Help with opening port 10000 on a pix 501

I am attempting to open port 10000 so that I can remotely VPN using tcp port 10000. This is a pix 501 running version 6.3.5.
What commands do I need to enter for this to happen?

Remote vpn access can be configured on a pix 501 by using the configuration guide present in the links given below:
Site-to-Site VPN Configuration Examples is present in the url below:
http://www.cisco.com/en/US/docs/security/pix/pix63/configuration/guide/sit2site.html
Managing VPN Remote Access giude is present in the following url:
http://www.cisco.com/en/US/docs/security/pix/pix63/configuration/guide/basclnt.html

Similar Messages

Need help with opening ports on airport extreme

My vonage phone is connected to airport extreme router, voice quality of phone calls was poor. Vonage tech support says vonage port on my airport extreme was closed and i need to open it.
Here is my chat details with vonage tech support-
The following ports are needed for Internet communication between the Vonage adapters and the Vonage servers.
SIP: Port 5061 UDP
RTP (Voice) Traffic: Ports 10000-20000 UDP. When a call is made, a random port between 10000 and 20000 is used for RTP (Voice) traffic. If any of these ports are blocked, you may experience one way or no audio.
Please do suggest me the way to open the ports on airport extreme
Thanks
Venki

Instructions for opening ports is here.
https://discussions.apple.com/docs/DOC-3415
You should be fine opening the whole range, 10000-20000

Help with opening ports on the Time Capsule

Ok, let me try to describe the situation I'm in. I use a local internet company and I have 2 computers hooked up to my TC, one being a mac and the other a PC. I use the mac for office stuff and my PC is for gaming. I just bought Call of Duty: Modern Warfare 2, and it won't allow me to connect, but I when I try connecting using a Sprint Smartview internet chip, it works but goes slow. So I know it has to do with the TC, now my Mac uses the Ip 10.0.1.201 and my PC is 10.0.1.4, I've tried opening up the ports with the port mapping tool in Airport Utilities but didn't have any luck. I don't want to ruin anything by wandering into things I don't understand ...
The ports needed are on this website
http://forums.steampowered.com/forums/showthread.php?t=1019454
Thanks in advance, I've been trying to figure this out for the last like 6 hours!

Ok, let me try to describe the situation I'm in. I use a local internet company and I have 2 computers hooked up to my TC, one being a mac and the other a PC. I use the mac for office stuff and my PC is for gaming. I just bought Call of Duty: Modern Warfare 2, and it won't allow me to connect, but I when I try connecting using a Sprint Smartview internet chip, it works but goes slow. So I know it has to do with the TC, now my Mac uses the Ip 10.0.1.201 and my PC is 10.0.1.4, I've tried opening up the ports with the port mapping tool in Airport Utilities but didn't have any luck. I don't want to ruin anything by wandering into things I don't understand ...
The ports needed are on this website
http://forums.steampowered.com/forums/showthread.php?t=1019454
Thanks in advance, I've been trying to figure this out for the last like 6 hours!

Help with opening Adobe Reader and downloading updates

I can not open Adobe .pdf files any longer (this started yesterday, prior to that I could open adobe files).
When I double click a .pdf file I get this notice on my screen: Windows cannot access the specified device path or file. You may not have the appropriate permission to access file.
So I went to the Adobe download site to download a new copy of Adobe. When I start the download I get this on the screen: The instruction at "0x0e3a0068" referenced memory at "0x0e3a0068." The memory could not be written. Then two options are listed: click OK to terminate or cancel to debug. So I click on cancel and I get this on my screen: Internet Explorer has closed this webpage to help protect your computer. A malfunctioning or malicious addon has caused I.E. to close this webpage.
I don't have AVG running, I do have avast but I've disabled it. I ran Registry Mechanic and an I.E. erasure program but nothing helps.
I have gone into I.E. and reduced the security level to its lowest state but no joy.
So, any ideas or suggestions on what's the problem and how to overcome it would be appreciated. Thanks, in advance, for your reply. Jim R.

Hi Mike..tried that as well but no joy. A friend of mine was looking at it all and noticed that it was an I.E. thing as far as not letting me redownload the reader so I went to Mozilla Firefox and I could download a new version but....whenever I attempt to open a .pdf file I get that message, "Windows can not open the specified device, path or file. You man not have the appropriate permissions to access the item."
Damn...this is irritating as I need to get to some of thos files as I need them for a Journal I'm working on as editor-in-chief.
It all worked just fine last Saturday but starting Monday when I was on my flight out to D.C. no joy.
Sigh...Jim R.
Jim R.
Date: Tue, 1 Dec 2009 14:50:27 -0700
From: [email protected]
To: [email protected]
Subject: Help with opening Adobe Reader and downloading updates
Under the help menu, there is an option to repair the installation of reader. Did you try that?
>

Help with firewall port opening

I'm a newbie at this, so please be patient. And my Time Capsule is less than a week old, so I'm still in the learning stages.
I purchased an iPod Touch and one of the programs from the App Store--Pocketpedia--requires certain ports to be open in order to sync with my Mac pedia programs.
I went into the Time Capsule>Advanced settings to try to open the appropriate 2 ports (one for the Powerbook and one for the Touch). I'm obviously doing something wrong. That wouldn't be heard since all of the terminology is foreign to me. I know that I need to open the two TCP ports.
I clicked on the + to add a new service/port. I wasn't sure if I needed the numbers in Public TCP ports or private, so entered them in both with the numbers separated by commas.
I thought that this would be "personal file sharing" so I tried to choose that under "Service". However, when I did that it said "A pulic TCP port number conflicts with a file sharing port on the base station. Disable file sharing or choose a different port number." Actually, once I choose "personal file sharing", it autofills in port 548 into the two TCP numbers. That's one that's opened within System Preferences. So it actually won't let me change that number at all. When I try to, it services menu defaults back to "choose a service".
Needless to say, I'm very confused. I did go ahead and create a service with the two port #'s and without designating it a specific "service", but that doesn't seem to fix my problem with allowing the Touch to sync with my Powerbook.
Any help would be much appreciated.

With port mapping (forwarding) you "open" ports on the router's firewall in order to allow Internet traffic to reach a host device on your local area network (LAN). In this case your iPod Touch and PowerBook. However, you can only map the same port(s) to only one device. For example, you cannot map port 548 to both the Touch AND the PowerBook, only one or the other.
The typical port mapping setup requires two basic steps:
1. Assign either a static IP address or reserve a DHCP-assigned IP address to the host device.
2. Map the appropriate port(s) on the router to this host device.
The following is a more detailed list of steps ...
To setup port mapping on the Time Capsule (TC), either connect to the TC's wireless network or temporarily connect directly, using an Ethernet cable, to one of the LAN port of the TC, and then use the AirPort Utility, in Manual Setup, to make these settings:
1. Reserve a DHCP-provided IP address for the host device.
Internet > DHCP tab
o On the DHCP tab, click the "+" (Add) button to enter DHCP Reservations.
o Description: <enter the desired description of the host device>
o Reserve address by: MAC Address
o Click Continue.
o MAC Address: <enter the MAC (what Apple calls Ethernet ID if you are using wired or AirPort ID if wireless) hardware address of the host computer>
o IPv4 Address: <enter the desired IP address>
o Click Done.
2. Setup Port Mapping on the AEBSn.
Advanced > Port Mapping tab
o Click the "+" (Add) button
o Service: <choose the appropriate service from the Service pop-up menu>
o Public UDP Port(s): <enter the appropriate UDP port values>
o Public TCP Port(s): <enter the appropriate TCP port values>
o Private IP Address: <enter the IP address of the host server>
o Private UDP Port(s): <enter the same as Public UDP Ports or your choice>
o Private TCP Port(s): <enter the same as Public TCP Ports or your choice>
o Click "Continue"
(ref: "Well Known" TCP and UDP ports used by Apple software products)

Need help with bus ports (pre or post?)

I have recorded my acoustic guitar on two tracks in order to save time with the drop region and cutting and I have already autonated both of the tracks so they sound like one guitar (same channel strips).
However, I am trying not to use the plug ins that are on the guitar tracks TWICE (they are verry powerful), so I would like to copy the channel strip of my guitar tracks to a bus track, yet still keep the autonation working for both tracks (by the way, its just volume after the plug ins).
I cant say I could esily put all the regions from both tracks into one, so I want to use a bus.
If this is at all possibe for me to do while keeping my automation for both of the two tracks, how would I go about doing this? (do I set them as pre/post sends, ect.)
Thank you so much!
-Sam

Instructions for opening ports is here.
https://discussions.apple.com/docs/DOC-3415
You should be fine opening the whole range, 10000-20000

Help With VNC Ports

Hello everyone. I have a PowerPC G4 Mac Mini with Mac OS X 10.4 Tiger. I have turned off the Apple Firewall and I do not have a router. I connect to the internet using a DSL Modem. OK, I am trying to set up a VNC Server Using OSXvnc. Well, I know i need port 5900 to be open, and there is nothing blocking this port from opening. I checked on www.grc.com to see if port 5900 was open, but it said the port was "Stealthed". Does anyone know how I can open port 5900? Thanks in advance for all of your help.

Could you try opening a Terminal window and typing the following command:
sudo ipfw list
(you'll be prompted for your password; you have to be an Administrator of your computer)
If your firewall is completely turned off, it should print a line like:
65535 4660828 3870352285 allow ip from any to any
If it's not completely off, you'll get a whole bunch of lines as output, some saying "deny ip" instead of "allow ip". That would be my best guess as to what's happening.
Also, I assume you haven't installed any third-party (non-Apple) firewall programs? A few do exist...
If the firewall is off, have you tried connecting via VNC, just to see if it actually does work?

Need help with open hub

Hi eveybody,
I was trying to wok with open hub. Created infospoke, destination i gave was a csv file named d:/openmara.csv path, saved and activated the info spoke. I went to d:/ to view the uploaded files, two file was created, when i try to open a file it says "unable to read" , when i tried to open the second one i could open the file and see some datas but not in a correct format, why is that?
Then i tried to load the data in database, so in the infospoke i selected the option for destination as database,saved and activated the infospoke, now where should i go to see the uploaded datas physically?
Could anyone help me with this.
Thanks,
RR.

Hi,
Thanks for the reply. I created a infospoke and destination was database option. Opened the se16 gave the table name which starts with /bic/....(please correct me if i am wrong),then the initial screen of se16 came up with all the fields , but when i executed it, the table is empty.Could you say why it is happening.
Thanks,
RR.

Help with Open Browser Window

I built a site named greenscapepump.com. I used the behavior
"Open Browser Window" that allows a photo to be viewed in a smaller
window. I have it set up to double-click the photo name to go to
the browser window. It works on some computers but not others. I
used the same behavior on other pages in the same web site and it
is working on all computers.
The three pages under the menu "Portfolio" are: Architectural
Fountains, Waterfalls and Streambeds, and Floating Fountains, are
the pages that have problems with this behavior on some computers.
Is this an individual computer problem, or do I need to do
something in Dreamweaver to fix it?

OMG - the code on the architecturalfountains page is a horror
Why do you need to use doubleclick.... most users are
accustomed to clicking
on a link wait for something to happen....
Also, the code for that dropdown is massive... are you really
committed to
that menu?
The validator found quite a few errors on that particular
page - I didn't
test each page (that's up to you :) these errors aren't
helping with your
page load also - one of the pages (can't recall which now)
just kept trying
to load and never did stop... try fixing the errors (some
more important
than others to the well being of your page) and then see
where you are at
with your pages... I'd also suggest changing the
'doubleclick' to just the
one click - really no need for anything else.
http://validator.w3.org/check?verbose=1&uri=http%3A%2F%2Fgreenscapepump.com%2Farchitectura lfountains.html%23
Nadia
Adobe® Community Expert : Dreamweaver
http://www.DreamweaverResources.com
|Tutorials|SEO |CSS Templates
http://www.csstemplates.com.au
http://www.adobe.com/devnet/dreamweaver/css.html
CSS Tutorials for Dreamweaver
"texasgranny" <[email protected]> wrote in
message
news:ef9h1v$4h8$[email protected]..
:I built a site named greenscapepump.com. I used the behavior
"Open Browser
: Window" that allows a photo to be viewed in a smaller
window. I have it
set up
: to double-click the photo name to go to the browser window.
It works on
some
: computers but not others. I used the same behavior on other
pages in the
same
: web site and it is working on all computers.
: The three pages under the menu "Portfolio" are:
Architectural Fountains,
: Waterfalls and Streambeds, and Floating Fountains, are the
pages that have
: problems with this behavior on some computers.
: Is this an individual computer problem, or do I need to do
something in
: Dreamweaver to fix it?

Help with Essbase Ports

Does anyone knows if you can set a specific port for each APP.
Before we had Essbase 5.0.2 and we have upgraded to Essbase 9.3.1.
Several users connect to different DB from the internet. We had configured 3 ports for access in the firewall, 33005, 33010 and 33015.
Each port was used to access a different DB,
DB A -> 33005
DB B -> 33010
DB C -> 33015
The problem that we have now is that every DB we start uses 2 ports, so when we start the 3 DB, the first one uses 33005 and 33010, the second uses 33015 and 33020 so the third can not be accessed through the internet.
I have try with PORTINC, but the main problem is that the open ports ends with 5, so I can not make the 3 DB visible.
So what I would like to know if you can assign an specific port to a specific DB.
I want to avoid any modification to the firewall, because that would mean I have to make a request to another area and that takes time.
Thanks in advance.

I don't believe the ports can be isolated to specific databases (unless the databases are isolated to individual servers, that is -- and you don't want that).
In version 5, the ports did use increments of 5. This is no longer the case though, since version 7, the default is now 1 (which makes a lot more sense now). You should open up a wide range for "other" reasons (mostly to avoid the issue with "unable to send/unable to receive" due to all available ports being in use). You should look at the technical reference for the PORTINC, SERVERPORTBEGIN, and SERVERPORTEND entries and match the firewall to the settings applied to the server.
Basically, the need to keep the number of ports to a minimum should be evaluated against the need to provide sufficient access. If this is a firewall issue that IT is restricting access to, you should consider VPN access security as an alternative to public exposure to the essbase server.

Please help with opening old mac AE file on a pc

Hi,
With the latest version of AE on a pc I tried opening older mac version .aep file created I believe in 1999. I had very little hope so I wasn't surprised to see this message:
"After Effects error: this file was created with an older version of After Effects [3.0 (Macintosh PPC)], and can’t be opened. You can convert this file using an older version of After Effect and resaving."
It is not clear which version should be used, Pc or Mac, and if at the end that file could eventually be opened in thet latest AE on a pc.
I will greatly appreciate any help with this.

Thanks Mylenium
Rebuilding is not an option. It is a lot of work and I need this as a portfolio item. I created a promotional interactive CD with Macromedia Director in 1999 for a sign company. I created 19 short animations for it with After Effects 3 using old PPC Mac. I haven't used After effects since then but recently several new clients asked me if I can make animations from that nature. So, I'm trying to use my old work as a demonstration of my creative skills. The problem is that the animations were rendered tiny with 309 x 228 pixels to fit in the interactive interface of the presentation intended for the small monitors used at that time. I took the animations from the interactive CD and using the latest AE on a pc, I created a rough composition with running the animations one after another. To make the animations a bit larger I scaled most of them to 320 x 240 hoping it will look better.
In my archives I have the project files and all .ai vector graphics used for the animations. I still have the old PPC Mac retired somewhere in the closets and installer CD with After Effects 3 and 4. I thought it would be great if I can somehow open the files in the latest version on a pc but if not I guess I have to take out that old mac are render to higher resolution using this ancient machine and AE version. And I'm wondering if all this is worth it.
I will appreciate any tips, advices, things to be aware, etc, and how to make this looks better on YouTube.
Oh, and another question by the way, I haven't been current to the animation software for a long time and wonder if this kind of presentational animations are best suited for creating with Flash or After Effects is still OK?

Problem with VPN by ASA 5505 and PIX 501

Hi
I have this scenario: Firewall ASA 5505, Firewall Pix 501 (with CatOS 6.3(5) ).
I have configured this appliance for Easy VPN (server is ASA) and PIX, and remote Access with Cisco client vpn (for internal lan ASA).
When i configure the ASA i have this problem, when i configure nat for easy vpn.
This is my nat configuration:
nat (inside) 0 access-list 100
nat (inside) 1 192.168.1.0 255.255.255.0
nat (inside) 1 0.0.0.0 0.0.0.0
nat (inside) 0 0.0.0.0 0.0.0.0 outside
when i put this command:
nat (inside) 0 access-list no-nat
this command is necessary for configuration of easy vpn, but the previous nat:
nat (inside) 0 access-list 100
is replace with the latest command.

To identify addresses on one interface that are translated to mapped addresses on another interface, use the nat command in global configuration mode. This command configures dynamic NAT or PAT, where an address is translated to one of a pool of mapped addresses. To remove the nat command, use the no form of this command.
For regular dynamic NAT:
nat (real_ifc) nat_id real_ip [mask [dns] [outside] [udp udp_max_conns] [norandomseq]]
no nat (real_ifc) nat_id real_ip [mask [dns] [outside] [udp udp_max_conns] [norandomseq]]
For policy dynamic NAT and NAT exemption:
nat (real_ifc) nat_id access-list access_list_name [dns] [outside] [udp udp_max_conns] [norandomseq]
no nat (real_ifc) nat_id access-list access_list_name [dns] [outside] [udp udp_max_conns] [norandomseq]

Problem with opening/port forwarding some ports but not others

I read the Faq and the first few pages of the forums but couldnt find anything.
I am using the Port Forwarding (WRT54G, Firmware 4.20.7) to my network camera to try to open up ports 80, 554, 5556 and 5558.
Using the network toolbox at Blackcode.com I then check the ports to see if they are open.
Port 554 seems to be open. Port 80, 5556 and 5558 do not appear to be open.
I am using the correct external IP address (I can toggle port 554 open and closed and test that). Toggling Blocking Anon Internet Requests Of/Off makes no difference to the result.
I have checked with my ISP and they dont claim to block those ports.
Any thoughts on what this could be? Is there a way to test if its my ISP? If it is my ISP, is there a workaround?
Thanks for any help.

Are you sure the camera does listen on those port at the time you did this tests? Are those ports open inside your LAN, too?
5556 and 5558 look like RTP ports which may only be active after the channels have been established through RTSP.
Forwarding of port 80 is known to be an issue on various routers as the router allocates port 80 for the web interface. Sometimes it helps to change the remote management port on the router from 80 to 8080 or something else. You may even have to enable remote management to get this active.
If this does not work you have to reconfigure port 80 on your server to a different port if possible.
Message Edited by gv on 08-21-2007 12:28 AM

Hi guys, I am having problems with open ports in OSX tiger

Hi, I have a home network and my computers have suspicious ports open, I dont know what they are , or if I have to close them or not.
Here is a local nmap scan
Starting Nmap 4.11 ( http://www.insecure.org/nmap/ ) at 2006-09-16 11:43 CLT
Interesting ports on 192.168.0.100:
Not shown: 1678 closed ports
PORT STATE SERVICE
22/tcp open ssh --> I enabled SSH for remote login into this one.
5000/tcp open UPnP ( what is this ?! )
Interesting ports on 192.168.0.101:
Not shown: 1678 closed ports
PORT STATE SERVICE
427/tcp open svrloc ( what is this ?! )
548/tcp open afpovertcp ( have to disable file sharing here)
MAC Address: 00:05::3A (Apple Computer)
Interesting ports on 192.168.0.102:
Not shown: 1676 closed ports
PORT STATE SERVICE
427/tcp open svrloc( what is this ?! )
548/tcp open afpovertcp (have to disable filesharing... TOO)
3689/tcp open rendezvous( what is this ?! )
5000/tcp open UPnP( what is this ?! )
MAC Address: 00:C8:E8:6A (Apple Computer)
Interesting ports on 192.168.0.103:
Not shown: 1677 closed ports
PORT STATE SERVICE
515/tcp open printer
631/tcp open ipp ( what is this ?! )
5000/tcp open UPnP ( what is this ?! )
MAC Address: 00:16:CB:B7:DB (Apple Computer)
I would really appreciate any kind of help
Thanks!

Here's a list of "Well Known" TCP and UDP Ports Used By Apple Software Products...
http://docs.info.apple.com/article.html?artnum=106439
427 is SLP for Network Browser.
631 is Mac OS X Printer Sharing.
3689 is iTunes Sharing.
5000 is something to do with Windows...
http://www.grc.com/port_5000.htm
Might I suggest HenWen for watching/controlling your Ports/Activity?...
http://www.apple.com/downloads/macosx/networking_security/henwen.html

Help with opening a .PDF in browser (firefox) - have Adobe Acrobat 9 Pro Extender installed

Hi all,
I have Adobe Acrobat 9 ProExtender installed, whenever I go to my firefox options and change the .PDF setting to (USE ADOBE ACROBAT (in firefox)) setting, i get a screen which is whited out, and a message from Adobe Acrobat with a question mark (?), but no message is there to read.
That is the scr
een that pops up, I can back out and try the link again for it to work, but it does it to all my .PDF files I try to view on the page. All I can do to prevent this is to save to disk, and open with adobe acrobat pro extender, but sometimes the file I need to look at are quick and would save a lot of time just opening it on the browser.
Thanks for the help!

walker81 wrote:
Just change the windows settings that it should opens pdf files with Acrobat Pro (default).
http://support.microsoft.com/kb/307859
Unfortunately, it's not that simple because Acrobat and Reader share files, and that's why Adobe recommends not to have them both installed in the same machine.

Help with opening port 10000 on a pix 501

Similar Messages

Maybe you are looking for