Help with install WRT54G

i just purchased a WRT54G v6 router peice after getting my new laptop... but i have ran into some issues getting it to work with internet ... to be more specific, i can connect to it (the router) no problem ... but i can not view any webpages... (it has firmware v 1.01.1 if that matters)
my ISP is bellsouth DSL service
with a westell modem c90 610030 06
this modem has the advanced config options locked out so i can not check it to see if it is running as a DHCP server .. but i beleive it is (from viewing the source code for the advanced html page) ...
i can connect to the internet fine when the modem is hooked directly to my computer, and i can connect to the internet fine when my modem is hooked into my other linksys router (BEFSR41)
i tried to configure the new wireless router to the 'router' setting instead of gateway .. but had no luck and had to reset it completly to be able to even connect to the config page again ...

an update, i have it kinda working .. but would still like to resolve the issue on why i can not use the new router by it's self
how i have it working right now ... i disabled DHCP on the new peice, and assigned it a different IP addy that was out of normal range (192.168.1.200) and just plugged a cable between the two routers ...
and disabled DHCP on the old peice ... now all of the computers work on the internet ...
my laptop, wirelessly ... and my two wired computers ...

Similar Messages

Need help with a WRT54GS V5.1

i need help with my WRT54GS V5.1 wireless router. it cannot connect to the internet and i don't know why. at the moment i have to use an ethernet cable coming from a virgin media modem. information that might be usefull. one of the antennas on the router is broke i am using windows vista on a toshiba laptop. the model is WRT54GS V5.1 thanks for people who help note: i am only 13 so somethings you say i might not understand.

Access Setup page of router .....
Click wireeless tab .... have a note of the wireless settings on that page .... Please click on the tab "Application and gaming" and click on sub
tab "Port range forwarding"
1) On the first line in Application box type in "Xbox", in start box
type in 88, in end box type in 88, in protocol keep it both, in ip
address type in 192.168.1.20 and give a check mark on enable box.
2)   On the second line in Application box type in "Xbox", in start box
type in 3074, in end box type in 3074, in protocol keep it both, in ip
address type in 192.168.1.20 and give a check mark on enable box.
3) Now save the settings
4) Once you return to the setup page, click on the tab "Administration"
and disable the UPNP and save the settings.
5) Now assign the given ip address on your xbox
   ip address :- 192.168.1.20
   subnet mask :- 255.255.255.0
   default gateway :- 192.168.1.1
Please assign the dns address on the xbox
primary dns :- 4.2.2.2
secondary dns :- 192.168.1.1
6) Please try to test your xbox live.

Installing Elements 11 on Mac. Need help with install error "Setup wants to make changes."

Installing Elements 11 on Mac 10.8.2. Need help with install error: Setup wants to make changes. Type your password to allow this." After entering Adobe password, nothing happens. Locked from further installation. Any ideas? Adobe phone support could not help.

Just before letting changes (installation in this case) be made on the system, Mac OS prompts for password & this has to be the Mac system password. This password prompt is the system's own native prompt & would accept the system password only. Please make sure it is the right system password (all/admin rights) and the installaion should run.

Help with installing 10.6.3

Hello, I'm looking for a bit of help with installing Mac OS X 10.6.3 without screwing up.
I currently have a Macbook with 10.6.3 on it, and I want to COMPLETELY reset my Mac. I want to have a pretty much brand new Mac with 10.6.3, which I have the disk for. I actually just updated from 10.5.8, hoping that it would erase my hard drive and re-install, but it didn't. So I would like help with how to completely reset my Mac, and re-install 10.6.3.
Thanks in advance!
~Dan

Use that disk, but after booting from it and before running the install, choose Disk Utility from the Utilities menu and erase the drive.
(75462)

Hello I need your help with installing the flash drive into my laptop

Hi
I am Rachel Friedman asking for your help with installing the flashdrive player into my laptop.
Thanks
Rachel

To give you any useful advice, I'm going to need to know more about your computer and browser:
https://forums.adobe.com/message/5249945#5249945

MOVED: help with installing 2 os on one hd

This topic has been moved to Operating Systems.
help with installing 2 os on one hd

RedMoose:
Congratulations on installing an upgraded HDD into your PowerBook.
I am not sure exactly what happened in the formatting process, but here are some directions that should help:
Formatting, Partitioning Zeroing a Hard Disk Drive
Warning! This procedure will destroy all data on your Hard Disk Drive. Be sure you have an up-to-date, tested backup of at least your Users folder and any third party applications you do not want to re-install before attempting this procedure.
Boot from the install CD holding down the "C" key.
Select language
Go to the Utilities menu (Tiger) Installer menu (Panther & earlier) and launch Disk Utility.
Select your HDD (manufacturer ID) in left side bar.
Select Partition tab in main panel. (You are about to create a single partition volume.)
Select number of partition in pull-down menu above Volume diagram.
(Note: 1 partition is normally better for an internal HDD. External HDDs usually have more than one. See Dr. Smoke’s FAQ Backup and Recovery for tips on partitioning external HDD.)
Type in name in Name field (usually Macintosh HD)
Select Volume Format as Mac OS Extended (Journaled)
Click Partition button at bottom of panel.
Select Erase tab
Optional: (Select the sub-volume under Manufacturer ID (usually Macintosh HD).
Check to be sure your Volume Name and Volume Format are correct.
Select on Security Options button (Tiger) Options button (Panther & earlier).
Select Zero all data. (This process will map out bad blocks on your HDD. However, it could take several hours. If you want a quicker method, don't go to Security Options and just click the Erase button.)
Click OK.
Click Erase button
Quit Disk Utility.
Open installer and begin installation process.
Please post back with further questions, comments or an update.
Good luck.
corneius

Help with Installing flash error- metafile cannot be loaded

I read the forum on this but it ended last year and there was no response to some recent questions on this and the direct email to the Adobe rep. on there got no response.
I am having this problem with installing Flash- it gets about 30% of the way and then a message comes up that says the metafile cannot be loaded.
I am running 10.7.5 on Mac, all browser software is current. I use both Safari and Chrome. After it said Flash was out of date I tried to update but got the metafile error. So I uninstalled Flash to install it fresh but the same error came up. I tried everything recommended from the forum. I also did all the steps from the help list direct from Adobe ( deleting Flash files, folders, rebooting, etc.) The offline link Adobe provides says the "file cannot be found" so I can't download that either. So I tried the online link download, but even after doing all the steps in order etc. I still get the error when I try to install it.
I have no firewall and have no virus software running. I also tried the direct offline links that others have provided from 2013, (unfortunately they are old) in both clicking on them and also downloading by right click but they are dead links and even the download for it has no content.
Any help that is more recent than last year? If this is in the wrong place, apologies. New to the forum.

I tried all solutions but one posted in adobe support. I am local administrator but IE security settings are set by group policies and buttons in tools security setting are grayed out.
After three days with "The ActiveX control for Flash Player could not be registered" message I tried registering the activeX control manually.
Bingo! that made the trick.
So open a DOS window, type "regsvr32.exe C:\WINDOWS\system32\Macromed\Flash\Flash10d.ocx" -first check if this directory exists and contains the Flash10d.ocx (no quotes needed) and you should receive a confirmation that it registered correctly.
I must say that I've tried so many ways that I cannot repeat the correct order before this has worked ;-(
Hope it works for you all

Help with installing pre-requisite packages on Red Hat Linux

Having issue with installing packages with yum
OS is RHEL 6 and following package which are prerequisites for Oracle Fusion Middleware install on Red Hat Linux 6
uname details as follows
2.6.32-220.el6.x86_64 #1 SMP Wed Nov 9 08:03:13 EST 2011 x86_64 x86_64 x86_64 GNU/Linux
Example error: yum install gives error as follows for all packages.
No package compat-libcap1-1.10-1 available
Need to install following packages (as mentioned in the prerequisites)
binutils-2.20.51.0.2-5.28.el6
compat-libcap1-1.10-1
compat-libstdc++-33-3.2.3-69.el6 for x86_64
compat-libstdc++-33-3.2.3-69.el6 for i686
gcc-4.4.4-13.el6
gcc-c++-4.4.4-13.el6
glibc-2.12-1.7.el6 for x86_64
glibc-2.12-1.7.el6 for i686
glibc-devel-2.12-1.7.el6 for i686
libaio-0.3.107-10.el6
libaio-devel-0.3.107-10.el6
libgcc-4.4.4-13.el6
libstdc++-4.4.4-13.el6 for x86_64
libstdc++-4.4.4-13.el6 for i686
libstdc++-devel-4.4.4-13.el6
libXext for i686
libXtst for i686
FYI: If this forum is not appropriate please let me know appropriate forum and shall repost there.

Hey,
Normally I use YUM : http://taliphakanozturken.wordpress.com/2012/03/17/how-to-use-yum-to-install-rpm-packages-with-dependencies/
Let me know if this is what are you looking for.
I hope it helps you,
Thiago Leoncio.

Help with installing CS2 in Snow Leopard

Can anyone help me with installing CS2 on a MacBook running OSX Snow Leopard? I have trouble with activating the product and get a splach screen with a monkey element or logo rather than the adobe logos... confusion reigns!

Hi Rory, be aware that running CS2 products on Snow Leopard isn't going to be a supported combination. Here's a related thread: http://forums.adobe.com/thread/499253. Apparently some customers have been able to run CS2 software on Snow Leopard. You can also check with our chat support at http://adobe.ly/v6wfLL. However, I can't be certain that they'll be able to assist you. You might want to consider upgrading.

Need help with installing old version of firmware

I would like to revert to an old version of firmware for my Airport Extreme base station. I have read in a number of postings that this would possibly help with the problem of my Canon Pixma ip3000 not working after the firmware was usdated. When I tried to install the old firmware, the Installer would not allow it, there was just a message that the software was up to date. Could anyone please give a step by step description of how this can be done? Is there a way around the Installer? Thanks.

The firmware supplied with the base station was 4.1. After installing it, everything worked just fine, including wireless printing to a Canon Pixma ip3000. At one point, after being prompted by a message onscreen to upgrade to 4.2, I did the download and installation, and that is when all the problems started. No wireless printing, and I can't seem to use the Airport Admin or Assistant (not responding). Since then I have also upgraded the OS to 10.4.5.
I am trying to downgrade to 4.1 since that is what worked initially and what was suggested in another posting I read.
I did look at the information for the various parts of Airport and noticed that the Setup Asistant is 4.2, the Admin Utility is 4.2 and the base station is 5.5.1. Could this be affecting the problem as well?
I will try downgrading using the link you provided. Thanks very much.

Need help with installing on Photosmart C7280 all-in-one

I did have my printer installed, and was using the printer for 3 laptops wireless within my home. Now I can not even find my Backup disk, so i need help with downloading the software to use my printer, and also get it back to being used wireless. I do not know what happened, but the fax for this printer is listed, just not the printer itself. please help!
This question was solved.
View Solution.

Click here to download the software for your printer:
http://h10025.www1.hp.com/ewfrf/wc/softwareCategory?product=3204785&lc=en&cc=us&dlc=en&lang=en&cc=us
chose the appropriate operating system that corresponds to your computer and download the full feature software.
Please click on KUDOS if you find my solution helpful.

Help with installing CS3 on new Mac

Recently purchased new Macs for the department. Cannot install CS3! It asks for the CS2 license number which we have. Turns out it doesn't recognize it. Called customer support and everyone had the same answer, but no solution. I purchased the CS2 corporate license when we had about 6 Macs. Now, we're down to 3 so I purchased the CS3 as individual suites. They said there is no workaround with getting CS3 to recognize the CS2 license! We called 4 different times and talked to 4 different reps who gave us all the same broken-record response. Any help with be greatly appreciated!

I believe that is essential what the customer service folks were telling my designer. However, both was installed before on the old Macs (CS2 corporate licensed and CS3 individual license) - that's the odd thing, is that it worked before on an older system. All we did was buy new hardware.
I hope this isn't Adobe's way of making us upgrade to CS4 - lol!

Help with installing SAP

Hi Everyone,
We are currently undergoing a restructure of SAP and I have been tasked with the installation of SAP in our environment.
The systems I have been tasked with installing is the following
ECC (Enterprise Core Component)
BW (Business Warehouse)
SRM (Supplier Relationship Management)
EP (Enterprise Portal)
PI (Process Integration
I have been wandering around on the SAP website and found a load of documents referring to the install however I don't seem to be able to find the correct software or guides to help me with installation of these system.
Please could someone help me by giving me the links to the documents that I would require. Also I would like to know how do I actually install each system? Can I download all the applications on this site? Any other information you could give me would be great.
Regards,

Hi,
you'll find all the guides via service.sap.com/instguides or via the new site support.sap.com via documentation.
lots of work to install ECC, BW, SRM, EP and PI for Development(, Test) and Production.
kind regards,
Martin

Need Help with install of Final Cut Pro HD

Hi
I am tryting to install FCP Express HD on my G4 Ibook and I get a strange error message. It was able to instaLL fine but when I got to run the program I get this message
Can't install unable to find easy setup file please reinstall and try again.
I have uninstalled and resinstalled 2x any ideas
Ibook g4 Mac OS X (10.4.3)

Make sure you uninstall all the components of Final Cut. Do a search on your Finder. Then install from the installation disc. If this doesn't work you should contact Apple for help with installation issues. The disc may be defective.

Help with the WRT54g

Hi, I have been having trouble with my internet connection ever since I purchased a PC running Windows Vista Home Premium (32 bit). I have a total of 3 PCs an Xbox 360 (all wired) and a Wii on the wireless. I have never had any problem with the internet connection until I connect the PC running Vista. If I unplug the computer running Vista the other connections run great. The interenet will run for a long time in some instances but will at other times disconnect every few minutes. I have tried searching google for solutions, called HP support and Linksys support and no one has been able to help. The Wrt54g v.8 is brand new, just bought it about 3 weeks ago after the last one died. I have made sure that all firmware is up to date. If anyone has any advice that could fix this annoying problem I would appreciate it. Thanks a lot.

Gollum wrote:
Try this setting;
Wireless channel -1 or 11
Beacon Interval – 50
RTS & fragmentation threshold – 2306
Let me know if it works.
Thanks, I changed the settings, and I already had the MTU set at 1400. We will see if that helps. Thanks again for the replies

Help with install WRT54G

Similar Messages

Maybe you are looking for