Help with Airport Extream Card in PowerMac G5

Hello,
I have purchased a used Power Mac G5 with the following hardware:
Model Name: Power Mac G5
Model Identifier: PowerMac7,3
Processor Name: PowerPC G5 (3.0)
Processor Speed: 2.5 GHz
Number Of CPUs: 2
L2 Cache (per CPU): 512 KB
Memory: 2.5 GB
Bus Speed: 1.25 GHz
Boot ROM Version: 5.1.8f7
While it works perfectly, the machine didn't come with an airport card which I installed:
Wireless Card Type: AirPort Extreme (0x14E4, 0x4E)
Wireless Card Locale: USA
Wireless Card Firmware Version: Broadcom BCM43xx 1.0 (4.170.25.8)
The machine appears to recognize the airport card and I can "see" my home network but can not connect to it. When I enter the WEP password, it just fails to connect. I have 2 other macs in the house (and an iPhone) along with an HP windows laptop that connect to this network without issue, so I am confused.
I think there are (at least) 2 variables that I am unsure of:
One: Do I have the right airport card? As best I can tell, I do. But if anyone can tell from the hardware info I copied above, I'd welcome any info. I did see some posts about "late model dual core" G5s (labeled as model 10,x in system profiler) that needed a different card. I took the airport extreme card from one of my other macs (G4 Mirror Door) and the card works perfectly in that machine. I THINK it's the right card for the G5, but can't be sure.
Two: Do I have to install any software to configure the card on the computer.
What else should I be looking for?
Many thanks,
Steve

Hi-
The Airport Extreme card for the MDD FW800 model is the same as in the G5 up to Early 2005.
http://support.apple.com/kb/HT3024?viewlocale=en_US
Did you connect the antenna to the card correctly?
http://manuals.info.apple.com/enUS/AirPortCard.pdf
Did you connect the external antenna (T shaped, plug in rear of tower)?
http://support.apple.com/kb/TA27092
After proper installation, it should just be a matter of making adjustments to your network settings.

Similar Messages

Power Mac G5 fails to start up with Airport Extreme card in.

Hello.
I just received a 'new' Airport Extreme card for my Power Mac G5 1.8 (900fsb). I just installed it and it failed to start up with it in. The mac started up but without my Apple LCD and any USB devices. I did a PMU reset on the logic board and took out the Crucial 3rd party 512mb RAM and tried again but it won't start up. When I take the card out it's business as usual.
Is it the card or the mac that's at fault? Has anyone had this problem too?
Your help will be greatly appreciated.

This problem can happen if:
- the card has not been fully seated into its socket (doing that can take a firm push) or if you installed the card upside down
- the card is defective
- the card socket in the PowerMac G5 has broken or bent contact pins
Check the installation you did with:
http://www.info.apple.com/usen/cip/pdf/g5/apec_c.pdf
If you are sure the card has been properly installed, you are gong to have to either (a) try a different Airport Extreme card or (b) let an Apple dealer or service center take a look at your PowerMac G5.

Very high latency on my MBP 3,1 (mid 2007) with airport extreme card 0x168C

Hi
I wanted to let you know that i filled a bug report concerning a problem involving a MacBookPro3,1 and my airport extreme card (AirPort Extreme (0x168C, 0x87) Firmware Version 1.4.16.2)
If you've got any feedback, please feel free to share it with me.
Here's the bug report:
Hello
I'm experiencing very high latency on my MBP when connected using Wi-Fi in my living room and I believe this is a software bug.
This is the trace of my ping test to my router (5m from me):
macbookpro:~ laurent$ ping 192.168.0.254
PING 192.168.0.254 (192.168.0.254): 56 data bytes
64 bytes from 192.168.0.254: icmp_seq=0 ttl=64 time=1536.229 ms
64 bytes from 192.168.0.254: icmp_seq=1 ttl=64 time=536.642 ms
64 bytes from 192.168.0.254: icmp_seq=1 ttl=64 time=3444.466 ms (DUP!)
64 bytes from 192.168.0.254: icmp_seq=2 ttl=64 time=2547.260 ms
64 bytes from 192.168.0.254: icmp_seq=3 ttl=64 time=2671.552 ms
64 bytes from 192.168.0.254: icmp_seq=4 ttl=64 time=1671.272 ms
64 bytes from 192.168.0.254: icmp_seq=5 ttl=64 time=2619.991 ms
64 bytes from 192.168.0.254: icmp_seq=6 ttl=64 time=1619.350 ms
64 bytes from 192.168.0.254: icmp_seq=7 ttl=64 time=2362.474 ms
64 bytes from 192.168.0.254: icmp_seq=8 ttl=64 time=1362.662 ms
64 bytes from 192.168.0.254: icmp_seq=9 ttl=64 time=363.461 ms
64 bytes from 192.168.0.254: icmp_seq=10 ttl=64 time=1407.557 ms
64 bytes from 192.168.0.254: icmp_seq=11 ttl=64 time=1020.437 ms
64 bytes from 192.168.0.254: icmp_seq=12 ttl=64 time=119.570 ms
^C
--- 192.168.0.254 ping statistics ---
14 packets transmitted, 13 packets received, +1 duplicates, 7% packet loss
round-trip min/avg/max/stddev = 119.570/1663.066/3444.466/937.468 ms
These are the details of my network when alt clicking on the network icon:
ca:69:50:37:c7:b2
Channel: 5
RSSI: -54
Transmit Rate: 54
I'm using Channel 5 where my router is the only device available (checked with iStumbler and KissMac).
I compared these results with another computer sitting at the same place:
This is the trace of my ping test to my router using a PC laptop:
C:\Documents and Settings\Laurent>ping -t 192.168.0.254
Envoi d'une requête 'ping' sur 192.168.0.254 avec 32 octets de données :
Réponse de 192.168.0.254 : octets=32 temps=2 ms TTL=64
Réponse de 192.168.0.254 : octets=32 temps=2 ms TTL=64
Réponse de 192.168.0.254 : octets=32 temps=3 ms TTL=64
Réponse de 192.168.0.254 : octets=32 temps=4 ms TTL=64
Réponse de 192.168.0.254 : octets=32 temps=3 ms TTL=64
Réponse de 192.168.0.254 : octets=32 temps=4 ms TTL=64
Réponse de 192.168.0.254 : octets=32 temps=2 ms TTL=64
Réponse de 192.168.0.254 : octets=32 temps=3 ms TTL=64
Réponse de 192.168.0.254 : octets=32 temps=3 ms TTL=64
Réponse de 192.168.0.254 : octets=32 temps=6 ms TTL=64
Réponse de 192.168.0.254 : octets=32 temps=4 ms TTL=64
Réponse de 192.168.0.254 : octets=32 temps=8 ms TTL=64
Réponse de 192.168.0.254 : octets=32 temps=4 ms TTL=64
Réponse de 192.168.0.254 : octets=32 temps=4 ms TTL=64
Réponse de 192.168.0.254 : octets=32 temps=4 ms TTL=64
Réponse de 192.168.0.254 : octets=32 temps=1 ms TTL=64
Statistiques Ping pour 192.168.0.254:
Paquets : envoyés = 16, reçus = 16, perdus = 0 (perte 0%),
Durée approximative des boucles en millisecondes :
Minimum = 1ms, Maximum = 8ms, Moyenne = 3ms
(PC: Win XP SP3 with Linksys Wi-Fi card)
Obviously, my Mac has very high latency where my PC works as expected.
I tried resetting the PRAM, but i didn't affect my results.
I tried updating Airport with the latest AirPort Client Update (http://support.apple.com/downloads/AirPortClient_Update_for_MacBook_and_MacBookPro), but my hardware wasn't eligible for that update (Mid 2007 MacBookPro).
I believe this isn't a hardware bug because i get acceptable ping results when next to my router or in other rooms of my flat.
Can you help me with that bug ?
Regards,
Laurent
Hardware Overview:
Model Name: MacBook Pro
Model Identifier: MacBookPro3,1
Processor Name: Intel Core 2 Duo
Processor Speed: 2.2 GHz
Number Of Processors: 1
Total Number Of Cores: 2
L2 Cache: 4 MB
Memory: 2 GB
Bus Speed: 800 MHz
Boot ROM Version: MBP31.0070.B07
SMC Version (system): 1.16f11
Serial Number (system): W874551DX91
Hardware UUID: 00000000-0000-1000-8000-001B63B19195
Sudden Motion Sensor:
State: Enabled
AirPort:
Type: AirPort
Hardware: AirPort
BSD Device Name: en1
IPv4 Addresses: 192.168.0.2
IPv4:
Addresses: 192.168.0.2
Configuration Method: DHCP
Interface Name: en1
NetworkSignature: IPv4.Router=192.168.0.254;IPv4.RouterHardwareAddress=00:07:cb:3e:04:ef
Router: 192.168.0.254
Subnet Masks: 255.255.255.0
DNS:
Server Addresses: 212.27.40.241, 212.27.40.240
DHCP Server Responses:
Domain Name Servers: 212.27.40.241,212.27.40.240
Lease Duration (seconds): 0
DHCP Message Type: 0x05
Routers: 192.168.0.254
Server Identifier: 192.168.0.254
Subnet Mask: 255.255.255.0
Proxies:
Exceptions List: *.local, 169.254/16
FTP Passive Mode: Yes
Ethernet:
MAC Address: 00:1e:52:72:05:2c
Media Options:
Media Subtype: Auto Select
AirPort Card Information:
Wireless Card Type: AirPort Extreme (0x168C, 0x87)
Wireless Card Locale: Worldwide
Wireless Card Firmware Version: 1.4.16.2
Current Wireless Network: kalamar
Wireless Channel: 5

Ok, I must have jinxed myself.
High latency with my Negear WPN824v3. As previously mentioned, the other wireless computers connect fine. Latency remains regardless of the power connected or not.
Please advise.
PING 192.168.0.1 (192.168.0.1): 56 data bytes
64 bytes from 192.168.0.1: icmp_seq=0 ttl=64 time=11.607 ms
64 bytes from 192.168.0.1: icmp_seq=2 ttl=64 time=7280.106 ms
64 bytes from 192.168.0.1: icmp_seq=3 ttl=64 time=9209.019 ms
64 bytes from 192.168.0.1: icmp_seq=4 ttl=64 time=8237.475 ms
64 bytes from 192.168.0.1: icmp_seq=5 ttl=64 time=7262.603 ms
64 bytes from 192.168.0.1: icmp_seq=8 ttl=64 time=4313.763 ms
64 bytes from 192.168.0.1: icmp_seq=9 ttl=64 time=3336.361 ms
64 bytes from 192.168.0.1: icmp_seq=10 ttl=64 time=2339.579 ms
64 bytes from 192.168.0.1: icmp_seq=11 ttl=64 time=1344.110 ms
64 bytes from 192.168.0.1: icmp_seq=12 ttl=64 time=345.132 ms
64 bytes from 192.168.0.1: icmp_seq=13 ttl=64 time=1191.119 ms
64 bytes from 192.168.0.1: icmp_seq=14 ttl=64 time=3969.730 ms
64 bytes from 192.168.0.1: icmp_seq=15 ttl=64 time=3992.111 ms
64 bytes from 192.168.0.1: icmp_seq=16 ttl=64 time=3692.648 ms
64 bytes from 192.168.0.1: icmp_seq=17 ttl=64 time=2927.634 ms
64 bytes from 192.168.0.1: icmp_seq=18 ttl=64 time=2130.216 ms
64 bytes from 192.168.0.1: icmp_seq=19 ttl=64 time=1437.424 ms
64 bytes from 192.168.0.1: icmp_seq=20 ttl=64 time=2385.203 ms
64 bytes from 192.168.0.1: icmp_seq=21 ttl=64 time=1393.622 ms
64 bytes from 192.168.0.1: icmp_seq=22 ttl=64 time=396.783 ms
64 bytes from 192.168.0.1: icmp_seq=23 ttl=64 time=1.295 ms
64 bytes from 192.168.0.1: icmp_seq=24 ttl=64 time=115.793 ms
64 bytes from 192.168.0.1: icmp_seq=25 ttl=64 time=3.137 ms
64 bytes from 192.168.0.1: icmp_seq=26 ttl=64 time=10.240 ms
64 bytes from 192.168.0.1: icmp_seq=27 ttl=64 time=2.709 ms
64 bytes from 192.168.0.1: icmp_seq=28 ttl=64 time=9.958 ms
64 bytes from 192.168.0.1: icmp_seq=29 ttl=64 time=1818.371 ms
64 bytes from 192.168.0.1: icmp_seq=30 ttl=64 time=1470.613 ms
64 bytes from 192.168.0.1: icmp_seq=31 ttl=64 time=472.520 ms
64 bytes from 192.168.0.1: icmp_seq=32 ttl=64 time=2255.417 ms
64 bytes from 192.168.0.1: icmp_seq=33 ttl=64 time=18198.039 ms
64 bytes from 192.168.0.1: icmp_seq=34 ttl=64 time=23288.761 ms
64 bytes from 192.168.0.1: icmp_seq=35 ttl=64 time=25150.840 ms
64 bytes from 192.168.0.1: icmp_seq=36 ttl=64 time=26813.832 ms
^C
--- 192.168.0.1 ping statistics ---
63 packets transmitted, 34 packets received, 46% packet loss
round-trip min/avg/max/stddev = 1.295/4906.111/26813.832/7241.136 ms

Sigh... i need some specific help with airport wireless connectivity

hi. long time reader, first time poster. Pretty much comes down to a failure in how to search... so, links to answers are a-ok with me!
here's the problem, PowerPC 970 (2.0ghz, 2 cpu Power Mac G5 for search string) that does not like the airport extreme card that i'm trying to install. using the apple documentation, and using card model A1026 emc# 1951
machine will not boot after card installation. running fresh install of 10.5 with 10.5.8 and latest airport install.
any help as to what i'm doing wrong here and why we're not booting up? Thanks! if there's a database that has a list of compatible cards by machine, please please please linky
TIA

Hi-
One Airport Extreme card, M8881 (LL/A is US model) PN#652-0817:
http://www.smalldog.com/product/73422/atfgc
http://support.apple.com/kb/HT3024
Airport Installation:
http://manuals.info.apple.com/en/AirPort_Card.pdf
The Bluetooth module is separate from the Airport Extreme card:
http://www.yourmacstore.com/shop/shopexd.asp?id=467&bc=no

Short short range with airport extreme card

Hello,
my neighbour bought an Airport Extreme Card for his iBook, in order to connect (wireless) to my airport express base station. (our flats are adjacent). His mac is an iBook G4 with OS X 10.3.4
We installed the card, the airport software, but no network appeared in the network menu...
We had to move to my flat and take his iBook very close from the Airport Express Base Station... and then, we were able to connect. But the quality of connection was very poor.
The network works fine, my computer and the one of my Wife (a Mac and a PC) connect perfectly.
Do you have an idea of what could be wrong ?
Compatibility between the iBook and the card ?
Card with a defect ?
Software problems ?
Thank you a lot for helping.

Charles, Welcome to the discussion area!
Did you properly connect the antenna wire to the AirPort Extreme card? Look at the photos in KB 108039, Properly attaching the antenna on an AirPort Extreme Card. It can take more force than most people think to get the antenna wire properly connected.

Cant connect to Netgear WPN824 with Airport Extreme Card

Hi,
I have a Netgear wireless router. I can connect to the router without a problem when I hard wire it. When I go wireless the Mac doesnt even recogonize the router. I have no security right now, so I could try to connect the easiest. This is a brand new Airport extreme card that I installed tonight in my Imac g5. Using OS 10.4.10. Please help!!! Thanks!!!
I would think it would at least be able to recognize the network (which the name is being broadcasted). But it doesnt even show up.

Did you connect the antenna wire to the AirPort Extreme card?
Compare the antenna wire installation with the photos in KB 108039, Properly attaching the antenna on an AirPort Extreme Card.

Need help with Airport Express and so on.

Ok so my main problem before getting into what I need help with here is that our MacBooks and now my iPhone 6 plus isn't staying online. Keep getting booted off and then I either have to select the network again or it will eventually go back on. If anyone has a solution or so please feel free to answer that as well. I'm running on Roadrunner with a Netgear 600 wireless router and a motorola modem. Both of which I'll leave the link to below for a better look.
My Main Question: So I'm looking at a new wireless router mainly and possibly a new modem. I know Apple products are trustworthy but how good is the Airport Express and other Airport products. Also what is the Maximum speed and Maximum data speed for the cheapest express station and if anyone knows the speeds of the other devices it would be greatly appreciated.

DSL Router to Netgear 5-port Switch and I used the switch to connect to Airport Extreme, TV, Blue-Ray DVD player and DirecTV Receiver.
The AirPort Extreme base station (AEBS) is a router so it will do what you need.
You need to reconfigure your setup. Connect the WAN port of the AEBS to the DSL router. Then connect the Netgear switch to one of the LAN ports on the AEBS. The AEBS will properly share the connection.

Power Mac G3 Pismo with Airport wireless card in Mac OS X 10.4 won't connect to wireless network with newest Airport Extreme Base Station set at WPA Personal/WPA 2 Personal encryption.

My Power Book G3 Pismo with an Airport wireless card running Mac OS X 10.4.11 will not connect to my new Airport
Extreme Base Station using WPA Personal/WPA 2 Person encryption. The Airport firmware is version 9.52. From
posts I've read online at different places indicates the Airport card should support the WPA encryption. Perhaps the problem
is the Base Station is using a combination setting and the fault is in the base station?
Thanks for any suggestions

Perhaps an inexpensive usb wireless adapter would work as well?
This is probably the simplest way to get the G3 connected to the wireless network.
I'll have to read up on getting an express and using it as a wireless bridge as I am unfamiliar with the concept.
The new AirPort Extreme is broadcasting a wireless signal.
A new AirPort Express could be located close to the G3. The Express will pick up the wireless signal from the AirPort Extreme, then provide an Ethernet connection to the G3 though a short Ethernet cable.
This can work very well......IF.....you keep the G3 at a fixed location, since it will always be connected to the AriPort Express using an Ethernet cable.
I do have an old Linksys Wireless G router. I wonder if that would work?
In theory, yes. But it would have to use much older WEP "security", which is easily cracked in minutes using free tools available on the Internet. So, anyone who really wanted to get on the network could do so. It's an option, but not a very good one.

Can a non apple network be extended with airport extream?

I have a Verison Fios router and am contimplating buying an airport extream or express. I was wondering if I can extend my network with either one of these routers and if so, how to go about doing this. Thanks.

so if I understand you correctly, you are saying that it is actually possible, but it may take a lot more work on my end?
In almost all cases, it is simply not possible.
There are only a handful of routers that are known to be compatible with Apple's version of WDS.
Belkin F5D7230-4 and F5D7231
BT Voyager 2091 or 2100
Buffalo WGR-G54
Linksys WRT54G or WRT54GS (not latest versions v5)
Netgear WGR614 v6
SMC (one model - don't know the model number)
Thompson 585v6 wireless router (40 bit WEP works but stronger encryption does not)
Most of these models are 4-5 years old, or older.

Need help with buying graphics card and ram for MSI 865PE NEO 2-V

Hi,
I want to buy 1GB of ram for motherboard MSI 865PE NEO 2-V I need help with finding correct parts.
I also want to buy 512Mb or 1GB graphics card.
as i said before i need help with finding correct ones so they match motherboard, I would appreciate if any one would post link to cheap and fitting parts.
I found graphics card allready, i just need to know if it will fit.
the card is
NVIDIA GeForce 7600 GS (512 MB) AGP Graphics Card
Thanks for help.

here you can see test reports for your mobo:
http://www.msi.com/product/mb/865PE-Neo2-V.html#?div=TestReport

Is Duel Ethernet Airport Base compatible with Airport Extreme Card?

I am about to upgrade to the new Macbook Pro 15" from my Titanium G4. I currenty have the original Airport card and the dual ethernet Airport Station.
Question - will the new Pro with the Airport Extreme card be compatible with the old base station?
If it will, what would be the advantages of upgrading to a new Extreme Basestation?
maginme
Macbook Pro 15" 2.16 Mac OS X (10.4.7) Powerbook G-4 Titanium

magicnme, Welcome to the discussion area!
Question - will the new Pro with the Airport Extreme card be compatible with the old base station?
Yes, the MacBook Pro can connect to a 802.11b base station like the Dual Ethernet (aka snow) AirPort base station (ABS).
If it will, what would be the advantages of upgrading to a new Extreme Basestation?
The AirPort Extreme base station (AEBS) offers a USB printer port for wireless printing.
The AEBS offers WPA and WPA2 wireless encryption.
Also if you have other computers on your local network, large file transfers between your computers will be faster.

Powerbook will not startup with airport extreme card installed

I have a 2 year old powerbook using 10.3.9 an djust of late when my airport card is in, The computer just sends me to the open Firmware right after i turn it on.when i type mac-boot it comes up with a broken folder icon. however when i take my card out i dont have a problem. is there a wa i can ues my computer and the airport at the same time? what do you think i should do.

it is a 867 mhz g4 with 256 mb ddr ram. 40 gb hd and
a combo drive. i hope that is helpfull.
This PowerBook requires the original Airport card, you can not use the Airport Extreme card in that PowerBook, any attempt to do so could result in damage to both the card and the PowerBook.
Either change the AE card for an original Airport or use a third party 802.11g card in the cardbus slot.
iFelix

Slow Speedtest results with Airport Extreme Card

Hi,
We just upgraded our internet to a 5G network with TWC. All the devices in our home are now speedtesting at 100 mb/s wonderfully.
Except one.
My Mac Pro 8 Core 2009 4,1. Running OSX 10.8.5
The mac pro is speedtesting at only 30 mb/s while everything else (MBP, MBA, iphone 5) all speddtesting at 100 mb/s. Alla re connected to the new network.
Is the problem the older airport extreme card? Or is there something I can do in settings or firmware upgrade to sort this?
Here are the specs of the Airport extreme card on the MP:
Card Type:    AirPort Extreme (0x14E4, 0x8E)
Firmware Version:    Broadcom BCM43xx 1.0 (5.106.98.100.17)
Locale:    FCC
Country Code:    US
Supported PHY Modes:    802.11 a/b/g/n
Supported Channels:    1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140, 149, 153, 157, 161, 165
Wake On Wireless:    Supported
AirDrop:    Supported
Status:    Connected
Thanks!

tek_uk, Welcome to the discussion area!
(a) Did you connect the external 'T' AirPort shaped antenna to the back our your G5? This antenna shipped with your Power Mac G5.
(b) Compare the antenna wire connection at the AirPort Extreme card with the photos in KB 108039, Properly attaching the antenna on an AirPort Extreme Card.

Connect to router with airport extreme card

Hello, I just oredered a iBook G4 off of Amazon (1.33 GHZ, 1 GB RAM, Combo, 12") with an Airport Extreme card. Can this connect to my Linksys WPA wireless router? I'm new with Macs, so sorry if noobish.

AirPort Extreme Card M8881LL/A
802.11 b/g
Frequency Range 2.4 GHz
Data Rate Up to 54Mbps
Channel Support 802.11b/g:
US/Canada/Latin America/Taiwan: 1-11
Japan: 1-14
Other countries: 1-13
Security 40/128-Bit WEP, WPA, NAT Firewall, MAC address filtering
Antenna Internal
Operation Distance 150 feet
Transmission Power 15dBm

Trickling down connection with airport extreme "card"

I recently bought an airport extreme card for my mac pro (older model, 2008?)
Anyways, the problem is that i live in an apartment that offers free wireless. Naturally i suspect the signal to be weak as it has been for a laptop ive used here before. Airport works fine except that when i connect and have a download it starts out high like around 200kb/sec and then slams down to about 12kb/sec then slowly trickles down to a request time out. (I am unable to update because of it.) At first i thought the problem was just well...the apartment, then booted up into Vista and started a download and it keeps a steady pace of about 9kb/sec without timing out.... I tried connecting the 1 and 3 wires, as well as the 2 and 3 and pretty much i noticed no difference. Any suggestions? What firmware is better to use for this?

thnx for the suggestion. That's not my problem.
I do have WiFI connection. So I am already connected tot the AE....the part I do not understand is why I can not connect to the external harddisk that is connected to the AE.
Especially because:
1) It used to be connected
2) My other macbook does connect to the external harddisk

Help with Airport Extream Card in PowerMac G5

Similar Messages

Maybe you are looking for