Help with midi/usb interface and Logic 8

Hi there,
So here is the 'goal'
I have a SoftStep (MIDI USB interface) running into Logic 8 or Mainstage - my ideal scenario would be to pre-load various loops, clicks and Ambient Pads into Logic - these are usually in MP3 format.
Ideally, I would then be able to assign various buttons on the MIDI footpedal to start, stop and cycle through the various files.
Is this possible, and if so, how would I go about setting this up?
Many thanks in advance for your help.
T

he driver is indeed a universal version.
Cool.
I doubt it's the MIDI interface simply because when I used it to connect a Roland Juno-D to the computer, it worked perfectly fine.
Ok, cool. Rules that out
Notes get ''stuck'' on the visual keyboard, some notes are still considered 'pressed' until I press them again. There aren't many but it's worth noting.
Is it always the same notes? For instance, if C3 will never give a note off, it might indicate a problem with the actual keyboard mechanism in the piano.
ANYWAYS, when I've placed a monitor inside the environment at the places you mentioned, I can indeed see those odd low notes.
So it seems like the piano is sending low notes as you play the keyboard...
So I see this is a pretty solid visualize representation of what I thought was wrong. Note the C-2 is lower than I can even reach on my standard sized piano (my lowest note is A-1).
It certainly seems as though the piano is sending spurious MIDI data, as I mentioned, it might be the actual physical keyboard mechanism is mistriggering. From the things you've tried, it certainly sems to be the actual piano that's playing up, and not the MIDI interface or computer.
At this stage, I'd probably try playing around with the piano's MIDI settings, trying a reset procedure if it has one. It might be something as simple as dirt and crud in the keyboard causing mistriggering.
While you could use the environment to filter out those C-2 notes, it's not really going to help if the piano is missing note offs and triggering wrong notes. It might, as you initially suspected, be knackered...

Similar Messages

  • Help with M-Audio interface and GB

    First time with any kind of audio interface and GB. I just got a M-Audio Mobile Pre USB and am a little confused by the monitor settings. Been to the web site and read the manual and they said turn the monitoring off in garageband so I don't hear double monitoring. My question is, is it possible to record and hear the effect I have chosen as well. With monitor off all I can hear is the dry signal.I never had to worry about this before since I was going directly into the Mac, no interface. Is there a FAQ or web site that can help a newb like me with these most basic questions?

    Sounds like good advice Christoph. I have been only recording bass thus far, very few effects and no latency yet. I was puzzled by the M-Audio manual that says to turn off the software monitor but on the M-Audio web site forum an expert says to turn on the monitoring in garageband. This will all makes sense to me soon I hope.

  • I need some help with MIDI and accessing samples

    I recently purchased Logic Express 9. I'm really happy with it--it's certainly a step up from Garageband--but I'm having trouble connecting my MIDI keyboard. In Garageband, I was able to just plug the keyboard in using a MIDI/USB cable and play software instruments immediately. But in Logic, when I connect the keyboard (a Yamaha PSR-273) into a USB port, it doesn't even register! Right now, the only way for me to play software instruments is through the Capslock keyboard, and I would prefer to play on real keys. How can I connect my keyboard so I can play Logic software instruments?
    Also, I read on the Apple website for Logic Express that there are "More than 1000" sampled EXS instruments, including "strings, horns, woodwinds, guitars..." etc. The only EXS instruments that I've been able to find are synthesizers. Where are the other EXS instruments and how can I access and use them?

    Make sure that the keyboard is turned on before you launch Logic.
    In the system preferences of the computer is it connected?
    In the preferences of Logic, does it give you an option in the audio section to use the driver in your keyboard? That should come up if its connected

  • TS3744 I updated I Tunes today and now I cannot open my I-Pod I Touch. The screen only shows the I tunes icon with the USB cable and an arrow pointint to the icon and I can't get it off of my screen or access my home screen   Help!

    I updated I tunes today , now I am unable to open my I Pod I Touch, the screen shows the I Tunes logo with a USB cord and arrow pointing back up to the icon, can't access my Home page

    The screen indicates that your device is in recovery mode.  It has to be restored by connecting it to a computer with itunes.  Restore to factory settings.
    This happens sometimes.  Hopefully you have a backup.
    HTH

  • Audio problems with an USB interface

    Hi everyone, this is my first post and glad to finally do it.
    I am so pleased with arch linux, it's just simply amazing. I have learnt a lot following the wikis, it's pretty simple and effective.
    I managed to install and configure ssh server, samba server (surprisingly easy), usb samsung laser printer, nvidia drivers, KDE desktop (so fast in arch), fonts, cpu scaling and I'm so happy with the results and perfomance.
    The only problem I ran into is about audio, I think the wiki on audio is pretty  incomplete (don't get me wrong I enjoy your work).
    The problem is with an USB interface line 6 toneport gx (http://line6.com/toneportgx/), I know the device is meant to be an usb guitar interface but since I don't longer play guitar I use it as soundcard. As complementary information it works with no problem on Ubuntu 10.04 (which is the distro I came from).
    The interface works and it's unmuted since I dmix does not work when I try to play sounds from different sources I had to install pulseaudio. Pulseaudio works partially, the sound was improved and finally I am able to play different sources. The big problem is when high cpu load ocurrs the the audio dies and does not come back even when the cpu loads decrease.
    Any help is appreciated.
    Thanks.

    You may want to debug pulseaudio (check their wiki to see how, involves running pulseaudio in verbose mode) to see what happens.

  • I tried to install the new iOs 7 on my iphone 4, but it wasn't completed (showing error 4005). Now, my iphone is stuck on the itunes' logo with the usb cord, and I can't use my phone. And itunes doesn't detect my iphone when I connect it on my computer.

    Hi everyone! I tried to install the new iOs 7 on my iphone 4, but it wasn't completed (showing error 4005). Now, my iphone is stuck on the itunes' logo with the usb cord, and I can't use my phone. And itunes doesn't detect my iphone when I connect it on my computer, so I can't put it in recovery mode or someting like that... What can I do?? I tried everything they tell me to do in the apple support but nothing seems to work. Thank you!

    No problem, glad to help!
    Update: my PC USB hub was connected to a USB 3 port, I connected the 30 pin cable directly to my PC, And the restore worked just fine. Restored phone from iCloud backup and seems to be working fine.

  • BadRequest: Virtual machines with secondary network interfaces and virtual machines with no secondary network

    I'm trying to create an "ExtraLarge" VM with multiple NICs.  The New-AzureVM returns the following error:
    BadRequest: Virtual machines with secondary network interfaces and virtual machines with no secondary network
    interfaces are not supported in the same deployment, also a virtual machine having no secondary network interfaces
    cannot be updated to have secondary network interfaces and vice-versa.
    But I have no other VMs.  Or at least I did and then deleted them and all their disks.  The service has no deployments (either staging or production).
    Why is New-AzureVM complaining about a mismatch of VMs with and without secondary network interfaces when no other VMs exist?
    I have tried many things to fix this, including the deletion of ALL of my resources.  I have deleted and created the service many times, both with an affinity group and without.  I have a screen print of the -debug output if your interested.
    Thanks for the outstanding help.

    Hi Ron,
    IMPORTANT NOTE: Please do not post the CONFIDENTIAL DETAILS ever on the public forums, this is HIGH RISK action.
    Please send an email with your contact details to my email
    [email protected] so that I guide you on steps which help you come out of the current scenario. Thank you for understanding.
    I suggest you to create a new VNET and new VM with cloud services. Create Multiple NIC VM. Let us know the results.
    Ref:
    http://azure.microsoft.com/blog/2014/10/30/multiple-vm-nics-and-network-virtual-appliances-in-azure/
    http://blogs.technet.com/b/canitpro/archive/2014/11/04/step-by-step-create-a-vm-with-multiple-nics-in-azure.aspx
    If you are unable to create a VM with multiple NIC, please open a support case as it requires more confidential information which is out of scope of FORUM support offerings.
    Regards,
    Girish

  • Help with opening Adobe Reader and downloading updates

    I can not open Adobe .pdf files any longer (this started yesterday, prior to that I could open adobe files).
    When I double click a .pdf file I get this notice on my screen: Windows cannot access the specified device path or file. You may not have the appropriate permission to access file.
    So I went to the Adobe download site to download a new copy of Adobe.  When I start the download I get this on the screen:  The instruction at "0x0e3a0068" referenced memory at "0x0e3a0068."  The memory could not be written.  Then two options are listed: click OK to terminate or cancel to debug.  So I click on cancel and I get this on my screen: Internet Explorer has closed this webpage to help protect your computer.   A malfunctioning or malicious addon has caused I.E. to close this webpage.
    I don't have AVG running, I do have avast but I've disabled it.  I ran Registry Mechanic and an I.E. erasure program but nothing helps.
    I have gone into I.E. and reduced the security level to its lowest state but no joy.
    So, any ideas or suggestions on what's the problem and how to overcome it would be appreciated.  Thanks, in advance, for your reply.  Jim R.

    Hi Mike..tried that as well but no joy.  A friend of mine was looking at it all and noticed that it was an I.E. thing as far as not letting me redownload the reader so I went to Mozilla Firefox and I could download a new version but....whenever I attempt to open a .pdf file I get that message, "Windows can not open the specified device, path or file. You man not have the appropriate permissions to access the item." 
    Damn...this is irritating as I need to get to some of thos files as I need them for a Journal I'm working on as editor-in-chief. 
    It all worked just fine last Saturday but starting Monday when I was on my flight out to D.C.  no joy. 
    Sigh...Jim R.
    Jim R.
    Date: Tue, 1 Dec 2009 14:50:27 -0700
    From: [email protected]
    To: [email protected]
    Subject: Help with opening Adobe Reader and downloading updates
    Under the help menu, there is an option to repair the installation of reader. Did you try that?
    >

  • I have an Apple MacBook Pro with 2 USB ports and a MiniDisplay Port. I also have an HDTV with a HDMI port. How can I use the TV as a display without any tethering wires between my computer and the TV?

    I have an Apple MacBook Pro with 2 USB ports and a MiniDisplay Port. I also have an HDTV with a HDMI port. How can I use the TV as a display without any tethering wires between my computer and the TV? I have a MiniDisplay Port to VGA adapter, but there are two issues with it: The new display doesn't have a VGA port, and even if it did, I wouldn't want to have my mac constantly attached to the display by a cable. I was looking for a way to use the TV as a display without any wires. Is there some type of bluetooth setup I could use? Please let me know if you have any suggestions.

    As I wrote above, I think you should look into the Apple TV yourself. The best place to find information about what it can and can't do and to ask your own specific questions is probably in the Apple TV forum, here:
    https://discussions.apple.com/community/appletv/appletv

  • New iPod nano, comes with a USB cable and CLIP? Whats it for?

    My new ipod 2gb nano comes with a usb cable and a little clip or stand type thing that the nano can sit in and at the bottom has a hole that the usb wire sort of fits through but it isn't made to sit on the desk, its more like a clip of something, any ideas what this is or how to use it?

    The extra piece is the adapter for the Universal Dock. The dock has a well in it and there's an adapter for each size of iPod that goes into it.

  • Need help with my iPhone 5 and my Macbook Pro.

    Need help with my iPhone 5 and my Macbook Pro.  I was purchased some music on itunes at my mac. Some reason I deleted those music from both on Mac and iPhone 5.  Today, I went to my iPhone iTunes store inside of iCloud to redownload my puchased. But those song won't able to sync back to my iTunes library on my Mac.  Can anyone help me with that ??....
    iPhone 5, iOS 6.0.1

    You've posted to the iTunes Match forum, which your question does not appear to be related to. You'll get better support responses by posting to either the iTunes for Mac or iTunes for Windows forum. Which ever is more appropriate for your situation.

  • Barbara Brundage, can you help with PS Elements 11 and Epson R2000 printer issue?

    Seeking help with PS Elements 11 which does not work with Epson r2000 printer.  Epson tech support could not fix, said it is PS e11 problem.  Receive prompt on PS e11 screen when I try to print stating "not compatible or settings are not correct.  Have set PS to manage color and printer manages color to off.  Would appreciate any suggestions.  Thank you.

    Hi,
    Sincerely appreciate your help.  Running Windows 7 on a  Dell XPS420.  System has been very stable for years.  Before purchasing the Epson r2000, I owned an r1800 which was an excellent printer but after seven years started to exhibit paper feed problems.  The r1800 worked with all applications and I was well satisfied with the saturation, contrast, etc. printing mostly 8x10 and 11x17 prints. 
    Thank you for the information about the # of installs for PS E11, will try uninstall/reinstall this morning.
    Will let you know how things go.
    Richard
    Date: Thu, 12 Sep 2013 19:47:38 -0700
    From: [email protected]
    To: [email protected]
    Subject: Barbara Brundage, can you help with PS Elements 11 and Epson R2000 printer issue?
        Re: Barbara Brundage, can you help with PS Elements 11 and Epson R2000 printer issue?
        created by Barbara B. in Photoshop Elements - View the full discussion
    What operating system are you using?
         Please note that the Adobe Forums do not accept email attachments. If you want to embed a screen image in your message please visit the thread in the forum to embed the image at http://forums.adobe.com/message/5678022#5678022
         Replies to this message go to everyone subscribed to this thread, not directly to the person who posted the message. To post a reply, either reply to this email or visit the message page: http://forums.adobe.com/message/5678022#5678022
         To unsubscribe from this thread, please visit the message page at http://forums.adobe.com/message/5678022#5678022. In the Actions box on the right, click the Stop Email Notifications link.
         Start a new discussion in Photoshop Elements by email or at Adobe Community
      For more information about maintaining your forum email notifications please go to http://forums.adobe.com/message/2936746#2936746.

  • HT1473 I recently update my iphone and now is not allowing me to access my contacts, emails etc. When I try to switch it on it has an itunes symbol on the front with the usb plug and an arrow. What do I do to get my contacts etc back and make phone calls?

    I recently update my iphone and now is not allowing me to access my contacts, emails etc. When I try to switch it on it has an itunes symbol on the front with the usb plug and an arrow. What do I do to get my contacts etc back and make phone calls?

    To be more clear:
    Was you phone hacked/jailbroken BEFORE you hooked it up?

  • My Iphone 5 suddenly turned off and there is only the Itunes logo with the usb image and arrow key. I've now connected to Itunes but it doesn't work

    My Iphone 5 suddenly turned off and there is only the Itunes logo with the usb image and arrow key. I've now connected to Itunes but it doesn't work

    Have a look through this Doc
    http://support.apple.com/kb/TS3281

  • HT4623 i updated my iphone 4s to the new ios 6.1.3 after installing it the device displayed itunes with a USB symbol and cannot come up. please any ideas

    i updated my iphone 4s to the new ios 6.1.3 after installing it the device displayed itunes with a USB symbol and cannot come up. please any ideas

    Do as the diagram indicates:  Connect your iPhone to your computer.  Open iTunes on the computer and restore your device.

Maybe you are looking for

  • Will the old 23" ACD work with the Mini DisplayPort to Dual-Link DVI Adapte

    Will the old 23" ACD work with the Mini DisplayPort to Dual-Link DVI Adapter and the new MacBook Pro? Apple Store says it is for the 30" only. Thanks ... Ken

  • Safari issue with cascading style sheets

    I've been using the beta version of Safari 4.0 for weeks with no problems. Now the final version seems to have totally messed up what appears to be cascading style sheets on my blog. My blog looks perfectly fine on other browsers as well as on the ol

  • Properties Tab in WAD

    Hi Sapmates,      Could any one tell me how to hoe to reset prorties area in WAD. there will be three areas in WAD right, so by mistake i closed properties area hu can i reset the properties area. Point will be rewarded. Regards Sujan

  • CHARM: Administrative Maintenance in Prod.System

    Hey, I want to do some changes in my productive system, w/o involving the dev.system. I know, that I have to create a Admin.Maintenance-Correction in CHARM. Everything seems to be working. By clicking "log in in system" a new gui opened in the same p

  • How to get back crash diagnostics warning?

    How do I re-enable the "ask before sending" crash diagnostics option? I selected the "do not ask again" box but want to change my mind so it asks each time before sending the diagnostic info to Apple. In iTunes, right-clicking on the iPhone icon reve