Help with messed up Audio

I am putting together a video for my girlfriend, it is a collection of clips, I have music overlayed so all the audio in every clip is taken down to 0%.
the problem is... when i play it in imovie it is fine
when i export it to put into idvd or play in itunes, i get to a part in the movie and a portion of audio from ONE clip only plays
it plays at normal speed even though the clip is sped up
it plays in a section NOT THE CLIP IT IS FROM
i have removed that clip, reinserted and re-exported
it still happened exactly the same
I do not want to make the whole thing over as it took weeks to create this movie. What can i do to fix this problem!!?

I've seen audio problems when a sped changed clip is set to a speed other than one of the default "ticks". What is the speed of that clip?

Similar Messages

  • Help with front panel audio on K9N board.

    Okay, I admit I'm a bit of a moron with front panel audio but I just can't figure out how to configure this board with my case.  Here are the pins:
    Case:
    Mic In
    Mic Bias
    SpeakOut L
    Return L
    SpeakOut R
    Return R
    Ground
    Motherboard:
    PIN    SIGNAL                  DESCRIPTION    
    1    PORT 1L                  Analog Port 1 -Left channel    
    2    GND                  Ground    
    3    PORT 1R                  Analog Port 1 -Right channel    
    4    PRESENCE#     Active low signal -signals BIOS that a High Definition Audio dongle is connected to the analog header. PRESENCE# = 0 when a High Definition Audio dongle is connected.    
    5    PORT 2R                  Analog Port 2 -Right channel    
    6    SENSE1_RETIRN     Jack detection return from frontpanel JACK1    
    7    SENSE_SEND     Jack detectionsenselinefrom the High Definition Audio CODEC jack detection resistor network    
    8    KEY                  ConnectorKey    
    9    PORT 2L                  Analog Port 2 -Left channel    
    10    SENSE2_RETIRN     Jack detection return from frontpanel JACK2    
    I haven't been able to make any sense of the two, so if anyone here can help, I would appreciate it very much.

    Quote from: crazy on 09-June-06, 15:51:46
    You may tell us more information about your mainboard, please give us the detailed name of your mainboard. :D  Then there will be more users could give some suggestions.
    Sorry, there aren't that many K9N boards out there, but mine is the K9N Platinum MS7250 Version 1.0.  It's the AM2 non-SLI nVidia nForce 570 Chipset model.
    Thanks for any help.

  • Can anyone help with Bluetooth and Audio output conflict?

    Audio ouput from media files on Quicktime, Real Player and Windows Media will only play through my Bluetooth headset .
    I have tried resetting the Audio output preferences to no effect. Also tried reinstalling Bluetooth devices.
    When opening file the player returns the following message:
    "There was an error connecting to your headset. Make sure it is turned on and in range. The audio portion of the program you were using may have to be restarted."
    Please Help!
    Mac Book Pro 17" Mac OS X (10.4.7)
    Sorry for repeat but new to this.

    Hey DS.. Im having the same exact issue as you and Im sure alot of other people are as well... it seems to be touch and go. I currently own a Mac Mini Solo with an intel 1.5 ghz processor and I have a Motorolo H700 Bluetooth headset. I can get mine to work for a short while watching movies or what not or use it in iChat but then after so many minutes my computer has a spastic fit with the thing and i get the exact error message you described. However when I attempt to go back into my Audio Control Panel to switch audio from the BT headset back to the line out.. the control panel seems to freeze up as well causing me to reboot my entire system just enough to switch the audio back to the line out. I think that this is an issue on apples end that they need to update their blue tooth software or something as you really cannot update software to a BT headset only the device it communicates with. So I think in the meantime we are all screwed until apples gets off their butts and does something about this.

  • Help with "Error syncing Audio and Midi" message. How to fix?

    Hi,
    I'm running Logic Pro 7.1 on a G5 Dual 2.5 PowerMac. My audio interface is a Digidisign Digi002R, and my MIDI interface is a MOTU Fastlane. Up until a few days ago everything was working fine. I didn't install any new software or anything.
    All of a sudden in any Logic session I open (new or saved) I get all kinds of artifacts that sound like they're associated with sample rate problems.
    True to form, on playback after 4 or 5 seconds a message comes up telling me that there is an error syncing audio and midi. It tells me that a sample rate of 88209, or 88213, or 88207 (each time it's different) was detected, and that there is a conflict between Logic and my external device.
    My Digi002R is set to 44.1, and Logic is set to 44.1 as well. I have no idea where this problem came from.
    The only thing I do know is that I've been using the Peachtree Press Apple Pro Training Series to study for my Level 1 Logic certification. it comes with a CD with Logic sessions to use with the text. The CD comes with a Logic Epress Demo but I didn't download that as I've already got Logic Pro. I dragged those session files to my desktop, and the problem occured for the first time when iopened up that first session from the CD. After that, every single session has this problem and I have no idea how to fix it.
    Sorry for the incredibly long message, but can anybody help?
    Thanks
    PowerBook G4 15", PowerMac G5 Dual 2.5   Mac OS X (10.4.7)  

    Hey,
    Thanks. I appreciate the help, but I've tried all of that. I just don't get it. I've unplugged everything, I've shut down, powered down, relaunched everything a dozen times and the problem doesn't go away. I know that the problem is with Logic because the interface works perfectly fnie with everything else, from Pro Tools to iTunes.
    I'm having Logic Pro 7.2 shipped to me so I'm hoping that installing that will reset everything, but until then I can't do anything in Logic.
    Anybody ever encounter anything like this?

  • Can anyone help with a CS5 Audio Sync problem?

    making a simple game with video stills matching a running audio track
    my audio is an MP3 i built in GarageBand
    all works well in flash, but when rendered to QT, the audio and video go out of sync, and some video drops out too
    have put all audios on their own layer and streamed them all too, set settings in Publish to 64, but still have same problem
    any help?

    Sorry, can't help.  But misery loves company.  I have the same problem with Premiere.

  • I need help with my iTunes audio configuration, its been giving me error messages for 3 weeks now!!!!

    I have been receiving this message for 3 weeks now," iTunes has detected a problem with your audio configuration. Audio/Video playback may not operate properly." I've tried uninstalling and even deleting my quicktime player and then installing it again. I've also tried uninstalling and deleting my itunes and then redownloading it again. I have also made sure that both are up to date, but still it gives me that **** error message. I cant listen to any of my songs or any new songs, please help.

    I have been receiving this message for 3 weeks now," iTunes has detected a problem with your audio configuration. Audio/Video playback may not operate properly." I've tried uninstalling and even deleting my quicktime player and then installing it again. I've also tried uninstalling and deleting my itunes and then redownloading it again. I have also made sure that both are up to date, but still it gives me that **** error message. I cant listen to any of my songs or any new songs, please help.

  • Help With a Custom Audio Spectrum I am Making

    So here is the plan, I want to make something like this:
    but in order to do that I need to use sound keys (which I have) and I don't know how to use it very well so please keep it simple when replying.
    So with sound keys, I can make rectangles move to the beat of music like in here (no they do not use the audio spectrum in this vid and duplicate it, so hear me out) they make solid layers of rectangles and make them move up and down to the beat of the music using ranges, I know what the ranges I need to use are in sound keys, but I do not know how to make the scaling work correctly. When I hook up the rectangles scale with the music, it moves both sides, people have said you need to move the pixels rather than the scale, so how do I do that, also when I hook it up it ends up being extremely small (the rectangles) so I need help solving these two problems, so please help me, remember I am a noob and have no idea how to use equations and stuff. Thanks!

    You need to move the anchor point for your rectangles to one side or the other so that, when they scale, they will only appear to move in one direction.
    If you're a "noob", you should really start here: Getting started with After Effects. The resources in that link will get you started in a way that will make you able to come up with this stuff on your own.

  • Help with NAS (Network Audio System) setup.

    Anyone having any ideas how to set up this? I couldn't find any documentation, no howtos, no help, just an obscure nasd.con.eg in the package.
    Has anyone managed to set up a client and a server for this system, it'd be really useful to me...

    Idd, seeking is hard and really hacky (:D) to implement with the two process solution. :\ You can use the
    extern-movie.sh 10.0.0.4 movie.mkv 124
    to seek where you want in the files, but you'd have to exit the script, then restart the script in the middle of a movie ... :\ Writing a plugin for MPlayer might kinda defeat the simplistic design of rsound. Shouldn't be hard to implement though. I made an rsound client in python in like 5 mins, so shouldn't be too hard.
    As for NAS: http://linux.die.net/man/1/nasd this helped a little, but it really looks like legacy software. "When the Network Audio System server starts up, it takes over /dev/audio."
    I've been trying to get nas up and running, and it wasn't hard to get it to play some stuff with mplayer, but it feels quite broken using the default config + mplayer. Might be my alsa emulation of course, but mplayer showed hickups, erratic framerate (-autosync 100 helped against this), bad sound quality, and a couple of crashes.
    You could try this from the command line. Shouldn't need to set-up any config file yet.
    sudo nasd -aa
    And running this in another shell:
    mplayer <movie> -ao nas
    Try it locally, not sure how to set up nas to connect to extern servers. :\
    Last edited by Themaister (2010-01-04 18:47:10)

  • Help with messed up iPhoto Library

    I fear that I have made a horrendous mistake. I purchased a new Macbook Pro and used the Migration tool. I didn't see where the iPhoto Library transferred over. I found my iPhoto Library on the old Macbook and drug it into Dropbox since it would sync with the new computer. When I opened iPhoto on the new computer all of the events were messed up. None of them are named correctly. A lot of them say they have photos in them but the photos show up as a gray triangle with an exclamation point.
    I thought I would check the old computer, but because iPhoto Library is in my Dropbox it simply synced and replicated the "bad" one.
    Is there any way to get the "old" iPhoto Library back?

    What is your iPhoto version that created the iPhoto Library?
    Yes, storing the iPhoto Library in the DropBox probably is the reason, that the library got corrupted. Don't store it on network volumes.
    The best way to restore your iPhoto library would be to restore it from your most current backup.
    Alternatively you could try to rebuild the library. The procedure differs, depending on your iPhoto version, see: iPhoto 6 and later: Rebuilding the iPhoto library
    If that does not help, you could try to rebuild the iPhoto library using iPhoto Library Manager, but that will not be able to restore your book, cards, ..., only the Photos and events.
    How to do that is described here by Terence Devlin,
    see Option 2:  Re: iPhoto thumbnails distorted after every import
    Fat Cat Software – iPhoto Library Manager
    Regards
    Léonie

  • Help with Powering m-audio firewire 410

    Hi to All
    I just got a Mac book Pro, and I own an m-audio firewire 410 interface. The Mac works wonderfully and I´m extremely happy with it and the 410 together.
    Does Anyone know if there is a way to power the interface with the AC adapter, whithout powering it through the 6 pin Firewire port when using batteries ?
    To My understanding, the 6 pin ports always can power devices.
    Thanks for Your Help, and sorry of any English glitch

    I have a MacBook Pro and a M-Audio Firewire 410. As we speak, I am running a six pin firewire cable to the Firewire 410 as well connecting it to the supplied AC power adapter. Nevertheless, I use it primarily with my PowerMac G5. When connected to the G5, I have both the 6 to 6 pin firewire connector and the supplied AC power power adapter connected and sending power to the unit. Nowhere in the manual does it say that you cannot connect the AC power adapter to the FW 410 while a six pin (powered) firewire cable is in use. It does say that the AC adapter is included to power the unit when a computer with four pin firewire ports (the kind that don't supply power) is connected to the FW 410. As bus power from a firewire port is often the victim of RFI from the components in the computer, I was advised by M-Audio tech support to utilize external power whenever feasible to increase the SN ratio on the device. So basically they told me to connect both at the same time. I assume that the FW 410 knows when it is receiving power from the AC adapter and knows to not utilize the power from the firewire bus simultaneously. If you are really worried, I suggest you call M-Audio tech support and let them tell you what I just did. One final thought: I have used my FW 410 with two power sources (firewire and DC in) for the two years since I've had the unit. It doesn't work as well as it used to...now that the drivers have improved, it works much better a than it used to. I hope this answers your question.
    2GHz DP PowerMac G5 (generation uno) / MBP 15" 2.16 GHz   Mac OS X (10.4.6)   4 GB RAM & 6800 Ultra Nvidia Graphics / 2 GB RAM
      Mac OS X (10.4.6)  

  • Need help with the T400 audio driver.

    I recently purchased a refurbished T400 (type 6475-GS6) at a great price.  I've installed XP 64, downloaded then installed all, or what I thought was everything from the Lenovo web site.
    But for the life of me, I can't install the Conexant audio driver because the device driver installation wizard can't find the device for the driver.
    Does anyone have a suggestion?
    Thanks in advance for your time and help.
    Dale

    You might need KB888111.
    W520: i7-2720QM, Q2000M at 1080/688/1376, 21GB RAM, 500GB + 750GB HDD, FHD screen
    X61T: L7500, 3GB RAM, 500GB HDD, XGA screen, Ultrabase
    Y3P: 5Y70, 8GB RAM, 256GB SSD, QHD+ screen

  • Need help with iTunes and audio config

    i get an error message and can't open up the program.
    iTunes cannot open because it has detected a problem with your audio configuration.
    So what do i do??

    Try the instructions in this article.
    (23165)

  • Need help with GUI Scripting Audio Midi Setup

    I want to read the value of the sampling frequency set by default in Audio Midi Setup.
    If there is an easy unix way to gleen this, please let me know. Otherwise, I am trying to get it via GUI scripting. I think I am almost there, but am doing something stupid.
    Here is what I have:
    tell application "Audio MIDI Setup"
    activate
    end tell
    tell application "System Events"
    activate
    tell application process "Audio MIDI Setup"
    select window 1
    select group
    select tab group
    select group
    select combo box
    set FrequencyValue to contents of combo box
    end tell
    end tell
    Basically, this comes down to the question of how to extract the default text field from the combo box.

    Once you click on the combo box to get the list of items, you can do stuff with the results. The easiest thing would probably be to use the up and down arrows to change the selection, since the text field is not editable. You can compare the list of items with the current value and do something from there - how do you plan to choose the item to change to?
    <pre style="
    font-family: Monaco, 'Courier New', Courier, monospace;
    font-size: 10px;
    font-weight: normal;
    margin: 0px;
    padding: 5px;
    border: 1px solid #000000;
    width: 720px;
    color: #000000;
    background-color: #DAFFB6;
    overflow: auto;"
    title="this text can be pasted into the Script Editor">
    tell application "Audio MIDI Setup" to activate
    tell application "System Events" to tell application process "Audio MIDI Setup"
    set comboBox to combo box 1 of group 1 of tab group 1 of group 1 of window "Audio Devices"
    set frequencyValue to value of comboBox -- get current value
    click button 1 of comboBox -- perform action "AXPress" to drop the list
    set theChoices to value of text fields of list 1 of scroll area 1 of comboBox -- get all the values
    -- keystroke (ASCII character 31) -- down arrow
    -- keystroke (ASCII character 30) -- up arrow
    -- keystroke return -- select and dismiss the list
    end tell
    activate me
    choose from list theChoices default items {frequencyValue} -- just show the results
    </pre>

  • Can anyone help with Quicktime Pro audio prob?

    I've been trying to compress an audio/video file shot on my Cybershot so that I can upload on a contest website. Every time I copy into I-Movie, I have no audio (although it plays fine on my desktop). I was told I-Movie does not support muxed streaming. At Apple's recommendation, I upgraded to Quicktime Pro.
    The audio and video both work fine when I play it in Quicktime Pro; but when I export it from Quicktime to either MPEG4 or Quicktime Movie, I get no audio. (Also, the audio setting area is grayed out.) Any suggestions? I need to send the file 320X240 around 15 mb by midnight tonight.
    Thanks for the help...

    Use the "Export to DV" option. (Any of the sub options will work.) Split into segments if needed for older versions of iMovie.

  • Help with 5.1 Audio Out via TosLink Optical Cable

    My Mac mini is connected a Vizio 5.1 sound bar with a TosLink optical cable. In the Sound preference pane, the name of the device for sound output is "Digital Out". However, when I go into Audio Midi Setup, the Built-In Output shows "0 in/2 out", and if I click the Configure Speakers button, I only have the option to choose "Stereo" from the Multichannel pull-down menu (regardless of the Format I choose).
    Why doesn't my Mac mini recognize my sound bar as a surround sound-capable device and send it a 5.1 audio signal?

    I'm not sure I completely understand the solution described in your link, but I followed the instructions and it did not solve my problem. I think one issue is that I'm not given the option in the Format pull-down menu to select anything other than 2-channel audio.

Maybe you are looking for