Help with Cisco 5508 management interface

Hello,
I'm trying to verify some behaviors I'm seeing with my 5508 controller setup and forgive me for missing anything obvious, I've zero experience with this hardware and clueless on the best practices. With that said... out of the box I ran through the AutoInstall process.
I gave my service port an IP address on my subnet, 10.10.8.0/24 vlan 100 and gave the management interface the ip address 10.10.30.5/24 vlan 130
From my host I can ping the management interace 10.10.30.5 and the interface gateway 10.10.30.1
I cannot connect to the controller via 10.10.30.5 either through the web GUI or telnet
I can connect to the controller via 10.10.8.200 both through the web interface and telnet
while connected to the service port, I can ping the management port IP but I cannot ping the 10.10.30.1 gateway.
We have attached two test 3502I AP's and they found the controller and pulled correct ip addresses, clients can authenticate and access network resources as well as the Internet so for the most part, things are working but it concerns me that the management interface can't ping its own gateway.
Keep in mind, I did no other configurations besides what got configured in the AutoInstall process. What should I look at to resolve?
Thanks!
Mike

The service port is for out of band management and should not be connected to the network. If connected tot he network, it should not have connectivity to the management interface of the wlc.
You can create an ACL to block the service port ip to the managment vlan if you want. I normally do not connect the service port to the network.

Similar Messages

Need help with Cisco Interface Cards???/

Hi, I purchased 4 WIC-1AM cards for my cisco 1760 gateway to use with cisco call manager server. I'm trying to figure out if I can even use these cards for voice cards to make calls inbound and outbound. I'm seing that the cards that CM gives me are all VIC cards listed and i don't see any WIC cards listed in the endpoint list on the CM for the gatway. So can I even use these cards for what I'm trying to do??? Please help???
Thanks

If i got the vontage sip account how would i hook it up to my CM Sever?
I'm using a 1760 gatway, what is a DSP resource?
When i do show diag I get this from my router:
show diag
Slot 0:
C1760 1FE VE 4SLOT DV Mainboard Port adapter, 3 ports
Port adapter is analyzed
Port adapter insertion time unknown
EEPROM contents at hardware discovery:
Hardware Revision : 5.0
PCB Serial Number : FOC08077JDP
Part Number : 73-7167-05
Board Revision : B0
Fab Version : 04
Product (FRU) Number : CISCO1760
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF 40 03 16 41 05 00 C1 8B 46 4F 43 30 38 30
0x10: 37 37 4A 44 50 82 49 1B FF 05 42 42 30 02 04 FF
0x20: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x30: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x40: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
Packet Voice DSP Module Slot 0:
Not populated
Packet Voice DSP Module Slot 1:
Not populated
WIC/VIC Slot 0:
One Port Modem WIC
Hardware revision 1.0 Board revision H0
Serial number 0034764142 Part number 800-08823-01
FRU Part Number WIC-1AM=
Test history 0x00 RMA number 00-00-00
Connector type WAN Module
EEPROM format version 1
EEPROM contents (hex):
0x20: 01 38 01 00 02 12 75 6E 50 22 77 01 00 00 00 00
0x30: 88 00 00 00 06 02 10 01 FF FF FF FF FF FF FF FF
WIC/VIC Slot 1:
One Port Modem WIC
Hardware revision 1.0 Board revision H0
Serial number 0034764050 Part number 800-08823-01
FRU Part Number WIC-1AM=
Test history 0x00 RMA number 00-00-00
Connector type WAN Module
EEPROM format version 1
EEPROM contents (hex):
0x20: 01 38 01 00 02 12 75 12 50 22 77 01 00 00 00 00
0x30: 88 00 00 00 06 02 10 01 FF FF FF FF FF FF FF FF
What do you think?

WLC 5508 management interface

Hi, I have a particular wireless design that requires one WLC 5508 to be connected to two seperate swithces. Port 1 of WLC is connected trunk to Switch A and Port 2 of WLC is connected to Switch B. Each switch has its own local VLANS. When I connect 1130s LAPs they need to find the management interface initially and then use only AP management interfaces. since there is only one management interface, if I assign management interface on a vlan that is configured on switch A then APs on switch A join fine but those on switch B keep asking for management interface and from capwap debug on WLC it says that join request was received on wrong ineterface ....
the only work around to this was to make routing between switch A and switch B for the two vlans on which APs reside... but for security purposes - client would like to avoid this
any help much appreciated ..

Hi thanks for your reply,
Yes I agree perfectly with your explanation - On both switches I have UDP forward for 5246 and 5247 and everything works fine.
You understood exactly what's happening for initial discovery the Guest AP asks for managemnt interface through WLC port 2 but managerment IP is on admin side WLC port 1 and then it drops packet saying that it was received on the wrong port. In fact that is why I put an ACL between the Admin switch and guest switch taht allows only 5426 capwap control - just to allow that initial discovery from guest AP to contact Management interface which can only be assigned to one port and in my case it is on the admin switch side. And that is why I had to make a route between the two independent switches.
My question is to know if there is any other way with my given design to eliminate this initial discovery to the management inetrface, as my client would like the admin and guest switches to be completely seperated i.e. without the routing. Is there any way that the guest APs can make contact with the AP management interface on their side only skipping the discovery of the management interface ? the guest APs were primed on the admin side so they know the IP. After the initial discovery, if I remove the routing between admin and guest switch, guest APs keep their connectivity without any problems.

IPS Tech Tips: IPS Best Practices with Cisco Remote Management Services

Hi Folks -
Another IPS Tech Tip coming up and this time we will be hearing from some past and current Cisco Remote Services members on their best practice suggestions. As always these are about 30 minutes of content and then Q&A - a low cost high reward event.
Hope to see you there.
-Robert
Cisco invites you to attend a 30-45 minute Web seminar on IPS Best   Practices delivered via WebEx. This event requires registration.
Topic: Cisco IPS Tech Tips - IPS Best Practices with Cisco Remote Management   Services
Host: Robert Albach
Date and Time:
Wednesday, October 10, 2012 10:00 am, Central Daylight Time (Chicago,   GMT-05:00)
To register for the online event
1. Go to https://cisco.webex.com/ciscosales/onstage/g.php?d=203590900&t=a&EA=ralbach%40cisco.com&ET=28f4bc362d7a05aac60acf105143e2bb&ETR=fdb3148ab8c8762602ea8ded5f2e6300&RT=MiM3&p
2. Click "Register".
3. On the registration form, enter your information and then click   "Submit".
Once the host approves your registration, you will receive a confirmation   email message with instructions on how to join the event.
For assistance
http://www.webex.com
IMPORTANT NOTICE: This WebEx service includes a feature that allows audio and   any documents and other materials exchanged or viewed during the session to   be recorded. By joining this session, you automatically consent to such   recordings. If you do not consent to the recording, discuss your concerns   with the meeting host prior to the start of the recording or do not join the   session. Please note that any such recordings may be subject to discovery in   the event of litigation. If you wish to be excluded from these invitations   then please let me know!

Hi Marvin, thanks for the quick reply.
It appears that we don't have Anyconnect Essentials.
Licensed features for this platform:
Maximum Physical Interfaces       : Unlimited      perpetual
Maximum VLANs                     : 100            perpetual
Inside Hosts                      : Unlimited      perpetual
Failover                          : Active/Active perpetual
VPN-DES                           : Enabled        perpetual
VPN-3DES-AES                      : Enabled        perpetual
Security Contexts                 : 2              perpetual
GTP/GPRS                          : Disabled       perpetual
AnyConnect Premium Peers          : 2              perpetual
AnyConnect Essentials             : Disabled       perpetual
Other VPN Peers                   : 250            perpetual
Total VPN Peers                   : 250            perpetual
Shared License                    : Disabled       perpetual
AnyConnect for Mobile             : Disabled       perpetual
AnyConnect for Cisco VPN Phone    : Disabled       perpetual
Advanced Endpoint Assessment      : Disabled       perpetual
UC Phone Proxy Sessions           : 2              perpetual
Total UC Proxy Sessions           : 2              perpetual
Botnet Traffic Filter             : Disabled       perpetual
Intercompany Media Engine         : Disabled       perpetual
This platform has an ASA 5510 Security Plus license.
So then what does this mean for us VPN-wise? Is there any way we can set up multiple VPNs with this license?

Is it possible to integrate Nokia E62 with Cisco Call Manager 4.x?

The Nokia E-61 can be integrated with Cisco Call manager 4.x using a Nokia Call Connect 1.0 client.
1.Is it possible to do the same with Nokia E62.If it can be done,what would be the requirements?
2.Is Nokia E-62 PDA a Cisco Compatible Extension device?

Thanks a lot for the prompt reply.You are right in saying that nokia and cisco are increasing the number of models supported.Infact the E65 has already joined the club.But my point of interest is the nokia E62 in particular.This Nokia E62 device
1) does not support WLAN interface(while E61,E65 does).
2) It is not Cisco Commpatible extension device.(I did not find E62 in the list of Cisco Compatible extensions.chk out the attachments for more info).
3)It is not compatible with Nokia Intellisync CAll Connect 1.0(while E61 and E65 are compatible.chk out the attachment for more info).
I found this rather weird and i wondered if Nokia E62 can be integrated with Cisco Call manager ,especially a device which is not Cisco compatible.The only possibility i can see from your answer is that the Nokia E62 might not be SIP enabled(correct me if i am wrong here!)
My objective is to send a message from a CUAE script to a nokia E62 device.Please excuse me if my posting is not in the right place.i would be highly grateful to you if you could give me pointers to an appropiate location where i can get my queries answered.

Integration with Cisco Call Manager?

We have Cisco VOIP phones and we would like to continue managing calls with Cisco Call Manager. We currently have voicemail on Cisco Unity. We currently have Exchange 2010, but plan to start using Exchange 2013 soon.
However, we would like to migrate voicemail service from Cisco Unity to Exchange Unified Messaging and also want to take advantage of most of the voicemail-related features of UM such as voice to text sent to email, voice mail waiting indicator light on
the phones and sending voice mail audio attachments to email.
Is Exchange 2013 Unified Messaging compatible Cisco phones that are managed by Cisco Call Manager?
We have 500 users and 2 Exchange 2010 servers (1 CAS and 1 Mailbox Server). We now have a few Exchange 2013 licenses available in addition to our existing 2010 licenses that are already used on our existing 2 servers. Can we keep the 2 existing
Exchange 2010 servers as they are and create a new Unified Messaging server on Exchange 2013 in the same environment or do we need to upgrade all the 2010 servers to 2013 if we use Unified Messaging on 2013?

Hi Sachin,
We do run a hybrid Callmanager to Nortel Meridian setup (works well).
Here are some great docs;
Cisco Unified CallManager
Case Study: Nortel 61C PBX to Cisco IP Telephony Migration
From this good doc;
http://www.cisco.com/en/US/products/sw/voicesw/ps556/products_white_paper09186a00801115e0.shtml
Nortel Meridian PBX and Cisco CallManager Integration
http://www.cisco.com/en/US/products/sw/voicesw/ps556/products_configuration_example09186a008011888c.shtml
Cisco Unified CallManager System Guide, Release 4.2(1)
Cisco DPA Integration
http://www.cisco.com/en/US/products/sw/voicesw/ps556/products_administration_guide_chapter09186a008055cd53.html
Hope this helps! Let me know if you need additional info.
Rob

Hi Team, I wuold like to know if you have any app to make Firefox OS working with cisco Call Manager 10.5. Something like Cisco Jabber for Android or iOS.

I'm interesting on buying a Firefox Smart Phone, but
I would like to know if are any app to install on Firefox OS smart phone in order to work with cisco call manager 10.5.
Something like Cisco Jabber for Android o iOS.
Thanks,

Hi Itech,
If Cisco Jabber has a webapp, or mobile version of their website available, you should technically be able to access it through Firefox OS.
You may also search Firefox Marketplace for an alternative solution:
* [https://marketplace.firefox.com/]
- Ralph

Wlc 5508 management interface vlan - access point vlan

Is it required that the access points are in the same vlan as the management interface on a wlc 5508?

There is a story behind this .. Just yesterday my guy was like "aps wont join" .. I let him hammer away at it .. It was the check box
"Satisfaction does not come from knowing the solution, it comes from knowing why." - Rosalind Franklin
‎"I'm in a serious relationship with my Wi-Fi. You could say we have a connection."

Cisco Ironport management interface IP configuration?

Hi,
For configuring the management interface IP for Cisco Ironport device, should it be on the public IP address or private IP address? Could you please confirm the IP address desing for the ironport management interface? thanks
arman

Greetings Aman,
The answer to this question depends on several factors, what you intend to do with the appliance, how you intend on allowing access to the appliance and where it sits in your network. Typically customers will utilize the management interface on their internal network thus giving it a private IP. This way the web interface, ssh and ftp access are allowed internally but not to the public. Those services can be enabled on other interfaces as well, but the most common practice is to set up the management interface for internal access only on your private network.
Christopher C Smith
CSE
Cisco IronPort Customer Support

Help with J2EE Project Management

Hi,
We are about to begin a large J2EE project and are wondering if anyone could help with the following questions:
1. Given the division of labor on J2EE projects (JSP developers, EJB developers, application deployers, etc...), what are "best practices" for building a team and ensuring that they communicate well after the design phase? How will the left arm know what the right arm is doing?
2. What documentation should be produced during the design phase to give to the developers? Will this allow them to go off and develop independently of each other?
3. Is there a "best practices" document anywhere on J2EE project management?
Thanks in advance!!

Hi,
I feel any project to start with should have a prior planning,that too particularly for Object oriented programming projects,I feel UML is the best tool for entire process.I think rational software has got lot of Project Management Tools(PMT) and products at all stages.Please go through the rational.com site and hope you could find some info.I feel the answer to your second question is partly 'yes' and partly 'no'.The modules that you can split it up which have got some independent attributes,but it should not be too much in your project,then it affects the work matrix/There should be a optimal process to decide and that you can yourself formulate depending on the time frame,either way the last step of build or integration is not flexible enough that you should mind,modular flexibility can be there but the integration stage you are tied with a fixed process.So plan accordingly using a PMT tool for any project that matters and all the best.Bye
Hari

WLC 5508 Management Interface Connection

I'm setting up a new 5508. I've used the config from a 4402, have successfully connected to the Service port to manage the device, but for some reason cannot connect to the Management interface. In this case, port 1.
The service port is connected to a Catalyst switch and grabbed an ip address (10.2.x.x subnet) no problem. I can access the 5508 via https using the SP. However, port 1 is connected to the same Catalyst switch, but on a different vlan (subnet 10.20.x.x). Both ends show that the interfaces are up, I can ping the interface from any other host on the network, but when I try to manage the device via https I cannot connect. We are using WCS and I cannot add the device from the WCS. About all I can do is ping that interface.
I've probably overlooked something very basic, but I'm baffled.

Thanks for the reply.
No, definitely not that. I have all of those enabled. I have the SP connected to another vlan on the same switch and can manage through that port(https, telnet). I've tried about every combination of trunk port, access port, etc. I'm beginning to suspect the GBICs (10baseT), but both ends show that I am connected at 1000 and I can ping the ip address of the management interface.

Any one using/deployed Telematrix phones with Cisco Call Manager

Any one using/deployed Telematrix phones with Cisco Call Manager

Yes, it does:
Cisco Unified IP Phone Series 7900
http://www.cisco.com/en/US/docs/voice_ip_comm/cucm/compat/ccmcompmatr.html#wp51474
Config on CUCM itself is no different from any other phones neither other requirements like DLUs.
Of course you should already have APs for connectivity.
HTH
java
if this helps, please rate

Help with Cisco Output Interpreter tool!!

Hi All,
I am experiencing a problem with Cisco Output Interpreter tool.
While the tool is working fine and displaying the "CONFIGURATION COMMAND REFERENCE NOTIFICATIONS (if any)" very effectively but I am unable to use the hyperlink to get an understanding about a particular command.
When I click on a particular command(hyperlink) it pops up another window and the below error is displayed.
Not Found
The requested URL /cgi-bin/Support/Cmdlookup/ios-command-lookup.pl was not found on this server.
Additionally, a 404 Not Found error was encountered while trying to use an ErrorDocument to handle the request.
Anyone else had/have this particular error. Could you please help me with this.
Apologies if this topic does not belong to this group.
Thanks in advance
Sam

Noone to help me on this?

Help for Cisco Security Manager

Hi All,
Please help me how cisco security manger is managing logs from different devices.
For example cisco security manager can manage FWSM, ASA, IPS devices.
Does it stores logs from this devices into some central location where CSM is being installed in some database or some file.
Can I be able to read logs for all those devices including CSM from one single point. Please help me.

Hi Bidyut,
When CSM services are running, Event Viewer can show the events in real time.
You are right about backup. When CSM application backup is running, its services on the server are stopped. So, there is a risk of loosing logging events that are sent to CSM server during the period of backup. By scheduling backup out of user-activity hours, risk of losing important events can be minimized.
On the other hand, events on IPS devices have to be polled from the device. So, there is no loss of IPS events in case of CSM application backup.
Thanks & Regards,
Chetan

Cisco UCS Managment interface

Hi Dear
Which is the function of the management interface of a Cisco UCS server? Only monitoring ?
Best Regards

Hi,
The management interface present in the Cisco UCS C-Series is a out-of-band interface that provides to you access to Cisco Integrated Management Controller (CIMC) where you can perform all management/monitoring tasks related the hardware set.
You can find more information about the CIMC in this link:
http://www.cisco.com/c/en/us/support/servers-unified-computing/ucs-c-series-integrated-management-controller/tsd-products-support-series-home.html
Regards,
Richard

Help with Cisco 5508 management interface

Similar Messages

Maybe you are looking for