Help to connect 2 switches together

Hi
I need your help to can i make 2 switches 2950 and 2960 connecting it together through trunk port,so in my question is what the command that should be on the trunk port???
I wrote the below command but it's not acceptable:
Switch(condig-if)#switchport trunk encapsolation isl

abakrbshat wrote:Hi,thanks for your responseI did that right now but still the pc unable on the ping to other pc in other switch
Do the interfaces on the switches come up when connected? What do you get when you input "show interface X/Y" on each switch?
Are the source and destination PC in the same VLAN (1 by default, something else if it's been changed), and have IP addresses in the same subnet?
And, lastly - are they Windows boxes? If so, do you have the firewall turned OFF? Recent Windows boxes seem to block PING by default unless you tell them otherwise.

Similar Messages

Connecting switches together

hi,
What is the best way to connect switch together (with 2960 switch)..cross or stright cable...up/down or normal port ?
WAN ----Router 1 --- -SW1 ---- SW2
                                  |
                                  |
                                 SW3----SW4----SW5 (no vlan)---PC1
all switch has up,down and normal port except SW5
Does SW5 will support vlan if it is connect to a layer 2 switch (let s say sw5 is connected to port 5 of SW4 (and port 5 is VLAN 20 access mode...then trunk between SW3 and SW1))...is there any inheritance ?
Hope, this time, this post will be post on the forum.
Thanks for help,

Hi Loic the wire between switch 4 and 5 shouldn't make a difference in terms of rj45 so long as it is auto set (which by default it is). If you want switch 5 to be vlan 20, configure vlan 20 there and the port on switch 4 must also have vlan 20. So long as either switch is tag or untag, but both configuration matching it will work fine.
-Tom
Please mark answered for helpful posts

Linking two switches together.

hi Guys ,
quick question in relation to joining two switches together,
can I link a 2950 switch with a 1000 BASE-SX with a 3560G with 4 SPF ports with fibre and what pitfalls should i look out for .
Thanks in advance
Kevin

Hello,
So you would like to connect GBIC to SFP, you need Multimode Duplex Fiber Optical cable with SC-LC connectors. If SFP to SFP you need the same cably type with LC-LC connectors.
http://www.cisco.com/en/US/products/hw/routers/ps341/prod_module_installation_guide09186a00801cc731.html
http://cisco.com/en/US/products/hw/modules/ps5455/products_data_sheet09186a008014cb5e.html
bye
FCS
Please rate me if I helped.

Wireless Radio Connection - switches off

My Wireless Radio Connection switches off after about 2-3 minutes. Is there a setting I can adjust to lengthen this amount of time? When it shuts off, all I have to do is FN5 to reconnect but I shouldn't have to do that every 3 minutes. I have a T60. Thank you.

Assuming your're using a version of Windows, use the Device Manager and configure the Advanced Properties
DISABLE /UNCHECK "ALLOW WINDOWS TO TURN OFF DEVICE TO CONSERVE POWER"
Next, ensure all the PowerManager settings are set to a a Max Performance / Vid Presentation Profile but this doesn't necessarily ensure the WiFi NIC could be turned off if you or someone else has tuned the power profiles to disable NIC's after whatever period of time
It doesn't hurt to verify within the BIOS PCI PowerMgmt IS ENABLED and the Smart CPU settings are activated.
If the issue is still occurring then load an alnternate Operating system, Knoppix or SLAX Live BOOT CD's enable the loading and execution of a featured LINUX kernel with driver support for most Thinkpads since it seems te developers of the LIVE CD's use thinkpads themselves or MAC's, it is likely the latest Knoppix distro is compatible with your NIC and observe whether or not the issue still occurs / if so then you can most likely attribute it to an odd hardware issue and you should begin researching whether or not a BIOS upgrade or even Downgrade is a solution.
Before flashing, it is worth taking note of the fact the intermittent power issues seem to be related to your Windows build and you should install a parallel installation of any compatible Windows version then install the barebones necessary drivers to determine if the power issues still occur on a freshly minted version of Windows.
Also, determine whether or not your actual WiFi NIC is flashable, modern network adapaters have increased in complexity especially as a necessity of WOL and the Intel SLM features that more corporate purchasers demand thus NIC's have increased in complexity becoming more like mini VX systems with flashable firmware which may have merit as a solution if you isolate it to your hardware.
Don't just sit there, take a second and use the Kudo's button to compliment the people who help you.

Can anyone help me connect my Macbook Air to a SAMSUNG TV. When I follow the basic instructions (Thunderbolt to HDMI connection) the screen on my computer goes grey and an error message appears inviting me to press any button to restart th

Can anyone help me connect my Macbook Air to a SAMSUNG TV. When I follow the basic instructions (Thunderbolt to HDMI connection) the screen on my computer goes grey and an error message appears inviting me to press any button to restart the Macbook. When I do this nothing happens. Only when I disconnect the computer from the TV does the Macbook allow me to login. The TV does not receive any signal from the Macbook even though I know the HDI port works fine. Any ideas what I'm doing wrong? Do I need to enable something on the Macbook?

An update...
I downloaded Apple's (rather large!) list of software updates today, and I was finally able to recognize my iPod again. I did a restore using the iPod updater from 06-2006, and all seemed to work OK. (I'm afraid to try the new one again!)
Then I tried to re-load my music library from iTunes, and got stuck. It froze up after a while and wouldn't go any further.
When I disconnected my iPod from my computer, I find 2 podcasts and nothing else, though iTunes told me it had transferred 600+ songs. Those 2 podcasts do play fine, and the basic iPod software all seems to be intact.
So -- anyone get through this connection problem and have any ideas to share??
iMac Mac OS X (10.4.7)

Help need to switch Muse site to BC on a allready hosted plan

Hi, i also posted on BC forum...
I have a client that was in a hurry to have his emails accounts before the entire website.
So i went on and bought the email marketing plan (cos he will also need to do email campains) an pointed his domain everything is working fine, at this moment he has his accounts the domain is live.
The site would be just a small 7-10 pages not to complicated.
Has a graphic designer (who has venture into Business catalyst cos it had all the solutions i needed, well that's what the promotional videos said anyway) I made a site in Muse.
First i did a temporary page thats says "comming soon", and then i made the entire site, all the design and menu but with blank pages cos the client didnt have all the content yet (and still dont have). I uploaded that site to a sub directory so he could see the evolution.
He approved the design, yay!
At the end of the process, he told me he needed to have full control with the editor. (style, images, bulleted list, need to put downloadable document like pdf etc.) i told him that he could only modify what was allready there with the Muse in Browser editing (that he saw when i made the pitch using another site) he was impress with the way it worked.
so i told him i would have to remake "template".
I thought of using a BC template, and modify the looks to adapt to my client image, Of course, use a responsive theme so he could make the change at one place only. (cos in Muse you need to make the changes on the 3 layouts).
Now, i created a new temporary site using one of the new responsive template available.
How can i import that new site onto his live domain? In other words, how can a switch from a theme made in Muse, to a BC template?
cant i just delete everything in the root folder, and upload the entire new site via ftp?
please help me find the solution. i am a bit in a panic here
hope you could understand my lousy English.
Sincerely,
i.d.

This would need to be transparent for m'y client...
Y
Envoyé de mon iPhone
Le 2014-04-20 à 15:29, Sanjit_Das <[email protected]> a écrit :
Re: help need to switch Muse site to BC on a allready hosted plan
created by Sanjit_Das in Help with using Adobe Muse CC - View the full discussion
Thanks for additional details.
Unfortunately we cannot change site template of a live site in BC , but as a workaround Create a site from BC using the template you wish to use then publish the site from Muse to the site created from BC and transfer the contents stored from live site to trial site. Ater final transition is done , you can delete the already paid site and make live the new trial site which includes new site template.
Thanks,
Sanjit
Please note that the Adobe Forums do not accept email attachments. If you want to embed a screen image in your message please visit the thread in the forum to embed the image at http://forums.adobe.com/message/6314730#6314730
Replies to this message go to everyone subscribed to this thread, not directly to the person who posted the message. To post a reply, either reply to this email or visit the message page: http://forums.adobe.com/message/6314730#6314730
To unsubscribe from this thread, please visit the message page at http://forums.adobe.com/message/6314730#6314730. In the Actions box on the right, click the Stop Email Notifications link.
Start a new discussion in Help with using Adobe Muse CC at Adobe Community
For more information about maintaining your forum email notifications please go to http://forums.adobe.com/thread/416458?tstart=0.

Help with connection flash builder 4.5 to remote php database

help with connection flash builder 4.5 to remote php database

Fatal error: require_once() [function.require]: Failed opening required 'Zend/Loader/Autoloader.php' (include_path='.;C:\php5\pear;D:/webserver/apache2/htdocs/ZendFramework/library') in D:\webserver\apache2\htdocs\giga\first-debug\gateway.php on line 27

Help me connect my application

hello,
I try to connect to my database from an application. do somebody have a sample settings file to give to me? what I mean is: how can i fell the following statement:
string
' designate the following (in this order):
' DB Index, DB Name, DB Type, DB Filepath, Server Name, Username, Password
I think that my "DB Type,DB Filepath,server name" are wrong so could you give me your DB Type,DB Type,Server Name as an example?
thanks

Wow! A quintuple posting. Are you going for a record?
settings file
help me connect my application
help me connect my application
help me connect my application
help me connect my application
This may actually constitute spam.

How to connect switch controls to float PLC items ?

The AB PLC float items are 32 bits, but the LV boolean variables are 8 bits!
So how can I connect switch controls to these float items???
Thanks in advance

Check this
http://forums.lavag.org/Industrial-EtherNet-EtherNet-IP-t9041.html
Best regards
Siva
[email protected]

Help with connecting Nintendo dsi to internet

I really need some help with connecting my daughters nintendo dsi to the internet, I have tried everything but just can't get it to work. Would really appreciate any advice....

Hi sandy and welcome
Have a read http://bt.custhelp.com/app/answers/detail/a_id/11263/c/346%2C502%2C504/kw/nintendo%20ds/r_id/125731
Note: The Nintendo DS only supports either no security or WEP security!!
-+-No longer a forum member-+-

Please help, i connect my phone to computer and gives me error code this i phone cannot be used because the apple mobile device is not started

please help, i connect my phone to computer and gives me error code this i phone cannot be used because the apple mobile device is not started

http://support.apple.com/kb/HT1923
uninstall and reinstall
there is a complicated way to work with just the mobile device support but its simpler just to uninstall itunes and related components and then reinstall itunes
ur music will be fine, u will just lose the playlists. but ur mobile device support will be working again.

My Ipad2 just shuts down and will not turn on. Rebooting does not help. He switched on when I start charging it. In this case, the battery is charged.

My Ipad2 just shuts down and will not turn on. Rebooting does not help. He switched on when I start charging it. In this case, the battery is charged.

Standard troubleshooting steps in the following order:
1. Reset: Press the sleep/wake button & home button at the same time, keep pressing until you see the apple logo, then release. Ignore the slide to power off.
If no change, continue:
2. Restore your phone from a backup, note: if the problem is related to corrupt data, while this will restore a fresh OS, it will also restore the problem.
If no change, continue:
3. Restore as a "new" phone in itunes & re-sync your content. All saved data will be lost.
If no change, make an appointment at an Apple store.

Help to connect Microoft Remote Dextop (win7) with Iphone 5 using RD client

Help to connect Microoft Remote Dextop (win7) with Iphone 5 using RD client Hello, I can connect my iphone 5 to my laptop(windows7 OS) with RD client while My iphone is also connected with my laptop's wifi hotspot. And i can remotely control my laptop with the iphone nicely while I am in the laptop's wifi range. Is it possible to control my laptop from iphone while my phone is not connected to laptop's wifi hotspot???? I use 3G internet in my phone while I go out of home.

I have no issue using cellular data when I remote in from my iphone with the RD client.
Have you tried using cellular data to remote in?

TS1398 I need help getting connected to our home wifi.

I need help getting connected to our home wifi. I've reset network settings, iPhone, and router but the error "unable to join network" keeps coming up. I also double checked the password. Please help

Other possibilities:
Your router firmware is out of date. Check the manufacturer's website for an update
You have MAC (Media Access Control) filtering enabled on the router, that restricts access to "known" devices and the new iPhone is not on the table of known devices
Your router has a setting limiting the number of simultaneous allowed devices
Your routers SSID ("name") is still the default (e.g., LINKSYS, DLINK, NETGEAR, etc). Your phone has encountered other routers with the same name as you have traveled, and the phone is confused as to which router is the real one. If your router's name is still the default you should change it.

Need help to connect to aws instance from my macbook pro

i need help to connect to an aws instance from my laptop. Please help me..

No, it's not Apple's doing.
You are infected with Downlite, which is preventing you from accessing the AdwareMedic site. For an explanation and some solutions, see:
http://www.thesafemac.com/adware-blocking-adwaremedic-downloads/
If the adware prevents you from loading that page as well, try this one:
https://discussions.apple.com/docs/DOC-7792
(Fair disclosure: I may receive compensation from links to my sites, TheSafeMac.com and AdwareMedic.com, in the form of buttons allowing for donations. Donations are not required to use my site or software.)

Help to connect 2 switches together

Similar Messages

Maybe you are looking for