HELP! Variation on Standby issue

OK, so last week I closed the lid on my Thinkpad T400 running XP
After I opened the lid the screen just stayed black.
I had previously set the power manager so that closing the lid did nothing. In other words, my setting was that closing the lid was NOT supposed to standby the laptop.
Restarting did not help at all. After entering my PW at the cntl-alt-del screen, it would briefly show the wallpaper and then the screen would go black. Still does this. Seems like it is going into standby but not sure.
Finally hit on a workaround that works 40% of the time:
Start computer, at the cntl-alt-del screen put system into standby, let it sit, wake it up with power button, log on normally. Only works sometimes.
If I am at work and put it into the docking station it works fine; that is, my 2 external monitors work just fine, no need to monkey with anything..
To try and fix this I have:
- Updated BIOS
- Reinstalled Thinkpad power manager (and made sure I set it to NEVER go into standby)
- Reinstalled video driver
Nothing works, about ready to drop kick this laptop out the window.

Hi and Welcome to the Forums!
Wow...hard to decipher what you said there, but from what I can guess about it, it sounds like you have a BB on a corporate/enterprise BES system, and your system admin has restricted your ability to install 3rd party apps. There is no way around that...you must go see the BES admins and find out if they can relax that restriction.
Good luck!
Occam's Razor nearly always applies when troubleshooting technology issues!
If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
Join our BBM Channels
BSCF General Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

Similar Messages

I am not able to launch FF everytime i tr to open it, it says FF has to submit a crash report, i even tried doing that and the report was submitted too, but stiil FF did not start, and the problem still persists, please help me solve this issue in English

Question
I am not able to launch FF everytime i try to open it, it says FF has to submit a crash report,and restore yr tabs. I even tried doing that and the report was submitted too, but still FF did not start, and the problem still persists, please help me solve this issue
'''(in English)'''

Hi Danny,
Per my understanding that you can't get the expect result by using the expression "=Count(Fields!TICKET_STATUS.Value=4) " to count the the TICKET_STATUS which value is 4, the result will returns the count of all the TICKET_STATUS values(206)
but not 180, right?
I have tested on my local environment and can reproduce the issue, the issue caused by you are using the count() function in the incorrect way, please modify the expression as below and have a test:
=COUNT(IIF(Fields!TICKET_STATUS.Value=4 ,1,Nothing))
or
=SUM(IIF(Fields!TICKET_STATUS=4,1,0))
If you still have any problem, please feel free to ask.
Regards,
Vicky Liu
Vicky Liu
TechNet Community Support

Urgent help needed; Database shutdown issues.

Urgent help needed; Database shutdown issues.
Hi all,
I am trying to shutdown my SAP database and am facing the issues below, can someone please suggest how I can go about resolving this issue and restart the database?
SQL> shutdown immediate
ORA-24324: service handle not initialized
ORA-24323: value not allowed
ORA-01089: immediate shutdown in progress - no operations are permitted
SQL> shutdown abort
ORA-01031: insufficient privileges
Thanks and regards,
Iqbal

Hi,
check SAP Note 700548 - FAQ: Oracle authorizations
also check Note 834917 - Oracle Database 10g: New database role SAPCONN
regards,
kaushal

Hi, Firefox keeps crashing, the crash signature is ProcessBoundaryCells. I tried searching Mozilla, but there are no supporting articles. If anyone can please help me fix this issue, that would be great. Thanks

Hi, Firefox on my desktop keeps crashing at just random moments. Sometimes not very often at all, but other times it can happen a few times within an hour.
My Desktop Window Manager also crashes regularly and the dialogue box always pops up saying its stopped working. However, this doesn't seem to effect anything.
It could be realated though, as I just had this desktop built a few weeks ago and a few times it's crashed as well as programs.
If anyone can help me fix this issue with Firefox, that would be great. Thanks in advance.

Hi,
I updated the Flash plugin, but I still keep getting crashes.
I will try to disable the hardware acceleration in the Flash Player as you recommended and hopefully this will work.
Although the last crash report I got has a different problem then before,
https://crash-stats.mozilla.com/report/index/6c5d8c66-6789-4b52-94e4-61cdf2110530
Signature: BuildArgArray
If you can please offer any more advice that would be great, thanks.

I have updated my Macbook Pro from 10.7.5 to 10.9.1 and it keeps on restarting after upgrade. Please help me fix this issue.

Hi All,
I have updated the Macbook Pro from 10.7.5 to 10.9.1 today and once it is done I restarted the system and it keeps on crashing/restarting the system every 2 min.
I have found the below backtrace. Please help me fix this issue.
Anonymous UUID:
C72C8841-51A0-BB21-689C-2AB204820087
Mon Dec 30 23:57:23 2013
panic(cpu 0 caller 0xffffff801da5260f): "a freed zone element has been modified: expected 0xdeadbeefdeadbeef but found 0, bits changed 0xdeadbeefdeadbeef, at offset 8 of 128 in zone: kalloc.128"@/SourceCache/xnu/xnu-2422.1.72/osfmk/kern/zalloc.c:461
Backtrace (CPU 0), Frame : Return Address
0xffffff8096bf3690 : 0xffffff801da22f69
0xffffff8096bf3710 : 0xffffff801da5260f
0xffffff8096bf3770 : 0xffffff801da51d09
0xffffff8096bf3870 : 0xffffff801da2aa2f
0xffffff8096bf38a0 : 0xffffff801dde080d
0xffffff8096bf38e0 : 0xffffff7f9fcada11
0xffffff8096bf3930 : 0xffffff7f9fcae16e
0xffffff8096bf39a0 : 0xffffff7f9fcae523
0xffffff8096bf39d0 : 0xffffff801dc13438
0xffffff8096bf3a00 : 0xffffff801dd83378
0xffffff8096bf3a70 : 0xffffff801dbfd1ae
0xffffff8096bf3ae0 : 0xffffff801dbf437a
0xffffff8096bf3b80 : 0xffffff801dbe5f15
0xffffff8096bf3c30 : 0xffffff801dbe67d2
0xffffff8096bf3f50 : 0xffffff801de3de23
0xffffff8096bf3fb0 : 0xffffff801daf3e06
Kernel Extensions in backtrace:
com.apple.AppleFSCompression.AppleFSCompressionTypeZlib(1.0d1)[E163B7AE-F6E5-328 6-B827-66DB3FE3DB7B]@0xffffff7f9fcac000->0xffffff7f9fcaffff
BSD process name corresponding to current thread: applet
Mac OS version:
13B42
Kernel version:
Darwin Kernel Version 13.0.0: Thu Sep 19 22:22:27 PDT 2013; root:xnu-2422.1.72~6/RELEASE_X86_64
Kernel UUID: 1D9369E3-D0A5-31B6-8D16-BFFBBB390393
Kernel slide:
0x000000001d800000
Kernel text base: 0xffffff801da00000
System model name: MacBookPro7,1 (Mac-F222BEC8)
System uptime in nanoseconds: 172506613860
last loaded kext at 107245362778: com.trendmicro.kext.KERedirect 1.0.0 (addr 0xffffff7f9ff33000, size 24576)
loaded kexts:
com.trendmicro.kext.KERedirect 1.0.0
com.logmein.driver.LogMeInSoundDriver 1.0.0
org.virtualbox.kext.VBoxUSB 3.2.6
org.virtualbox.kext.VBoxDrv 3.2.6
com.apple.driver.AppleHWSensor 1.9.5d0
com.apple.driver.AppleHDAHardwareConfigDriver 2.5.3fc1
com.apple.driver.AudioAUUC 1.60
com.apple.driver.AGPM 100.14.11
com.apple.driver.AppleTyMCEDriver 1.0.2d2
com.apple.driver.AppleMikeyHIDDriver 124
com.apple.driver.AppleHDA 2.5.3fc1
com.apple.iokit.IOBluetoothSerialManager 4.2.0f6
com.apple.filesystems.autofs 3.0
com.apple.GeForceTesla 8.1.8
com.apple.driver.AppleSMCLMU 2.0.4d1
com.apple.iokit.IOUserEthernet 1.0.0d1
com.apple.Dont_Steal_Mac_OS_X 7.0.0
com.apple.driver.AppleHWAccess 1
com.apple.driver.AppleMikeyDriver 2.5.3fc1
com.apple.driver.ACPI_SMC_PlatformPlugin 1.0.0
com.apple.driver.AppleMuxControl 3.4.12
com.apple.driver.AppleBacklight 170.3.5
com.apple.driver.AppleLPC 1.7.0
com.apple.driver.AppleUpstreamUserClient 3.5.13
com.apple.nvidia.NVDAStartup 8.1.8
com.apple.driver.SMCMotionSensor 3.0.4d1
com.apple.iokit.IOBluetoothUSBDFU 4.2.0f6
com.apple.iokit.BroadcomBluetoothHostControllerUSBTransport 4.2.0f6
com.apple.driver.AppleMCCSControl 1.1.12
com.apple.driver.AppleUSBTCButtons 240.2
com.apple.driver.AppleIRController 325.7
com.apple.driver.AppleUSBTCKeyEventDriver 240.2
com.apple.driver.AppleUSBTCKeyboard 240.2
com.apple.driver.AppleUSBCardReader 3.3.5
com.apple.driver.AppleFileSystemDriver 3.0.1
com.apple.AppleFSCompression.AppleFSCompressionTypeDataless 1.0.0d1
com.apple.AppleFSCompression.AppleFSCompressionTypeZlib 1.0.0d1
com.apple.BootCache 35
com.apple.iokit.SCSITaskUserClient 3.6.0
com.apple.driver.XsanFilter 404
com.apple.iokit.IOAHCIBlockStorage 2.4.0
com.apple.iokit.AppleBCM5701Ethernet 3.6.9b9
com.apple.driver.AirPort.Brcm4331 700.20.22
com.apple.driver.AppleAHCIPort 2.9.5
com.apple.driver.AppleFWOHCI 4.9.9
com.apple.driver.AppleUSBHub 650.4.4
com.apple.driver.AppleUSBEHCI 650.4.1
com.apple.driver.AppleUSBOHCI 650.4.1
com.apple.driver.AppleSmartBatteryManager 161.0.0
com.apple.driver.AppleRTC 2.0
com.apple.driver.AppleHPET 1.8
com.apple.driver.AppleACPIButtons 2.0
com.apple.driver.AppleSMBIOS 2.0
com.apple.driver.AppleACPIEC 2.0
com.apple.driver.AppleAPIC 1.7
com.apple.driver.AppleIntelCPUPowerManagementClient 216.0.0
com.apple.nke.applicationfirewall 153
com.apple.security.quarantine 3
com.apple.driver.AppleIntelCPUPowerManagement 216.0.0
com.apple.AppleGraphicsDeviceControl 3.4.12
com.apple.driver.DspFuncLib 2.5.3fc1
com.apple.vecLib.kext 1.0.0
com.apple.iokit.IOSerialFamily 10.0.7
com.apple.kext.triggers 1.0
com.apple.nvidia.classic.NVDANV50HalTesla 8.1.8
com.apple.iokit.IOAudioFamily 1.9.4fc11
com.apple.kext.OSvKernDSPLib 1.14
com.apple.iokit.IOSurface 91
com.apple.iokit.IOBluetoothFamily 4.2.0f6
com.apple.driver.IOPlatformPluginLegacy 1.0.0
com.apple.driver.AppleGraphicsControl 3.4.12
com.apple.driver.AppleBacklightExpert 1.0.4
com.apple.driver.IOPlatformPluginFamily 5.5.1d27
com.apple.nvidia.classic.NVDAResmanTesla 8.1.8
com.apple.iokit.IONDRVSupport 2.3.6
com.apple.driver.AppleSMC 3.1.6d1
com.apple.iokit.IOBluetoothHostControllerUSBTransport 4.2.0f6
com.apple.iokit.IOFireWireIP 2.2.5
com.apple.driver.AppleHDAController 2.5.3fc1
com.apple.iokit.IOHDAFamily 2.5.3fc1
com.apple.driver.AppleSMBusPCI 1.0.12d1
com.apple.driver.AppleSMBusController 1.0.11d1
com.apple.iokit.IOGraphicsFamily 2.3.6
com.apple.driver.AppleUSBMultitouch 240.6
com.apple.iokit.IOUSBHIDDriver 650.4.4
com.apple.iokit.IOSCSIBlockCommandsDevice 3.6.0
com.apple.iokit.IOUSBMassStorageClass 3.6.0
com.apple.driver.AppleUSBMergeNub 650.4.0
com.apple.driver.AppleUSBComposite 650.4.0
com.apple.iokit.IOSCSIMultimediaCommandsDevice 3.6.0
com.apple.iokit.IOBDStorageFamily 1.7
com.apple.iokit.IODVDStorageFamily 1.7.1
com.apple.iokit.IOCDStorageFamily 1.7.1
com.apple.iokit.IOAHCISerialATAPI 2.6.0
com.apple.iokit.IOSCSIArchitectureModelFamily 3.6.0
com.apple.iokit.IOEthernetAVBController 1.0.3b3
com.apple.driver.mDNSOffloadUserClient 1.0.1b4
com.apple.iokit.IO80211Family 600.34
com.apple.iokit.IONetworkingFamily 3.2
com.apple.iokit.IOAHCIFamily 2.6.0
com.apple.iokit.IOFireWireFamily 4.5.5
com.apple.driver.AppleMCP89RootPortPM 1.11
com.apple.iokit.IOUSBUserClient 650.4.4
com.apple.driver.AppleEFINVRAM 2.0
com.apple.driver.AppleEFIRuntime 2.0
com.apple.iokit.IOUSBFamily 650.4.4
com.apple.driver.NVSMU 2.2.9
com.apple.iokit.IOHIDFamily 2.0.0
com.apple.iokit.IOSMBusFamily 1.1
com.apple.security.sandbox 278.10
com.apple.kext.AppleMatch 1.0.0d1
com.apple.security.TMSafetyNet 7
com.apple.driver.AppleKeyStore 2
com.apple.driver.DiskImages 371.1
com.apple.iokit.IOStorageFamily 1.9
com.apple.iokit.IOReportFamily 21
com.apple.driver.AppleFDEKeyStore 28.30
com.apple.driver.AppleACPIPlatform 2.0
com.apple.iokit.IOPCIFamily 2.8
com.apple.iokit.IOACPIFamily 1.4
com.apple.kec.corecrypto 1.0
com.apple.kec.pthread 1
Unable to gather system configuration information.Model: MacBookPro7,1, BootROM MBP71.0039.B0E, 2 processors, Intel Core 2 Duo, 2.4 GHz, 4 GB, SMC 1.62f7
Graphics: NVIDIA GeForce 320M, NVIDIA GeForce 320M, PCI, 256 MB
Memory Module: BANK 0/DIMM0, 2 GB, DDR3, 1067 MHz, 0x80CE, 0x4D34373142353637334648302D4346382020
Memory Module: BANK 1/DIMM0, 2 GB, DDR3, 1067 MHz, 0x80CE, 0x4D34373142353637334648302D4346382020
AirPort: spairport_wireless_card_type_airport_extreme (0x14E4, 0x8D), Broadcom BCM43xx 1.0 (5.106.98.100.22)
Bluetooth: Version 4.2.0f6 12982, 3 services, 15 devices, 0 incoming serial ports
Network Service: Wi-Fi, AirPort, en1
Serial ATA Device: TOSHIBA MK2555GSXF, 250.06 GB
Serial ATA Device: HL-DT-ST DVDRW GS23N
USB Device: Built-in iSight
USB Device: Internal Memory Card Reader
USB Device: BRCM2046 Hub
USB Device: Bluetooth USB Host Controller
USB Device: IR Receiver
USB Device: Apple Internal Keyboard / Trackpad
Thunderbolt Bus:
Please help me fix this issue.
Thank you,
Nishanth

Please read this whole message before doing anything.
This procedure is a diagnostic test. It’s unlikely to solve your problem. Don’t be disappointed when you find that nothing has changed after you complete it.
The purpose of the test is to determine whether the problem is caused by third-party software that loads automatically at startup or login, by a peripheral device, by a font conflict, or by corruption of the file system or of certain system caches.
Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards, if applicable. Start up in safe mode and log in to the account with the problem. You must hold down the shift key twice: once when you boot, and again when you log in.
Note: If FileVault is enabled, or if a firmware password is set, or if the boot volume is a software RAID, you can’t do this. Ask for further instructions.
Safe mode is much slower to boot and run than normal, with limited graphics performance, and some things won’t work at all, including sound output and Wi-Fi on certain models. The next normal boot may also be somewhat slow.
The login screen appears even if you usually login automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
Test while in safe mode. Same problem?
After testing, reboot as usual (i.e., not in safe mode) and verify that you still have the problem. Post the results of the test.

HT201210 (The iPhone "Named" cannot be restored at this time because the iPhone software update server could not be contacted or is temporarily unavailable.) can anyone help me with this issue, every time i try to restore it will come up like this error m

(The iPhone "Named" cannot be restored at this time because the iPhone software update server could not be contacted or is temporarily unavailable.)
can anyone help me with this issue, every time i try to restore it will come up like this error message.

Restore the iPhone when connected to iTunes by cable.
Still the same TS1275?
Is your iPhone jailbroken?
Or
Has your computer ever been used to jailbrake or downgrade (Tinyumbrella) any iPhone?

I purchased my iPhone from UK which is unlocked but Now I am back to My Origin i.e INDIA and unfortunately my iPhone Display get damaged and Now I have to Repair it but..... The Problem is "iSTORE in India Doesn't Helping me in this issue"

I purchased my iPhone from UK which is unlocked.
But Now I am back to My Origin Place i.e INDIA.
And unfortunately my iPhone Display get damaged.. and Now I have to Repair it but.....
The Problem is "iSTORE in India Doesn't Helping me in this issue".
I would request APPLE please get this FIX as I am also your customer and now it is globalization.
SO please find any way to get this fixed...
Apple Customer care Please send me any Services note That I can show to iStore in India i.e (In Korum mall Thane, Mumbai, Maharashtra, India )
So I can get my dispaly fixed in INDIA itself.
Requested to please help me out of this issue..
Thanks
APPLE user
sonu.mas007

They can provide some kind of way towards this solutions...
eg:
1) Accept my UK iPhone in India courier it to Purchased Place (Repaired it)
2) Accept my UK iPhone in India Take some difference assign me India iPhone.
3) Accept my UK iPhone in India give me any option to ugreade to iPhone 5 (Indian).
4) Accept my UK iPhone in India give me some Receipt (Courier me My new iPhone from UK).
5) Approve my VISA for going to UK again as it not easy for INDIAN to go there with some kind of this Reason.
6) Give the Postal Address where we can send our APPLE to get only Service and they can send it back to us if it got reparied.
As no one would like to go UK only to Purchase APPLE..
There are some personal reason they have to go to Other countries for ... and If some one is FAN of APPLE like me would do the same mistake that I have done..
7) If the APPLE wanted to serve their customer they would have get to the solutions with their excellent mind.
As far as I am concern I am just the USER of my FAV APPLE but.. .. I guess this policy would not keep me as the SAME FAN of APPLE as I am now...
If this is not going to get solved I guess I have to start with other BRAND Like SAMSUNG S4 where I can get everything in my STATE..
But YEH it not a right was to have this BAD policy.
I just dont know why they are not coming ip with great solution for this issue in this tecnology world.
Any help to find other BEST Brand who has awesome services..

Please help me in this issue "rebate \management"

Dear all,
I have a problem, please kindly help me on my issue.
For the rebate process, my client requires for their customers once the time period is over he dont want to raise the credit memo reuqest on the behalf of credit memo client want to replace the goods at free of cost to their customers.
Kindly help me in this issue
rama murthy.g

img-s&D - billing- rebates-rebateagreement type .in the rebate agreement control settings ,in the final settlement field ,u put free of goods sales document type
if useful give me rewards
thanks
raj

Calendar and Time showing in arabic but my phone's language is English. I bought my phone from DU in UAE , Dubai. Please help me solve this issue while keeping the Region to United Arab Emirates

Calendar and Time showing in arabic but my phone's language is English. I bought my phone from DU in UAE , Dubai. Please help me solve this issue while keeping the Region to United Arab Emirates

Valentine350z wrote:
while keeping the Region to United Arab Emirates
Not possible, I think. Tell Apple how you feel about this at
http://www.apple.com/feedback/iphone.html

TS3074 im can u please help me out this issue im trying to install iTunes in windows 7 some error showing " windows installer package problem DLL require to complete this installation" this message showing.

im can u please help me out this issue im trying to install iTunes in windows 7 some error showing " windows installer package problem DLL require to complete this installation" this message showing.

Try the following user tip:
" ... A DLL required for this installation to complete could not be run ..." error messages when installing iTunes for Windows

Will Apple help me with this issue?

Dear Sir or Madam，
I am a student in China, I really need your help, my iphone now problems bothers me! HELP ME PLEASE!!!
As I bought my iPhone 4s(16GB,White) in the USA from Sprint, full price with tax, unlocked ,it was excepted to be a global phone. But now I come across with some problems in China using local carrier.Now I am in China, not the normal use of the phone, I rely on odd jobs to earn, very not easy, English is not my mother tongue, maybe there are many grammatical mistakes, I hope you'll forgive me! Mobile phone can not be used normally I am very sad, I can not contact the parents and friends, can not let them worry about me, I've tried all means, including the upgrade to 6.1, but still can not solve the problem, I think maybe I am in China, so can not be used normally, at this moment I am very anxious, because of the time difference, it is later I can send mail, you can see it, please help me, a Chinese student's request!
I tried all the possible solutions from the Internet, and the Official solution offered by Apple (http://support.apple.com/kb/TS4459), but it doesn't seem to work.
Will Apple help me with this issue? Please do.THANK YOU VERY MUCH!!!

We are not Apple, and Apple does not unlock phones. Sprint will unlock phones, but you have to qualify. One of the qualifications is to have been a customer in good standing for a period of time. You can check their website for what that is. After that, they can unlock the GSM side of the phone for International use, that is it. If you are on a CDMA carrier, then it cannot be unlocked. Are you trying to use a local SIM card in China?
Your only option is to contact Sprint to see if you qualify for an unlock. Only they can unlock it. Sprint is one of the poorest choices to take to another country.

What will i do..there is a message show, "your device in not more eligible to create a free i cloud acount"..and when i try a new one it ask an account number, but i dont have...can you help me with this issue..

What will i do..there is a message show, "your device in not more eligible to create a free i cloud acount"..and when i try a new one it ask an account number, but i dont have...can you help me with this issue..?
I try also my old icloud user but its not recognizing the accoun...

What will i do..there is a message show, "your device in not more eligible to create a free i cloud acount"..and when i try a new one it ask an account number, but i dont have...can you help me with this issue..?
I try also my old icloud user but its not recognizing the accoun...

Plz help me solving following issues

Hi SD experts,
Plz help me solving following issues
1) What do you mean by POD(proof of delivery) what is the use of pod? What are the con figuration you done in your project?
2) When I am punching order after entering data like material No and quantity system should pop-up a screen of delivery date and status and invoice data and details, How can we configure this?
3) Client requirement is he want horizon period in days format. but standard sap system It's in months format(gray mode). how can we change months to days?
4) Quotation has been created for product-D, 10 quantities, sales order is created with reference to the quotation, system copies 10 quantities in sales order. How do you restrict in sales order end user should not change quantities, system should not allow for changes by en user?
5) when i creating the sales order the system show error "No customer master record exist for sold to party". How to rectify it?
suitable solutions will be rewarded
thansx & regards

hi,
Proof of delivery (POD) is an instrument involved in business processes in which an invoice is issued only after the customer has confirmed the delivery's arrival. In addition to the proof of delivery itself, you can also record the POD date, POD time, the actual quantity that arrived and the reason for possible differences in quantities. This is especially important for deliveries where the delivery quantity varies because of the nature of the goods or for which the exact delivery quantity is unknown from the start.
You are now in a position to issue an accurate invoice based on the customer's confirmation of goods received. You no longer need to create credit memos. The reasons for deviation that occur most frequently in "real world" scenarios such as stock shrinkage, theft, certain characteristics of goods (volatility, for example), and transportation damage are recorded and analyzed in the system. This analysis is especially valuable when you are negotiating with forwarding agents, vendors, or customers, since all deviations can be reflected
With regards
Rajesh

Hey guy can you please help me with this issue PLEASE!

Hey Apple can you please help me with this issue, i have a iPhone 3gs and when i put my sim card into the iPhone it makes iphone 3gs shut down suddenly how do i fix that?
iPhone version: 6.0.1
service provider: Vodafone nz

You could restarting your phone that sometimes fixes issues
Hold down the Sleep/Wake button and the home button together until the apple logo appears (ignore the ON/OFF slider) then let both buttons go and wait for phone to restart (no data will be lost).

I have a Excel file which has lots of PDFs embed as a link. When i converting to PDF the embed links are not working. Please help to slove this issue.

I have a Excel file which has lots of PDFs embed as a link. When i converting to PDF the embed links are not working. Please help to slove this issue.e

I am also looking alternative way using inDesign to create the embed link as like as excel. is there any possible? Thanks for you reply

HELP! Variation on Standby issue

Similar Messages

Maybe you are looking for