_MONETARY=en_US.ISO8859-1
export HZ=100
export LC_CTYPE=en_US.ISO8859-1
export LANG=en_US.UTF-8
Later I did recover that setting the LC_COLLATE to C, is not helping and the program was again taking a lot of time. Few questions that I want to ask are:
1. Can someone please tell me, what each of these variable mean and how these values make a difference.
2. When I exported LC_COLLATE=en_US.ISO8859-1, it worked fine, but when i tried with the defalut value LC_COLLATE=C, then why the program didnt work.
As this issue is still going on, hence I would request All to provide their valuable inputs and let me know as much as possible.
Appreciate your help in this regard.
Thanks
Amit
Hi All
A new development in this regard. The customer has send us a screen shot in which they were trying to export the locale variable using the commands which I have pasted above. I can see in the screen shot that while exporting LC_COLLATE and LC_TYPE, they get a message that ""ksh: export: couldn't set locale correctly"".
Request everyone to please give their inputs as it's a bit urgent.
Thanks for all the help in advance.
Thanks
Amit
Some help required please...
Edited by: amitsinhaengg on Jul 22, 2009 2:03 AM
Edited by: amitsinhaengg on Jul 22, 2009 2:06 AM

LC_CTYPE
Controls the behavior of character handling functions.
LC_TIME
Specifies date and time formats, including month names, days of the week, and common full and abbreviated representations.
LC_MONETARY
Specifies monetary formats, including the currency symbol for the locale, thousands separator, sign position, the number of fractional digits, and so forth.
LC_NUMERIC
Specifies the decimal delimiter (or radix character), the thousands separator, and the grouping.
LC_COLLATE
Specifies a collation order and regular expression definition for the locale.
LC_MESSAGES
Specifies the language in which the localized messages are written, and affirmative and negative responses of the locale (yes and no strings and expressions).
You can use command
# locale -k LC_CTYPE
to see more detail about each type.

Help required - Sales order item is partially delivered but the item grayed

I have a sales order 123 having say item10 with qty 1, item20 with qty 10 , item 30 qty 12
Item 1 confirmed qty 1 and delivered qty is 1
Item 2 confirmed qty 10 and delivered qty 10
Item 3 confirmed qty 1 and delivered qty is 1
Now the item3 still has open requirements of 11 to be delivered. But the item is GRAYED OUT already.
even if I do ATP the qty is not confirming for the remaining 11 pieces.
Why is that? How to make that item out from GRAY.
How to confirm the remaining 11 qty for that item.
Help required as early as possible.
Appreciate ur help guys
Radha

hi Radha, how are you ?
     ---the partial deliveries in master data must have not been mentioned.
     ---the deliveries should be upto target quantity.
     ---check order type, item category and schedule line category.
     ---check unrestricted stock availability.
thank you
regards
Khera.

Calling search helps dynamically in module pool program

Hi Experts,
I have created two search helps. I need to call these search helps in my module pool program dynamically for a single field (i.e ZMATNR).
you might be known... if it is a single search help, we can assign that in field attributes.
But here... I need to call different search helps for a single field based on the condition.
Pls help me.
Thanks
Raghu

Hi,
Use the below function module and pass the search help created in search help field according to the condition.
Process on Value-request.
if condition = A.
call function " F4IF_FIELD_VALUE_REQUEST"
TABNAME           =
FIELDNAME        =
SEARCHHELP     = "Mention search help created
Elseif Conditon =B.
call function " F4IF_FIELD_VALUE_REQUEST"
TABNAME           =
FIELDNAME        =
SEARCHHELP     = "Mention search help created
Endif.
Regards,
Prabhudas

Search Help with in a serach help required in SRM 4.0

Hi,
Requirement: Search help required for Product Category field in the Search help for Product(BBPH_PRODUCT) in SRM portal.
This search help is used in Create shopping Cart transaction. The hyper link on Internal Goods/Services leads to the search help BBPH_PRODUCT.
My analysis:
The field Product Category (CATEGORY_ID) has search help(COM_CAT_HIER) attached to its data element. When I single test the search help BBPH_PRODUCT in SAP GUI,I can see the search help for field product category in the selection dialogue box. However the same does not appear on the corresponding screen in HTML.
Please let me know whether I need to do some thing to make the search help appear on the HTML screen?
With Regards,
Prakash Kamath

Hi Prakash,
I have the same problem but with another field. Unloading point. Could you please tell me how did you solve this problem with displaying F4 help on html/ SRM portal?
Thank you very much.
Best regards,
Danijela ZIvanovic

Help required in mapping MM pricing

PO should have conditions for
    freight
    Insurance
    bank charges
all paid to the vendor who is supplying goods.
These prices will have to be loaded on materials on GR.
2.
PO should not have any values against the conditions as mentioned above as he will not be paid for that.
When goods arrive, these charges are paid by local clearing agent or agents.
He will be paid accordingly based on the invoice he sends.
These costs also should be booked on material upon GR.
The local vendor or vendors does the clearing of goods at the port and for that he/they charge company and sends invoices.
Company wants to track these expenses per vendor and also wants different GL accounts for each type of conditions(heads of expenses these vendor/s charges in their invoice such as port charges, clearing charges,insurance charges,bank charges,freight where original supplier do not charge for these costs to the company)
Importantly,all these costs also have to be loaded on material .How this will be done ?
Consider also the case where you raised the PO with only conditions such as insurance and bank charges included in the PO and rest of the charges as mentioned above are borned by local vendor for clearing goods.
Now when I do the goods receipt the value will only get updated by the quantity*rate basis in mat master.
How can we load the values incurred for clearing the goods at the time of GR then ?
example: PO qty:100 @rate 10/ea
GR: Stock with MAP updated say as 10(no invoice yet from original supplier and also from the local clearing vendor)
Now these goods are transferred to other plant vide say STO or plant to plant transfer.
This material will also get updated with MAP as 10.
Now after couple of days the local vendor invoice comes and he is paid actually for the charges he claimed and also comes in the invoice of original goods supplier.
When these invoices will be posted how these costs will be added to the material ?
Can any one please suggest the best possible solution ASAP as am left with no time here.
Regards,
Manoj

Hi,
Your requirement is very common across all manufacturing comapanies.
1)Create seperate condition types for freight, insurance and bank charges with condition category as "B - Delivery costs"
2) flag the "accruals" check box.
3) Select the appropriate value for "Vendor in GR" field as per your requirement.
4) Insert these condition types in the calculation schema as per the requirement
5) Assign an accrual key. If the amount to be posted to different accounts, use different accrual keys.
6) maintain the "Actual Value" ( a sort of total of all conditon types used in the schema) in the schema such that it includes the values of above condtion types. Check value "S" is assigned in the "sub totals" field for "Actual Value" (if you are following standard JRM000, just insert your condition types before the "actual value" level)
Now your schema is ready. Since the values of freight, insurance and bank charges are included in "actual value", always the material will be loaded with this value at the time of GR.
Usually vendor code will be defaulted in the vendor field of the above condtion types. You can change the same at the time of PO creation by selecting the condition type and clicking on details icon.
You can post the vendor invoice for base value and taxes using the variant
"goods/service items" and post the other charges to different vendor account using "planned delivery costs" variant. if there are any differences between the planned value in the PO and actual invoice receipt, those are automatically adjusted.
If you require any further clarifications plz revert back
regards,
Mallik

Help required with Photoshop Elements 4.0 this has been installed on my new Toshiba laptop with windows 8.1 for some 18 months and operating well. Now it will not open, message pops up saying "attempt to access invalid address" then "application not respo

Help required with Photoshop Elements 4.0 this has been installed on my new Toshiba laptop with windows 8.1 for some 18 months and operating well. Now it will not open, message pops up saying “attempt to access invalid address” then “application not responding” Suggestions how to access would be much appreciated. Tks. Stuart

What is the size of your hard disk? PSE 4 is a very old program and I suspect it is not able to access the entire hard disk on your machine. Just a thought here.

Help require with installing Adobe Acrobat onto my Macbook Pro Retina.

Help require with installing Adobe Acrobat onto my Macbook Pro Retina.
I have successfully installed all of my creative cloud apps with the exception being acrobat.
I cannot print from Indesign to PDF.
I have unistalled, reinstalled and still no Adobe Acrobat.
I now have to go back to Windows 8 and create the PDF's there.
Any one know how to get around this issue?
Thanks in advance
Kelvin

OSX has effectively killed the ability to print to pdf, (print to pdf eliminates most of the "Rich features" of current pdf).
Export from InDesign, always, excpet for the 1% of the time where you know why print to pdf would produce a better result.

Help required in Weblogic 6 - Creation & Configuration of Web Application

Forum Home > Enterprise JavaBeans[tm]
Topic: Help required in Weblogic 6 - Creation & Configuration of Web Application
Duke Dollars
2 Duke Dollars assigned to this topic. Reward the best responses to your question
using the icons below, or transfer additional Duke Dollars to this topic.
Welcome moinshariff!
Watching this topic.
Previous Topic Next Topic
This topic has 1 reply on 1 page (Most recent message: Jan 23, 2002 1:05 AM)
Author: moinshariff Jan 22, 2002 4:55 AM
Hi,
I am using Weblogic 6. I have created a new Web
Application called Web (I have not used the DefaultWebApp_myserver).
And I have the following settings:
Name : Web
URI : Web
and Path : C:\Web
and placed my JSP files under c:\Web\
I am able to access the first page, but after that I am not able to access the
second page.
I get "Error 404--Not Found" on the browser. Basically the class file is not getting
created under /Web-inf/_tmp_war_myserver_myserver_Web/jsp_servlet/ folder .
I tried a work around for this. I copied all my files under one more folder called
web and placed this under C:\Web
The it works. Now I have 2 copied off all the files, 1 copy under c:\web and another
copy under c:\web\web\.
If I have the files under DefaultWebApp_myserver and have the setting as
Name: DefaultWebApp_myserver
URI: DefaultWebApp_myserver
Path: .\config\mydomain\applications
everything works fine.
Can any one please let me know if there is any configuration which has to be done
so that I do not duplicate the code in 2 directories
Thanks in advance.
Regards,
Moin

Forum Home > Enterprise JavaBeans[tm]
Topic: Help required in Weblogic 6 - Creation & Configuration of Web Application
Duke Dollars
2 Duke Dollars assigned to this topic. Reward the best responses to your question
using the icons below, or transfer additional Duke Dollars to this topic.
Welcome moinshariff!
Watching this topic.
Previous Topic Next Topic
This topic has 1 reply on 1 page (Most recent message: Jan 23, 2002 1:05 AM)
Author: moinshariff Jan 22, 2002 4:55 AM
Hi,
I am using Weblogic 6. I have created a new Web
Application called Web (I have not used the DefaultWebApp_myserver).
And I have the following settings:
Name : Web
URI : Web
and Path : C:\Web
and placed my JSP files under c:\Web\
I am able to access the first page, but after that I am not able to access the
second page.
I get "Error 404--Not Found" on the browser. Basically the class file is not getting
created under /Web-inf/_tmp_war_myserver_myserver_Web/jsp_servlet/ folder .
I tried a work around for this. I copied all my files under one more folder called
web and placed this under C:\Web
The it works. Now I have 2 copied off all the files, 1 copy under c:\web and another
copy under c:\web\web\.
If I have the files under DefaultWebApp_myserver and have the setting as
Name: DefaultWebApp_myserver
URI: DefaultWebApp_myserver
Path: .\config\mydomain\applications
everything works fine.
Can any one please let me know if there is any configuration which has to be done
so that I do not duplicate the code in 2 directories
Thanks in advance.
Regards,
Moin

Help required network configuration - Gateway route settings get erased on reboot.

Oracle Linux 7
Linux myhostname 3.8.13-35.3.1.el7uek.x86_64 #2 SMP Wed Jun 25 15:27:43 PDT 2014 x86_64 x86_64 x86_64 GNU/Linux
#cat /etc/sysconfig/network-scripts/ifcfg-eno16780032
TYPE="Ethernet"
BOOTPROTO="none"
DEFROUTE="yes"
IPV4_FAILURE_FATAL="no"
IPV6INIT="yes"
IPV6_AUTOCONF="yes"
IPV6_DEFROUTE="yes"
IPV6_FAILURE_FATAL="no"
NAME="eno16780032"
UUID="2d1107e3-8bd9-49b1-b726-701c56dc368b"
ONBOOT="yes"
IPADDR0="34.36.140.86"
PREFIX0="22"
GATEWAY0="34.36.143.254"
DNS1="34.36.132.1"
DNS2="34.34.132.1"
DOMAIN="corp.halliburton.com"
HWADDR="00:50:56:AC:3F:F9"
IPV6_PEERDNS="yes"
IPV6_PEERROUTES="yes"
NM_CONTROLLED="no"
#route -n
Kernel IP routing table
Destination     Gateway         Genmask         Flags Metric Ref    Use Iface
0.0.0.0         34.36.143.254   0.0.0.0         UG    0      0        0 eno16780032
34.36.140.0     0.0.0.0         255.255.252.0   U     0      0        0 eno16780032
169.254.0.0     0.0.0.0         255.255.0.0     U     1002   0        0 eno16780032
When I reboot the machine, the first line in route table gets erased, I then run:
#route add default gw 34.36.143.254
After which network works fine.
Help required. I don't want to use NetworkManager.

The following might be useful:
https://access.redhat.com/solutions/783533
"When transitioning from NetworkManager to using the network initscript, the default gateway parameter in the interface's ifcfg file will be depicted as 'GATEWAY0'. In order for the ifcfg file to be compatible with the network initscript, this parameter must be renamed to 'GATEWAY'. This limitation will be addressed in an upcoming release of RHEL7."
NetworkManager is now the default mechanism for RHEL 7. Personally I don't quite understand this, because as far as I can gather it is a program for systems to automatically detect and connect to known networks. I think such functionality can be useful when switching between wireless and wired networks, but for a server platform, I wonder.

Help Required - Oracle AS 10g

hello,
i have just downloaded oracle 10g softwares ...
i installed database then developer suite ... everything was fine ... until i was unable to run forms ...
a friend of mine told me that i need to install application server in order to run forms ...
1st of all i want to know that is there any way i can run forms without using Oracle AS 10g ...
2ndly i m facing problems in installation of Oracle AS 10g ...
i have studied online documentation but it ain't so helpfull for me ...
it seems like ... i have to install "Oracle AS infrastructure" first and then "Middle-tier: Business Intelligence and forms" ...
i m using P-IV (AMD Athlon XP 2100+, MMX, 1.7GHz Processor) with 512 MB DD RAM and Windows XP Professional with Service Pack 2 as Operating System.
During installation, the installer is warning dat only "Oracle Application Server (J2EE and Web Cache)" and "Oracle Application Server Developer Kits" are supported installations on dis platform ...
what should i do ... urgent help required ...
regards,
yasir ([email protected])

@ brusardl and rkogelhe
thanx for replying ...
brusardl
i didn't changed da port while installing Oracle AS ...
inspite i stopped all services using/listening from dat port ...
now ... i guess there has been some conflict ... as database listner stops automatically just after starting !!!
rkogelhe
can u plz tell me what is BI version of Forms ...
and can i view forms running on web without installing Oracle AS with OC4J bundled in Forms ???
Another Problem:
I re-installed Database, Developer suite and then Oracle AS infrastructure ...
everthing went fine ...
when i installed Oracle AS Middle Tier - Business Intelligence & Forms
during installation ... some configuration assistants failed/skipped ...
da OC4J configration assistant at 5th last position failed ... so remaining 4 configuration assistants were skipped ...
at da end it said ... Installation Succesfull but with some configuration assistants failed/skipped ...
is dis a installation useless ... can i fix dis ?
regards,
yasir

Help required in module insertion

Similar Messages

Maybe you are looking for