Help with c877 DSL configuration

I have a C877 DSL router that I am trying to connect as a linknet so that I can run an igp on it to route my public ip's and private networks back through the DSL. Here is a bad ASCII drawing.
Cisco877 --------------- Lucent Stinger DSL ------------------ Cisco3750 L3 switch
| Aggregator |
DSL GigE interface Vlan 142
I have this working by using a BVI interface on the 877 DSL WAN (ATM0). See current configurations.
My problem is that I need to shape on the 877 as well as configure QOS (VoIP lives behind the 877) which from my understanding is not supported on BVI interfaces.
Is there some other way to set this up so that I can both shape and do QOS on the DSL?
Thanks!
-J

Hello J,
unfortunately given the need for IRB you cannot use another type of interface you should look for applying QoS tools on internal interface
you are using RFC1483 bridge mode
Hope to help
Giuseppe

Similar Messages

Looking for help with respect to configuring MS Exchange server to handle attachments over 10 MB for forwarding to Salesforce (Email-to-case).

Looking for help with respect to configuring MS Exchange server to handle attachments over 10 MB for forwarding to Salesforce (Email-to-case).
Problem - SFDC does not create cases from emails that have more than 10 MB of attachments. Our clients will not go-live if their clients cannot send in emails with attachments over 10 MBs
Potential resolution - Configure MS exchange to strip off the attachments(if over 10 MB) and store it in a public folder, forward the email to Salesforce (so the case gets created or the email
is associated to an existing case), the client should have some way to know if the attachments were stripped off and should be able to dlownload the attachments and continue with case resolution.
Any help is appreicated!
Thanks

Hi,
From your description, you want to achieve the following goal:
Configure Exchange to filter the attachments if the size is over 10 MB and store it in a public folder, and then forward the email to Salesforce.
Based on my knowledge, I'm afraid that it can't be achieved. Exchange can filter messages with attachments, but it couldn't store these attachments on public folder automatically. Also, I don't see any transport rule can do it.
Hope my clarification is helpful.
Best regards,
Amy Wang
TechNet Community Support

Help with Airport, DSL, PPPoE

Here is the deal: I have a DSL connection in my iMac with a DSL modem (Trendnet TDM-300) and PPPoE connection. The Internet works when I use a cable directly plugged to my iMac but when I create a Network (The imac is connected via Ethernet to the Airport and I use a PowerBook for Wireless) with my Airport Extreme, I can't connect to the internet althoght the Airport network is OK. It appears "Looking for PPPoE host...".
I recently upgraded the Airport Firmware to 5.7 and I'm using Tiger.
Any help??
PS: Sorry for my English, it's not my first languaje.
iMac G4, Flat-Panel Mac OS X (10.4.2)

I have made this work but it took some doing and my experience may be of some help to others.
Befor entering the world of PPPoE my set up was as follows.
Airport Extreme
connected wirelessly to a G4 powerbook
connected WAN to an ADSL modem
connected LAN to a hub and a desktop G4 and printers
all working fine
I purchase a "NOW" radio modem ( the modem connects using radio to a local cell) This uses PPPoE to make the connection to the internet. It is not the same as airport
In the end I used this procedure to get it working
1) Turn Airport off
2) Connect the radio modem to my laptop with an ethernet cable
3) Go to system preferences - network - Built in ethernet - AppleTalk and turn appletalk off
4) Go to PPPoE and turn it on and as a minimum enter you Account name and Password
5) Press the Apply Now button you should see activity on the LAN and WAN lights if you have them on your modem
6) In your web browser go to the internal page of the modem in my case 192.168.1.1 and set up the same user name and password. You may be able to confirm that this is accepted from within this page.
7) Either way confirm that you can access the internet from this computer only
8) Disconnect the ethernet cable from your computer and plug it into the WAN side of your Airport ( In my case I was replacing the ADSL lead with the Radio Modem lead)
9) On you computer turn "connect using PPPoE" off and turn Airport on
10) Lunch AirPort Admin Utility . app which is in Utilities select your base station and press the configure button enter password if necessary
11) In the Internet tab select connect using "PPP over Ethernet (PPPoE)" enter your (ISP)account name and press the change password button in this dialog enter your (ISP)password twice tick the Always stay connected and leave all the rest as they are
12) In the Network tab tick Distribute IP addresses and activate. Share a single IP address (using DHCP and NAT) If you are your own network and you do not care what your internal IP address is you can leave the rest of this page as it is. If it does mater to you I assume you use one of the options in the pop up. this is confusing as there is a lot of talk about using the router ie Airport as a bridge but you do not and you do issue IP addresses to your net work but not to the Modem.
13) Just about there now hit the update button and let the new settings update the Airport base station (router). At this stage you might have expected it to work but it did not for me
14) Quite AirPort Admin Utility . app and lunch the AirPort Setup Assistant.app
15) Select change settings on an existing AirPort Base Station make sure it is your base station and log in accept all the settings and on the last page update the base station.
This done I can connect to the internet from my laptop via airport from my desk top via ethernet, I can communicate between my two computer using appletalk and I can print to my ethernet printers.
Powerbook G4 Mac OS X (10.4.4)

Need help with Verizon DSL & Windows XP

Hello All,
I am personally running Verizon FIOS without any problems. However, my father-in-law still has Verizon DSL, which he has been using without any problems for the last 4 years until now.
To make the long story short, it seems that the LAN card that came with his old Dell PC died. I pulled it (there is no LAN NIC on the motherboard), and installed a new LAN card, which supports 10/100 MBps and is RoHS complient. However, for some unknown still to us reason, he is getting the LAN "Limited Connection" error.
I have tried everything I could think of, and spent over 6 hours with 3 different Verizon DSL tech support folks. However, we cannot even get to 192.168.1.1 (which is the address of the Westell 6100). I have tried even slowing the LAN card to 10 Mbps / Half-Duplex (or Full). TCP/IPv4 is set to obtain IP / DNS automatically and etc... It's also set to DHCP.
We know fo sure that his Verizon DSL connection does work. Why? Because when I plugged in the same Ethernet cable into a laptop that I brought with me, we had an instant Internet connection (running Windows 7).
So it must be something within Windows XP that is blocking access. I am trying to do everything to not having for him to buy a new computer at this time and save the current system.
I have deleted any and all Network cards drivers in the Control Panel / System / Devices. I have NOT messed with any registry tricks, but am now willing.
Any and all help with suggestions is greately appreciated.

Best guess is that you need a WindowsXP compatible driver for your new LAN card. You definitely need a driver, so if you "deleted any and all Network cards drivers" it isn't going to work. Go to the company website for the new LAN card and they should have a suitable driver.
There should not be any need to mess with the registry.

Videoconfrence : Help with MCU to configure in CCM

Hi,
I have a confusion with the configuration of the MCU in CallManager when i want to have a multipoint videoconference where 3 SCCP viedo endpoints(7985) and 1 Polycom video endpoint (H.323) participate all in the same confenrence!
Here is attached the architecture of my videoconference deseign.
I have activated SCCP and H.323 on the MCU.
I have added the MCU as a conference bridge in CCM, and configured MRGL to use this Conference Bridge.i associated the MRGL with the 3 video SCCP endpoint(7985) and now i can do Multipoint videoconference between the three video endpoints (7985)!!
The problem that i want to the Polycom participate and to initiate a videoconference with the other SCCP endpoints.
I have added a gatekeeper, i registered the MCU (H.323 activated) with the gatekeeper!! In CCM i added the gatekeeper and added a trunk Gatekeeper controlled!!
Now here is my problem: what else to do in CCM??
Should i create a route pattern that points to the trunk ??
or should i add the MCU as a H.323 gateway and a route pattern that points to the this H.323 gateway???
PLz help me, i really have a serious problem.
Thx

Hi,
i think that the most difficult part is done now.
plz can u tell me first of all if the bridge is registered with the callmanager?in the administration page of the CCM, click SERVICE >> MEDIA RESOURCE >> CONFERENCE BRIDGE.
Then u have to find your bridge configured (u should see it's IP address).
If this is done, so u need to configure a service (SCCP activated)in the MCU.
U need to login to ur mcu with a browser, then click SERVICES >> ADD , and u need to activate the SCCP field, then choose ur video and audio parameters.
If this is done so to start a videoconference(between 3 persons for example) all u have to do is :
If u have 3 persons : A,B and C (and u'r the person A)
so A calls B normally, here a point to point videocall should be established (done by the CCM), then to make multipoint videoconference, u shoud click on the button MORE of ur phone, u'll see the word CONF, click CONF, u enter the number of the third person and when he hangs on the phone u click an other once on CONF. then a Multipoint videoconference should be established using the bridge this once.
unfortunately i can't have picture of my configuration because i did it in a production in another entreprise but u the online course (ICRMC) an e-learning course, had helped me a lot an there is flash videos that can give u an idea:
http://www.cisco.com/web/learning/le36/learning_partner_e-learning_connection_tool_launch.html
i hope this helps,
If there is an other problem plz contact me.

Help with Class-map configuration - ZBFW

Hello,
I need some clarification regarding the class-map configuration in a ZBFW. I need to allow https,http,ftp & rdp traffic from Internet to few of the servers inside our LAN. So I put the below configuration to accomplish the task (example shows class-map for only https protocol) :
a.)
class-map type inspect match-all HTTPS-ACCESS
match protocol https
match access-group name HTTPS-SERVER-ACCESS
ip access-list extended HTTPS-SERVER-ACCESS
permit tcp any host 172.17.0.55 eq 443
permit tcp any host 172.17.0.56 eq 443
permit tcp any host 172.17.0.36 eq 443
permit tcp any host 172.17.0.45 eq 443
permit tcp any host 172.17.0.60 eq 443
Where 55,56,36,45,60 are the servers inside the LAN (12 more servers are there) that need to be accessed via https,http,ftp & rdp from Internet.
Is it a correct approach? or do I need to change my configuation so that I have to match ACL with my class-map like below:
b.)
ip access-list extended OUTSIDE-TO-INSIDE-ACL
permit tcp any host 172.17.0.55 eq 443
permit tcp any host 172.17.0.55 eq www
permit tcp any host 172.17.0.55 eq 21
permit tcp any host 172.17.0.55 eq 3389
permit tcp any host 172.17.0.56 eq 443
permit tcp any host 172.17.0.56 eq www
permit tcp any host 172.17.0.56 eq 21
permit tcp any host 172.17.0.56 eq 3389
permit tcp any host 172.17.0.36 eq 443
permit tcp any host 172.17.0.36 eq www
permit tcp any host 172.17.0.36 eq 21
permit tcp any host 172.17.0.36 eq 3389
permit tcp any host 172.17.0.45 eq 443
permit tcp any host 172.17.0.45 eq www
permit tcp any host 172.17.0.45 eq 21
permit tcp any host 172.17.0.45 eq 3389
class-map type inspect match-all OUT-IN-CLASS
match access-group name OUTSIDE-TO-INSIDE-ACL
Which one is the correct approach when we consider the performance of the firewall ? Please help me.
Regards,
Yadhu

Hey
I do not agree with Varun, I think the first approach is the best one.
Why? Because when you issue the "match protocol ..." you are usig NBAR wich is an application inspection software, which means that https or whatever protocol is inspected at layer 7, not layer 3 and 4 which the seconds approach does (IP and port-number).
Lets say you use the second approach and an attacker uses some malicious protocol that runs over port 443 or whatever (a port that you opened). That attack would be successfull because all you say, you are going to IP-address 172.17.0.56 over port 443 so go ahead.
But if you are using NBAR, this would not work because NBAR will look at layer 7, inside the protocol itself and look if this really is HTTPS (or whatever protocol).
That's my two cents. Hope it helped!

Newbie help with Fixed IP configuration / Machine Record

I have a Mac Mini running Snow Leopard Server. It has a fixed IP, and runs a variety of web services, iCal Server and Address Book Server. I've been having problems getting VPN to work (can connect from client OK, but not able to get any traffic through the VPN subsequently).
In the process of trying to work out what is wrong with VPN, I noticed an oddity with the 'machine record' in DNS. The server was configured initially while connected to a LAN, but now runs with a fixed IP / FQDN outside the LAN.
DNS is set up with the original machine name (sls.2gc.org) assigned to the original 192.x.x.x address it had when first configured. The reverse entry is also based on this 192. number.
This name and 192.x.x.x number also appears in the 'Workgroup Manager' in the machine record.
The new configuration has the machine assigned to a FQDN that is not the same as the original machine name (2gc.org, rather than sls.2gc.org), and a different IP address (77.44.50.51).
Question is do I need to do anything (does the mapping to 192.x.x.x matter). If so, do I simply run changeip to correct the number / name, or do I have to also manually change the Workgroup Manager and DNS entries too?
Thanks in advance for any help.

You need a second IP for the server which you can use to get at services in the server itself.
If you try to use the main IP, even when the VPN is up, the traffic will not go through the VPN but direct and will then be stopped by the firewall.
From what IP-range does the VPN client get it's IP?
If you need to go through the VPN and then to Internet (via the server) you need to have NAT running.
NAT requires the firewall running and you'd also need ipforwarding (automatically on when firewall/NAT is on).
The server can have a second (private) IP added to an alias en0 ethernet interface.
I'd prefer using a NAT router/firewall between server and Internet or a second (LAN) interface in the server. Some use Apple USB -> ethernet adapter but you also have the AirPort one (but it won't make a good AP and you only get WEP encryption).

Need help with cisco 881 configuration.

Hi, I have cisco 881 wireless router, and I need to configure this as a switch, I have dhcp server in network 192.168.12.254, and I need that cisco wifi and lan clients get IP addresses from existing dhcp server.
I connect wire from network (with dhcp server) to FastEthernet0, create vlan interface (192.168.12.10 255.255.255.0), described vlan on other FastEthernet interfaces, so LAN clients get IP addresses from my dhcp server without problems, but how to do the same with wifi clients?

Follow this support doc because you need to trunk the AP to the router and specify the vlan the wireelss clients will be on.
https://supportforums.cisco.com/docs/DOC-16145
Here is a doc that guides you through multiple vlans/subnets on access points:
https://supportforums.cisco.com/docs/DOC-14496
Thanks,
Scott
Help out other by using the rating system and marking answered questions as "Answered"

Help with QoS basic configuration.

Hi all, i want to configure qos in a cisco lan with non cisco phone. I read a lot of documentation and some basic videos. I don't want to configure it very granular, so, the most basic commands that i found:
conf t
int fa0/5
switchport voice vlan 111
mls qos trust cos
auto qos voip trust
How i'm be realy sure that QoS is working on mi lan?
And how about the interface trunk configuration?
Any suggestion?
Here are the verification:
In the show running-configuration :
mls qos map cos-dscp 0 8 16 24 32 46 48 56
mls qos srr-queue input bandwidth 70 30
mls qos srr-queue input threshold 1 80 90
mls qos srr-queue input priority-queue 2 bandwidth 30
mls qos srr-queue input cos-map queue 1 threshold 2 3
mls qos srr-queue input cos-map queue 1 threshold 3 6 7
mls qos srr-queue input cos-map queue 2 threshold 1 4
mls qos srr-queue input dscp-map queue 1 threshold 2 24
mls qos srr-queue input dscp-map queue 1 threshold 3 48 49 50 51 52 53 54 55
mls qos srr-queue input dscp-map queue 1 threshold 3 56 57 58 59 60 61 62 63
mls qos srr-queue input dscp-map queue 2 threshold 3 32 33 40 41 42 43 44 45
mls qos srr-queue input dscp-map queue 2 threshold 3 46 47
mls qos srr-queue output cos-map queue 1 threshold 3 4 5
mls qos srr-queue output cos-map queue 2 threshold 1 2
mls qos srr-queue output cos-map queue 2 threshold 2 3
mls qos srr-queue output cos-map queue 2 threshold 3 6 7
mls qos srr-queue output cos-map queue 3 threshold 3 0
mls qos srr-queue output cos-map queue 4 threshold 3 1
mls qos srr-queue output dscp-map queue 1 threshold 3 32 33 40 41 42 43 44 45
mls qos srr-queue output dscp-map queue 1 threshold 3 46 47
mls qos srr-queue output dscp-map queue 2 threshold 1 16 17 18 19 20 21 22 23
mls qos srr-queue output dscp-map queue 2 threshold 1 26 27 28 29 30 31 34 35
mls qos srr-queue output dscp-map queue 2 threshold 1 36 37 38 39
mls qos srr-queue output dscp-map queue 2 threshold 2 24
mls qos srr-queue output dscp-map queue 2 threshold 3 48 49 50 51 52 53 54 55
mls qos srr-queue output dscp-map queue 2 threshold 3 56 57 58 59 60 61 62 63
mls qos srr-queue output dscp-map queue 3 threshold 3 0 1 2 3 4 5 6 7
mls qos srr-queue output dscp-map queue 4 threshold 1 8 9 11 13 15
mls qos srr-queue output dscp-map queue 4 threshold 2 10 12 14
mls qos queue-set output 1 threshold 1 100 100 50 200
mls qos queue-set output 1 threshold 2 125 125 100 400
mls qos queue-set output 1 threshold 3 100 100 100 400
mls qos queue-set output 1 threshold 4 60 150 50 200
mls qos queue-set output 1 buffers 15 25 40 20
mls qos
In the interface configuration:
interface FastEthernet0/5
switchport access vlan 111
switchport mode access
switchport voice vlan 111
srr-queue bandwidth share 1 30 35 5
priority-queue out
mls qos trust cos
auto qos trust
spanning-tree portfast
In trunk port:
interface GigabitEthernet0/1
switchport mode trunk
sh mls qos int f0/5
FastEthernet0/5
trust state: trust cos
trust mode: trust cos
trust enabled flag: ena
COS override: dis
default COS: 0
DSCP Mutation Map: Default DSCP Mutation Map
Trust device: none
qos mode: port-based
Thanks a lot !
Martín.

Hi, thanks for reply. I investigate a little more.
When i want verify that QoS really work in the lan, first of all:
- The marking (in my case verify traffic VoIP at 64)
- Queue, that put first in the queue voice traffic, dscp 64
To try, i make a call connecting an IP phone (in fa0/6) and call to analog phone. Wait for 2 minutes and see what changes in this command:
Switch#sh mls qos int f0/6 stFastEthernet0/6 (All statistics are in packets) dscp: incoming------------------------------- 0 - 4 : 4465744658 0 0 0 0 5 - 9 : 0 0 0 0 0 10 - 14 : 0 0 0 0 0 15 - 19 : 0 0 0 0 0 20 - 24 : 0 0 0 0 0 25 - 29 : 0 1196 0 0 0 30 - 34 : 0 0 0 0 0 35 - 39 : 0 0 0 0 0 40 - 44 : 0 0 0 0 0 45 - 49 : 0 41769 62163 0 91 98 0 50 - 54 : 0 0 0 0 0 55 - 59 : 0 0 0 0 0 60 - 64 : 0 0 0 0 dscp: outgoing------------------------------- 0 - 4 : 251670 272323 0 0 0 0 5 - 9 : 0 0 0 0 0 10 - 14 : 0 0 0 0 0 15 - 19 : 0 0 0 0 0 20 - 24 : 0 0 0 0 0 25 - 29 : 0 0 0 0 0 30 - 34 : 0 0 0 0 0 35 - 39 : 0 0 0 0 0 40 - 44 : 0 0 0 0 0 45 - 49 : 0 3393 0 0 0 50 - 54 : 0 0 0 0 0 55 - 59 : 0 0 0 0 0 60 - 64 : 0 0 0 0 cos: incoming------------------------------- 0 - 4 : 89094 109541 0 0 0 0 5 - 7 : 0 0 0 cos: outgoing------------------------------- 0 - 4 : 295699 316387 0 0 0 0 5 - 7 : 3393 0 0 output queues enqueued: queue: threshold1 threshold2 threshold3----------------------------------------------- queue 0: 2 0 0 queue 1: 209108 1534 194272 queue 2: 0 0 56565 queue 3: 0 0 33762 output queues dropped: queue: threshold1 threshold2 threshold3----------------------------------------------- queue 0: 0 0 0 queue 1: 57 0 0 queue 2: 0 0 0 queue 3: 0 0 0Policer: Inprofile: 0 OutofProfile: 0
The underlined numbers is the variations in aprox. 2 minutes in the call. That mean that the traffic was marked as VoIP traffic, but i´m not sure that the traffic is queued right.
I´m wrong?
Thanks for the help
PS:Later monitoring: with iperf or Cacti using IP SLA.

Help with VPN (DSL/PPoE)

Here is my network:
Speedstream 4200 Modem (DSL over PPoE) -> Cisco RV220w
I have created a QuickVPN client on the RV220w but when I use the public facing IP address and try to connect using these credentials, I just get a 'remote host cannot be reached' type of error. Is anyone familiar with the Speedstream 4200 modem? Do I need to change it to BRIDGE mode or change something so that it'll work with the RV220?

The modem is now in BRIDGE mode so the RV220w now has the public IP. I've followed the router admin guide to add a QuickVPN client and used the QuickVPN client software on an XP machine outside of the network to try and connect. I get the usual "failed to establish a connection" error message. And yes, I've disabled the Windows firewall on this machine.
I really need someone to hand hold me to get this set up, or at least point me to some pretty detailed walkthroughs online.
Can anyone help?

Help with a Blind Configuration of a G5 Cluster node

So I bought 2 G5 Cluster Nodes to dedicate some audiovisual processes to them. My only other mac computer is a Core 2 Duo Macbook Pro.
Using Pacifist, I was able to do a clean install of Mac OSX onto the internal drive by putting it into an external enclosure.
Now here is my problem: The cluster nodes have no videocard.
I plan on using them through the OSX Screen Sharing function, when they will be conencted to the network, but I don't know how to do the initial configuration of Mac OS X on them, since I can not boot from a system using the Apple Partition Map on my Macbook pro, and the Cluster node will not boot from the GIUD partition scheme.
Can anyone please help me?
Thanks,
Chuck

Assuming you're running Mac OS X Server on the cluster node, just boot the server normally - it will run a special first-time-boot process that sets up a network listener.
You can then install the Server Admin tools on your MacBook Pro and run Server Assistant. Server Assistant will look out over the network and find the new servers, then give you the opportunity to configure them remotely (assign account data, IP address, etc.).
(note you can also do this as part of the initial install process - boot the server from the Install DVD and run the entire OS installation and configuration remotely via Server Assistant)
Note: If you're not running Mac OS X Server on the cluster nodes then the above doesn't apply

Help with a simple configuration to connect a pc and router

Since I want to access to my openwrt router at my network's home I discovered I am forced to use OpenVPN. In fact the ISP which provides the internet connection doesn't allow his customers to be visible from the exterior (it is an Italian ISP named Fastweb).
The pc with what I want to access my router from the exterior is connected to the internet with a public IP and I can open the doors I want. For this reason I want to install the openvpn server on that pc.
What I would like to achieve is to see all the devices connected on the openwrt router (and the router itself) from the PC with the public IP.
For example, access the router web interface by simply writing 192.168.1.1 on the pc with openvpn server of which the local address is 10.0.0.2.
At the same time I would avoid to install the openvpn client on each device connected to the openwrt router. Is this possible? So reach the 192.168.1.3 pc from my openvpn server pc with 10.0.0.2 as local address, without installing openvpn client on the 192.168.1.3 pc.
Is this kind of operation called "bridging"? I am pretty new with openvpn, so I came here to gently ask if you can suggest me some configurations for the openvpn server and client.
What would happen if I restart the pc with the openvpn server? I mean does the router with openvpn client automatically reconnect as soon the openvpn server is again on?
I think an image is better descriptive of what I want to build:
Really thanks in advance.
Last edited by Garret (2011-12-14 00:53:28)

EDIT: AFAIK, the concept of "Server" and "Client" in OpenVPN only refers to which machine initiates the connection. It doesn't affect the resulting connection. That is entirely dependent on the configuration.
Garret wrote:At the same time I would avoid to install the openvpn client on each device connected to the openwrt router. Is this possible? So reach the 192.168.1.3 pc from my openvpn server pc with 10.0.0.2 as local address, without installing openvpn client on the 192.168.1.3 pc.
You only need the Client on one machine.
Garret wrote:Is this kind of operation called "bridging"? I am pretty new with openvpn, so I came here to gently ask if you can suggest me some configurations for the openvpn server and client.
If you setup a bridged VPN, the "OpenVPN Server" machine will get a second address within the 192.168.1.x network (for example, 192.168.1.20). It will use this address (via the VPN) to connect to the other hosts inside your network.
If you setup a routed VPN, then both address ranges (192.168.1.x and 10.0.0.x) will "become visible" at both ends.
If you only want the "OpenVPN Server" to be able to access your "home", then I would recommend a Bridged VPN.
Garret wrote:What would happen if I restart the pc with the openvpn server? I mean does the router with openvpn client automatically reconnect as soon the openvpn server is again on?
Yes.
Last edited by fukawi2 (2011-12-13 22:38:58)

Help with USB device configuration

Hi, LabVIEW 2009, Windows 7, x86
1. I have just connected a USB Hanna HI3221 pH meter to the computer above.
2. The device shows up in the Windows Control Panel as working properly and identified as an HI3221.
3. I rebooted the computer, logged in again etc.
4. I start the "NI Device Monitor".
5. I plug in the USB Device and unfortunately as described on page 3 here
http://digital.ni.com/manuals.nsf/websearch/231F4BE79F2F7CB58625758300711E6E
I do not get prompted to begin a measurement with the device, to begin an application with the device, etc.
I don't see the device in MAX either.
Although I can browse other connected USB devices as VISA resources in LabVIEW, eg. a USB Agilent U2355a as "USB0::2391::4888::TW48052027::0::INSTR", I cannot see this USB device.
Can anyone throw any light as to how I can configure up this device?
Thanks in advance
Mike

Hi mike
Max is developed for NI hard ware and hence the
drivers are primarily designed for NI products. As the hard ware is third party
it is possible to create a driver using the VISA Driver Development Wizard .
Once created search for the device in MAX .
See the link posted below for a tutorial on USB
control.
http://zone.ni.com/devzone/cda/tut/p/id/4478
Robert
Regards
Robert
National Instruments UK & Ireland

Help with using xmonad configuration

http://haskell.org/haskellwiki/Xmonad/C … _xmonad.hs
ok when I did ghci <filename> after I downloaded the configuration, I got an error saying parse error on input `<!' Failed modules loaded: none.
how would I go about solving this problem?
PS I'm a noob when it comes to this stuff but I'm learning
Last edited by unregistered (2009-06-08 10:15:41)

Here is Assorato's config:
{-# OPTIONS_GHC -fglasgow-exts -fno-warn-missing-signatures #-}
-- |
-- Module : XMonad.Config.Arossato
-- Copyright : (c) Andrea Rossato 2007
-- License : BSD3-style (see LICENSE)
-- Maintainer : [email protected]
-- Stability : stable
-- Portability : portable
-- This module specifies my xmonad defaults.
module XMonad.Config.Arossato
( -- * Usage
-- $usage
arossatoConfig
) where
import qualified Data.Map as M
import XMonad hiding ( (|||) )
import qualified XMonad.StackSet as W
import XMonad.Actions.CycleWS
import XMonad.Hooks.DynamicLog hiding (xmobar)
import XMonad.Hooks.ManageDocks
import XMonad.Hooks.ServerMode
import XMonad.Layout.Accordion
import XMonad.Layout.LayoutCombinators
import XMonad.Layout.Magnifier
import XMonad.Layout.NoBorders
import XMonad.Layout.SimpleFloat
import XMonad.Layout.Tabbed
import XMonad.Layout.WindowArranger
import XMonad.Prompt
import XMonad.Prompt.Shell
import XMonad.Prompt.Ssh
import XMonad.Prompt.Theme
import XMonad.Prompt.Window
import XMonad.Prompt.XMonad
import XMonad.Util.Run
import XMonad.Util.Themes
-- $usage
-- The simplest way to use this configuration module is to use an
-- @~\/.xmonad\/xmonad.hs@ like this:
-- > module Main (main) where
-- >
-- > import XMonad
-- > import XMonad.Config.Arossato (arossatoConfig)
-- >
-- > main :: IO ()
-- > main = xmonad =<< arossatoConfig
-- NOTE: that I'm using xmobar and, if you don't have xmobar in your
-- PATH, this configuration will produce an error and xmonad will not
-- start. If you don't want to install xmobar get rid of this line at
-- the beginning of 'arossatoConfig'.
-- You can use this module also as a starting point for writing your
-- own configuration module from scratch. Save it as your
-- @~\/.xmonad\/xmonad.hs@ and:
-- 1. Change the module name from
-- > module XMonad.Config.Arossato
-- > ( -- * Usage
-- > -- $usage
-- > arossatoConfig
-- > ) where
-- to
-- > module Main where
-- 2. Add a line like:
-- > main = xmonad =<< arossatoConfig
-- 3. Start playing with the configuration options...;)
arossatoConfig = do
xmobar <- spawnPipe "xmobar" -- REMOVE this line if you do not have xmobar installed!
return $ defaultConfig
{ workspaces = ["home","var","dev","mail","web","doc"] ++
map show [7 .. 9 :: Int]
, logHook = myDynLog xmobar -- REMOVE this line if you do not have xmobar installed!
, manageHook = newManageHook
, layoutHook = avoidStruts $
decorated |||
noBorders mytabs |||
otherLays
, terminal = "urxvt +sb"
, normalBorderColor = "white"
, focusedBorderColor = "black"
, keys = newKeys
, handleEventHook = serverModeEventHook
, focusFollowsMouse = False
where
-- layouts
mytabs = tabbed shrinkText (theme smallClean)
decorated = simpleFloat' shrinkText (theme smallClean)
tiled = Tall 1 (3/100) (1/2)
otherLays = windowArrange $
magnifier tiled |||
noBorders Full |||
Mirror tiled |||
Accordion
-- manageHook
myManageHook = composeAll [ resource =? "win" --> doF (W.shift "doc") -- xpdf
, resource =? "firefox-bin" --> doF (W.shift "web")
newManageHook = myManageHook
-- xmobar
myDynLog h = dynamicLogWithPP defaultPP
{ ppCurrent = xmobarColor "yellow" "" . wrap "[" "]"
, ppTitle = xmobarColor "green" "" . shorten 40
, ppVisible = wrap "(" ")"
, ppOutput = hPutStrLn h
-- key bindings stuff
defKeys = keys defaultConfig
delKeys x = foldr M.delete (defKeys x) (toRemove x)
newKeys x = foldr (uncurry M.insert) (delKeys x) (toAdd x)
-- remove some of the default key bindings
toRemove x =
[ (modMask x , xK_j)
, (modMask x , xK_k)
, (modMask x , xK_p)
, (modMask x .|. shiftMask, xK_p)
, (modMask x .|. shiftMask, xK_q)
, (modMask x , xK_q)
] ++
-- I want modMask .|. shiftMask 1-9 to be free!
[(shiftMask .|. modMask x, k) | k <- [xK_1 .. xK_9]]
-- These are my personal key bindings
toAdd x =
[ ((modMask x , xK_F12 ), xmonadPrompt defaultXPConfig )
, ((modMask x , xK_F3 ), shellPrompt defaultXPConfig )
, ((modMask x , xK_F4 ), sshPrompt defaultXPConfig )
, ((modMask x , xK_F5 ), themePrompt defaultXPConfig )
, ((modMask x , xK_F6 ), windowPromptGoto defaultXPConfig )
, ((modMask x , xK_F7 ), windowPromptBring defaultXPConfig )
, ((modMask x , xK_comma ), prevWS )
, ((modMask x , xK_period), nextWS )
, ((modMask x , xK_Right ), windows W.focusDown )
, ((modMask x , xK_Left ), windows W.focusUp )
-- other stuff: launch some useful utilities
, ((modMask x , xK_F2 ), spawn "urxvt -fg white -bg black +sb" )
, ((modMask x .|. shiftMask, xK_F4 ), spawn "~/bin/dict.sh" )
, ((modMask x .|. shiftMask, xK_F5 ), spawn "~/bin/urlOpen.sh" )
, ((modMask x .|. shiftMask, xK_t ), spawn "~/bin/teaTime.sh" )
, ((modMask x , xK_c ), kill )
, ((modMask x .|. shiftMask, xK_comma ), sendMessage (IncMasterN 1 ) )
, ((modMask x .|. shiftMask, xK_period), sendMessage (IncMasterN (-1)) )
-- commands fo the Magnifier layout
, ((modMask x .|. controlMask , xK_plus ), sendMessage MagnifyMore)
, ((modMask x .|. controlMask , xK_minus), sendMessage MagnifyLess)
, ((modMask x .|. controlMask , xK_o ), sendMessage ToggleOff )
, ((modMask x .|. controlMask .|. shiftMask, xK_o ), sendMessage ToggleOn )
-- windowArranger
, ((modMask x .|. controlMask , xK_a ), sendMessage Arrange )
, ((modMask x .|. controlMask .|. shiftMask, xK_a ), sendMessage DeArrange )
, ((modMask x .|. controlMask , xK_Left ), sendMessage (DecreaseLeft 10))
, ((modMask x .|. controlMask , xK_Up ), sendMessage (DecreaseUp 10))
, ((modMask x .|. controlMask , xK_Right), sendMessage (IncreaseRight 10))
, ((modMask x .|. controlMask , xK_Down ), sendMessage (IncreaseDown 10))
, ((modMask x .|. shiftMask , xK_Left ), sendMessage (MoveLeft 10))
, ((modMask x .|. shiftMask , xK_Right), sendMessage (MoveRight 10))
, ((modMask x .|. shiftMask , xK_Down ), sendMessage (MoveDown 10))
, ((modMask x .|. shiftMask , xK_Up ), sendMessage (MoveUp 10))
-- gaps
, ((modMask x , xK_b ), sendMessage ToggleStruts )
] ++
-- Use modMask .|. shiftMask .|. controlMask 1-9 instead
[( (m .|. modMask x, k), windows $ f i)
| (i, k) <- zip (workspaces x) [xK_1 .. xK_9]
, (f, m) <- [(W.greedyView, 0), (W.shift, shiftMask .|. controlMask)]
As you can see Assorato uses other keybindings than the default ones.

Help with private line configuration

hey,
scenario is i have ccme running at present. we have 2 T1 CAS e&m interfaces working. at present i have COR configured to allow private line users to use those lines and no one else. what i wanted to find out was if it were possible, with my configuration, to associate the private line port, directly with the direct line button, meaning, if he/she presses the direct line button, it will off-hook the port automatically.
issue is that i have an integration with a PBX along the the CME and the COR configured does not apply to the remote end router. therefore, when the lines get saturated (everyone uses the 2t1 on ccme for inbound and outbound), ppl on the pbx end has the ability to use the private line to make outgoing calls.
any ideas will be greatly appreciated. as i have configured a temp solution where the private line users, press 1 then thier number to make the call. its temporary, since the private lines are associated with managers, and they want total transparency therefore, removing the 1.

any ideas welcome

Help with c877 DSL configuration

Similar Messages

Maybe you are looking for