Help with Bluetooth internet using PBG4 and Nokia, please!

I have a new Powerbook G4 equipped with Airport and Bluetooth. I'm already set up to use Airport with my standard ISP (Virgin's monthly dial up service, with a specified phone line). We don't have broadband in our village.
I'd like to be able to use my bluetooth phone as a modem when I'm on the road, and can't find a WiFi hotspot. I'd probably be using a PAYG service like Fasthosts or net2roam. Any recommendations or suggestions would be welcome!
I don't have a GPRS package activated, but I just want to occasionally check or send an e-mail, so all I need is to use the phone as a modem.
The G4 and 6320i go through the communications dialogue with an ID number, etc. they then recognise each other but when trying to connect with a couple of different ISPs (one of them was Fasthosts) I get a message that there was no carrier signal.
Do I need to pick a different ISP?
Do I need to be less of a cheapskate and set up GPRS or Orange World, or whetever?
Do Orange need to set up my phone to do something?
Do I need to download some kind of 'script' whatever that is?

OK:
You can do it via GPRS (costs money, basically) or via GSM/CSD
I have GPRS working very well now - it was very straightforward and gives connection speeds equivalent to dial up.
My phone needed activating for CSD connection, via a series of SIM updates, and needed to use third party Modem scripts because those included on the G4 were poor.
I still haven't managed to connect via GSM/CSD but anticipate a VERY slow 9 kbps connection speed, and infinitesimal cost.

Similar Messages

Help with queries about boot camp and partition, please.

Hi, I am hoping to partition my HDD. I have done this before, when I first got my macbook but got rid of it, and now I can't fully remember the do's and don'ts' of boot camp. I just need a few questions answered before I take any action.
1. I have a 120GB HDD with about 15GB free space. If I partition the drive will I lose any data on my existing HDD?
2. What is the minimal amount of space I can partition the drive and install Windows?
(I have a copy of Windows XP SP2, and really only need to install it for the use of one program that isn't available on the Apple operating systems.)
3. I tried using Parallels in which Windows took up about 6GB, will it be about the same again? I uninstalled it because I found it to lag a bit.
If you can help with any of these queries I would really appreciate it, thanks!

Maybe you should first get a larger drive; you don't have much more than the minimum 10% free space that Mac OS needs.
Retry with Sun's VirtualBox. Maybe you just need more memory.
Lose data? Step #1: backup.
You may need to backup and erase your hard drive and then restore.
I'd invest in 300GB drive though.

Help with a query using ISNULL and RTRIM in the same select statement

What I'm trying to accomplish is to blend the following two statements together:
ISNULL (EMail_Address, '') As Matrix_Member_Email
AND
RTRIM (EMail_Address) as Matrix_Member_EMail
So that if the email address is NULL, it gets changed to blank and I still need to RTRIM the other entries and use the column header of Matrix_Member_Email.
I've tried:
ISNULL ((EMail_Address, '') (RTRIM (EMail_Address)) as Matrix_Member_EMail
Any help would be greatly appreciated.
Thank you,

I'm sorry. Here is the query:
--Declare @EMail_Address nvarchar(100) = null
Select SVAssociationID.R_ShortValue as MATRIX_AssociationID, Matrix_Modified_DT as Matrix_LastModified
  ,RTRIM (MLS_ID) As Matrix_MLS_ID
  , ISNULL(EMail_Address, '') AS MATRIX_member_Email
  ,RTRIM (EMail_Address) as Matrix_Member_EMail
  --,RTRIM( LTRIM( ISNULL (@EMail_Address, '') ) ) as Matrix_Member_EMail
  ,Last_Name AS MATRIX_LastName, Nickname AS MATRIX_NickName
  FROM    dbo.Agent_Roster_VIEW a
        LEFT JOIN dbo.select_values_VIEW SV ON a.Status_SEARCH = SV.ID
        LEFT JOIN dbo.select_values_VIEW BillType ON a.Bill_Type_Code_SEARCH = BillType.ID
  LEFT JOIN dbo.select_values_VIEW SVAssociationID ON A.Primary_Association_SEARCH = SVAssociationID.ID
WHERE   Status_SEARCH IN (66,68)
    Order by MLS_ID
Results:
MATRIX_AssociationID
Matrix_LastModified
Matrix_MLS_ID
MATRIX_member_Email
Matrix_Member_EMail
MATRIX_LastName
MATRIX_NickName
STC
09/02/14
CCWILLI
[email protected]
[email protected]
Williams
Christine
STC
09/12/14
CCWORSL
[email protected]
[email protected]
Worsley
Charlie
STC
09/02/14
CCYROBIN
NULL
Robinson
ECBR
09/02/14
CDABLACK
[email protected]
[email protected]
Black
Dale
STC
09/02/14
CDABRADY
[email protected]
[email protected]
Brady
David
Thank you,

Help with logo size using illustrator and photoshop

hi everybdy, can somebody please explain to me how to know the right WIDTH, HEIGHT and PIXELS/INCHES when designing a business card, a post card, or a banner????????????????????????

I could be misunderstanding your question, but it seems to me that each logo application should be designed/sized on its own, according to the size of the document (3-1/2" x 2" on a business card for example). For a business card, make it look nice on the card. For a banner, make it look nice, within the (much larger) bounds of the banner size.
There is no "prescribed size" for each individual application. Each implementation of the logo should be sized according to the size of its document, what else is on the page with the logo, and what looks "good" to the designer (and the client). :+)
BTW, this is the Illustrator forum, and I suspect you were referring to pixels (?). For actual printed items using only AI vector art (such as a logo), pixels are irrelevant. (The vector artwork conforms to the resolution of the output device for each application, at the time it is imaged.) With the possible exception of web applications, send vector files (such as actual-sized pdf) to your print supplier.

Hi i would like help with: When I draw circle and add stroke I can not see stroke I use Photoshop CS 5

Hi i would like help with:
When I draw circle and add stroke I can not see stroke
I use Photoshop CS 5

Make sure the stroke is set to a color and not to the symbol that appears here for Fill

Need help with how to reset bios and admin password to reformat hard drive in 8440p elitebook.......

need help with how to reset bios and admin password to reformat hard drive in 8440p elitebook? removal of cmos, resetting laptop, using cccleaner, windows password recovery and hiren's was noneffective, any help is appreciated. thanks

Hi,
As your notebook is a business class machine, security is more stringent - the password is stored in non-volatile memory and there are no 'backdoor' passwords. Your best option would be to contact HP regarding this.
Regards,
DP-K
****Click the White thumb to say thanks****
****Please mark Accept As Solution if it solves your problem****
****I don't work for HP****
Microsoft MVP - Windows Experience

After loading the internet using Firefox AND then selecting NEWS and a delay the Error "The MSN toolbar has encountered an error. etc" occurs. Also, when browsing some searches are "REDIRECTED"!

After loading the internet using Firefox AND then selecting NEWS and a delay the Error "The MSN toolbar has encountered an error. etc" occurs. Also, when browsing some searches are "REDIRECTED"!
== This happened ==
Every time Firefox opened
== Hard to say but have been trying to diagnose for at least a week.

Original message wouldnt post with attachments - trying again....
Attachments:
secondclickheredialog.jpg ‏40 KB
FirstDialog.jpg ‏19 KB
Firstclickheredialog.jpg ‏16 KB

I shared one contact with a friend using message and she got my other messages with others.

I am using a iPhone 4 on iOS 7.0.4. I shared a contact with my friend using message and she got my other messages between my other friends, and she also found all her contacts are deleted as well. Can someone help? what happened to my phone? is it safe for me to message others?

You prob hit Delete All at the top instead of the trash can at the bottom which will do only the selected msg.
Sorry, unless the entire converstaion is on a backup you can't retrieve it.

So I just updated to the newest update that was available for safari and iTunes but now it won't let me go on the Internet using safari and it also won't let me sync my songs ,,,,,it takes forever to back up my iPad AND my iPod so what can I do ?

So I just updated to the newest update that was available for safari and iTunes but now it won't let me go on the Internet using safari and it also won't let me sync my songs ,,,,,(it takes forever to backup my iPad AND my iPod) so what can I do ?

If you're on windows try the following:
This worked for me an hour ago and has allowed me to sync ok. Still haven't tried downloading the new version 5 to the phone yet as I'm still backing up photos etc just in case.
1. Quit itunes
2. Start an elevated command prompt (Start Menu -> All Programs -> Accessories -> right click Command Prompt -> Run as Administrator)
3. Once in the command prompt type the following 3 words starting where your cursor is flashing: netsh winsock reset
4. press ENTER
5. Reboot your machine
6. Restart itunes & connect device to sync
7. Good luck

Can anyone help with issue whereby Music, Podcasts and Audiable Book Apps keep stopping when listing via Headphones following IOS 7.01 Updates on Iphone 4?

Can anyone help with issue whereby Music, Podcasts and Audiable Book Apps keep stopping when listing via Headphones following IOS 7.06 Updates on Iphone 4?
I have tried the following all ready:
Resetting Phone
Resetting Settings on phone
Change Headsets to speakers
Reinstalled Phone
Updated to IOS 7.1
No of the above has resolved the issue does anyone have any ideas?

Can anyone help with issue whereby Music, Podcasts and Audiable Book Apps keep stopping when listing via Headphones following IOS 7.06 Updates on Iphone 4?
I have tried the following all ready:
Resetting Phone
Resetting Settings on phone
Change Headsets to speakers
Reinstalled Phone
Updated to IOS 7.1
No of the above has resolved the issue does anyone have any ideas?

I am having problems transefering contacts to my I pod when syncing the message comes back with contact in use by I pod please close and try again, please could you let me know how to close contacts on the pod or is there a setting that is wrong etc,

I am having problems transfering contacts to my I pod when syncing the message comes back with contacts in use by I pod please close and try again, please could you let me know how to close contacts on the pod or is there a setting that is wrong etc, i have restored the device. if i go to contact via settings the screen comes on for about 2 seconds and then goes off - Help

Single click on the Home button. Then double click on the Home button. In the recently used row, touch and hold the Contact app till they start to wiggle and then tap the minus sing by the contacts app.
Also make sure the Contact program on your computer is closed.

Need help with premiere pro cs6 having performance issues please help

need help with premiere pro cs6 having performance issues please help

Welcome to the forum.
First thing that I would do would be to look at this Adobe KB Article to see if it helps.
Next, I would try the tips in this ARTICLE.
If that does not help, a Repair Install would definitely be in order.
Good luck,
Hunt

Need help with Leopard: screen saver glitch and very slow internet

I performed an erase and install leopard 10.5.1 on my upgraded G4 AGP Sawtooth Computer several times. Has anyone had the following 2 problems with leopard and any suggestions to solve them? Apple telephone support has not helped thus far. The Issues include:
1-Internet surfing (Safari and Firefox) is extremely slow worse than dial-up. I have verizon fios. Upgrading leopard to 10.5.3 and upgrading Safari did not help and took about 10 hours to download when it should have been quick.
2- A screen saver glitch: When I click on screen saver such as beach I get this message. " Screen saver "beach" did not load properly. Error Can't load bundle" When I click on the screen savers folder, there is nothing in it. Desktop pictures work fine.
Computer upgrades include:
Processor-OWC Mercury Extreme [email protected] 2MB L3 Cache
2GB memory
Two 120GB hardrives.
Firmware is updated.
Thus far, all this was done:
Apple exchanged install disk. Same results with new disk.
I ran disk utility and everything is ok including permissions.
I performed a safe boot with apple support.
I Threw away cache folder and com.apple.safari.plist
Tried firefox with same very slow surfing results.
I even checked file system structure problem fsck -yf. Everything was ok
Thanks in advance for any suggestions.

Althought the behavior is the same in all three accounts, if all are working accounts I would suspect there is something all of them have installed that could be the source of the problem. Try creating a new admin account, and leave it just the way Apple creates it--don't add anything nor modify it in any way. Log into that account and see if it works correctly.
If that account is also misbehaving, try restarting, and when you hear the chime hold down the Shift key so that you boot into Safe Mode (you'll see a notice in the splash screen about being in Safe Mode). The boot will take longer (perhaps even considerably longer) as the system runs disk repair, empties some caches, disables all third party startup items, as well as all Apple startup items not strictly necessary for the machine to run. See the menus and Dock now behave correctly.
Since the problem is evidently somewhat intermittent in nature it may take some patience to discover what is wrong. You might also disconnect everything that didn't come with the Mac, reboot, and use only the Apple keyboard and Apple mouse and run for a bit to see how that works. If you are using a third party mouse that required installing something that would be my guess as a "prime suspect" for the cause of the problems.
Francine
Francine
Schwieder

Please Help! Problem with 'whistle' when using Audition and Premeire Pro 1.5 with Audigy

I hope someone can help with this problem. The start of these messages is at the bottom. Any suggestions would be most welcome...Bill Allen
Hi David (00)... Thanks for your reply. I just wanted to let you know
that I am going to post all of this correspondence on as many Creative
forums that I can find in hopes of finding someone that help with this
problem.
I will advise you of the results
Thanks again...Bill Allen
----- Original Message -----
From: "Creative Americas Customer Support"
To: "Bill Allen"
Sent: Saturday, February , 2006 :39 AM
Subject: Re: Creative System Information (English : Adobe Premeire Pro .5
and Adobe Audition) (KMM987992I6636L0KM)
> Sir,
>
> The only time that I've see a random tone being generated as you
> decribe, it was necessary to update the system bios to correct.
>
> While we are able to playback and record with the card and it's included
> software, Adobe continues to not allow you to monitor what you're
> recording. As best we can tell, there's nothing wrong with the card and
> I would urge you to check with Adobe for any "monitor recording"
> switches that may be in their software.
>
> For faster service please reply with previous correspondence when
> replying to this email.
>
> Best Regards
> ,
>
> David (00)
> Team Specialist
>
> Technical Support
> Creative Labs Americas
>
>
>
> To provide feedback on your "Creative Experience" please click on the
> following link:
>
Link removed
>
> This link is provided so that you may provide feedback on your "Creative
> Experience". If you require further troubleshooting or have additional
> questions simply reply to the original mail and we will be glad to
> assist you.
>
> Original Message Follows:
> ------------------------
> Jeen... I appreciate, very much, your reply. But I don't appreciate
> trying
> to be 'ping ponged' back and forth between Creative and Adobe. While I
> realize that you can only deduce a solution from what I tell you, I
> believe
> that if you re-read my description of the problem you will realize that
> the
> problem is with the sound card and it's associated software. Otherwise
> why
> would the system work as expected when it it turned on the next morning?
>
> I would also like to know where the 'tone' comes from. When recording
> video segment (with audio) through the firewire connection of the
> Creative Audidgy 2ZS card, after a short while the audio is replaced with a
> constant tone (as I said, it is about 200 Hz). If I record the video thru the
> Firewire connection and the audio through the 'Line-In' connection,
> there is no problem with the recording the audio track 'tone free'. However,
> sometimes but not always, when the audio is played back the tone will
> appear. This has happened with both Adobe Premeire Pro .5 and Adobe
> Audition. It is not in the audio track of Adobe Premeire Pro .5 or
> Adobe Audition, so the problem must lie with the Creative Audigy 2ZS card or
> it's associated software. I'm sure your audio engineers have knowledge of
> this problem and I would appreciate an answer.
>
> Thanks...Bill Allen
>
> ----- Original Message -----
> From: "Creative Americas Customer Support"
>
> To: "Bill Allen"
> Sent: Friday, February 0, 2006 2:5 AM
> Subject: Re: Creative System Information (English : Adobe Premeire Pro
> .5
> and Adobe Audition) (KMM9780I6636L0KM)
>
>
>> Dear Bill,
>>
>> Thank you for replying back to Creative Technical Support.
>>
>> With regards to your issue, I understand that you are having
> difficulty
>> getting the audio to record from the applications Adobe Premiere Pro
> .5
>> and therefore not sound during the playback.
>>
>> As you have verified that the sound card is working properly with the
>> other applications on recording or playback, this could be due to the
>> improper setup for the audio in the Premiere Pro .5.
>>
>> You may like to refer to Adobe for assistance on the configuration of
>> the audio settings as we are not in a better position to advise you on
>> third party software.
>>
>> Should you have not sound or issues with our software, please feel
> free
>> to contact us so that we can assist you.
>>
>> For faster service please reply with previous correspondence when
>> replying to this email.
>>
>> Best Regards
>> ,
>>
>> Jeen
>> Technical Support
>> Creative Labs Americas
>>
>>
>>
>> To provide feedback on your "Creative Experience" please click on the
>> following link:
>>
Link removed
>>
>> This link is provided so that you may provide feedback on your
> "Creative
>> Experience". If you require further troubleshooting or have additional
>> questions simply reply to the original mail and we will be glad to
>> assist you.
>>
>> Original Message Follows:
>> ------------------------
>> Ronshone... Thanks for your reply.
>>
>> Here is the information you requested:
>>
>> Sound Blaster Audigy 2ZS
>> PID: 0 03 50 00 00 00 02
>> Driver Ver: 2.8.4
>> Firmware : 0.0.0
>> Model: SB.0350
>> Serial Number: MSB0350472004288E
>> Ink stamp: 50SPT470D
>>
>> The Audigy 2ZS is the only sound card installed
>> The Audigy 2ZS card is at least one slot away from the graphics card.
>> The Audigy 2ZS card is one slot away from another card.
>> The Audigy 2ZS card is properly seated in the PCI slot.
>> The PC's internal wires have been moved away from the Audigy 2ZS card
> .
>> The 'on-board' sound is disabled thru the BIOS.
>> The 'on-board' game port is disabled thru the BIOS.
>> The XP Pro operating system is up to date with all updates.
>> There were no background operation going at the time of the tests.
>> The anit-virus program was closed
>> The CPU is not overclocked.
>> And, I am the Administrator.
>>
>> The card came in a Creative retail Box along with the input unit that
>> mounts
>> in the dri've bay. I can't recall what that is called.
>>
>> I have relocated the sound card to a slot that is 4 slots away from
> the
>> graphics card and slot away from another card, in this case an
>> additional
>> IDE dri've controller.
>>
>> I have performed the test you outlined. I found that I had to record
>> using
>> the 'line in' source input. And I had to playback using the 'wave'
>> source.
>> As far as that test is concerned, everything worked. However when I
>> bring
>> up Adobe Premeire Pro .5 I do not hear the audio when capturing, and,
>> even
>> though the audio meters in Premeire Pro in indicate that there is
> audio
>> playing from the audio track on playback, I hear nothing from the
>> speakers.
>>
>> I then brought up the Creative Speaker Settings requester and did a
>> diagnostic test. All tests indicated "pass". But when I click on the
>> 'Speaker Settings' and perform the 'Speaker Test' I hear nothing. I
>> should
>> add that in both mixers, the Creative Surround Mixer and the Play
>> Control
>> mixer, all inputs and outputs are selected (not muted). Also when I
>> performed this same test yesterday the 'Speaker Test' worked fine.
>>
>> On rebooting, the 'Windows XP' sound is heard from the speakers.
>> Bringing
>> up Adobe Premeire Pro .5, the audio played as expected. The 'Speaker
>> Test'
>> in the Creative Surround Mixer also worked as expected.
>>
>> I then recorded the rest of my program using the Adobe Premeire Pro
> .5
>> 'Capture' requester and when I tried to playback from within Adobe
>> Premeire
>> Pro .5 all I got was a constant tone (about 200 Hz), even though the
>> audio
>> meters in Adobe Premeire Pro .5 indicated that the audio was good and
>> had
>> no constant tone.
>>
>> I rebooted the computer and brought up Adobe Premeire Pro .5 and my
>> program. Without making any changes to either mixers, Adobe Premeire
> Pro
>> .5
>> performed, and the sound played, as expected. In the 'Play Control'
>> mixer
>> only the 'wave' was acti've. All the rest were muted. It was the same
>> for
>> the 'Creative Surround Mixer'.
>>
>> I am at a loss as to what the problem is. Any help would be
>> appreciated.
>>
>> ...Bill Allen
>> ----- Original Message -----
>> From: "Creative Americas Customer Support"
>> @customercare.creative.com
>> To: "Bill Allen"
>> Sent: Monday, February 06, 2006 9:42 PM
>> Subject: Re: Creative System Information (English : Adobe Premeire Pro
>> .5
>> and Adobe Audition) (KMM933384I6636L0KM)
>>
>>
>> Dear Bill,
>>
>> Thank you for contacting Creative Technical Support.
>>
>> With regards to the issue you are having, I would really appreciate it
>> if you can provide me with the model number of the sound card. It
>> should
>> start with CT or SB followed by 4 numbers found on the sound card. I
>> also need the serial number which can be found on the sticker and the
>> ink stamp which is printed on the back of the card. This number will
>> not
>> be located on any of the stickers and it will not be labeled. It is a
>> number that has been stamped on the card itself, possibly near the
>> outer
>> edge of the card to determine the best advice for you.
>>
>> Did the sound card come pre-installed in the PC, comes in a plastic
>> cover or brown box or did it come in a Creative retail box package?
>>
>> Below is a link that may help with the location of the model number.
>>
>> Run a keyword search for SID2456 from the link below.
>>
Link removed
>>
>> I also need you to try the following recording test.
>>
>> SELECT THE RECORDING SOURCE IN SURROUND MIXER
>> . Go to Start Programs Creative SB Audigy Surround Mixer
>> 2. Click on the Recording Source (should be on the right side of the
>> mixer under the REC label)
>> 3. Change the recording source to Analog Mix
>> 4. Mute the other analog sources (Mic, CD Audio, Auxiliary, Tad, PC
>> speaker) that you don't want recorded with the audio stream.
>> 5. You may wish to select "record without monitoring" by click on the
>> (+) above the Analog Mix recording source. This keeps the source from
>> playing out to speakers while recording
>>
>> TEST RECORD THE AUDIO
>> . Go to Start Programs Accessories Multimedia Sound Recorder.
>> 2. Click the Record button (red dot)
>> 3. Talk into the microphone
>> 4. Let it record the source for a little bit
>> 5. Hit the Stop button (black square)
>> 6. Hit the play button (single arrow pointing right)
>> 7. You should now hear the audio that you recorded.
>>
>> If you are still having issues, I recommend you to ensure the
> following
>> for the audio installation and test:
>>
>> - The card is the only card installed other than the Graphics card.
>> - The card is at least one empty slot away from the Graphics card.
>> - Place the soundcard away from all the others.
>> - That the card is seated properly in the PCI slot.
>> - Move the PC's internal wires away from the soundcard.
>> - That the on-board sound on your motherboard is disabled through the
>> BIOS.
>> - That the on-board gameport is disabled through the BIOS.
>> - That your motherboard BIOS is up-to-date.
>> - That the operating system is up-to-date with the latest service
> packs
>> and patches.
>> - That there are no background applications open when you attempt the
>> solution.
>> - That the anti-virus program is disabled.
>> - That if you are over-clocking your system, return all options to
>> their
>> recommended settings.
>> - That you access the PC with administrator rights.
>>
>> Do reply back to me if you are still having problems with any error
>> messages prompted. Thanks.
>>
>> For faster service please reply with previous correspondence when
>> replying to this email.
>>
>> Best Regards
>> ,
>>
>> Ronshone
>> Technical Support
>> Creative Labs Americas
>>
>>
>>
>> To provide feedback on your "Creative Experience" please click on the
>> following link:
>>
Link removed
>>
>> This link is provided so that you may provide feedback on your
>> "Creative
>> Experience". If you require further troubleshooting or have additional
>> questions simply reply to the original mail and we will be glad to
>> assist you.
>>
>> Original Message Follows:
>> ------------------------
>> User Detail
>> ----------------------------------------
>> Name : Bill Allen
>> Email Address : [email protected]
>> Self Description : Intermediate PC User
>>
>> Creative Product Information
>> ----------------------------------------
>>
>> Problem Type : I need help with a third-party software application
>>
>> Problem lies with:
>> ----------------------------------------
>> Adobe Premeire Pro .5 and Adobe Audition
>>
>> Customer's System Specification
>> ----------------------------------------
>>
>>
>> Detailed Problem Description
>> ----------------------------------------
>> I can hear sound from my computers speakers. The diagnostic tests
>> performed by the Creative software are all "OK", but I cannot record
>> audio with either of the two programs mentioned above. I have checked
>> everything I can think of and all of the settings appear to be "OK".
> I
>> have also updated the driver for the sound card. What can I do?
>>
>> Attachment :
>> [ Attachment Type: application/octet-stream Name: CTSi.cab]

TeamRacing6 wrote:
b noir,
I can get itunes to start if I disable Bonjour or if I "repair" it first. Sometimes I can repair Bonjour though add/remove programs, sometimes it will only "repair" using WinRar. Sometimes I have to "repair" Bonjour 2 or 3 times to get iTunes to start.
I have tried uninstalling and reinstalling at least a dozen times. I have tried redownloading iTunes at least 5 times and from different links. This leads me to believe that the dnssd.dll file is not itself corrupt, but this newest version is causing a conflict with XP somewhere somehow.
Team, iTunes 10.2.2.12 has just been released. I installed it and checked, and BonJour's been updated to version 2.0.5.0, and there's a new 2.0.5.0 version of dnssd.dll on my system. So I reckon it's worth a try updating to that to see if it's of any help with your trouble.

HT5945 Why does Instal Java SE 6 keep popping up and when I attempt to install it says that there is a problem with the internet connection ??? Please help

I keep getting a pop up reminder to install Java SE 6. When I attempt to install it an error occurs saying that there is a internet connection problem and the Java cannot be intalled. This thing pops up every 15 minutes. Am I doing something wrong? Thanks for any help

OK, so you don't have a working iTunes.
What I would like to do now is to try installing each iTunes component separately.
First uninstall the 5 iTunes programs that you have installed.
You should have iTunesSetup.exe saved in a folder on your PC, probably in the downloads folder. If not download and save it now.
Open the folder containing iTunessetup.exe with explorer.
Next open notepad and copy the following 3 lines into it.
md temp
itunessetup /extract temp
pause
Save the file as extract.bat into the same folder that contains the itunes installer.
Open the downloads folder and you should find the extract file that you saved. Double click on it and a black window will open telling you what it is doing. When its finished, press any key to continue.
You should find that a folder called temp has been created containing all the itunes msi files.
Install in this order by double clicking on them:
Apple Application Support
Bonjour
Apple Mobile Device Support
Apple Software Update
Quicktime
iTunes
If one of the installs fails, stop and post the error message in full. I am hoping that by doing this separately we will get a better error message.

Help with Bluetooth internet using PBG4 and Nokia, please!

Similar Messages

Maybe you are looking for