Help with GRUB[ok]- kernel panic[ok]- filesystem check failed[&nuked]
So todays story
1.My windows partition was overruned by viruses...
2. I reinstaled windows XP
3. I tried to repair grub but without sucess
So result: unbootable system.
plz help me fix that.
Last edited by ProzacR (2007-06-27 22:43:12)
Thank you, exactly what I needed.
Can be two things:
Grub specified the wrong root file system in menu.lst.
Try appending root=/dev/sda? to the grub boot command for arch (Replace ? with your arch root partition) If that fixes it, it was menu.lst in Ubuntu that broke it.
Second posibility: Grub did not specify the correct initrd image for arch.
Try specifying initrd as /boot/kernel26.img to the Grub boot configuration for arch.
It can also be both, then specify both, I doubt it and suspect the second scenario.
This should get you booted after fiddling a bit. Please re-run grub-install from the arch instance.
This site gives detailed instructions on how to make grub fly:
http://www.linuxforums.org/forum/linux- … -grub.html
Good luck. I hope this fixes it for you.
Similar Messages
-
Need help with the following kernel panic message
Interval Since Last Panic Report: 343442 sec
Panics Since Last Report: 1
Anonymous UUID: 20AE5901-94AA-497D-A08A-83DE6176E55A
Mon May 16 15:17:40 2011
panic(cpu 1 caller 0xffffff80002d1208): Kernel trap at 0xffffff80002c3762, type 14=page fault, registers:
CR0: 0x0000000080010033, CR2: 0xffffff80c95ab404, CR3: 0x00000000514f3000, CR4: 0x0000000000040660
RAX: 0xffffff800085ae38, RBX: 0x0000000000000000, RCX: 0x0000000000000004, RDX: 0x0000000000000004
RSP: 0xffffff80b2042948, RBP: 0xffffff80b20429a0, RSI: 0xffffff80c95ab404, RDI: 0xffffff80a9a2fd20
R8: 0x0000000000001800, R9: 0xffffff80a9a2fd20, R10: 0x00000000159ab001, R11: 0xffffff7f80e88fe2
R12: 0xffffff80a9a2fd20, R13: 0xffffff80c95ab404, R14: 0x0000000000001800, R15: 0x0000000000000020
RFL: 0x0000000000010202, RIP: 0xffffff80002c3762, CS: 0x0000000000000008, SS: 0x0000000000000010
Error code: 0x0000000000000000
Backtrace (CPU 1), Frame : Return Address
0xffffff80b20425e0 : 0xffffff8000204d15
0xffffff80b20426e0 : 0xffffff80002d1208
0xffffff80b2042830 : 0xffffff80002e3f4a
0xffffff80b2042840 : 0xffffff80002c3762
0xffffff80b20429a0 : 0xffffff7f80ea59e7
0xffffff80b2042a70 : 0xffffff7f80ea52ef
0xffffff80b2042ac0 : 0xffffff7f80e79966
0xffffff80b2042ba0 : 0xffffff80005523e8
0xffffff80b2042be0 : 0xffffff8000553029
0xffffff80b2042c60 : 0xffffff80005537d6
0xffffff80b2042db0 : 0xffffff80002ba1c4
0xffffff80b2043e50 : 0xffffff8000205536
0xffffff80b2043e80 : 0xffffff80002029eb
0xffffff80b2043ef0 : 0xffffff8000274176
0xffffff80b2043f60 : 0xffffff80002c3095
0xffffff80b2043fa0 : 0xffffff80002e4894
Kernel Extensions in backtrace (with dependencies):
com.apple.driver.AppleIntelHDGraphics(6.3.4)@0xffffff7f80e61000->0xffffff7f80f3 6fff
dependency: com.apple.iokit.IOPCIFamily(2.6.3)@0xffffff7f8081d000
dependency: com.apple.iokit.IONDRVSupport(2.2)@0xffffff7f8087b000
dependency: com.apple.iokit.IOGraphicsFamily(2.2)@0xffffff7f80853000
BSD process name corresponding to current thread: WindowServer
Mac OS version:
10J4138
Kernel version:
Darwin Kernel Version 10.7.4: Mon Apr 18 21:24:17 PDT 2011; root:xnu-1504.14.12~3/RELEASE_X86_64
System model name: MacBookPro8,1 (Mac-94245B3640C91C81)
System uptime in nanoseconds: 48514690935839
unloaded kexts:
com.apple.driver.AppleUSBUHCI 4.2.0 (addr 0xffffff7f810e4000, size 0x65536) - last unloaded 95251705762
loaded kexts:
com.pgp.kext.PGPnke 1.1.0
com.vmware.kext.vmnet 3.1.2
com.vmware.kext.vmioplug 3.1.2
com.vmware.kext.vmci 3.1.2
com.vmware.kext.vmx86 3.1.2
com.pgp.iokit.PGPwdeDriver 1.2.0d1
com.rim.driver.BlackBerryUSBDriverInt 0.0.64
com.apple.filesystems.afpfs 9.7 - last loaded 34795666277000
com.apple.nke.asp_tcp 5.0
com.apple.driver.AppleBluetoothMultitouch 54
com.apple.driver.AppleHWSensor 1.9.3d0
com.apple.driver.IOBluetoothBNEPDriver 2.4.5f1
com.apple.filesystems.autofs 2.1.0
com.apple.driver.AGPM 100.12.31
com.apple.driver.AppleMikeyHIDDriver 1.2.0
com.apple.driver.AppleHDA 2.0.5f13
com.apple.driver.AppleMikeyDriver 2.0.5f13
com.apple.driver.AppleUpstreamUserClient 3.5.7
com.apple.driver.AppleMCCSControl 1.0.20
com.apple.driver.AudioAUUC 1.57
com.apple.driver.AppleIntelHDGraphics 6.3.4
com.apple.driver.SMCMotionSensor 3.0.1d2
com.apple.Dont_Steal_Mac_OS_X 7.0.0
com.apple.driver.AudioIPCDriver 1.1.6
com.apple.driver.ACPI_SMC_PlatformPlugin 4.7.0a1
com.apple.driver.AppleLPC 1.5.1
com.apple.driver.AppleBacklight 170.0.46
com.apple.kext.AppleSMCLMU 1.5.2d10
com.apple.driver.AppleIntelSNBGraphicsFB 6.3.4
com.apple.driver.AppleUSBTCButtons 201.2
com.apple.driver.AppleUSBTCKeyboard 201.2
com.apple.driver.AppleIRController 303.8
com.apple.iokit.SCSITaskUserClient 2.6.8
com.apple.BootCache 31
com.apple.AppleFSCompression.AppleFSCompressionTypeZlib 1.0.0d1
com.apple.iokit.IOAHCIBlockStorage 1.6.4
com.apple.driver.AppleSDXC 1.0.2
com.apple.iokit.AppleBCM5701Ethernet 3.0.5b8
com.apple.driver.AppleFWOHCI 4.7.3
com.apple.driver.AirPort.Brcm4331 432.11.3
com.apple.driver.AppleUSBHub 4.2.0
com.apple.driver.AppleEFINVRAM 1.4.0
com.apple.driver.AppleSmartBatteryManager 160.0.0
com.apple.driver.AppleAHCIPort 2.1.7
com.apple.driver.AppleACPIButtons 1.3.6
com.apple.driver.AppleUSBEHCI 4.2.0
com.apple.driver.AppleRTC 1.3.1
com.apple.driver.AppleHPET 1.5
com.apple.driver.AppleSMBIOS 1.7
com.apple.driver.AppleACPIEC 1.3.6
com.apple.driver.AppleAPIC 1.4
com.apple.driver.AppleIntelCPUPowerManagementClient 142.6.0
com.apple.security.sandbox 1
com.apple.security.quarantine 0
com.apple.nke.applicationfirewall 2.1.11
com.apple.driver.AppleIntelCPUPowerManagement 142.6.0
com.apple.driver.IOBluetoothHIDDriver 2.4.5f1
com.apple.driver.AppleMultitouchDriver 207.11
com.apple.driver.AppleProfileReadCounterAction 17
com.apple.driver.DspFuncLib 2.0.5f13
com.apple.driver.AppleProfileTimestampAction 10
com.apple.driver.AppleProfileThreadInfoAction 14
com.apple.driver.AppleProfileRegisterStateAction 10
com.apple.driver.AppleProfileKEventAction 10
com.apple.driver.AppleProfileCallstackAction 20
com.apple.driver.AppleSMBusController 1.0.10d0
com.apple.iokit.IOFireWireIP 2.0.3
com.apple.iokit.IOSurface 74.2
com.apple.iokit.IOBluetoothSerialManager 2.4.5f1
com.apple.iokit.IOSerialFamily 10.0.3
com.apple.iokit.IOAudioFamily 1.8.3fc2
com.apple.kext.OSvKernDSPLib 1.3
com.apple.driver.AppleHDAController 2.0.5f13
com.apple.iokit.IOHDAFamily 2.0.5f13
com.apple.iokit.AppleProfileFamily 41
com.apple.driver.IOPlatformPluginFamily 4.7.0a1
com.apple.driver.AppleSMBusPCI 1.0.10d0
com.apple.driver.AppleBacklightExpert 1.0.1
com.apple.iokit.IONDRVSupport 2.2
com.apple.driver.AppleSMC 3.1.0d5
com.apple.driver.AppleThunderboltEDMSink 1.0.5
com.apple.driver.AppleThunderboltEDMSource 1.0.5
com.apple.iokit.IOGraphicsFamily 2.2
com.apple.driver.BroadcomUSBBluetoothHCIController 2.4.5f1
com.apple.driver.AppleUSBBluetoothHCIController 2.4.5f1
com.apple.iokit.IOBluetoothFamily 2.4.5f1
com.apple.driver.AppleThunderboltDPOutAdapter 1.2.0
com.apple.driver.AppleThunderboltDPInAdapter 1.2.0
com.apple.driver.AppleThunderboltDPAdapterFamily 1.2.0
com.apple.driver.AppleThunderboltPCIDownAdapter 1.1.5
com.apple.driver.AppleUSBMultitouch 207.5
com.apple.iokit.IOUSBHIDDriver 4.2.0
com.apple.driver.XsanFilter 402.1
com.apple.driver.AppleUSBMergeNub 4.2.2
com.apple.iokit.IOSCSIMultimediaCommandsDevice 2.6.8
com.apple.iokit.IOBDStorageFamily 1.6
com.apple.iokit.IODVDStorageFamily 1.6
com.apple.iokit.IOCDStorageFamily 1.6.1
com.apple.iokit.IOAHCISerialATAPI 1.2.6
com.apple.driver.AppleThunderboltNHI 1.2.3
com.apple.iokit.IOThunderboltFamily 1.3.5
com.apple.iokit.IOFireWireFamily 4.2.6
com.apple.iokit.IO80211Family 320.1
com.apple.iokit.IONetworkingFamily 1.10
com.apple.iokit.IOUSBUserClient 4.2.0
com.apple.iokit.IOAHCIFamily 2.0.6
com.apple.driver.AppleEFIRuntime 1.4.0
com.apple.iokit.IOHIDFamily 1.6.6
com.apple.iokit.IOSMBusFamily 1.1
com.apple.kext.AppleMatch 1.0.0d1
com.apple.security.TMSafetyNet 6
com.apple.iokit.IOUSBMassStorageClass 2.6.6
com.apple.driver.AppleUSBComposite 3.9.0
com.apple.iokit.IOSCSIBlockCommandsDevice 2.6.8
com.apple.iokit.IOSCSIArchitectureModelFamily 2.6.8
com.apple.iokit.IOUSBFamily 4.2.2
com.apple.driver.DiskImages 289
com.apple.iokit.IOStorageFamily 1.6.3
com.apple.driver.AppleACPIPlatform 1.3.6
com.apple.iokit.IOPCIFamily 2.6.3
com.apple.iokit.IOACPIFamily 1.3.0
Model: MacBookPro8,1, BootROM MBP81.0047.B0E, 2 processors, Intel Core i7, 2.7 GHz, 8 GB, SMC 1.68f96
Graphics: Intel HD Graphics 3000, Intel HD Graphics 3000, Built-In, 512 MB
Memory Module: global_name
AirPort: spairport_wireless_card_type_airport_extreme (0x14E4, 0xD6), Broadcom BCM43xx 1.0 5.100.198.104.3)
Bluetooth: Version 2.4.5f1, 2 service, 19 devices, 1 incoming serial ports
Network Service: AirPort, AirPort, en1
Serial ATA Device: TOSHIBA MK7559GSXF, 698,64 GB
Serial ATA Device: MATSHITADVD-R UJ-898
USB Device: FaceTime HD Camera (Built-in), 0x05ac (Apple Inc.), 0x8509, 0xfa200000 / 3
USB Device: Hub, 0x0424 (SMSC), 0x2513, 0xfa100000 / 2
USB Device: BRCM2070 Hub, 0x0a5c (Broadcom Corp.), 0x4500, 0xfa110000 / 5
USB Device: Bluetooth USB Host Controller, 0x05ac (Apple Inc.), 0x821a, 0xfa113000 / 8
USB Device: Apple Internal Keyboard / Trackpad, 0x05ac (Apple Inc.), 0x0245, 0xfa120000 / 4
USB Device: Hub, 0x0424 (SMSC), 0x2513, 0xfd100000 / 2
USB Device: IR Receiver, 0x05ac (Apple Inc.), 0x8242, 0xfd110000 / 3I've had a kenerl panic report with the same characteristics as yours
Interval Since Last Panic Report: 12390 sec
Panics Since Last Report: 3
Anonymous UUID: D4ED497D-32FE-415C-A4AF-2E5D1832321A
Wed Jun 29 22:42:18 2011
panic(cpu 4 caller 0xffffff80002d1208): Kernel trap at 0xffffff800021764b, type 13=general protection, registers:
CR0: 0x000000008001003b, CR2: 0x0000000005c92000, CR3: 0x000000007afea000, CR4: 0x0000000000040660
RAX: 0xffffff800d20d628, RBX: 0x000000000000000e, RCX: 0x0000000005c92000, RDX: 0xffffff809300ba08
RSP: 0xffffff809300b970, RBP: 0xffffff809300ba50, RSI: 0xffff008017546ab8, RDI: 0xffffff809300bb78
R8: 0xffffff809300bc20, R9: 0xffffff809300bc00, R10: 0x0000000000000054, R11: 0x0000000000000000
R12: 0x0000000000000003, R13: 0xffffff800d20d5d0, R14: 0x0000000005c92000, R15: 0x0000000000000000
RFL: 0x0000000000010287, RIP: 0xffffff800021764b, CS: 0x0000000000000008, SS: 0x0000000000000010
Error code: 0x0000000000000000
Backtrace (CPU 4), Frame : Return Address
0xffffff809300b610 : 0xffffff8000204d15
0xffffff809300b710 : 0xffffff80002d1208
0xffffff809300b860 : 0xffffff80002e3f4a
0xffffff809300b870 : 0xffffff800021764b
0xffffff809300ba50 : 0xffffff8000213f1d
0xffffff809300bc60 : 0xffffff80002d0f1e
0xffffff809300bdb0 : 0xffffff80002e3f4a
0xffffff809300bdc0 : 0xffffff80002c8589
0xffffff809300bf60 : 0xffffff800026f1dd
0xffffff809300bf80 : 0xffffff80002742d1
0xffffff809300bfa0 : 0xffffff80002c8527
BSD process name corresponding to current thread: SC2
Mac OS version:
10K540
Kernel version:
Darwin Kernel Version 10.8.0: Tue Jun 7 16:32:41 PDT 2011; root:xnu-1504.15.3~1/RELEASE_X86_64
System model name: MacBookPro8,2 (Mac-94245A3940C91C80)
System uptime in nanoseconds: 902385741897
unloaded kexts:
com.apple.driver.AppleUSBUHCI 4.2.0 (addr 0xffffff7f80963000, size 0x65536) - last unloaded 165246783503
loaded kexts:
com.apple.filesystems.autofs 2.1.0 - last loaded 38484435586
com.apple.driver.AGPM 100.12.31
com.apple.driver.AppleHWSensor 1.9.3d0
com.apple.driver.AudioAUUC 1.57
com.apple.driver.AppleUpstreamUserClient 3.5.7
com.apple.driver.AppleMikeyHIDDriver 1.2.0
com.apple.driver.AppleMCCSControl 1.0.20
com.apple.Dont_Steal_Mac_OS_X 7.0.0
com.apple.driver.AppleMikeyDriver 2.0.5f13
com.apple.kext.ATIFramebuffer 6.3.6
com.apple.driver.AppleIntelHDGraphics 6.3.6
com.apple.driver.AppleHDA 2.0.5f13
com.apple.driver.AudioIPCDriver 1.1.6
com.apple.ATIRadeonX3000 6.3.6
com.apple.driver.SMCMotionSensor 3.0.1d2
com.apple.iokit.AppleBCM5701Ethernet 3.0.5b8
com.apple.driver.AppleGraphicsControl 2.10.6
com.apple.driver.AirPort.Brcm4331 433.11.5
com.apple.driver.ACPI_SMC_PlatformPlugin 4.7.0a1
com.apple.driver.AppleLPC 1.5.1
com.apple.kext.AppleSMCLMU 1.5.2d10
com.apple.driver.AppleIntelSNBGraphicsFB 6.3.6
com.apple.driver.AppleUSBTCButtons 201.6
com.apple.driver.AppleUSBTCKeyboard 201.6
com.apple.driver.AppleIRController 303.8
com.apple.iokit.SCSITaskUserClient 2.6.8
com.apple.iokit.IOAHCIBlockStorage 1.6.4
com.apple.driver.AppleUSBHub 4.2.4
com.apple.driver.AppleSDXC 1.0.3
com.apple.BootCache 31.1
com.apple.AppleFSCompression.AppleFSCompressionTypeZlib 1.0.0d1
com.apple.driver.AppleUSBEHCI 4.2.4
com.apple.driver.AppleEFINVRAM 1.4.0
com.apple.driver.AppleSmartBatteryManager 160.0.0
com.apple.driver.AppleFWOHCI 4.7.3
com.apple.driver.AppleAHCIPort 2.1.7
com.apple.driver.AppleRTC 1.3.1
com.apple.driver.AppleACPIButtons 1.3.6
com.apple.driver.AppleHPET 1.5
com.apple.driver.AppleSMBIOS 1.7
com.apple.driver.AppleACPIEC 1.3.6
com.apple.driver.AppleAPIC 1.4
com.apple.driver.AppleIntelCPUPowerManagementClient 142.6.0
com.apple.security.sandbox 1
com.apple.security.quarantine 0
com.apple.nke.applicationfirewall 2.1.12
com.apple.driver.AppleIntelCPUPowerManagement 142.6.0
com.apple.driver.AppleProfileReadCounterAction 17
com.apple.driver.AppleProfileTimestampAction 10
com.apple.driver.AppleProfileThreadInfoAction 14
com.apple.driver.AppleProfileRegisterStateAction 10
com.apple.driver.AppleProfileKEventAction 10
com.apple.driver.AppleProfileCallstackAction 20
com.apple.iokit.IOSurface 74.2
com.apple.iokit.IOBluetoothSerialManager 2.4.5f3
com.apple.iokit.IOSerialFamily 10.0.3
com.apple.driver.DspFuncLib 2.0.5f13
com.apple.iokit.IOAudioFamily 1.8.3fc2
com.apple.kext.OSvKernDSPLib 1.3
com.apple.driver.AppleSMBusController 1.0.10d0
com.apple.iokit.IOFireWireIP 2.0.3
com.apple.iokit.AppleProfileFamily 41
com.apple.driver.AppleHDAController 2.0.5f13
com.apple.iokit.IOHDAFamily 2.0.5f13
com.apple.iokit.IO80211Family 320.1
com.apple.iokit.IONetworkingFamily 1.10
com.apple.driver.IOPlatformPluginFamily 4.7.0a1
com.apple.driver.AppleSMBusPCI 1.0.10d0
com.apple.driver.AppleBacklightExpert 1.0.1
com.apple.iokit.IONDRVSupport 2.2
com.apple.driver.AppleSMC 3.1.0d5
com.apple.kext.ATI6000Controller 6.3.6
com.apple.kext.ATISupport 6.3.6
com.apple.iokit.IOGraphicsFamily 2.2
com.apple.driver.AppleThunderboltDPOutAdapter 1.3.2
com.apple.driver.AppleThunderboltDPInAdapter 1.3.2
com.apple.driver.AppleThunderboltDPAdapterFamily 1.3.2
com.apple.driver.AppleThunderboltPCIDownAdapter 1.1.6
com.apple.driver.BroadcomUSBBluetoothHCIController 2.4.5f3
com.apple.driver.AppleUSBBluetoothHCIController 2.4.5f3
com.apple.iokit.IOBluetoothFamily 2.4.5f3
com.apple.driver.AppleUSBMultitouch 207.7
com.apple.iokit.IOUSBHIDDriver 4.2.0
com.apple.iokit.IOSCSIMultimediaCommandsDevice 2.6.8
com.apple.iokit.IOBDStorageFamily 1.6
com.apple.iokit.IODVDStorageFamily 1.6
com.apple.iokit.IOCDStorageFamily 1.6.1
com.apple.driver.AppleUSBMergeNub 4.2.4
com.apple.driver.AppleUSBComposite 3.9.0
com.apple.driver.XsanFilter 402.1
com.apple.iokit.IOAHCISerialATAPI 1.2.6
com.apple.iokit.IOSCSIArchitectureModelFamily 2.6.8
com.apple.driver.AppleThunderboltNHI 1.2.6
com.apple.iokit.IOThunderboltFamily 1.4.9
com.apple.iokit.IOUSBUserClient 4.2.4
com.apple.iokit.IOFireWireFamily 4.2.6
com.apple.iokit.IOAHCIFamily 2.0.6
com.apple.iokit.IOUSBFamily 4.2.4
com.apple.driver.AppleEFIRuntime 1.4.0
com.apple.iokit.IOHIDFamily 1.6.6
com.apple.iokit.IOSMBusFamily 1.1
com.apple.security.TMSafetyNet 6
com.apple.kext.AppleMatch 1.0.0d1
com.apple.driver.DiskImages 289.1
com.apple.iokit.IOStorageFamily 1.6.3
com.apple.driver.AppleACPIPlatform 1.3.6
com.apple.iokit.IOPCIFamily 2.6.5
com.apple.iokit.IOACPIFamily 1.3.0
Model: MacBookPro8,2, BootROM MBP81.0047.B0E, 4 processors, Intel Core i7, 2.2 GHz, 4 GB, SMC 1.69f1
Graphics: AMD Radeon HD 6750M, AMD Radeon HD 6750M, PCIe, 1024 MB
Graphics: Intel HD Graphics 3000, Intel HD Graphics 3000, Built-In, 384 MB
Memory Module: global_name
AirPort: spairport_wireless_card_type_airport_extreme (0x14E4, 0xD6), Broadcom BCM43xx 1.0 5.100.198.104.5)
Bluetooth: Version 2.4.5f3, 2 service, 12 devices, 1 incoming serial ports
Network Service: AirPort, AirPort, en1
Serial ATA Device: TOSHIBA MK7559GSXF, 698.64 GB
Serial ATA Device: MATSHITADVD-R UJ-898
USB Device: FaceTime HD Camera (Built-in), 0x05ac (Apple Inc.), 0x8509, 0xfa200000 / 3
USB Device: Hub, 0x0424 (SMSC), 0x2513, 0xfa100000 / 2
USB Device: BRCM2070 Hub, 0x0a5c (Broadcom Corp.), 0x4500, 0xfa110000 / 5
USB Device: Bluetooth USB Host Controller, 0x05ac (Apple Inc.), 0x821a, 0xfa113000 / 8
USB Device: Apple Internal Keyboard / Trackpad, 0x05ac (Apple Inc.), 0x0246, 0xfa120000 / 4
USB Device: Hub, 0x0424 (SMSC), 0x2513, 0xfd100000 / 2
USB Device: IR Receiver, 0x05ac (Apple Inc.), 0x8242, 0xfd110000 / 3
It looks like it is the USB in both our cases -
Help!!! Brand new MBP with Santa Rosa Kernel Panics when started with...
Help!!! Brand new MBP with Santa Rosa Kernel Panics when started with external HD firewire 800 after 20 sec...
I don't know what it could be???
Do you???
Thanx
JayI'm actually having a similar issue and I don't think its related to networking at all.
I'm currently working in a corporate environment where we deploy pre-built OS X images to machines. I recently upgraded my images to 10.4.10 before we got our first Santa Rosa machine. This image was built on a MacPro and worked on all Intel Macs down to a MacMini CoreSolo. When I deployed my prebuilt image to the SR MBP, it caused a kernel panic immediately.
Further investigation revealed previous builds of OS X, including 10.4.10 upgraded from any other model Intel Mac will kernel panic the SR MBP. Going backwards the SR Build of OSX will not work on any previous model Mac, as any other build typically does, but causes severe graphical distortion, as if it does not have the display drivers for the other Macs.
To make a long story short, I think your issue comes from the fact that your external hard drive has an older build of OS X 10.4 than the SR MBP will run (even though you may have upgraded it to 10.4.10). Anyone who can corroborate my story with some more testing, please chime in.
I haven't found a solution for this issue yet other than keeping a seperate Santa Rosa Core 2 Duo image for my deployments. -
Help me decipher a kernel panic
Got hit with a weird kernel panic a few minutes ago. I wasn't doing anything out of the ordinary. Can anybody tell me what's up? Thanks!
panic(cpu 0 caller 0x001A3135): Unresolved kernel trap (CPU 0, Type 14=page fault), registers:
CR0: 0x80010033, CR2: 0x00000000, CR3: 0x00d9f000, CR4: 0x000006e0
EAX: 0x02a91280, EBX: 0x02948535, ECX: 0x00000000, EDX: 0x0041c5c0
CR2: 0x00000000, EBP: 0x1428bce8, ESI: 0x03a2c900, EDI: 0x02a81f80
EFL: 0x00010202, EIP: 0x00000000, CS: 0x00000008, DS: 0x00000010
Backtrace, Format - Frame : Return Address (4 potential args on stack)
0x1428bb08 : 0x128d1f (0x3c9540 0x1428bb2c 0x131df4 0x0)
0x1428bb48 : 0x1a3135 (0x3cf1f4 0x0 0xe 0x3cea24)
0x1428bc58 : 0x19a8d4 (0x1428bc64 0xe 0x14280048 0x3c0010)
0x1428bce8 : 0x3bd052 (0x2a81f80 0x3a2c900 0x3ed758 0x3c1a00)
0x1428bd18 : 0x3b1f5c (0x2a79800 0x3a2c900 0x2ab2c04 0x19d23a)
0x1428bd78 : 0x188e25 (0x2ab2c00 0x3a3a2ac 0x3a081b4 0x3a081c8)
0x1428bdb8 : 0x12b4da (0x3a3a284 0x3a08198 0x0 0x0)
0x1428bdf8 : 0x124b2b (0x3a3a200 0x0 0x48 0x1428bedc)
0x1428bf08 : 0x1955a1 (0x1428bf44 0x0 0x0 0x0)
0x1428bfc8 : 0x19ad4e (0x2d5f078 0x0 0x19d0b5 0x2667c64) No mapping exists for frame pointer
Backtrace terminated-invalid frame pointer 0xbfffe348
Kernel version:
Darwin Kernel Version 8.8.1: Mon Sep 25 19:42:00 PDT 2006; root:xnu-792.13.8.obj~1/RELEASE_I386
Model: MacBookPro1,1, BootROM MBP11.0055.B03, 2 processors, Intel Core Duo, 2.16 GHz, 1 GB
Graphics: ATI Radeon X1600, ATY,RadeonX1600, PCIe, 256 MB
Memory Module: BANK 1/DIMM1, 1 GB, DDR2 SDRAM, 667 MHz
AirPort: spairportwireless_card_type_airportextreme (0x168C, 0x86), 0.1.27
Bluetooth: Version 1.7.9f12, 2 service, 0 devices, 1 incoming serial ports
Network Service: AirPort, AirPort, en1
Serial ATA Device: ST9120821AS, 111.79 GB
Parallel ATA Device: MATSHITADVD-R UJ-857
USB Device: Built-in iSight, Micron, Up to 480 Mb/sec, 500 mA
USB Device: Apple Internal Keyboard / Trackpad, Apple Computer, Up to 12 Mb/sec, 500 mA
USB Device: Bluetooth HCI, Up to 12 Mb/sec, 500 mA
USB Device: IR Receiver, Apple Computer, Inc., Up to 12 Mb/sec, 500 mAThat's often caused by "bad" third party RAM, but, by the look of your report, it only has a 1GB Apple stick in it?
When did you last "Repair Permissions"? -
Disk order changes, grub problem, filesystem check failed
I'm having some problems installing Archlinux onto a machine with a lot of SATA drives, some connected by SATA cards. I have tried the 2009-08 netinstaller burned to CD, both -x86_64.iso and -x86_64-isolinux.iso, and I have the same problem with both.
I am installing from a USB-connect optical drive to an Intel X25-M 80GB SSD connected to a motherboard SATA port. I also have 2 HDDs connected to motherboard SATA ports, and 4 more HDDs connected to 4 SIL-based PCIe SATA cards. Additionally, I have a 4GB Patriot USB flash drive connected to a motherboard USB port. None of the HDDs have a bootable MBR, I am planning to create an mdadm RAID with the HDDs, but the USB flash drive is bootable. The motherboard is an Asus Z8PE-D18 with the latest BIOS, in AHCI mode.
First thing to note is that I was able to successfully install Fedora 12 linux to this machine in the exact configuration that I am trying to install Archlinux. I just installed Fedora 12 again last night, and it installed and loaded fine when I rebooted from the SSD.
So, the problems I am having with Archlinux. During install, I found that the SSD is showing up as either /dev/sde or /dev/sdf. This is odd since it was /dev/sda with Fedora. It makes sense for it to be /dev/sda, since it is on the first motherboard SATA port. But I proceeded with the Archlinux install, and grub seemed to detect the stage1 location properly -- root was set to (hda4,0) or (hda5,0) depending on whether the SSD was at sde or sdf. The kernel root was configured by UUID, so that does not depend on the drive order. Okay so far.
The problem shows up on reboot. The bootloader immediately complains that there is no such partition sde1 or sdf1. I drop into a grub command line and do
find /boot/grub/stage1
and it replies with (hd0,0), so I modify the boot line to root (hd0,0) and boot. Now it gets pretty far. Lots of boot messages scroll by. Here are some of the last few before the problem:
Waiting 10 seconds for device /dev/disk/by-uuid/22a35aa2-9799-4575-b1eb-456e819a1a26 ...
kjournald starting. Commit interval 5 seconds
EXT3-fs (sde1): mounted filesystem with writeback data mode
INIT: version 2.86 booting
::Starting UDev DAemon
::Triggering UDev uevents
::Loading Modules
::Waiting for UDev uevents to be processed
::Bringing up loopback interface
::Mounting Root Read-only
::Checking Filesystems
/dev/sdf1:
The superblock could not be read or does not describe a correct ext2
filesystem. If the device is valid and it really contains an ext2
filesystem (and not swap or ufs or something else), then the superblock
is corrupt, and you might try running e2fsck with an alternate superblock
**** FILESYSTEM CHECK FAILED
* Please repair manually and reboot. Note that the root file system
* is currently mounted read-only....
Give root password for maintenance
So I logged in as root and did an fdisk -l. The boot SSD was at /dev/sde. The menu.lst has root as (hd5,0), which would be sdf (which was correct during installation, but the disk order apparently changed). The kernel root= in menu.lst used by-uuid, and it at least points to the correct drive, which I suppose is why I was able to boot as far as I did, but when it tries to mount the root filesystem, it fails as shown above.
So, at initial grub boot, the grub stage1 is found at (hd0,0). During installation, the SSD was sdf, but after booting the kernel, the SSD is sde. What is going on?
One other experiment is that I pulled all the drives (including USB flash drive) except the SSD. The HDDs are in hot-swap slots, so that was easy. The PCIe SATA cards are still plugged into the PCIe slots. Then I was able to successfully install and boot Archlinux. But when I plugged the drives back in and rebooted, I had the same problem as detailed above.
Any suggestions on how to fix this?I had the same problem.
Last week I installed Arch onto a new SATA HD. I wanted to make sure the installation worked before I attached the other drives. On booting with the other drives attached, similar messages.
My solution:
Login as root.
Follow the instruction to mount / as read-write so you can make changes to the filesystem.
edit /etc/fstab and eliminate the references to /dev/sdxx and replace them with UUIDs or labels (as suggested above) as these won't change.
in /etc/fstab ...
# external data sources
#data /dev/sdb6
UUID=931d7107-1241-4d82-ad28-fcbe7af8ba69 /data ext3 defaults 0 0
#Documents /dev/sda9
/dev/disk/by-label/Documents /data/Documents ext3 defaults 0 0
Reboot and you should be good.
You can find the UUID of the drives by using
$ blkid
or you can set a drive label with e2label, assuming you are using ext2,3 or 4
Good luck. -
Filesystem check failed. with UUID, SATA, fsck -f doesn't res [SOLVED]
It appeared right on the first boot.
Things I tried:
reinstalled Arch
fsck -f
checked fstab - all mountpoints in UUID
system was installed with AHCPI enabled and running
system boots like this:
Bringing up loopback interface [done]
Mounting Root Read-only [done]
Checking Filesystems [busy] linuxroot: clean, 110927/327680 files, 744572/1310384 blocks
[fail]
Filesystem check failed.
Please repair manually and reboot. Note that the root file system is currently mounted readonly. To remount it read-write type: mount -n -o remount ,rw /
When you exit the maintenance shell the system will reboot automatically.
Its a Sata-HD
It has 4 partitions and had Vista preinstalled using the first 3. on the last patitions (sda4) i put /. home and swap are on a USB-HD
EDIT
fstab
# /etc/fstab: static file system information
# <file system> <dir> <type> <options> <dump> <pass>
devpts /dev/pts devpts defaults 0 0
shm /dev/shm tmpfs nodev,nosuid 0 0
#/dev/cdrom /media/cd auto ro,user,noauto,unhide 0 0
#/dev/dvd /media/dvd auto ro,user,noauto,unhide 0 0
#/dev/fd0 /media/fl auto user,noauto 0 0
UUID=3f247afa-7966-4472-aea3-d65199b769b3 swap swap defaults 0 0
UUID=735b5356-141f-4ee5-a5cf-4ca82dd6809b /home ext3 defaults,noatime 0 1
UUID=cc6b9a82-b403-4fce-94b7-a939e85fbd17 / ext3 defaults,noatime 0 1
Last edited by capoeira (2010-05-27 21:03:23)Factory wrote:Are you positive those are the correlating uuids for the appropriate drives? On my desktop my sd*#s like to switch themselves after an install.
yes, the UUIDs were generated by the installer, and I can manualy mount them with "mount /dev/sda4", "mount /dev/sdb2"
EDIT: I duble checked that, UUIDs OK
Inxsible wrote:
capoeira wrote:It has 4 partitions and had Vista preinstalled using the first 3. on the last patitions (sda4) i put /. home and swap are on a USB-HD
Probably a dumb question, but you do have your USB HD plugged in when you boot up, right?
sure I do
Last edited by capoeira (2010-05-27 18:39:28) -
Today I upgrade the kernel to 2.6.19,but when I reboot it,I get such information:
/dev/sda3
The superblock could not be read or does not describe a correct ext2
filesystem. If the device is valid and it really contains an ext2
filesystem (and not swap or ufs or something else). then the superblock
is corrupt,and you might try running e2fsck with an alternate superblock:
e2fsck -b 8193 <device>
[FAIL]
*********************FILESYSTEM CHECK FAILED **************
* Please repair manually and reboot. Note that the root *
* file system is currently mounted read-only.To remount *
* it read write type: mount -n -o remount,rw / *
* When you exit the maintenance shell the system will *
* reboot automatically. *
Press enter for maintenance
(or type Control D to continue)
[root@(none)~]# cd /
[root@(none) /]# mount -n -o remount,rw /
mount:invalid option -n
[root@(none) /]# _
The above information is from my vmware-station,and in my own linux system I got the same,what should I do?
Can I use a livecd to mkinitcpio to rescue the system?I just realized that now the file system error happens before udev has even started and then it drops me into maintenence mode... I can't do e2fsck or mkfs.ext3 -n /dev/sda7 because the corresponding device node doesn't exist yet... The only nodes were console, null, and a third one but I forget...
My grub and fstab seem to be correct (I just verified and they worked before)... Any help please (having the /dev/sda7 node would be nice as I can't do anything without it)? I'm using an Intel chipset and I've tried various combinations of pata/ide/piix/etc in my mkinitcpio.conf (and generated the images of course)...
I'm still searching through gentoo forums (I've tried everything I could find in arch forums) -- The partition seems also to be intact as it is accessible to me with livecd (I even chrooted and pacman -Syu) and through ext2ifs w/ vi on my Windows 2003 partition...
Thanks -
[Solved (initscripts-splash plroblem)] Filesystem check failed
Hello, my arch i686 sudently doesn't boot.
At system start, after loading kernel, the boot process stops and says "FILESYSTEM CHECK FAILED" give root password for maintenance or control+D for restart.
My root partition (dev/sda2) is reiserfs formated, and arch updated this week.
After reading a while I booted with Arch install CD and tried the follwing:
fsck.reiserfs --check /dev/sda2
fsck.reiserfs --fix-fixable /dev/sda2
fsck.reiserfs --rebuild-sb /dev/sda2
fsck.reiserfs --clean-attributes /dev/sda2
But no errors were found or fixed, so I can't boot arch yet.
Are there any other way to fix the filesystem?
can filesystem check be skipped?
please help
Last edited by juan_sck (2008-10-13 11:09:17)Mektub wrote:
Could it be that it is anoter partition that is giving trouble ? Ot do you only have /dev/sda2 ?
Or start in sinle-user. At the grub boot menu, select the option that lets you edit the kernel parameters.
Add either a '1' or 'single' to the end of the kernel parameters, then continue booting up.
Mektub
of course I know where I installled Arch.
pointone wrote:There should be a more descriptive error message above where it says "filesystem check failed" describing WHY the fsck failed.
No, just system check failed. Even more, my filesystem was perfectly, it was a problem with initscripts-splash
iDeJ wrote:
i had a similar problem after the last pacman -Syu, basicly the bootsplash-initscripts are not compatible with latest udev
maybe it helps
http://bbs.archlinux.org/viewtopic.php?id=56604
I don't think installing a year old initscripts package would solve it, but you were very helpful.
Finally I could solve it with the recovery console:
After the error message I typed root password to log in, then remounted root partition for r/w:
mount -n -o remount,rw /
Finally I had to remove the package initscripts-splash and install initscripts form core.
ifconfig eth0 up
dhcpcd eth0
pacman -Syu
pacman -Rs initscripts-splash
pacman -S initscripts
exit
**You should make a backup of rc.conf before installing initscripts, because installing initscrips will overwrite it (and a few other files i hadn't modified), and pacman was supoussed to back it up, but it didn't
thanks for your help. -
Filesystem check failed + accidental /boot deletion
Yesterday I rebooted my PC and suddenly Arch started complaining about "Filesystem check failed", just like stated by the OP in this thread https://bbs.archlinux.org/viewtopic.php … 00#p941200
The problem was with two partitions: /boot and /home. I tried to no avail to manually fsck them using the maintenance console and e2fsck as well as the forcefsck command but it didn't work.
I didn't try any LiveCD back then but since I saw that in that thread the OP solved his problem by deleting some folders located at /media:
Fixed the problem.
The /dev/sda2 and /dev/sda5 were being mounted in the wrong place.
Instead of being mounted in /home and /boot as per /etc/fstab, they were being mounted in new directories in /media called /media/usbhd-sda2 and /media/usbhd-sda5. Upon deleting those folders, everything has gone back to normal.
I have no idea how those new folders got created...but problem solved now.
Thanks for the help, guys
Samsom
Problem is I didn't think at all when I read this post and went right away to delete the problematic folders (the post itself didn't exactly explain how the OP managed to unmount the partitions and then proceed to delete the folders, my umount commands didn't work so it wasn't crystal clear to me how he managed it, my bad tho for not checking what I was deleting).
Luckily, I think I only managed to delete partially my /boot folder (thus GRUB now complains and doesn't boot any system). So now my question is, is there a way to restore my /boot folder without a full system re-install?
Thanks in advance.But what is the command? mkinitcpio -p kernel26 ? Also how do I fix this grub issue? I'm assuming grub created a default menu.lst after I copied the config files and setup the hd0 but I actually don't recall checking that.
Just re-did all steps including rebuilding the kernel, I still can't get the boot menu when I reboot. It goes directly to grub console.
I checked the generated menu.lst, it lists my root as the device where /boot partition is and the kernel line root enrty is defined for the arch system I want to boot :\
Last edited by Grimn (2011-05-31 17:50:02) -
"FILESYSTEM CHECK FAILED" - fresh install, clean partition
Hi,
I just installed Arch on my Asus EEE 701SD. Since GRUB is extremely slow (takes about 30-45 seconds from "loading..." to menu) I've set up my /boot on a separate flash drive. However, booting the new installation gives me the "FILESYSTEM CHECK FAILED" + maintenance shell. I've tried running fsck with various options but none of it has helped. Apparently, the partition is clean so I'm not quite sure what's going on. Any suggestions?
Cheers:)The hook "usb" should work too, so I don't think we're on the right track here. But since it doesn't hurt you can add the actual kernel modules to the modules= line:
usbcore ehci-hcd (and/or uhci-hcd) usb-storage and maybe the filesystem used (and it's dependencies like ciphers).
Greets,
demian
// I guess I'm a slow typer. Why don't you show us your /etc/fstab?
From what you've written the system shouldn't be able to boot since there's no fstab entry for /boot. Maybe I misunderstood you.
Last edited by demian (2010-06-07 23:00:48) -
Filesystem check failed, but filesystems are clean
Im running custom kernel and this might be related to it, but Im on my wits' end here and looking for pointers.
The problem is, Im getting filesystem check failed every time I boot my system. And it gives no apparent reason
for it to happen. I have fsck'd my partitions many times and they are clean. My hwclock is in time and rc.conf is set
to 'localtime'. The problem didn't occurs on the previous kernel (2.6.18) I had, so I've been using its running config to
compile the new one (2.6.23). The thing is, the previous kernel works fine, no filesystem check failed in boot. Only
difference between those two is I had to enable HOTPLUG in the newer kernel to get udev working, otherwise it would
complain about failing netlink socket in initscript.
As a temporary solution, I commented out the filesystem check from the rc.sysinit and it boots further. This time
it fails to mount my /boot/ and /home/ directory and fails to activate my swap. Effectively only root is mounted, but
after logging in, "mount -a" works without any problems and I can use my system normally.
I have compiled all(?) the needed modules to the kernel, so initramfs shouldn't be needed, but I've tried it anyway, no
luck there. The system is build with 2009.08 core install disc, no packages updated as far as I recall.
fstab:
#none /dev/pts devpts defaults 0 0
#none /dev/shm tmpfs defaults 0 0
/dev/hdb /media/cdrom auto ro,user,noauto,unhide 0 0
#/dev/dvd /media/dvd auto ro,user,noauto,unhide 0 0
#/dev/fd0 /media/fl auto user,noauto 0 0
/dev/disk/by-uuid/728c65f2-a84f-401f-9899-17020758b829 /boot ext3 defaults 0 1
/dev/disk/by-uuid/2767f772-203a-4fe9-ac4d-7c8754abc4c8 swap swap defaults 0 0
/dev/disk/by-uuid/b0b958c4-5f24-414a-8826-6df956f0815b / reiserfs defaults 0 1
/dev/disk/by-uuid/e83b7114-86fe-4e8f-9e95-0d92b8e50d1a /home reiserfs defaults 0 1
dmesg:
Linux version 2.6.23-xbox (root@xbox) (gcc version 4.1.2) #3 Sat Oct 2 14:20:54 EEST 2010
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f000 (usable)
BIOS-e820: 000000000009f000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000003c00000 (usable)
BIOS-e820: 0000000003c00000 - 0000000004000000 (reserved)
60MB LOWMEM available.
Entering add_active_range(0, 0, 15360) 0 entries of 256 used
Zone PFN ranges:
DMA 0 -> 4096
Normal 4096 -> 15360
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0 -> 15360
On node 0 totalpages: 15360
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4064 pages, LIFO batch:0
Normal zone: 88 pages used for memmap
Normal zone: 11176 pages, LIFO batch:1
Movable zone: 0 pages used for memmap
DMI not present or invalid.
Allocating PCI resources starting at 10000000 (gap: 04000000:fc000000)
Built 1 zonelists in Zone order. Total pages: 15240
Kernel command line: root=/dev/hda3 devfs=mount kbd-reset xbox=hdd
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 256 (order: 8, 1024 bytes)
Detected 733.370 MHz processor.
Console: colour dummy device 80x25
console [tty0] enabled
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 57652k/61440k available (1764k kernel code, 3380k reserved, 470k data, 136k init, 0k highmem)
virtual kernel memory layout:
fixmap : 0xffffb000 - 0xfffff000 ( 16 kB)
vmalloc : 0xc4800000 - 0xffff9000 ( 951 MB)
lowmem : 0xc0000000 - 0xc3c00000 ( 60 MB)
.init : 0xc0332000 - 0xc0354000 ( 136 kB)
.data : 0xc02b90ae - 0xc032ea60 ( 470 kB)
.text : 0xc0100000 - 0xc02b90ae (1764 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 1467.98 BogoMIPS (lpj=2935965)
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0383f9ff 00000000 00000000 00000000 00000000 00000000 00000000 00000000
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 128K
CPU: After all inits, caps: 0383f9ff 00000000 00000000 00000040 00000000 00000000 00000000 00000000
Compat vDSO mapped to ffffe000.
CPU: Intel Celeron (Coppermine) stepping 0a
Checking 'hlt' instruction... OK.
NET: Registered protocol family 16
PCI: Using configuration type 1
Setting up standard PCI resources
SCSI subsystem initialized
libata version 2.21 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
PCI: Cannot allocate resource region 7 of bridge 0000:00:08.0
PCI: Cannot allocate resource region 8 of bridge 0000:00:08.0
PCI: Cannot allocate resource region 9 of bridge 0000:00:08.0
PCI: Bridge: 0000:00:08.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Failed to allocate mem resource #2:80000@f8000000 for 0000:01:00.0
PCI: Failed to allocate mem resource #6:10000@f8000000 for 0000:01:00.0
PCI: Bridge: 0000:00:1e.0
IO window: disabled.
MEM window: fd000000-fdffffff
PREFETCH window: f0000000-f7ffffff
PCI: Setting latency timer of device 0000:00:08.0 to 64
NET: Registered protocol family 2
Time: tsc clocksource has been installed.
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
checking if image is initramfs... it is
Freeing initrd memory: 325k freed
Enabling Xbox eject problem workaround.
fuse init (API version 7.8)
io scheduler noop registered
io scheduler deadline registered (default)
io scheduler cfq registered
xboxfb: nVidia device/chipset 10DE02A0
xboxfb: Detected 64MB of system RAM
xboxfb: Using 4M framebuffer memory
i2c-xbox.o version 0.0.1
i2c-xbox.o: Found nVidia XBOX nForce SMBus controller.
i2c-xbox.o: SMBus bus detected and initialized
xbox-tv-i2c: Using 'SMBus adapter at c000'!
xboxfb: Setting TV mode from EEPROM (NTSC)
xboxfb: detected conexant encoder
xboxfb: Setting cable type from AVIP ID: HDTV (Component video)
xboxfb: RIVA MTRR set to ON
Console: switching to colour frame buffer device 80x30
xboxfb: PCI nVidia NV20 framebuffer ver 0.9.5b-xbox (XboxGeForce3, 4MB @ 0xF3C00000)
Real Time Clock Driver v1.12ac
Linux agpgart interface v0.102
[drm] Initialized drm 1.1.0 20060810
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: module loaded
forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.60.
PCI: Setting latency timer of device 0000:00:04.0 to 64
eth0: forcedeth.c: subsystem: 00000:0000 bound to 0000:00:04.0
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
NFORCE: IDE controller at PCI slot 0000:00:09.0
NFORCE: chipset revision 212
NFORCE: not 100% native mode: will probe irqs later
NFORCE: 0000:00:09.0 (rev d4) UDMA100 controller
ide0: BM-DMA at 0xff60-0xff67, BIOS settings: hda:DMA, hdb:DMA
Probing IDE interface ide0...
hda: WDC WD2500JB-00FUA0, ATA DISK drive
hdb: PHILIPS XBOX DVD DRIVE, ATAPI CD/DVD-ROM drive
hda: host side 80-wire cable detection failed, limiting max speed to UDMA33
hda: selected mode 0x42
hdb: selected mode 0x42
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hda: max request size: 512KiB
hda: 488397168 sectors (250059 MB) w/8192KiB Cache, CHS=30401/255/63, UDMA(33)
hda: cache flushes supported
hda: hda1 hda2 hda3 hda4
hdb: ATAPI DVD-ROM drive, 128kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
PCI: Setting latency timer of device 0000:00:02.0 to 64
ohci_hcd 0000:00:02.0: OHCI Host Controller
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:02.0: irq 1, io mem 0xfed00000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
PCI: Setting latency timer of device 0000:00:03.0 to 64
ohci_hcd 0000:00:03.0: OHCI Host Controller
ohci_hcd 0000:00:03.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:03.0: irq 9, io mem 0xfed08000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
USB Universal Host Controller Interface driver v3.0
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
usb 1-3: new low speed USB device using ohci_hcd and address 2
usb 1-3: configuration #1 chosen from 1 choice
input: DELL DELL USB Keyboard as /devices/pci0000:00/0000:00:02.0/usb1/1-3/1-3:1.0/input/input0
usbcore: registered new interface driver usbkbd
drivers/hid/usbhid/usbkbd.c: :USB HID Boot Protocol keyboard driver
usbcore: registered new interface driver usbmouse
drivers/hid/usbhid/usbmouse.c: v1.6:USB HID Boot Protocol mouse driver
TCP cubic registered
drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
Freeing unused kernel memory: 136k freed
ReiserFS: hda3: found reiserfs format "3.6" with standard journal
ReiserFS: hda3: using ordered data mode
ReiserFS: hda3: journal params: device hda3, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hda3: checking transaction log (hda3)
ReiserFS: hda3: Using r5 hash to sort names
NET: Registered protocol family 1
spurious 8259A interrupt: IRQ7.
udev: starting version 141
df -h after "mount -a":
Filesystem Size Used Avail Use% Mounted on
/dev/disk/by-uuid/b0b958c4-5f24-414a-8826-6df956f0815b
7.4G 2.1G 5.3G 29% /
/dev/hda1 99M 11M 83M 12% /boot
/dev/hda4 226G 39M 226G 1% /home
Ok, something is definately wrong there, only root is by-uuid
blkid:
/dev/hda3: UUID="b0b958c4-5f24-414a-8826-6df956f0815b" TYPE="reiserfs"
/dev/hda2: TYPE="swap" UUID="2767f772-203a-4fe9-ac4d-7c8754abc4c8"
/dev/hda4: UUID="e83b7114-86fe-4e8f-9e95-0d92b8e50d1a" TYPE="reiserfs"
/dev/hda1: UUID="728c65f2-a84f-401f-9899-17020758b829" SEC_TYPE="ext2" TYPE="ext3"
Should I try newer udev? Can I even use the latest with 2.6.23?Mounting Local Filesystems fails
Mount: Special device /dev/disk/by-uuid/728c65f2-a84f-401f-9899-17020758b829 does not exist
Mount: Special device /dev/disk/by-uuid/e83b7114-86fe-4e8f-9e95-0d92b8e50d1a does not exist
so does Activating swap.
still, ls -la /dev/disk/by-uuid/ gives me:
lrwxrwxrwx 1 root root 10 2010-10-02 22:45 2767f772-203a-4fe9-ac4d-7c8754abc4c8 -> ../../hda2
lrwxrwxrwx 1 root root 10 2010-10-02 22:45 728c65f2-a84f-401f-9899-17020758b829 -> ../../hda1
lrwxrwxrwx 1 root root 10 2010-10-02 22:45 b0b958c4-5f24-414a-8826-6df956f0815b -> ../../hda3
lrwxrwxrwx 1 root root 10 2010-10-02 22:45 e83b7114-86fe-4e8f-9e95-0d92b8e50d1a -> ../../hda4
should I have /boot and /home in /dev?
Full system upgrade gave me the same issue. Even after udev downgrade (udev-142 is the latest I can use with 2.6.23).
Edit:
Changed my fstab back from by-uuid to hdaX, didn't help. Strangely all hdaX are in /dev/ after boot, but the symlinks are missing.
Last edited by TelaKeppi (2010-10-02 21:22:53) -
"FILESYSTEM CHECK FAILED" after pacman -Syu
Hi all,
After a sucessfull 'pacman -Syu' (in which i didnt see any 'todo' messages but it did have a kernel upgrade) archlinux cannot start and i just get to a message similar talking about my root partition (ext3):
The superblock could not be read or does not describe a correct ext2
filesystem. If the device is valid and it really contains an ext2
filesystem (and not swap or ufs or something else), then the superblock
is corrupt, and you might try running e2fsck with an alternate superblock:
e2fsck -b 8193 <device>
******************* FILESYSTEM CHECK FAILED *************
* Please repair manually and reboot. Note that the root *
* filesystem is currently mounted read-only. To remount *
* it read-write type: mount -n -o remount,rw / *
* When you exit the mantenance shel the system will *
* reboot automatically. *
I restarted with a livecd and 'e2fscked' the partition (which btw found many errors that were corrected by it) but archlinux still gives me the same message. I have checked the partition again and again a thousand times but it always comes up clean, im even able to mount it from the different livecds i have tried and can read and create files on it so im pretty sure it is fine.
And so my question is, does anyone know why this is happening? How comes archlinux keeps seeing a problem in this partition when others dont? What am i doing wrong?
An y answer appreciated.
Last edited by feralert (2009-06-03 20:15:23)Hi again,
I have done some testing, maybe it will help.
After the failure message i put roots password and i got dropped to a shell, if i try to find the root partition (eg. ls /dev/sda) gives an error cause it sda doesnt exists.
If i edit rc.sysinit with a livecd and remove the fsck part i get a few diferent errors, some about partitions not being found and similar stuff. In my little knowledge of linux it ooks to me like it doesnt load the sata module or somethig...
I copy here the pacman.log file, i remember that the update was a huge one, around 400 Mbytes if i remember correctly:
[2009-05-30 22:20] synchronizing package lists
[2009-05-30 22:21] starting full system upgrade
[2009-05-30 22:23] synchronizing package lists
[2009-05-30 22:23] starting full system upgrade
[2009-05-30 23:29] upgraded alacarte (0.11.10-1 -> 0.12.1-1)
[2009-05-30 23:29] upgraded kernel-headers (2.6.27.6-2 -> 2.6.29.3-1)
[2009-05-30 23:29] upgraded tzdata (2009f-1 -> 2009g-1)
[2009-05-30 23:29] warning: /etc/locale.gen installed as /etc/locale.gen.pacnew
[2009-05-30 23:29] Generating locales...
[2009-05-30 23:29] es_ES.UTF-8... done
[2009-05-30 23:29] es_ES.ISO-8859-1... done
[2009-05-30 23:29] es_ES.ISO-8859-15@euro... done
[2009-05-30 23:29] Generation complete.
[2009-05-30 23:29] upgraded glibc (2.9-4 -> 2.10.1-2)
[2009-05-30 23:29] upgraded alsa-lib (1.0.19-1 -> 1.0.20-1)
[2009-05-30 23:29] upgraded alsa-utils (1.0.19-1 -> 1.0.20-1)
[2009-05-30 23:29] upgraded binutils (2.19.1-1 -> 2.19.1-3)
[2009-05-30 23:29] upgraded geoip (1.4.5-1 -> 1.4.6-1)
[2009-05-30 23:29] upgraded gcc-libs (4.3.3-1 -> 4.4.0-2)
[2009-05-30 23:29] upgraded libdrm (2.4.9-1 -> 2.4.11-2)
[2009-05-30 23:29] upgraded libgl (7.4.1-1 -> 7.4.2-2)
[2009-05-30 23:29] upgraded mesa (7.4.1-1 -> 7.4.2-1)
[2009-05-30 23:29] upgraded wxgtk (2.8.9.2-1 -> 2.8.10-1)
[2009-05-30 23:29] upgraded amule (2.2.4-1 -> 2.2.5-2)
[2009-05-30 23:29] upgraded x264 (20090216-1 -> 20090416-1)
[2009-05-30 23:29] upgraded avidemux (2.4.4-2 -> 2.4.4-3)
[2009-05-30 23:29] upgraded bin86 (0.16.17-3 -> 0.16.17-4)
[2009-05-30 23:29] upgraded gmp (4.2.4-1.1 -> 4.3.1-2)
[2009-05-30 23:29] upgraded coreutils (7.2-1 -> 7.4-1)
[2009-05-30 23:29] upgraded dbus-core (1.2.4.4permissive-1 -> 1.2.14-1)
[2009-05-30 23:29] upgraded glib2 (2.20.1-1 -> 2.20.2-1)
[2009-05-30 23:29] upgraded bluez (4.37-1 -> 4.39-1)
[2009-05-30 23:29] upgraded gstreamer0.10 (0.10.22-1 -> 0.10.23-1)
[2009-05-30 23:29] upgraded gstreamer0.10-base (0.10.22-1 -> 0.10.23-1)
[2009-05-30 23:29] upgraded gstreamer0.10-base-plugins (0.10.22-1 -> 0.10.23-1)
[2009-05-30 23:29] upgraded brasero (2.26.1-2 -> 2.26.2-1)
[2009-05-30 23:29] upgraded policykit (0.9-7 -> 0.9-9)
[2009-05-30 23:29] upgraded consolekit (0.3.0-3 -> 0.3.0-5)
[2009-05-30 23:29] upgraded cpio (2.9-3 -> 2.9-5)
[2009-05-30 23:29] upgraded curl (7.19.4-1 -> 7.19.5-2)
[2009-05-30 23:29] upgraded dbus (1.2.4.4permissive-1 -> 1.2.14-1)
[2009-05-30 23:29] upgraded dcron (3.2-3 -> 3.2-4)
[2009-05-30 23:29] upgraded dhcpcd (4.0.12-1 -> 5.0.4-1)
[2009-05-30 23:29] upgraded dmapi (2.2.9-1 -> 2.2.10-1)
[2009-05-30 23:29] upgraded docbook-xml (4.5-1 -> 4.5-2)
[2009-05-30 23:29] upgraded gconf (2.26.0-3 -> 2.26.2-1)
[2009-05-30 23:29] upgraded gnome-desktop (2.26.1-1 -> 2.26.2-1)
[2009-05-30 23:29] upgraded gdbm (1.8.3-5 -> 1.8.3-6)
[2009-05-30 23:29] upgraded sqlite3 (3.6.13-1 -> 3.6.14.1-1)
[2009-05-30 23:29] upgraded python (2.6.1-1 -> 2.6.2-1)
[2009-05-30 23:29] upgraded eog (2.26.1-1 -> 2.26.2-1)
[2009-05-30 23:30] upgraded epiphany (2.26.1-1 -> 2.26.2-1)
[2009-05-30 23:30] upgraded poppler (0.10.6-1 -> 0.10.7-1)
[2009-05-30 23:30] upgraded poppler-glib (0.10.6-1 -> 0.10.7-1)
[2009-05-30 23:30] upgraded evince (2.26.1-1 -> 2.26.2-1)
[2009-05-30 23:30] upgraded libsoup (2.26.1-1 -> 2.26.2-1)
[2009-05-30 23:30] upgraded evolution-data-server (2.26.1.1-1 -> 2.26.2-1)
[2009-05-30 23:30] upgraded ffmpeg (20090217-1 -> 0.5-1)
[2009-05-30 23:30] upgraded file (5.00-1 -> 5.03-2)
[2009-05-30 23:30] upgraded file-roller (2.26.1-1 -> 2.26.2-1)
[2009-05-30 23:30] upgraded findutils (4.4.0-1 -> 4.4.1-2)
[2009-05-30 23:30] upgraded gcalctool (5.26.1-1 -> 5.26.2-1)
[2009-05-30 23:30] installed ppl (0.10.2-2)
[2009-05-30 23:30] installed cloog-ppl (0.15.3-1)
[2009-05-30 23:30] upgraded gcc (4.3.3-1 -> 4.4.0-2)
[2009-05-30 23:30] upgraded gtksourceview2 (2.6.1-1 -> 2.6.2-1)
[2009-05-30 23:30] upgraded gedit (2.26.1-1 -> 2.26.2-1)
[2009-05-30 23:30] upgraded glproto (1.4.9-1 -> 1.4.10-1)
[2009-05-30 23:30] upgraded gnome-games (2.26.1-1 -> 2.26.2-1)
[2009-05-30 23:30] upgraded whois (4.7.33-1 -> 4.7.33-2)
[2009-05-30 23:30] upgraded gnome-nettool (2.26.1-1 -> 2.26.2-1)
[2009-05-30 23:30] upgraded policykit-gnome (0.9.2-3 -> 0.9.2-4)
[2009-05-30 23:30] upgraded gnome-panel (2.26.1-1 -> 2.26.2-1)
[2009-05-30 23:31] upgraded gnome-power-manager (2.26.1-1 -> 2.26.1-2)
[2009-05-30 23:31] upgraded vte (0.20.1-1 -> 0.20.2-1)
[2009-05-30 23:31] upgraded gnome-terminal (2.26.1-1 -> 2.26.2-2)
[2009-05-30 23:31] upgraded gtk-engines (2.18.1-1 -> 2.18.2-1)
[2009-05-30 23:31] upgraded gnome-themes (2.26.1-1 -> 2.26.2-1)
[2009-05-30 23:31] upgraded gnome2-user-docs (2.26.1-1 -> 2.26.2-1)
[2009-05-30 23:31] upgraded gparted (0.4.4-2 -> 0.4.5-1)
[2009-05-30 23:31] upgraded gstreamer0.10-bad (0.10.11-1 -> 0.10.12-1)
[2009-05-30 23:31] upgraded libraw1394 (1.3.0-2 -> 2.0.2-1)
[2009-05-30 23:31] installed libusb1 (1.0.0-1)
[2009-05-30 23:31] upgraded libdc1394 (2.0.3-1 -> 2.1.0-1)
[2009-05-30 23:31] upgraded libdvdread (0.9.7-2 -> 4.1.3-1)
[2009-05-30 23:31] upgraded libdvdnav (0.1.10-3 -> 4.1.3-1)
[2009-05-30 23:31] upgraded neon (0.28.3-2 -> 0.28.4-1)
[2009-05-30 23:31] installed liblrdf (0.4.0-6)
[2009-05-30 23:31] upgraded gstreamer0.10-bad-plugins (0.10.11-3 -> 0.10.12-1)
[2009-05-30 23:31] upgraded gstreamer0.10-good (0.10.14-1 -> 0.10.15-1)
[2009-05-30 23:31] upgraded libavc1394 (0.5.3-2 -> 0.5.3-3)
[2009-05-30 23:31] upgraded libiec61883 (1.1.0-1 -> 1.2.0-1)
[2009-05-30 23:31] installed libcaca (0.99.beta16-1)
[2009-05-30 23:31] upgraded gstreamer0.10-good-plugins (0.10.14-1 -> 0.10.15-1)
[2009-05-30 23:31] upgraded gstreamer0.10-ugly-plugins (0.10.11-1 -> 0.10.11-2)
[2009-05-30 23:31] upgraded gtkhtml (3.26.1.1-1 -> 3.26.2-1)
[2009-05-30 23:31] upgraded gucharmap (2.26.1-1 -> 2.26.2-1)
[2009-05-30 23:31] upgraded libarchive (2.6.2-1 -> 2.7.0-1)
[2009-05-30 23:31] NOTE
[2009-05-30 23:31] ----
[2009-05-30 23:31] Add your user to group 'camera' to use camera devices.
[2009-05-30 23:31] upgraded libgphoto2 (2.4.4-1 -> 2.4.6-1)
[2009-05-30 23:31] upgraded gvfs (1.2.2-1 -> 1.2.3-1)
[2009-05-30 23:31] upgraded gzip (1.3.12-4 -> 1.3.12-6)
[2009-05-30 23:31] upgraded jfsutils (1.1.13-1 -> 1.1.14-1)
[2009-05-30 23:31] upgraded libsndfile (1.0.19-1 -> 1.0.20-1)
[2009-05-30 23:31] upgraded sox (14.2.0-2 -> 14.2.0-3)
[2009-05-30 23:31] installed ilmbase (1.0.1-1)
[2009-05-30 23:31] installed openexr (1.6.1-1)
[2009-05-30 23:31] upgraded libpng (1.2.35-1 -> 1.2.36-1)
[2009-05-30 23:31] upgraded qt (4.5.0-5 -> 4.5.1-3)
[2009-05-30 23:31] installed xine-lib (1.1.16.3-3)
[2009-05-30 23:31] installed phonon (4.3.1-2)
[2009-05-30 23:31] installed clucene (0.9.21b-1)
[2009-05-30 23:31] installed exiv2 (0.18-1)
[2009-05-30 23:31] installed strigi (0.6.4-2)
[2009-05-30 23:31] installed soprano (2.2.3-1)
[2009-05-30 23:31] installed xdg-utils (1.0.2-1)
[2009-05-30 23:31] installed kdelibs (4.2.3-1)
[2009-05-30 23:31] installed kdebase-runtime (4.2.3-1)
[2009-05-30 23:31] installed fftw (3.2.1-1)
[2009-05-30 23:31] installed libofa (0.9.3-2)
[2009-05-30 23:31] installed tunepimp (0.5.3-6)
[2009-05-30 23:31] installed kdemultimedia (4.2.3-1)
[2009-05-30 23:31] installed polkit-qt (0.9.2-1)
[2009-05-30 23:31] upgraded k3b (1.0.5-2 -> 1.66.0alpha2-1)
[2009-05-30 23:32] upgraded qt3 (3.3.8-10 -> 3.3.8-11)
[2009-05-30 23:32] upgraded kdelibs3 (3.5.10-2 -> 3.5.10-3)
[2009-05-30 23:32] >>> Updating module dependencies. Please wait ...
[2009-05-30 23:32] >>> MKINITCPIO SETUP
[2009-05-30 23:32] >>> ----------------
[2009-05-30 23:32] >>> If you use LVM2, Encrypted root or software RAID,
[2009-05-30 23:32] >>> Ensure you enable support in /etc/mkinitcpio.conf .
[2009-05-30 23:32] >>> More information about mkinitcpio setup can be found here:
[2009-05-30 23:32] >>> http://wiki.archlinux.org/index.php/Mkinitcpio
[2009-05-30 23:32]
[2009-05-30 23:32] >>> Generating initial ramdisk, using mkinitcpio. Please wait...
[2009-05-30 23:32] ==> Building image "default"
[2009-05-30 23:32] ==> Running command: /sbin/mkinitcpio -k 2.6.29-ARCH -c /etc/mkinitcpio.conf -g /boot/kernel26.img
[2009-05-30 23:32] :: Begin dry run
[2009-05-30 23:32] :: Parsing hook [base]
[2009-05-30 23:32] :: Parsing hook [udev]
[2009-05-30 23:32] :: Parsing hook [autodetect]
[2009-05-30 23:32] :: Parsing hook [sata]
[2009-05-30 23:32] :: Parsing hook [keymap]
[2009-05-30 23:32] :: Parsing hook [filesystems]
[2009-05-30 23:32] :: Generating module dependencies
[2009-05-30 23:32] :: Generating image '/boot/kernel26.img'...SUCCESS
[2009-05-30 23:32] ==> SUCCESS
[2009-05-30 23:32] ==> Building image "fallback"
[2009-05-30 23:32] ==> Running command: /sbin/mkinitcpio -k 2.6.29-ARCH -c /etc/mkinitcpio.conf -g /boot/kernel26-fallback.img -S autodetect
[2009-05-30 23:32] :: Begin dry run
[2009-05-30 23:32] :: Parsing hook [base]
[2009-05-30 23:32] :: Parsing hook [udev]
[2009-05-30 23:32] :: Parsing hook [sata]
[2009-05-30 23:32] :: Parsing hook [keymap]
[2009-05-30 23:32] :: Parsing hook [filesystems]
[2009-05-30 23:33] :: Generating module dependencies
[2009-05-30 23:33] :: Generating image '/boot/kernel26-fallback.img'...SUCCESS
[2009-05-30 23:33] ==> SUCCESS
[2009-05-30 23:33] upgraded kernel26 (2.6.29.2-1 -> 2.6.29.4-1)
[2009-05-30 23:33] upgraded klibc (1.5.15-1 -> 1.5.15-2)
[2009-05-30 23:33] upgraded klibc-extras (2.5-2 -> 2.5-3)
[2009-05-30 23:33] upgraded klibc-kbd (1.15.20080312-8 -> 1.15.20080312-9)
[2009-05-30 23:33] upgraded klibc-module-init-tools (3.5-1 -> 3.5-2)
[2009-05-30 23:33] upgraded klibc-udev (141-1 -> 141-2)
[2009-05-30 23:33] upgraded libdownload (1.3-1 -> 1.3-3)
[2009-05-30 23:33] upgraded libgsf (1.14.12-1 -> 1.14.13-1)
[2009-05-30 23:33] upgraded libsasl (2.1.22-7 -> 2.1.22-8)
[2009-05-30 23:33] upgraded lsof (4.81-1 -> 4.82-1)
[2009-05-30 23:33] upgraded lzo2 (2.02-3 -> 2.03-1)
[2009-05-30 23:33] upgraded man-pages (3.20-2 -> 3.21-1)
[2009-05-30 23:33] upgraded metacity (2.26.0-1 -> 2.26.0-2)
[2009-05-30 23:33] upgraded mlocate (0.21.1-1 -> 0.22-1)
[2009-05-30 23:33] upgraded mplayer (28347-4 -> 29318-1)
[2009-05-30 23:33] upgraded mtools (4.0.10-1 -> 4.0.10-2)
[2009-05-30 23:33] upgraded nautilus (2.26.2-1 -> 2.26.3-1)
[2009-05-30 23:33] upgraded net-tools (1.60-13 -> 1.60-14)
[2009-05-30 23:33] * relogin or source /etc/profile.d/openoffice.sh
[2009-05-30 23:33] * see http://wiki.archlinux.org/index.php/Openoffice
[2009-05-30 23:33] how to use extensions, e.g. for spell checking
[2009-05-30 23:33] see /opt/openoffice/share/extension/install what
[2009-05-30 23:33] is shipped with this package
[2009-05-30 23:33] upgraded openoffice-base (3.0.1-1 -> 3.1.0-1)
[2009-05-30 23:33] upgraded openoffice-es (3.0.1-1 -> 3.1.0-1)
[2009-05-30 23:33] warning: /etc/pacman.d/mirrorlist installed as /etc/pacman.d/mirrorlist.pacnew
[2009-05-30 23:33] upgraded pacman-mirrorlist (20090405-1 -> 20090509-1)
[2009-05-30 23:33] upgraded pango (1.24.1-1 -> 1.24.2-1)
[2009-05-30 23:33] upgraded pidgin (2.5.5-2 -> 2.5.6-1)
[2009-05-30 23:33] upgraded tcp_wrappers (7.6-8 -> 7.6-9)
[2009-05-30 23:33] upgraded portmap (6.0-2 -> 6.0-3)
[2009-05-30 23:33] upgraded ppp (2.4.4-7 -> 2.4.4-8)
[2009-05-30 23:33] upgraded procps (3.2.7-5 -> 3.2.8-1)
[2009-05-30 23:33] upgraded psmisc (22.6-2 -> 22.7-1)
[2009-05-30 23:33] upgraded pycairo (1.8.2-1 -> 1.8.4-1)
[2009-05-30 23:33] upgraded pygobject (2.16.1-1 -> 2.18.0-1)
[2009-05-30 23:33] upgraded python-gdata (1.3.0-1 -> 1.3.1-1)
[2009-05-30 23:33] upgraded python-nose (0.10.4-3 -> 0.11.0-1)
[2009-05-30 23:33] upgraded python-numpy (1.3.0-1 -> 1.3.0-2)
[2009-05-30 23:33] upgraded rsync (3.0.5-1 -> 3.0.6-1)
[2009-05-30 23:34] upgraded seahorse (2.26.1-1 -> 2.26.2-1)
[2009-05-30 23:34] upgraded seahorse-plugins (2.26.1-1 -> 2.26.2-1)
[2009-05-30 23:34] upgraded sysfsutils (2.1.0-4 -> 2.1.0-5)
[2009-05-30 23:34] upgraded syslinux (3.75-4 -> 3.80-1)
[2009-05-30 23:34] upgraded sysvinit (2.86-4 -> 2.86-5)
[2009-05-30 23:34] upgraded tomboy (0.14.1-1 -> 0.14.2-1)
[2009-05-30 23:34] upgraded transmission-gtk (1.42-1 -> 1.60-1)
[2009-05-30 23:34] upgraded unrar (3.9.1-1 -> 3.9.3-1)
[2009-05-30 23:34] upgraded usbutils (0.81-1 -> 0.82-1)
[2009-05-30 23:35] upgraded vlc (0.9.9a-1 -> 0.9.9a-4)
[2009-05-30 23:35] upgraded wireless_tools (29-2 -> 29-3)
[2009-05-30 23:35] upgraded xfsprogs (3.0.0-1 -> 3.0.1-1)
[2009-05-30 23:35] upgraded xkeyboard-config (1.5-1 -> 1.6-1)
[2009-05-30 23:35] upgraded xorg-server-utils (7.4-5 -> 7.4-6)
[2009-05-30 23:35] upgraded xorg-server (1.6.1-1 -> 1.6.1.901-1) -
Filesystem check failed, root partition not found
Hi all,
Since yesterday I receive the following error message when booting into Arch:
:: Mounting root filesystem read-only [ OK ]
:: Checking filesystems [BUSY]
/dev/sda4: no such file or directory
*************** FILESYSTEM CHECK FAILED *******************
* Please repair manually and reboot ...
The device /dev/sda4 is my root partition, which is - after entering the root
password - mounted as /dev/root. Checking the partition with 'reiserfsck
/dev/sda4' does not give any error or warning messages. I can also
successfully remount and access it with 'mount -n -o remount,rw /'.
'ls -l /dev/sda*' gives me the following:
brw-rw---- 1 root disk 8, 0 Apr 28 16:32 /dev/sda
brw-rw---- 1 root disk 8, 1 Apr 28 16:32 /dev/sda1
brw-rw---- 1 root disk 8, 2 Apr 28 16:32 /dev/sda2
brw-rw---- 1 root disk 8, 3 Apr 28 16:32 /dev/sda3
brw-rw---- 1 root disk 8, 4 Apr 28 16:32 /dev/sda4
So the device itself seems to be there. Rebooting doesn't help, neither does
using older, working kernel versions.
I also checked other topics on similar subjects, but I couldn't find any solution.Hmm, it doesn't work even with the UUID. But the error looks similar:
Failed to open the device UUID=672f076e-131c-4220-81ba-b30639ef9285: No such file or directory
But when I call rc.sysinit manually directly after entering the root password,
everything works fine. It does work with sda as well as uuid notation.
I manually added some code before the output of the '*** FILESYSTEM CHECK FAILED ***' message:
ls -l /dev/sda*
sleep 1
ls -l /dev/sda*
The result was:
ls: cannot access /dev/sda*: No such file or directory
brw-rw---- 1 root disk 8, 0 Apr 30 09:12 /dev/sda
brw-rw---- 1 root disk 8, 1 Apr 30 09:12 /dev/sda1
brw-rw---- 1 root disk 8, 2 Apr 30 09:12 /dev/sda2
brw-rw---- 1 root disk 8, 3 Apr 30 09:12 /dev/sda3
brw-rw---- 1 root disk 8, 4 Apr 30 09:12 /dev/sda4
So it seems that the devices are really not yet created. Is it a udev problem?
I am not aware of changing anything udev specific, maybe an updated version? -
[SOLVED] Filesystem check failed - All seems normal
Yesterday i turned of my computer after it had been on for a week or so and this morning i can't get it to boot.
While booting, on the filesystem check stage, it reports all filesystems as clean, but then says [FAIL], and gives me access to the maintenance shell.
- I booted the system with a Gparted live cd and did a check on all partitions on all disks. It reported no errors.
- in fstab I commented out the external disk and the internal one which doesn't contain any system partitions, still the same.
- I remounted root rw in the maintainance shell, and did a full system upgrade (last kernel upgrade was applied) ... still no cookies...
- I also tried to mount all the partitions in the maintenance shell. All were mounted without an error, and as far as i can tell all data was there and browsable at least.
- I tried to boot with a /forcefsck file and the checks were all done without any messages, after which it failed as usual.
Also i tried fallback (before the upgrade), which as you can guess by now, also gave the same error. The message about the filesystem check failing is not giving me any useful information. All it does is list the partitions saying every partition is clean, and then says the filesystem check has failed.
As you can probably tell, I did all the steps I could find on the forums that looked it could solve my problems, and I've hit a dead end. If I knew which partition had the problem I could move the data and format it. Could this be a hardware error?
Thanks in advance for any help offered
Last edited by vexxor (2009-07-28 11:04:02)KimTjik wrote:Maybe a stupid question, but it's not that some partition is totally full?
Nope. I just checked.
Funny thing. In the maintenance console, when i do a "mount -a", I can navigate to the now mounted directories, but I can't see the mounted partitions as an output of either "mount" or "df".
I figured this out when I was checking if the disks were full. Root gets shown, and its on 53%. Just in case i deleted about 20GB of stuff from the media partition, but the problem remains. -
First boot - filesystem check failed.
I just installed Arch on a clean drive. Newly partitioned with /, /home, and swap partitions. After installation and a reboot, GRUB loads. Then after a while loading the OS, it says filesystem check failed.
/dev/hda1:
The superblock could not be read or does not describe a correct ext2 filesystem. If the device is valid
and it really contains an ext2 filesystem (and not swap or ufs or comething else), then the suberblock
is corrupt, and you might try running e2fsck with an alternate superblock:
e2fsck -b 8193 <device>
Running that command gives:
No such file or directory while trying to open /dev/hda1
My machine is an IBM ThinkPad, model R40. The copyright year on the bottom is 2003. The hard drive is a 20 gigabyte Fujitsu. I don't know what else people need, but I always get asked for more info right away when enquiring about these things. So, the logo is on the bottom-right and the letters are red, green, and blue. The Intel Centrino sticker on the other side is starting to peel off. What else do you need to know?Mounting Root Read-only [DONE]
Checking Filesystems [BUSY]
/dev/hda1:
The superblock could not be read or does not describe a correct ext2 filesystem. If the device is valid
and it really contains an ext2 filesystem (and not swap or ufs or comething else), then the suberblock
is corrupt, and you might try running e2fsck with an alternate superblock:
e2fsck -b 8193 <device>
***************** FILESYSTEM CHECK FAILED *****************
* Please repair manually and reboot. Note that the root *
* file system is currently mounted read-only. To remount *
* it read-write type: mount -n -o remount,rw / *
* When you exit the maintenance shell the system will *
* reboot automatically. *
That looks better in monospace, but that's an exact copy. Else it'd have better grammar. In /dev, I can see:
sda
sda1
sda3
Yet no sda2. Nor any hda's. Hmm! What's all this, then?
[Edit] Ugh, submitting that thing makes it look even worse. You can read it, though. [End edit]
Last edited by Qoph (2009-12-28 22:03:30)
Maybe you are looking for
-
HT4972 my ipad switched to German! How do I get it back to English?
My iPad switched to German while I was synching it to my computer. How do i get it back to English?
-
Table Types in Function Module
Hi, How to use a table to capture the data from a file, in function module instead of using TABLES parameter. This parameter should exist in IMPORT parameters of Function Module Many Thanks in Advance
-
Is there a Ffx Sync like app that works through my own LAN? No cloud please.
I'd like to keep 2 or more profiles synced without going on-line. I don't wish to use "the Cloud". I don't care how secure you claim my data will be in your possession. I read about DB's hacked into daily, even without passwords! Besides the direct c
-
Hi, I am working on program to create quotation using bapi function module BAPI_QUOTATION_CREATEFROMDATA. I am getting following error: Requirements are not fulfilled for condition EDI1 I have filled up this three structure with following flelds head
-
Ho w to make a class immutable?? Thanx in advance