Help with Cisco ASA 5500 and NAS drives

Hello:
I have 2 My Book World Edition II NAS drives. They both are configured to use a static IP address and both are on the same workgroup.
One of them is supposed to be replaced with a newer one that I just installed yesterday.
What I am trying to do is to transfer all the information from NAS1 to NAS2.
Both are connected to a Cisco VPN router.
I created a batch file that was basically several xcopy commands to copy all the information from NAS1 to NAS2.
As this process was going to take like 8 hours I ran the batch file yesterday at 4:00PM when everyone was logged off the NAS drives.
To my surprise this morning I found out that only a portion of the files were copied from the NAS1 to the NAS2.
After reading the system logs of the NAS1 drive I found a lot of errors.For example:
getpeername failed. Error was Transport endpoint is not connected
Error writing 4 bytes to client. -1. (Connection reset by peer)
write_data: write failure in writing to client 192.168.10.105. Error Connection reset by peer
Error writing 4 bytes to client. -1. (Connection reset by peer)
write_data: write failure in writing to client 192.168.10.105. Error Connection reset by peer
Error writing 4 bytes to client. -1. (Connection reset by peer)
write_data: write failure in writing to client 192.168.10.105. Error Connection reset by peer
Error writing 4 bytes to client. -1. (Connection reset by peer)
write_data: write failure in writing to client 192.168.10.105. Error Connection reset by peer
writing 4 bytes to client. -1. (Connection reset by peer)
write_data: write failure in writing to client 0.0.0.0. Error Connection reset by peer
getpeername failed. Error was Transport endpoint is not connected
Someone suggested that the problem has to do with the network configuration.
The suggestion was to change from "auto-negotiate" to Full Duplex 100 on the Cisco VPN router configuration.
What do you think? Could this be the problem?
Thanks and help is greatly appreciated.

Similar Messages

How to configure Cisco ASA 5500 to work with the iPhone

We have Cisco ASA 5510 (latest firmware version), and apparently, according to Cisco website it is compatible with new iPhone 3G's IPSec client:
http://www.cisco.com/en/US/docs/security/vpnclient/cisco_vpnclient/iPhone/2.0/connectivity/guide/iphone.html
We've setup our first iPhone properly. It connects fine to the network, shows VPN connection as active. Gets a private IP address. But does not let any traffic go to the internal network. We thought it might be DNS problem, but it cannot connect to Exchange server even when using IP address instead of DNS. No luck either.
After checking ASA logs, we found that iPhone goes through Phase 1 authentication correctly. But then gives some kind of error, mentioning "Attribute 5".
Has anybody been successful configuring ASA5500 series (in particular 5510) to be used with iPhone?
I noticed that many people are having these problems.
Please do not post to this topic if you have ANY OTHER Cisco device.
Cisco specifies that iPhone is compatible only with Cisco ASA 5500 Security Appliances and PIX Firewalls. Neither Cisco IOS VPN routers nor the VPN 3000 Series Concentrators support the iPhone VPN capabilities.
Let's keep this topic only for users of ASA 5500 series and PIX Firewalls.
It would be extremely helpful for a large number of users if somebody posted a list of settings for ASA5500 or PIX firewall that DO work with iPhone 2.0
Thank you!
Oleg R

We found the solution and a bug in Cisco firmware (seems to be a bug).
First of all, thanks to our Chief Systems Architect Seb, here is a config that worked for us on a Cisco 5520 (latest firmware).
access-list iphone_splitTunnelAcl standard permit <insert ip> <insert mask>
access-list iphone_splitTunnelAcl standard permit <insert ip> <insert mask>
crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec transform-set iphone esp-3des esp-sha-hmac
crypto ipsec transform-set iphone mode transport
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto dynamic-map SYSTEMDEFAULT_CRYPTOMAP 65535 set pfs
crypto dynamic-map SYSTEMDEFAULT_CRYPTOMAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5 iphone
crypto map outside_map 10 match address vpn
crypto map outside_map 10 set transform-set ESP-AES-256-SHA
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEMDEFAULT_CRYPTOMAP
crypto map outside_map interface outside
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
crypto isakmp policy 20
authentication pre-share
encryption aes-256
hash sha
group 5
lifetime 86400
crypto isakmp nat-traversal 20
group-policy iphone internal
group-policy iphone attributes
wins-server value <insert ip> <insert ip>
dns-server value <insert ip> <insert ip>
vpn-tunnel-protocol IPSec
ipsec-udp enable
ipsec-udp-port 10000
split-tunnel-policy tunnelspecified
split-tunnel-network-list value iphone_splitTunnelAcl
default-domain value <insert domain name>
tunnel-group iphone type remote-access
tunnel-group iphone general-attributes
address-pool VPN-Pool
authentication-server-group ActiveDirectory2
default-group-policy iphone
tunnel-group iphone ipsec-attributes
pre-shared-key <insert pre-shared key>
For iPhone you have to be using IPSec tab for configuration.
We tried to set up this config using the wizards, but it would not work.
Later it turned out that wizards by default set this setting:
"crypto isakmp nat-traversal 20"
equal to zero and there is no way to change it from the GUI.
Only after we changed it (increased the value from 0 to 20) through the command line the connection started working perfectly.
Please let me know how it works out for you.
Message was edited by: Rogik
Message was edited by: Rogik

Setting up site to site vpn with cisco asa 5505

I have a cisco asa 5505 that needs to be set up for site to site vpn to a cisco asa 5500. The 5505 is the remote office and the 5500 is the main office.
IP of remote office router is 71.37.178.142
IP of the main office firewall is 209.117.141.82
Can someone tell me if my config is correct, this is the first time I am setting this up and it can not be tested until I set it up at the remote office. I would rather know its correct before I go.
ciscoasa# show run
: Saved
ASA Version 7.2(4)
hostname ciscoasa
domain-name default.domain.invalid
enable password TMACBloMlcBsq1kp encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
interface Vlan1
nameif inside
security-level 100
ip address 192.168.1.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address dhcp setroute
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
ftp mode passive
dns server-group DefaultDNS
domain-name default.domain.invalid
access-list outside_1_cryptomap extended permit ip host 71.37.178.142 host 209.117.141.82
access-list inside_nat0_outbound extended permit ip 192.168.1.0 255.255.255.0 host 209.117.141.82
access-list inside_nat0_outbound extended permit ip host 71.37.178.142 host 209.117.141.82
pager lines 24
logging asdm informational
mtu inside 1500
mtu outside 1500
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-524.bin
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list inside_nat0_outbound
nat (inside) 1 0.0.0.0 0.0.0.0
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
http server enable
http 192.168.1.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto map outside_map 1 match address outside_1_cryptomap
crypto map outside_map 1 set pfs group5
crypto map outside_map 1 set peer 209.117.141.82
crypto map outside_map 1 set transform-set ESP-AES-256-SHA
crypto map outside_map interface outside
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption aes-256
hash sha
group 5
lifetime 86400
telnet timeout 5
ssh timeout 5
console timeout 0
vpdn username [email protected] password ********* store-local
dhcpd auto_config outside
dhcpd address 192.168.1.2-192.168.1.129 inside
dhcpd enable inside
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
service-policy global_policy global
prompt hostname context
Cryptochecksum:7e338fb2bf32a9ceb89560b314a5ef6c
: end
ciscoasa#
Thanks!

Hi Mandy,
By using following access list define Peer IP as source and destination
access-list outside_1_cryptomap extended permit ip host 71.37.178.142 host 209.117.141.82
you are not defining the interesting traffic / subnets from both ends.
Make some number ACL 101 as you do not have to write the extended keyword then if you like as follows, or else NAME aCL will also work:
access-list outside_1_cryptomap extended ip 192.168.200.0 0.0.0.255 192.168.100.0 0.0.0.255
access-list outside_1_cryptomap extended ip 192.168.200.0 0.0.0.255 192.168.100.0 0.0.0.255
access-list 101 remark CCP_ACL Category=4 access-list 101 remark IPSEC Rule
!.1..source subnet(called local encryption domain) at your end 192.168.200.0
!..2.and destination subnet(called remote encryption domain)at other end 192.168.100.0 !.3..I mean you have to define what subnets you need to communicate between which are behind these firewalls
!..4...Local Subnets behind IP of the main office firewall is 209.117.141.82 say
!...at your end 192.168.200.0
!..5.Remote Subnets behind IP of remote office router is 71.37.178.142 say
!...at other end 192.168.100.0
Please use Baisc Steps as follows:
A. Configuration in your MAIN office having IP = 209.117.141.82 (follow step 1 to 6)
Step 1.
Define Crypto ACL/ mirror ACL for other end (change source to destination and destination to source in other side router or VPN device and thats why they are called mirror ACL/ or also called Proxy ID or also called Proxy ACL, your interesting traffic , that you want to encrypt / trave/enter in the tunnel)
access-list outside_1_cryptomap extended ip 192.168.200.0 0.0.0.255 192.168.100.0 0.0.0.255
Step 2.
Config ISAKMP Policy with minimum 4 parameters are to be config for
crypto isakmp policy 10
authentication pre-share ---> Ist parameter of setting Authentication type ISAKMP Policy is OK
encryption aes-256   --->2nd parameter of ISAKMP Policy is OK
hash sha   ---> 3rd parameter of ISAKMP Policy is OK
group 5 ---> 4th parameter of ISAKMP Policy is OK
lifetime 86400 ------ > this 5th parameter is optional , and will negotiate for the less value at either end or by default is will be taken 86400
Step 3.
Define Preshared key or PKI which you will use with other side Peer address 71.37.178.142, either key type 0 is Plain text anyone can see it over internet, or use key type 6 for encrypted key , say your password is CISCO123
Here in your case in step 2 Authentication is using PSK, looks you have not defines Password
Use following command:
crypto isakmp key 0 CISCO123 address 71.37.178.142
or , but not both
crypto isakmp key 6 CISCO123 address71.37.178.142
step 4.
Define Transform set , which will be used for phase 2 tunnel parameters, if you use ESP it can have to sets one cor encryption and other for Authentication.
Here is yours one:
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
this is correct but give name somthing easier to remember /distinguish it is a transform set , like TSET1 instead of ESP-AES-256-SHA ,try following (here you are using ESP so for encryption we use first set as esp-des and for authentication we use second set esp-sha-hmac)
crypto ipsec transform-set TSET1 esp-des esp-sha-hmac
or
crypto ipsec transform-set TSET1 esp-aes-256 esp-sha-hmac
Suppose you are using only AH then as AH does not support encryption or confidentiality hence it always use onle one set not 2 sets like ESP(remember the difference) say for example only one set for auth etc but no set for encryption hence AH have no such sets like ah-des or ah-3des or ah-aes, it has only second set for authentication like
ah-sha-hmac or ah-md5-hmac
crypto ipsec transform-set TSET1 ah-sha-hmac
or
crypto ipsec transform-set TSET1 ah-md5-hmac
Step 5.
Now configure Crypto MAP as follows and only one CMPA can be applied to OUTSIDE Interface as VPN tunnel is alsways applied for traffic from inside subnets to outside subnets and only once Cryptomap can be applied to OUTSIDE Interface and hence for several VPN peers from different vendors we use seq no 10, 2 30 for different tunnels in one single CMAP:
crypto map ipsec-isakmp
1. Define peer -- called WHO to set tunnel with
2. Define or call WHICH - Transform Set
3. Define WHAT to call interesting traffic define in your ACL or Proxy ID or Proxy ACL in step 1 using match address
Like in your case it is but ipsec-isakmp keyword missing in the ;ast
crypto map outside_map 10 ipsec-isakmp
1. set peer 209.117.141.82 -----> is correct as this is your other side peer called WHO in my step
2. set transform-set TSET1 -----> is correct as this is WHICH, and only one transform set can be called
!..In you case it is correct
!...set transform-set ESP-AES-256-SHA (also correct)
3. match address outside_1_cryptomap ---->Name of the extended ACL define as WHAT to pass through this tunnel
4. set pfs group5 (this is optional but if config at one end same has to be config at other side peer as well)
Step 6.
Now apply this one crypto MAP to your OUTSIDE interface always
interface outside
crypto map outside_map
Configure the same but just change ACL on other end in step one by reversing source and destination
and also set the peer IP of this router in other end.
So other side config should look as follows:
B. Configuration in oyur Remote PEER IP having IP = 71.37.178.142 (follow step 7 to 12)
Step 7.
Define Crypto ACL/ mirror ACL for other end (change source to destination and destination to source in other side router or VPN device and thats why they are called mirror ACL/ or also called Proxy ID or also called Proxy ACL, your interesting traffic , that you want to encrypt / trave/enter in the tunnel)
access-list outside_1_cryptomap extended ip 192.168.100.0 0.0.0.255 192.168.200.0 0.0.0.255
Step 8.
Config ISAKMP Policy with minimum 4 parameters are to be config for
crypto isakmp policy 10
authentication pre-share ---> Ist parameter of setting Authentication type ISAKMP Policy is OK
encryption aes-256   --->2nd parameter of ISAKMP Policy is OK
hash sha   ---> 3rd parameter of ISAKMP Policy is OK
group 5 ---> 4th parameter of ISAKMP Policy is OK
lifetime 86400 ------ > this 5th parameter is optional , and will negotiate for the less value at either end or by default is will be taken 86400
Step 9.
Define Preshared key or PKI which you will use with other side Peer address key type 0 is Plain text anyone can see it over internet, or use key type 6 for encrypted key , say your password is CISCO123
Here in your case in step 8 Authentication is using PSK, looks you have not defines Password
Use following command:
crypto isakmp key 0 CISCO123 address 209.117.141.82
or , but not both
crypto isakmp key 6 CISCO123 address 209.117.141.82
step 10.
Define Transform set , which will be used for phase 2 tunnel parameters, if you use ESP it can have to sets one cor encryption and other for Authentication.
Here is yours one:
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
this is correct but give name somthing easier to remember /distinguish it is a transform set , like TSET1 instead of ESP-AES-256-SHA ,try following (here you are using ESP so for encryption we use first set as esp-des and for authentication we use second set esp-sha-hmac)
crypto ipsec transform-set TSET1 esp-des esp-sha-hmac
or
crypto ipsec transform-set TSET1 esp-aes-256 esp-sha-hmac
Suppose you are using only AH then as AH does not support encryption or confidentiality hence it always use onle one set not 2 sets like ESP(remember the difference) say for example only one set for auth etc but no set for encryption hence AH have no such sets like ah-des or ah-3des or ah-aes, it has only second set for authentication like
ah-sha-hmac or ah-md5-hmac
crypto ipsec transform-set TSET1 ah-sha-hmac
or
crypto ipsec transform-set TSET1 ah-md5-hmac
Step 11.
Now configure Crypto MAP as follows and only one CMPA can be applied to OUTSIDE Interface as VPN tunnel is alsways applied for traffic from inside subnets to outside subnets and only once Cryptomap can be applied to OUTSIDE Interface and hence for several VPN peers from different vendors we use seq no 10, 2 30 for different tunnels in one single CMAP:
crypto map    ipsec-isakmp
1. Define peer -- called WHO to set tunnel with
2. Define or call WHICH - Transform Set, only one is permissible
3. Define WHAT to call interesting traffic define in your ACL or Proxy ID or Proxy ACL in step 1 using match address
Like in your case it is but ipsec-isakmp keyword missing in the ;ast
crypto map outside_map 10 ipsec-isakmp
1. set peer 209.117.141.82 -----> is correct as this is your other side peer called WHO in my step
2. set transform-set TSET1 -----> is correct as this is WHICH, and only one transform set can be called
!..In you case it is correct
!...set transform-set ESP-AES-256-SHA (also correct)
3. match address outside_1_cryptomap ---->Name of the extended ACL define as WHAT to pass through this tunnel
4. set pfs group5 (this is optional but if config at one end same has to be config at other side peer as well)
Step 12.
Now apply this one crypto MAP to your OUTSIDE interface always
interface outside
crypto map outside_map
Now initite a ping
Here is for your summary:
IPSec: Site to Site - Routers
Configuration Steps
Phase 1
Step 1: Configure Mirrored ACL/Crypto ACL       for Interesting Traffic
Step 2: Configure ISAKMP Policy
Step 3: Configure ISAKMP Key
Phase 2
Step 4: Configure Transform Set
Step 5: Configure Crypto Map
Step 6: Apply Crypto Map to an Interface
To debug for Phase 1 and Phase 2. Store it in buffer without displaying logs on terminal.
Router#debug crpyto isakmp
Router#debug crpyto ipsec
Router(config)# logging buffer 7
Router(config)# logging buffer 99999
Router(config)# logging console 6
Router# clear logging
Configuration
In R1:
(config)# access-list 101 permit ipo host 10.1.1.1 host      10.1.2.1
(config)# crypto isakmp policy 10
(config-policy)# encryption 3des
(config-policy)# authentication pre-share
(config-policy)# group 2
(config-policy)# hash sha1
(config)# crypto isakmp key 0 cisco address 2.2.2.1
(config)# crypto ipsec transform-set TSET esp-3des      sha-aes-hmac
(config)# crypto map CMAP 10 ipsec-isakmp
(config-crypto-map)# set peer 2.2.2.1
(config-crypto-map)# match address 101
(config-crypto-map)# set transform-set TSET
(config)# int f0/0
(config-if)# crypto map CMAP
Similarly in R2
Verification Commands
#show crypto isakmp SA
#show crypto ipsec SA
Change to Transport Mode, add the following command in Step 4:
(config-tranform-set)# mode transport
Even after doing this change, the ipsec negotiation will still be done through tunnel mode if pinged from Loopback to Loopback. To overcome this we make changes to ACL.
Change to Aggressive Mode, replace the Step 3 command with these commands in R1:
(config)# crypto isakmp peer address 2.2.2.1
(config-peer)# set aggressive-mode password cisco
(config-peer)# set aggressive-mode clien-endpoint       ipv4-address 2.2.2.1
Similarly on R2.
The below process is for the negotiation using RSA-SIG (PKI) as authentication type
Debug Process:
After we debug, we can see the negotiation between the two peers. The first packet of the interesting traffic triggers the ISAKMP (Phase1) negotiation. Important messages are marked in BOLD and explanation in RED
R2(config)#do ping 10.1.1.1 so lo0 // Interesting Traffic
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 1.1.1.1, timeout is 2 seconds:
Packet sent with a source address of 2.2.2.2
Mar 2 16:18:42.939: ISAKMP:(0): SA request profile is (NULL) // Router tried to find any IPSec SA matching the outgoing connection but no valid SA has been found in Security Association Database (SADB)
Mar 2 16:18:42.939: ISAKMP: Created a peer struct for 20.1.1.10, peer port 500
Mar 2 16:18:42.939: ISAKMP: New peer created peer = 0x46519678 peer_handle = 0x8000000D
Mar 2 16:18:42.939: ISAKMP: Locking peer struct 0x46519678, refcount 1 for isakmp_initiator
Mar 2 16:18:42.939: ISAKMP: local port 500, remote port 500
Mar 2 16:18:42.939: ISAKMP: set new node 0 to QM_IDLE
Mar 2 16:18:42.939: ISAKMP:(0):insert sa successfully sa = 4542B818
Mar 2 16:18:42.939: ISAKMP:(0):Can not start Aggressive mode, trying Main mode. // Not an error. By default it is configured for Main Mode
Mar 2 16:18:42.939: ISAKMP:(0):No pre-shared key with 20.1.1.10! // Since we are using RSA Signature, this message. If we use pre-share, this is where it would indicate so!
Mar 2 16:18:42.939: ISAKMP:(0): constructed NAT-T vendor-rfc3947 ID
Mar 2 16:18:42.939: ISAKMP:(0): constructed NAT-T vendor-07 ID
Mar 2 16:18:42.939: ISAKMP:(0): constructed NAT-T vendor-03 ID
Mar 2 16:18:42.939: ISAKMP:(0): constructed NAT-T vendor-02 ID
Mar 2 16:18:42.939: ISAKMP:(0):Input = IKE_MESG_FROM_IPSEC, IKE_SA_REQ_MM
Mar 2 16:18:42.939: ISAKMP:(0):Old State = IKE_READY New State = IKE_I_MM1
Mar 2 16:18:42.943: ISAKMP:(0): beginning Main Mode exchange
Mar 2 16:18:42.943: ISAKMP:(0): sending packet to 20.1.1.10 my_port 500 peer_port 500 (I) MM_NO_STATE // Sending ISAKMP Policy to peer
Mar 2 16:18:42.943: ISAKMP:(0):Sending an IKE IPv4 Packet.
Mar 2 16:18:42.943: ISAKMP (0): received packet from 20.1.1.10 dport 500 sport 500 Global (I) MM_NO_STATE // Sending ISAKMP Policy to peer
Mar 2 16:18:42.947: ISAKMP:(0):Input = IKE_MESG_FROM_PEER, IKE_MM_EXCH
Mar 2 16:18:42.947: ISAKMP:(0):Old State = IKE_I_MM1 New State = IKE_I_MM2
Mar 2 16:18:42.947: ISAKMP:(0): processing SA payload. message ID = 0
Mar 2 16:18:42.947: ISAKMP:(0): processing vendor id payload
Mar 2 16:18:42.947: ISAKMP:(0): vendor ID seems Unity/DPD but major 123 mismatch // Do not worry about this! Not an ERROR!
Mar 2 16:18:42.947: ISAKMP:(0): vendor ID is NAT-T v2
Mar 2 16:18:42.947:.!!!!
Success rate is 80 percent (4/5), round-trip min/avg/max = 1/2/4 ms
R2(config)# ISAKMP:(0): processing vendor id payload
Mar 2 16:18:42.947: ISAKMP:(0): processing IKE frag vendor id payload
Mar 2 16:18:42.947: ISAKMP:(0):Support for IKE Fragmentation not enabled
Mar 2 16:18:42.947: ISAKMP : Scanning profiles for xauth ...
Mar 2 16:18:42.947: ISAKMP:(0):Checking ISAKMP transform 1 against priority 10 policy
Mar 2 16:18:42.947: ISAKMP:      encryption 3DES-CBC
Mar 2 16:18:42.947: ISAKMP:      hash SHA
Mar 2 16:18:42.947: ISAKMP:      default group 2
Mar 2 16:18:42.947: ISAKMP:      auth RSA sig
Mar 2 16:18:42.947: ISAKMP:      life type in seconds
Mar 2 16:18:42.947: ISAKMP:      life duration (VPI) of 0x0 0x1 0x51 0x80
Mar 2 16:18:42.947: ISAKMP:(0):atts are acceptable. Next payload is 0
Mar 2 16:18:42.947: ISAKMP:(0):Acceptable atts:actual life: 0
Mar 2 16:18:42.947: ISAKMP:(0):Acceptable atts:life: 0
Mar 2 16:18:42.947: ISAKMP:(0):Fill atts in sa vpi_length:4
Mar 2 16:18:42.947: ISAKMP:(0):Fill atts in sa life_in_seconds:86400
Mar 2 16:18:42.947: ISAKMP:(0):Returning Actual lifetime: 86400
Mar 2 16:18:42.947: ISAKMP:(0)::Started lifetime timer: 86400.
Mar 2 16:18:42.947: ISAKMP:(0): processing vendor id payload
Mar 2 16:18:42.947: ISAKMP:(0): vendor ID seems Unity/DPD but major 123 mismatch
Mar 2 16:18:42.947: ISAKMP:(0): vendor ID is NAT-T v2
Mar 2 16:18:42.947: ISAKMP:(0): processing vendor id payload
Mar 2 16:18:42.951: ISAKMP:(0): processing IKE frag vendor id payload
Mar 2 16:18:42.951: ISAKMP:(0):Support for IKE Fragmentation not enabled
Mar 2 16:18:42.951: ISAKMP:(0):Input = IKE_MESG_INTERNAL, IKE_PROCESS_MAIN_MODE
Mar 2 16:18:42.951: ISAKMP:(0):Old State = IKE_I_MM2 New State = IKE_I_MM2
Mar 2 16:18:42.951: ISAKMP (0): constructing CERT_REQ for issuer cn=ca_server OU=cisco C=India S=Karnataka L=Bangalore
Mar 2 16:18:42.951: ISAKMP:(0): sending packet to 20.1.1.10 my_port 500 peer_port 500 (I) MM_SA_SETUP // Sending Key Exchange Information to peer
Mar 2 16:18:42.951: ISAKMP:(0):Sending an IKE IPv4 Packet.
Mar 2 16:18:42.951: ISAKMP:(0):Input = IKE_MESG_INTERNAL, IKE_PROCESS_COMPLETE
Mar 2 16:18:42.951: ISAKMP:(0):Old State = IKE_I_MM2 New State = IKE_I_MM3
Mar 2 16:18:42.955: ISAKMP (0): received packet from 20.1.1.10 dport 500 sport 500 Global (I) MM_SA_SETUP // Receive key exchange information from peer
Mar 2 16:18:42.955: ISAKMP:(0):Input = IKE_MESG_FROM_PEER, IKE_MM_EXCH
Mar 2 16:18:42.955: ISAKMP:(0):Old State = IKE_I_MM3 New State = IKE_I_MM4
Mar 2 16:18:42.959: ISAKMP:(0): processing KE payload. message ID = 0
Mar 2 16:18:43.003: ISAKMP:(0): processing NONCE payload. message ID = 0
Mar 2 16:18:43.007: ISAKMP:(1008): processing CERT_REQ payload. message ID = 0
Mar 2 16:18:43.007: ISAKMP:(1008): peer wants a CT_X509_SIGNATURE cert
Mar 2 16:18:43.007: ISAKMP:(1008): peer wants cert issued by cn=ca_server OU=cisco C=India S=Karnataka L=Bangalore
Mar 2 16:18:43.007: Choosing trustpoint CA_Server as issuer
Mar 2 16:18:43.007: ISAKMP:(1008): processing vendor id payload
Mar 2 16:18:43.007: ISAKMP:(1008): vendor ID is Unity
Mar 2 16:18:43.007: ISAKMP:(1008): processing vendor id payload
Mar 2 16:18:43.007: ISAKMP:(1008): vendor ID seems Unity/DPD but major 180 mismatch
Mar 2 16:18:43.007: ISAKMP:(1008): vendor ID is XAUTH
Mar 2 16:18:43.007: ISAKMP:(1008): processing vendor id payload
Mar 2 16:18:43.007: ISAKMP:(1008): speaking to another IOS box!
Mar 2 16:18:43.007: ISAKMP:(1008): processing vendor id payload
Mar 2 16:18:43.007: ISAKMP:(1008):vendor ID seems Unity/DPD but hash mismatch
Mar 2 16:18:43.007: ISAKMP:received payload type 20
Mar 2 16:18:43.007: ISAKMP (1008): His hash no match - this node outside NAT
Mar 2 16:18:43.007: ISAKMP:received payload type 20
Mar 2 16:18:43.007: ISAKMP (1008): No NAT Found for self or peer
Mar 2 16:18:43.007: ISAKMP:(1008):Input = IKE_MESG_INTERNAL, IKE_PROCESS_MAIN_MODE
Mar 2 16:18:43.007: ISAKMP:(1008):Old State = IKE_I_MM4 New State = IKE_I_MM4
Mar 2 16:18:43.011: ISAKMP:(1008):Send initial contact
Mar 2 16:18:43.011: ISAKMP:(1008):My ID configured as IPv4 Addr, but Addr not in Cert!
Mar 2 16:18:43.011: ISAKMP:(1008):Using FQDN as My ID
Mar 2 16:18:43.011: ISAKMP:(1008):SA is doing RSA signature authentication using id type ID_FQDN
Mar 2 16:18:43.011: ISAKMP (1008): ID payload
          next-payload : 6
          type         : 2
          FQDN name    : R2
          protocol     : 17
          port         : 500
          length       : 10
Mar 2 16:18:43.011: ISAKMP:(1008):Total payload length: 10
Mar 2 16:18:43.019: ISAKMP (1008): constructing CERT payload for hostname=R2+serialNumber=FHK1502F2H8
Mar 2 16:18:43.019: ISAKMP:(1008): using the CA_Server trustpoint's keypair to sign
Mar 2 16:18:43.035: ISAKMP:(1008): sending packet to 20.1.1.10 my_port 500 peer_port 500 (I) MM_KEY_EXCH
Mar 2 16:18:43.035: ISAKMP:(1008):Sending an IKE IPv4 Packet.
Mar 2 16:18:43.035: ISAKMP:(1008):Input = IKE_MESG_INTERNAL, IKE_PROCESS_COMPLETE
Mar 2 16:18:43.035: ISAKMP:(1008):Old State = IKE_I_MM4 New State = IKE_I_MM5
Mar 2 16:18:43.047: ISAKMP (1008): received packet from 20.1.1.10 dport 500 sport 500 Global (I) MM_KEY_EXCH
// "MM_KEY_EXCH" indicates that the peers have exchanged DH Public keys and generated a shared secret!
Mar 2 16:18:43.047: ISAKMP:(1008): processing ID payload. message ID = 0
Mar 2 16:18:43.047: ISAKMP (1008): ID payload
          next-payload : 6
          type         : 2
          FQDN name    : ASA1
          protocol     : 0
          port         : 0
          length       : 12
Mar 2 16:18:43.047: ISAKMP:(0):: peer matches *none* of the profiles // Normal Message! Not an error!
Mar 2 16:18:43.047: ISAKMP:(1008): processing CERT payload. message ID = 0
Mar 2 16:18:43.047: ISAKMP:(1008): processing a CT_X509_SIGNATURE cert
Mar 2 16:18:43.051: ISAKMP:(1008): peer's pubkey isn't cached
Mar 2 16:18:43.059: ISAKMP:(1008): Unable to get DN from certificate!
Mar 2 16:18:43.059: ISAKMP:(1008): Cert presented by peer contains no OU field.
Mar 2 16:18:43.059: ISAKMP:(0):: peer matches *none* of the profiles
Mar 2 16:18:43.063: ISAKMP:(1008): processing SIG payload. message ID = 0
Mar 2 16:18:43.067: ISAKMP:received payload type 17
Mar 2 16:18:43.067: ISAKMP:(1008): processing vendor id payload
Mar 2 16:18:43.067: ISAKMP:(1008): vendor ID is DPD
Mar 2 16:18:43.067: ISAKMP:(1008):SA authentication status:
          authenticated
Mar 2 16:18:43.067: ISAKMP:(1008):SA has been authenticated with 20.1.1.10
Mar 2 16:18:43.067: ISAKMP: Trying to insert a peer 40.1.1.1/20.1.1.10/500/, and inserted successfully 46519678. // SA inserted into SADB
Mar 2 16:18:43.067: ISAKMP:(1008):Input = IKE_MESG_FROM_PEER, IKE_MM_EXCH
Mar 2 16:18:43.067: ISAKMP:(1008):Old State = IKE_I_MM5 New State = IKE_I_MM6
Mar 2 16:18:43.067: ISAKMP:(1008):Input = IKE_MESG_INTERNAL, IKE_PROCESS_MAIN_MODE
Mar 2 16:18:43.067: ISAKMP:(1008):Old State = IKE_I_MM6 New State = IKE_I_MM6
Mar 2 16:18:43.071: ISAKMP:(1008):Input = IKE_MESG_INTERNAL, IKE_PROCESS_COMPLETE
Mar 2 16:18:43.071: ISAKMP:(1008):Old State = IKE_I_MM6 New State = IKE_P1_COMPLETE
Mar 2 16:18:43.071: ISAKMP:(1008):beginning Quick Mode exchange, M-ID of -1523793378
Mar 2 16:18:43.071: ISAKMP:(1008):QM Initiator gets spi
Mar 2 16:18:43.075: ISAKMP:(1008): sending packet to 20.1.1.10 my_port 500 peer_port 500 (I) QM_IDLE
Mar 2 16:18:43.075: ISAKMP:(1008):Sending an IKE IPv4 Packet.
Mar 2 16:18:43.075: ISAKMP:(1008):Node -1523793378, Input = IKE_MESG_INTERNAL, IKE_INIT_QM
Mar 2 16:18:43.075: ISAKMP:(1008):Old State = IKE_QM_READY New State = IKE_QM_I_QM1
Mar 2 16:18:43.075: ISAKMP:(1008):Input = IKE_MESG_INTERNAL, IKE_PHASE1_COMPLETE
Mar 2 16:18:43.075: ISAKMP:(1008):Old State = IKE_P1_COMPLETE New State = IKE_P1_COMPLETE
Mar 2 16:18:43.079: ISAKMP (1008): received packet from 20.1.1.10 dport 500 sport 500 Global (I) QM_IDLE // IPSec Policies
Mar 2 16:18:43.079: ISAKMP:(1008): processing HASH payload. message ID = -1523793378
Mar 2 16:18:43.079: ISAKMP:(1008): processing SA payload. message ID = -1523793378
Mar 2 16:18:43.079: ISAKMP:(1008):Checking IPSec proposal 1
Mar 2 16:18:43.079: ISAKMP: transform 1, ESP_3DES
Mar 2 16:18:43.079: ISAKMP:   attributes in transform:
Mar 2 16:18:43.079: ISAKMP:      SA life type in seconds
Mar 2 16:18:43.079: ISAKMP:      SA life duration (basic) of 3600
Mar 2 16:18:43.079: ISAKMP:      SA life type in kilobytes
Mar 2 16:18:43.079: ISAKMP:      SA life duration (VPI) of 0x0 0x46 0x50 0x0
Mar 2 16:18:43.079: ISAKMP:      encaps is 1 (Tunnel)
Mar 2 16:18:43.079: ISAKMP:      authenticator is HMAC-SHA
Mar 2 16:18:43.079: ISAKMP:(1008):atts are acceptable. // IPSec attributes are acceptable!
Mar 2 16:18:43.079: ISAKMP:(1008): processing NONCE payload. message ID = -1523793378
Mar 2 16:18:43.079: ISAKMP:(1008): processing ID payload. message ID = -1523793378
Mar 2 16:18:43.079: ISAKMP:(1008): processing ID payload. message ID = -1523793378
Mar 2 16:18:43.083: ISAKMP:(1008): Creating IPSec SAs
Mar 2 16:18:43.083:         inbound SA from 20.1.1.10 to 40.1.1.1 (f/i) 0/ 0
          (proxy 1.1.1.1 to 2.2.2.2)
Mar 2 16:18:43.083:         has spi 0xA9A66D46 and conn_id 0
Mar 2 16:18:43.083:         lifetime of 3600 seconds
Mar 2 16:18:43.083:         lifetime of 4608000 kilobytes
Mar 2 16:18:43.083:         outbound SA from 40.1.1.1 to 20.1.1.10 (f/i) 0/0
        (proxy 2.2.2.2 to 1.1.1.1)
Mar 2 16:18:43.083:         has spi 0x2B367FB4 and conn_id 0
Mar 2 16:18:43.083:         lifetime of 3600 seconds
Mar 2 16:18:43.083:         lifetime of 4608000 kilobytes
Mar 2 16:18:43.083: ISAKMP:(1008): sending packet to 20.1.1.10 my_port 500 peer_port 500 (I) QM_IDLE
Mar 2 16:18:43.083: ISAKMP:(1008):Sending an IKE IPv4 Packet.
Mar 2 16:18:43.083: ISAKMP:(1008):deleting node -1523793378 error FALSE reason "No Error"
Mar 2 16:18:43.083: ISAKMP:(1008):Node -1523793378, Input = IKE_MESG_FROM_PEER, IKE_QM_EXCH
Mar 2 16:18:43.083: ISAKMP:(1008):Old State = IKE_QM_I_QM1 New State = IKE_QM_PHASE2_COMPLETE // At this point tunnels are up and ready to pass traffic!
Verification Commands
#show crypto isakmp SA
#show crypto ipsec SA
Kindly rate if you find the explanation useful !!
Best Regards
Sachin Garg

Azure multiple site-to-site VPNs (dynamic gateway) with Cisco ASA devices

Hello
I've been experimenting with moving certain on-premise servers to Azure however they would need a site-to-site VPN link to our many branch sites e.g. monitoring of nodes.
The documentation says I need to configure a dynamic gateway to have multiple site-to-site VPNs. This is not a problem for our typical Cisco ISR's. However three of our key sites use Cisco ASA devices which are listed as 'Not Compatible' with dynamic routing.
So I am stuck...
What options are available to me? Is there any sort of tweak-configuration to make a Cisco ASA work with Azure and dynamic routing?
I was hoping Azure's VPN solution would be very flexible.
Thanks

Hello RTF_Admin,
1. Which is the Series of CISCO ASA device you are using?
Thank you for your interest in Windows Azure. The Dynamic routing is not supported for the Cisco ASA family of devices.
Unfortunately, a dynamic routing VPN gateway is required for Multi-Site VPN, VNet to VNet, and Point-to-Site.
However, you should be able to setup a site-to-site VPN with Cisco ASA 5505 series security appliance as demonstrated in this blog:
Step-By-Step: Create a Site-to-Site VPN between your network and Azure
http://blogs.technet.com/b/canitpro/archive/2013/10/09/step-by-step-create-a-site-to-site-vpn-between-your-network-and-azure.aspx
You can refer to this article for Cisco ASA templates for Static routing:
http://msdn.microsoft.com/en-us/library/azure/dn133793.aspx
If your requirement is only for Multi-Site VPN then there is no option but to upgrade the device as Multisite VPN requires dyanmic routing and unfortunately there is no tweak or workaround due to hardware compatibility issue.
I hope that this information is helpful
Thanks,
Syed Irfan Hussain

Azure Site to Site VPN with Cisco ASA 5505

I have got Cisco ASA 5505 device (version 9.0(2)). And i cannot connect S2S with azure (azure network alway in "connecting" state). In my cisco log:
IP = 104.40.182.93, Keep-alives configured on but peer does not support keep-alives (type = None)
Group = 104.40.182.93, IP = 104.40.182.93, QM FSM error (P2 struct &0xcaaa2a38, mess id 0x1)!
Group = 104.40.182.93, IP = 104.40.182.93, Removing peer from correlator table failed, no match!
Group = 104.40.182.93, IP = 104.40.182.93,Overriding Initiator's IPSec rekeying duration from 102400000 to 4608000 Kbs
Group = 104.40.182.93, IP = 104.40.182.93, PHASE 1 COMPLETED
I have done all cisco s2s congiguration over standard wizard cos seems your script for 8.x version of asa only?
(Does azure support 9.x version of asa?)
How can i fix it?

Hi,
As of now, we do not have any scripts for Cisco ASA 9x series.
Thank you for your interest in Windows Azure. The Dynamic routing is not supported for the Cisco ASA family of devices.
Unfortunately, a dynamic routing VPN gateway is required for Multi-Site VPN, VNet to VNet, and Point-to-Site.
However, you should be able to setup a site-to-site VPN with Cisco ASA 5505 series security appliance as
demonstrated in this blog:
Step-By-Step: Create a Site-to-Site VPN between your network and Azure
http://blogs.technet.com/b/canitpro/archive/2013/10/09/step-by-step-create-a-site-to-site-vpn-between-your-network-and-azure.aspx
You can refer to this article for Cisco ASA templates for Static routing:
http://msdn.microsoft.com/en-us/library/azure/dn133793.aspx
Did you download the VPN configuration file from the dashboard and copy the content of the configuration
file to the Command Line Interface of the Cisco ASDM application? It seems that there is no specified IP address in the access list part and maybe that is why the states message appeared.
According to the
Cisco ASA template, it should be similar to this:
access-list <RP_AccessList>
extended permit ip object-group
<RP_OnPremiseNetwork> object-group <RP_AzureNetwork>
nat (inside,outside) source static <RP_OnPremiseNetwork>
<RP_OnPremiseNetwork> destination static <RP_AzureNetwork>
<RP_AzureNetwork>
Based on my experience, to establish
IPSEC tunnel, you need to allow the ESP protocol and UDP Port 500. Please make sure that the
VPN device cannot be located behind a NAT. Besides, since Cisco ASA templates are not
compatible for dynamic routing, please make sure that you chose the static routing.
Since you configure the VPN device yourself, it's important that you would be familiar with the device and its configuration settings.
Hope this helps you.
Girish Prajwal

How we archieve configuration for Cisco ASA 5500 series appliances

Hi,
We need to archieve configuration for Cisco ASA 5500 series appliances.
We have Cisco works LMS 3.0.1.
Device package installed is 4.2
Any help would be appricated.
Thanks in advance.
Samir

Hi ,
Thanks for your answer.
Right now we are using TACAS to login in to the ASA. That means we need single username and password to login via
Cisoworks. Am I correct ?
Waiting for your reply.
thanks,
Samir

New help with my mac air and airport extreme time capsule dont know how to save to time capsule and use as a external hd

new help with my mac air and airport extreme time capsule dont know how to save to time capsule and use as a external hd would like 2 store my home videos and pictures on the time machine (ONLY) as the MAC AIR has storage space limited space please help. THANK YOU.

See the info here about sharing or using the TC for data.
Q3 http://pondini.org/TM/Time_Capsule.html
It is extremely important you realise.. the Time Capsule was never designed for this.
It is a backup target for Time Machine.. that is the software on the computer that does backups.. it has no direct connection to the Time Capsule.
It has no ability to back itself up.. unlike all other NAS in the market. It is therefore likely one day you will lose all your files unless you seriously work out how to backup.
The TC is slow to spin up the hard disk and fast to spin down. iTunes and iPhoto will continually lose connection to their respective libraries.
iPhoto in particular is easy to corrupt when you move photos over wireless into the library.. once corrupted all is corrupt. A single photo will ruin it all.. so backup is utterly essential.
Time Machine cannot do backups of network drives. ie the TC. You will need a different backup software like CCC. You will then need another target to backup to..

Help with opening Adobe Reader and downloading updates

I can not open Adobe .pdf files any longer (this started yesterday, prior to that I could open adobe files).
When I double click a .pdf file I get this notice on my screen: Windows cannot access the specified device path or file. You may not have the appropriate permission to access file.
So I went to the Adobe download site to download a new copy of Adobe. When I start the download I get this on the screen: The instruction at "0x0e3a0068" referenced memory at "0x0e3a0068." The memory could not be written. Then two options are listed: click OK to terminate or cancel to debug. So I click on cancel and I get this on my screen: Internet Explorer has closed this webpage to help protect your computer. A malfunctioning or malicious addon has caused I.E. to close this webpage.
I don't have AVG running, I do have avast but I've disabled it. I ran Registry Mechanic and an I.E. erasure program but nothing helps.
I have gone into I.E. and reduced the security level to its lowest state but no joy.
So, any ideas or suggestions on what's the problem and how to overcome it would be appreciated. Thanks, in advance, for your reply. Jim R.

Hi Mike..tried that as well but no joy. A friend of mine was looking at it all and noticed that it was an I.E. thing as far as not letting me redownload the reader so I went to Mozilla Firefox and I could download a new version but....whenever I attempt to open a .pdf file I get that message, "Windows can not open the specified device, path or file. You man not have the appropriate permissions to access the item."
Damn...this is irritating as I need to get to some of thos files as I need them for a Journal I'm working on as editor-in-chief.
It all worked just fine last Saturday but starting Monday when I was on my flight out to D.C. no joy.
Sigh...Jim R.
Jim R.
Date: Tue, 1 Dec 2009 14:50:27 -0700
From: [email protected]
To: [email protected]
Subject: Help with opening Adobe Reader and downloading updates
Under the help menu, there is an option to repair the installation of reader. Did you try that?
>

Need help with my iPhone 5 and my Macbook Pro.

Need help with my iPhone 5 and my Macbook Pro. I was purchased some music on itunes at my mac. Some reason I deleted those music from both on Mac and iPhone 5. Today, I went to my iPhone iTunes store inside of iCloud to redownload my puchased. But those song won't able to sync back to my iTunes library on my Mac. Can anyone help me with that ??....
iPhone 5, iOS 6.0.1

You've posted to the iTunes Match forum, which your question does not appear to be related to. You'll get better support responses by posting to either the iTunes for Mac or iTunes for Windows forum. Which ever is more appropriate for your situation.

Barbara Brundage, can you help with PS Elements 11 and Epson R2000 printer issue?

Seeking help with PS Elements 11 which does not work with Epson r2000 printer. Epson tech support could not fix, said it is PS e11 problem. Receive prompt on PS e11 screen when I try to print stating "not compatible or settings are not correct. Have set PS to manage color and printer manages color to off. Would appreciate any suggestions. Thank you.

Hi,
Sincerely appreciate your help. Running Windows 7 on a Dell XPS420. System has been very stable for years. Before purchasing the Epson r2000, I owned an r1800 which was an excellent printer but after seven years started to exhibit paper feed problems. The r1800 worked with all applications and I was well satisfied with the saturation, contrast, etc. printing mostly 8x10 and 11x17 prints.
Thank you for the information about the # of installs for PS E11, will try uninstall/reinstall this morning.
Will let you know how things go.
Richard
Date: Thu, 12 Sep 2013 19:47:38 -0700
From: [email protected]
To: [email protected]
Subject: Barbara Brundage, can you help with PS Elements 11 and Epson R2000 printer issue?
    Re: Barbara Brundage, can you help with PS Elements 11 and Epson R2000 printer issue?
    created by Barbara B. in Photoshop Elements - View the full discussion
What operating system are you using?
     Please note that the Adobe Forums do not accept email attachments. If you want to embed a screen image in your message please visit the thread in the forum to embed the image at http://forums.adobe.com/message/5678022#5678022
     Replies to this message go to everyone subscribed to this thread, not directly to the person who posted the message. To post a reply, either reply to this email or visit the message page: http://forums.adobe.com/message/5678022#5678022
     To unsubscribe from this thread, please visit the message page at http://forums.adobe.com/message/5678022#5678022. In the Actions box on the right, click the Stop Email Notifications link.
     Start a new discussion in Photoshop Elements by email or at Adobe Community
For more information about maintaining your forum email notifications please go to http://forums.adobe.com/message/2936746#2936746.

Doese Cisco ASA 5500 has module increase performance VPN?

Dear All,
Doese Cisco ASA 5510 and 5505 has module for increase performance VPN ?
Best Regards,
Rechard

Rechard,
There is one built into every ASA. If you need better performance because you're limited by engine performance... you need to most likely move up to a bigged model.
Here is the datasheet for reference:
http://www.cisco.com/en/US/products/ps6120/prod_models_comparison.html
M.

VPN between ASA 5500 and Cisco 871

Hello.
I recently bought a Cisco 871 and an ASA 5500 device. I would like to configure a VPN connection (LAN-to-LAN), and I would like some help about the ports that need to be opened into both firewalls, ASA and 871.
Thank you.

Thank you. The routers where not syncronized.
I have installed on my CA server also an NTP server and everything works now.
I have one more question: how can I connect the CA server to separate zone on my ASA device? Let's say a DMZ zone?
I have 2 public IPs and I want to use one (let's say PRIMARY_IP) for the VPN tunnels, and the other one (let's call it SECONDARY_IP) for the CA server...In other words I want the SECONDARY_IP to be ?assigned? to the CA server; if someone wants to make requests for NTP, or SCEP, or ...let's say TFTP to the SECONDARY_IP, those requests to be forwarded behind the ASA, to the CA.
Can you help me?

Cisco Asa 5505 and Layer 3 Switch With Remote VPN Access

i got today a new CISCO LAYER 3 Switch .. so here is my scenrio
Cisco Asa 5505
I
Outside == 155.155.155.x
Inside = 192.168.7.1
VPN POOL Address = 10.10.10.1 - 10.10.10.20
Layer 3 Switch Config
Vlan 2
interface ip address = 192.168.1.1
Vlan 2
interface ip address = 192.168.2.1
Vlan 2
interface ip address = 192.168.3.1
Vlan 2
interface ip address = 192.168.4.1
Vlan 2
interface ip address = 192.168.5.1
ip Routing
So i want My Remote Access VPN clients to access all this Networks. So Please can you give me a helpfull trick or Link to configure the rest of my routing
Thank You all

When My Remote VPN is Connected , it reaches 192.168.7.2 of the Layer 3 VLan that's Connected to The ASA 5505 ,
But i can't reach the rest of the VLAN - example
192.168.1.1
192.168.1.2
192.168.1.3
192.168.1.4
192.168.1.5
But i can reach the Connected Interface Vlan to My ASA ..
So here i think iam miss configuration to my Route
Any Help Please this is urgent

Pleas help with my music files and folders on an external drive

A while back, I thought I had a virus on my C drive and was advised to by an external hard drive to move all my important files and folders to. As an inexperienced computer guy, this eventually led to a problem. I have many folders that shouldn't have been moved, main folders that were broken up, duplicates of songs, some song files that are empty, etc. This doesn't just apply to iTunes folders, it includes all the computer's music folders.
Can you please help me reorganize and delete duplicates (C and external drives)? Is there a quick way to search for song files that will not work? Is there a way to wipe out all iTunes files and start over without losing the songs bought via itunes?

Welcome to the Apple Discussions. I think you're in the wrong forum. This is the iDVD forum. If I read your question correctly you probably want the iTunes for Windows forum.
OT

Need some help with a Macally enclosure and a spare internal drive

Need some help with a Macally enclousure
Posted: Oct 1, 2010 10:55 AM
Reply Email
Aloha:
I have a Macally PHR-S100SUA enclousure that does not recognise,my WD 1001fals hard drive. It has worked just fine with other internal drives, but not this one?
This is a spare internal drive that I am trying to make an external drive to store back ups for a lot of data. But so far I can not get it recognized by the computer. Maybe I need different drivers?
Any suggestions?
Dan Page

Hi-
Drivers aren't typically needed for external enclosures.
Macally has none listed for that enclosure.
The same is true for the WD drive, internal or external; no drivers.
With the exception of high end PM multi drive enclosures, I can't think of any that use drivers.
How is the external connected?
Have you tried different cables, different ports?
Bad/damaged cables are fairly common.
Have you verified connections inside of the enclosure?

Help with Cisco ASA 5500 and NAS drives

Similar Messages

Maybe you are looking for