Help with motion detection preset on a WVC210

Hi, I am really out of ideas. Is it possible to set the home position as my motion detection area? I can't seem to be able to make my camesa stay at its home position. I set my camera to go back to my home position after 1 minute of idling, the the camera keep going somewhere else. I noticed that the area it goes to is the same area that my camera goes to when I clicked on the motion icon (the one with the man running. Can I overwrite that position? I tried deleting all my presets, recalibrated the camera and even resetting my camera a few times already. I really need help cause the area that the camera choose as my motion area is not what I need. Thank you in avanced to all that take the time to answer me.

Hi, yes I can manually tilt up or down. I have the camera facing down on the stairs to the entrance of my house and saved as a home position. I went in to the motion detection section and made sure the position is the same as my home position (I hit apply just to be sure). I set my camera to go back to my motion detection area when idle for 5 minutes (I tried different values already). Within 5 minutes the camera would tilt back to the center (facing the street), but it seems that the panning position was saved. I can move the camera around. When I hit the home position the camsera would go back to where I want, but when I hit the motion button the camera would be in the same panning position, but with a different tilt position center). The reason I know its the center is because I tried resetting my default home position and it would go back to the center pan/tilt position. It seems the camera would not accept any tilt position other then the center... I can give you access to my camera if you would like. I greatly appreciate your time and effort in helping me.

Similar Messages

Pvc2300: false positive with motion detection

Hello!
I bought 3 pvc 2300 cameras. I tried motion detection with camera's software and with "Active webcam" software and I received a lot of false positive mails.
1. with camera's software, I set event with motion detection & sent mail, but I receive a lot of mail when there isn't motion (I saw registrations and images)
2. with Active WebCam software I use Linksys cameras and Panasonic Cameras. With Panasonic cameras all is ok. With Linksys cameras, about every hours there is a black frame, so I receive a mail from motion detection. Black frame arrive about every hours, after 60 minutes from last black frame. That is very strange!
I changed sensitivity, check frequency, number of frame at second, but I have same problem.
Can you help me?
Thanks
Mary

I have 2 Panasonic cameras too and I need one software to manage all cameras.
sensitivity: on active webcam software, I changed sensitivity of motion detection
frequency check: on active webcam software, I changed from check motion every 0,1 second to every 5 seconds
number of frame: on Linksys software I changed Max Frame Rate from 15 fps to 6 fps.

WVC210 with Motion Detection does not stay in the correct position

When I set the camera in a specific position (setting it as Home) and then I enable Motion Detection feature (setting area and sensibility using the home position); if i have set the "Disable Motion Detection while position is incorrect" with "Go to Motion Detection position if idle" option the camera will reset the tilt after the time set has expired.
Is it a known bug (I have not found anything about that here)?
Is there a way to set which is the motion detection position to be held?

Hi M.Bordoni,
I will pass this onto the wonderful folks at the Small Business Support Center to get their opinion.
Just out of interest, I'm guessing you are utilities built within the camera to send a image somewhere ?
Are you using the free Surveillance monitoring application to store captured video on your NAS/PC or server ?
regards Dave

Please help with Motion Crashes.

Hello Mac People:
I recently purchased a new MacBook Pro and I was excited to have a faster machine to edit video on than my several years old iMac with less memory, older graphics card etc. But, alas, my new machine keeps repeatedly crashing on a Motion project that the old Imac will still work with - export, etc. I've tried to figure out what the problem is... but haven't done any reinstall and etc. Below I've posted the latest crash report and I was wondering if anyone can help me understand how to read it, and if it might point to where the issue lies within my beautiful new machine. Both machines are running the latest version of Motion I believe.
My computer has the NVidia GForce graphics cards - both 9400M and 9500GT and has the 3.06 Ghz Intel Core 2 Duo with 4gb ram.
Thanks so much!
Process: Motion [335]
Path: /Applications/Motion.app/Contents/MacOS/Motion
Identifier: com.apple.motion
Version: 4.0.2 (726)
Build Info: Motion-7260000~10
Code Type: X86 (Native)
Parent Process: launchd [77]
Date/Time: 2010-07-29 13:12:13.265 -0400
OS Version: Mac OS X 10.6.4 (10F569)
Report Version: 6
Interval Since Last Report: 259686 sec
Crashes Since Last Report: 18
Per-App Interval Since Last Report: 7681 sec
Per-App Crashes Since Last Report: 12
Anonymous UUID: BF617FBC-342F-4BEC-BFD2-CFA9FDF30CE3
Exception Type: EXCBADACCESS (SIGBUS)
Exception Codes: KERNPROTECTIONFAILURE at 0x0000000000000007
Crashed Thread: 0 Dispatch queue: com.apple.main-thread

This is a continuation of my previous post... I'm getting two kinds of crashes... sometimes Motion crashes on start-up and sometimes it crashes while I'm working with this particularly project. The latter crash report says that "thread 7" crashes. While I'm not sure what that means... here's the report for thread 7. Thanks for any advice!!!
Thread 7 Crashed:
0 com.apple.GeForceGLDriver 0x8f0629f3 gldAttachDrawable + 2579
1 com.apple.GeForceGLDriver 0x8f124615 gldUpdateDispatch + 15381
2 com.apple.GeForceGLDriver 0x8f124980 gldFlush + 80
3 GLEngine 0x025c5c36 glFlushRender_Exec + 57
4 com.apple.QuartzCore 0x98677f81 feaccel_contextflush + 33
5 com.apple.QuartzCore 0x98677f49 feaccel_contextrelease + 34
6 com.apple.QuartzCore 0x9867b828 fegl_bufferupdate + 172
7 com.apple.QuartzCore 0x9867b759 feglbegin + 76
8 com.apple.QuartzCore 0x98623cd0 fetree_render_apply1 + 1453
9 com.apple.QuartzCore 0x9861e9c7 fetree_renderapply + 1657
10 com.apple.QuartzCore 0x9861d213 fetree_render + 1885
11 com.apple.QuartzCore 0x9861c75a fetree_rendertree + 185
12 com.apple.QuartzCore 0x9860ac32 fetree_renderimage + 1017
13 com.apple.QuartzCore 0x9860a4d2 feimage_render + 289
14 com.apple.QuartzCore 0x98674e54 feimagerender + 155
15 com.apple.QuartzCore 0x986bfdcc renderImage + 109
16 com.apple.QuartzCore 0x98673874 -[CIOpenGLContextImpl renderWithBounds:matrix:function:info:] + 209
17 com.apple.QuartzCore 0x9867379b -[CIContextImpl render:] + 207
18 com.apple.QuartzCore 0x986705c9 -[CIContext drawImage:inRect:fromRect:] + 1105
19 com.apple.fxmetaplug.ImageUnit 0x077622e9 DummyCGDataProviderReleaseInfoCallback + 3099
20 com.apple.fxplugframework 0x01c0c409 -[FxSample evaluateWithOptions:] + 253
21 com.apple.fxplugframework 0x01c0ad59 -[FxPlug renderImageOutputAtTime:withOptions:inFxContext:inRegionOfInterest:] + 189
22 com.apple.ozone.framework 0x00acc7b8 OZFXPlugGenerator::getHelium(LiAgent&, float, OZRenderParams&) + 3112
23 com.apple.ozone.framework 0x00c51a47 OZLiCiGenerator::getHelium(LiAgent&) + 103
24 com.apple.Lithium 0x0164e895 LiAgent::getHelium(LiImageSource*) + 4789
25 com.apple.Lithium 0x0165ec61 LiPolygonInstance::makeNode(LiClipSet const&) + 1713
26 com.apple.Lithium 0x01684841 LiRenderInstance::collectGeode(LiGeode*, LiCollectState&) + 913
27 com.apple.Lithium 0x01685649 LiRenderInstance::collect3D(LiSceneObject*, LiCollectState&) + 1385
28 com.apple.Lithium 0x01685a9b LiRenderInstance::collectGroup(LiGroup*, LiCollectState&, LiCollectState&) + 427
29 com.apple.Lithium 0x0168570c LiRenderInstance::collect3D(LiSceneObject*, LiCollectState&) + 1580
30 com.apple.Lithium 0x01685a9b LiRenderInstance::collectGroup(LiGroup*, LiCollectState&, LiCollectState&) + 427
31 com.apple.Lithium 0x0168570c LiRenderInstance::collect3D(LiSceneObject*, LiCollectState&) + 1580
32 com.apple.Lithium 0x016874f1 LiRenderInstance::collect() + 2129
33 com.apple.Lithium 0x01687abc LiRenderInstance::buildHeliumGraph(LiAgent&) + 524
34 com.apple.Lithium 0x01689d36 LiRenderInstance::getHelium(LiAgent&) + 294
35 com.apple.Lithium 0x015e56e3 LiRenderer::getHelium(LiAgent&) + 51
36 com.apple.Lithium 0x0164e895 LiAgent::getHelium(LiImageSource*) + 4789
37 com.apple.ozone.framework 0x0091f6a8 GLRenderer::getSceneHeNodeFromLiWorld(OZScene*, OZSceneSettings const&, OZRenderParams&, PCPtr<LiGroup>, HGRenderer*, int, int, double, double, long*) + 2312
38 com.apple.ozone.framework 0x009252ac GLRenderer::getFrameNodeForSingleTime(OZScene*, OZRenderParams&, HGRenderer*, double, double, long*) + 940
39 com.apple.ozone.framework 0x00925ec7 GLRenderer::getFrameNodeIncludingFields(OZScene*, OZRenderParams&, HGRenderer*, long*) + 999
40 com.apple.ozone.framework 0x00926844 GLRenderer::getFrameNode(OZScene*, OZRenderParams&, HGRenderer*, long*) + 164
41 com.apple.ozone.framework 0x00c986b4 OZRendererBuilderUnit::processRenderInstruction(OZRendererBuilderInstruction*) + 1412
42 com.apple.ozone.framework 0x00c98be9 OZRendererBuilderUnit::execute() + 25
43 com.apple.ozone.framework 0x009620d5 OZExecutionUnit::executeLoop() + 197
44 com.apple.ozone.framework 0x0096215e OZExecutionUnit::executeLoopWrapper(void*) + 94
45 com.apple.procore.framework 0x019020a8 PCThread::startup(void*) + 18
46 libSystem.B.dylib 0x92dde81d pthreadstart + 345
47 libSystem.B.dylib 0x92dde6a2 thread_start + 34

Help with Motion Tracking and Masking?

Hi. First and probably only post here. I've got a bit of an issue....
I'm trying to create "snapshots" in my video that are created from masks which are then motion tracked and remain stationary. Here's a video of what i'm talking about... http://www.youtube.com/watch?v=9OhVAduuJc8
The problem I'm running into is that after i motion track the layer, select a null object as the target, duplicate the video layer, mask the object, freeze frame, and pair it to a null layer, the object does not remain stationary as the ones in the video do. Instead it moves WITH the null object and I cant figure out why. I've gotten a tutorial from the guy who made the video, however it's private so i don't know if you guys will be able to see it. http://www.youtube.com/watch?v=zY0QLrMCcGM
Either way, i followed the tutorial exactly and still to no avail. Are my settings messed up or what exactly is going on? Ive successfully done this project before but now that i'm using CS5, i'm running into these issues. If anyone has any advice i'd gladly try it out and return with the results.
Thanks so much for trying to help me out.

Yeah the null is still moving. Will freezing it lock the mask into place while still allowing the footage to play through? And how would i go about "freezing the null"?
I just dont understand how this person does it in the tutorial, and the mask remains in place. I know you probably can't watch the tutorial cause the user has it set as private, but as far i know his mask stays in place, but uses the null (while still moving) as a tracking device to keep the mask from floating out of control as the camera moves through the shot.
Sorry if I'm making this rather confusing. It's difficult to explain.
Maybe it might be easier to explain how you would obtain the result from the video I've posted? Keep in mind I dont have CameraTracker.

I need help with motion control. I am programming in Visual Basic. I will need help with what parts I need to purchase from NI, along with help on the code.

I am using a Papst servo motor and I need to know where to start and what to purchase to get this motor to spin. I am using visual basic and in my program I calculate the direction and RPM's needed from the motor. It will spin anywhere from 1 to 10000 RPM's. It seems rather easy, but I have no idea on how to spin the motor at the specific RPM, and stop it with a command stop in the program. Please help.

We really should know a little more about your intended uses for this system, but assuming you want to do relatively simple (or even not so simple!) motion, you'll need a few components...
A motion controller, such as the PCI-7342, can take your VB commands and turn them into the commands needed to "run" the motor. Next you'll need a drive, such as the MID-7342. This includes the servo amplifier that actually powers the motor. It also has connections to "pass through" the encoder signals from the motor back to the motion controller.
The above-named pieces assume one or two axes of motion. You'll also need a cable to connect the two (can't remember the model right now). You can use MAX to configure the motion controller, and there are just a few VB calls you
'll need to make using NI-Motion functions to define the motion and get it going.
Hope this helps!

Need Help With Motion Track/Camera Tracking

I've been trying for several days to motion track 2 seconds worth of footage but I cannot get it. I've tried the AE motion track, 3D Camera Tracker, Mocha Pro, Camera Tracker from the Foundry, Boujou (could be user error with that though, cause I had never used it before), but I cannot get this shot figured out. Test - YouTube here is a link to the footage, I'm trying to track from frame 183-235 (where the guy is kneeling down in front of the box holding dynamite and everything is black and red)
Any help would be great, all I want to do is have an image attached to one of the boards in the background so it doesn't move.
Thanks!

Wow you have boujou? Thats awesome $10k, anyway looks like mocha should be fine for this as I don't see a ton of camera movement in that shot where you want to track. Do you know how to use mocha? If not there are tuts while working on that scene. Here's a few http://cgi.tutsplus.com/articles/advanced-motion-tracking-with-mocha-ae--ae-15231 and for various tracker apps including the built in one http://cgi.tutsplus.com/articles/26-tracking-and-matchmoving-tutorials--ae-7394

Help With Motion to Vacate

I have satisfied one of the two judgments on my credit report with Schewels Furniture Company. I have been trying to find an example online with how to fill out the Motion to Vacate form for Virginia and haven't had any luck. I called the credit manager today, asked if she could do that for me, but, she said that was up to me to file. So, I downloaded the form from the courts website for VA and have filled in some of it. There is a section for the plaintiff and defendant. Since I am the one filing, am I the plaintiff? I can't afford an attorney and wish I had something to look at to see how it's filled out. I'm worried I'll make a mistake. I thought about asking their attorney, but, they didn't use one. She just filed the judgment herself. Thank You

Well, here is how my trip to the courthouse went, yesterday, when I attempted to file my Motion to Vacate form in Virginia. On the way down, and while filling out the form at home, I worried about numerous things that could go wrong, but, the one thing that did go wrong never entered my mind. I approach the clerk's window and she gets up from her desk to come over and ask if she can help me. First, I ask and pay for a copy of the original judgment so I can make sure that I have the plaintiff's address written correctly on my Motion form. Then, after I'm done with that, I tell her that I would like to file my Motion to Vacate and ask how much is the filing fee. She doesn't know, so, she takes my form and goes to talk to two of the other clerks at their desks in the back of the room. She comes back and says there isn't a fee to file. I thank her and say I'd like to go ahead and file the form please. I can see a look of confusion coming over her as she slides my form back to me and says...'I'm only trying to help, but, I believe that this type of form is for the plaintiffs to file...not the defendant. Maybe you should contact an attorney and ask for their counsil on this.' I explain that I cannot afford an attorney, however, in my research, I discovered that I can file this Motion asking the judge to vacate, or remove, the judgment from my credit report. I told her that I had asked the plaintiff, Schewels Furniture, if they would do this and their response was that I had to file this form; they had done their part by sending the Satisfaction of Judgment notice to her office. So, it goes back and forth like this for several minutes, and in the end, she simply will not take the form because she believes I would be wasting my money(she found out that it's $12 to file), that the Satisfaction of Judgment is all I need for removal of said judgment on my credit report(I told her that Experian needs the Motion to Vacate signed by the judge), and says again that I need to speak to an attorney. I know she was trying to help me. I'm just frustrated. I'm going to call around anyway to see if I have filled out the plaintiff vs defendant part correctly as that was what she was stuck on in her reasoning. Because I had Schewels Furniture in the plaintiff spot, she thought it was wrong. And, how was y'all's day yesterday? Lol.

Need help with Motion Tracking-button in After Effects CS6

Hello I just bought After Effects cs6 and wanted to try ''motion tracking'' but I just can't push the motion tracking button. Is there anyone who can help me with that problem?
Responses are highly appreciated!

In order for the motion tracking buttons to become highlighted, you first need to select the clip you'd like to track in the timeline:

Always-on webcam chat with motion detection?

Also found this which requires two ipads (or iphones): https://perch.co/2015-features/
This would be even easier though the initial spend on refurbished ipads is higher, but still long term this is better because you are having to keep a dedicated PC station with its monitor/speakers/etc. And this way they can carry me around the office and into team meetings.

Does anyone know of a chat/webcam solution that detects motion? The idea is I am putting a Virtual Me in my office because I am moving out of state and support the office remotely. No joke!
The idea is they walk into my former office space, the webcam detects the motion and alerts me at my remote location, and then we chat almost as if I'm still there...
We also will be using Skype for Business but this is more like a chat station.
This topic first appeared in the Spiceworks Community

Help with Motion Tweens and Designing

So we are basically trying to design part of a website
and we want to have the whole alphabet at the top of the page then we want like one letter to shake
and then fall into a funnel which we want to be in the middle of the page then another letter shakes, then two at a time, the three at a time and after that all the letters fall in.
After that we want the letters to fall out and form and sentence, a few sentences.
That's basically all that was thought about, and we are new to flash so we were looking for any tips, or any help to actually do this
we were trying to mess wit the motion tween but we never figured out how to make it shake how we want it to, so any help will be appreciated.

var growFactor:Number = 0.01;
var shakeFactor:Number = 0;
var xDirection:int = 1;
var yDirection:int = 1;
var control:Number = 2.0;
var MOrigin:Number = M.x;
var OOrigin:Number = O.x;
var IOrigin:Number = I.x;
var TOrigin:Number = T.x;
function shakeIt(evt:Event):void {
     // move A
      M.x = MOrigin + Math.random()*shakeFactor*xDirection*control;
      M.y = MOrigin + Math.random()*shakeFactor*yDirection*control;
      O.x = OOrigin + Math.random()*shakeFactor*xDirection*control;
      O.y = OOrigin + Math.random()*shakeFactor*yDirection*control;
      I.x = IOrigin + Math.random()*shakeFactor*xDirection*control;
      I.y = IOrigin + Math.random()*shakeFactor*yDirection*control;
      T.x = TOrigin + Math.random()*shakeFactor*xDirection*control;
      T.y = TOrigin + Math.random()*shakeFactor*yDirection*control;
      // flip coins to see which way to move things next time
      if(Math.random() < 0.5){
            xDirection *= -1;
      if(Math.random() < 0.5){
            yDirection *= -1;
      // shake a little more each time
      shakeFactor += growFactor;
M.addEventListener(Event.ENTER_FRAME, shakeIt);
O.addEventListener(Event.ENTER_FRAME, shakeIt);
I.addEventListener(Event.ENTER_FRAME, shakeIt);
T.addEventListener(Event.ENTER_FRAME, shakeIt);
The problem is that M is shaking in place where i put him and anothers letters are in strange position down look here http://robinmd.nm.ru/new/Untitled-1.html I wold like to put them on one x line whats wrong in the code?=)

Need Help with peak detection

Hello,
I am in need of some help using the peak detection. I have an array of values that I need to find the centroid (peak) of. I am only interested in finding the centroid of a large peak. The problem I keep having is that the peak detection VI finds every little peak above the threshold when I really want the overall average peak. Please look at the graph in the picture file to see what I mean.You can see that the main peak has jagged edges. The peak detection in Labview will find every one of these jagged edges and report the location back as a peak. I am only interested in the overall shape of the peak. How can I filter out the multiple peaks and only report the centroid of the desired shape? There is an example program in the labview package called "advanced peak detection point by point" but I cannot figure out how to employ it in this application.
Thanks in advance for any help.
-Mark
Attachments:
Array values.PNG ‏9 KB

If I were you, I wouldn't even use peak detection.
The point of peak detection is to find multiple peaks, like in a sine wave, etc.
If you just want the maximum:
Just use 'Array Max & Min'
The 'max value' equates to your y-value.
The 'max index' can be used to find your x-value
Message Edited by Cory K on 05-07-2009 11:52 AM
Cory K
Attachments:
Peak.PNG ‏3 KB

HT4591 Help with Motion 5, frame rate ridiculously low

I'm very new to Motion, and every time I try to import a video from my iPhone, which has 30 fps, the little fps displayer says it only has 6-10 fps currently. Why?
I don't really understand this...

hi,
it might have something to do with the codec that the iphone captures in. If its an h264 based codec, these were not designed ot edit with and maybe Motion doesnt like it. Try transcoding to prorez. Also not sure what machine you have or how much RA,, or what your project size is, all these will effect performance.
adam

Motion Detection on Linksys WVC54GCA

Sorry if this is in the wrong section.
I would appreciate if someone could help me with this.
I am trying to configure this camera to record onto my network drive via FTP on a schedule - for example 9 - 5 each day.
Can recording be done based on these entered times or does motion have to be detected?
I have copied a screenshot of my settings at below url:
http://img23.imageshack.us/img23/15/settingsr.jpg
I have tried with passive mode enabled and disable and tried recording with a shorter internal between start and end times.
FTP credentials are correct, along with IP. I can access both locally and via the internet.
Thanks for your help.

The motion detection should be enable and the motion will be detected with-in the specified period of time.

WVC54GCA motion detection and port 25 blocked

About a month ago, I stopped receiving motion detection emails believe its because ISP is now blocking port 25...can successfully send and receive test emails but do not receive any messages with motion detection...can anyone suggest a solution to this problem, thanks much

I just encountered that problem and this link helped me with it..

Help with motion detection preset on a WVC210

Similar Messages

Maybe you are looking for